SMART/PLUS CONTROL INSTALLATION & OPERATION INSTRUCTIONS SMART/PLUS BOX CONTENTS

Transcription

1 ir An r -Stea m SMART/PLUS CONTROL INSTALLATION & OPERATION INSTRUCTIONS SMART/REMOTE COMPATIBLE SMART/PLUS BOX CONTENTS 1. SMART/PLUS CONTROL 4. INSTALLATION & OPERATION MANUAL 7. ANCHORS (4) 2. CONTROL CABLE 5. TEMPLATE 8. BLACK DECAL 3. TUBE OF SILICONE 6. SCREWS (4) 9. WHITE DECAL 1. LOCATING THE CONTROL INSIDE OR OUTSIDE THE STEAMBATH ENCLOSURE: The SMART/PLUS control is designed to be installed inside the steambath enclosure. However, if it is necessary to install the SMART/PLUS outside the steambath enclosure, a separate kit (#MSNC) must be obtained by contacting Mr. Steam at STEAM. 2. INSTALLATION OF THE CONTROL INSIDE THE STEAMBATH ENCLOSURE: It is highly recommended that the SMART/PLUS control is located four to five feet above the floor. The control should be away from direct shower spray and must be away from the steam source, preferably on an opposite wall from the steam head. The Control should also be kept away from hot water piping and steam piping. 3. DETERMINE IF THE INSTALLATION OF AN ELECTRICAL BOX IS REQUIRED: The SMART/PLUS control operates on a 24 VAC low voltage signal for safety. Check your local building codes to determine if the use of an electrical box is required. 4. USING THE SMART/PLUS CONTROL WITH A SMART/REMOTE CONTROL: The SMART/REMOTE is an optional accessory control which extends the ON/OFF feature to a selected location outside the steambath enclosure. For additional information about the SMART/REMOTE control, call Mr. Steam at STEAM. If the optional SMART/REMOTE control is to be used then follow instructions provided with the SMART/REMOTE control. Do not proceed to install the SMART/PLUS control without the SMART/ REMOTE instructions. 5. A CAUTION: DO NOT ROUTE THE CONTROL CABLE INSIDE CONDUIT TOGETHER WITH POWER LINES OR CLOSE TO HOT WATER OR STEAM PIPING. DOING SO MAY RESULT IN A MALFUNCTIONING CONTROL. SUSSMANI ffe.sziyi&' IC It MR. STEAM IS A DIVISION OF SUSSMAN-AUTOMATIC CORPORATION th Street. Long Island City, NY 1111 (718) (8) FAX (718) WESTERN REGIONAL OFFICE: Sussman Automatic of California, Inc., 65 West Jefferson Blvd., Los Angeles, CA 916 (8) FAX (31) PUR 135 JUNE 97

2 STEP 1 PREPARE DESIRED LOCATION FOR THE SMART/PLUS CONTROL STEP 2 CONNECT THE CONTROL CABLE TO THE STEAM GENERATOR A. Remove template peeloff paper and attach the template to the wall in desired location. Drill and cutout as shown. Be exact. Clean all burrs and dust. CAUTION!!! TURN OFF ALL POWER TO THE STEAM GENERATOR UNTIL STEP 3C. FAILURE TO DISCONNECT POWER MAY RESULT IN AN INOPERABLE CONTROL. A. Connect the control cable (the end with the white connector) to the steam generator connector. TEMPLATE STEAM GENERATOR B. Route the control cable from the wall cutout to the steam generator. Locate the end of the cable that has the single black connector at the wall cutout. Locate the other end with the white connector at the steam generator. CONNECTOR CONTROL CABLE - -Th --- Th..._,, WHITE 4-PIN PLUG re-- WHITE 4-PIN JACK CONTROL CABLE STEP 5 APPLY SILICONE TO SMART/PLUS CONTROL STEP 6 MOUNT CONTROL TO WALL WITH SCREWS A. Make sure that the area around the cut out or electrical box is clean and free of debris. B. Run a bead of silicone along all four edges of the gasket as required to create seal between the gasket and the wall. SILICONE BEAD A. Make sure the THIS END UP" is pointed upward. B. Fully align insert the supplied screws into the face plate holes and with holes in wall. C. Keep the screws aligned and push the control against the wall until the adhesive gasket sticks firmly. D. Tighten the screws until the gasket is firmly secured against the wall. E. Remove excess silicone. SILICONE TUBE FACE PLATE HOLES _co ft,, e ----:: ,,, to91, v co i () -t v ~,,,,,,o MOUNTING SCREWS CONTROL FACE PLATE CONTROL CABLE

3 STEP 3 CONNECT THE CONTROL CABLE TO SMART/PLUS CONTROL STEP 4 EXPOSE ADHESIVE SURFACE ON BACK OF SMART/PLUS CONTROL II A. Firmly connect the black connector on the cable to the connector on the bottom of the SMART/PLUS circuit board. B. Check all power connections for proper installations. C. RESTORE POWER AND TEST THE OPERATION OF THE SMART/PLUS CONTROL ACCORDING TO THE OPERATION INSTRUCTIONS ON BACK COVER OF THIS INSTALLATION GUIDE. DO NOT EXPOSE CONTROL TO STEAM DURING TEST. D. AFTER POSITIVE TEST RESULTS proceed to STEP 4. If test results are negative review installation. Mr Steam 8 \ SUSSMAN AUTOMAT1ECORP. 4-PIN PLUG i 4-PIN JACK Remove paper liner from back of SMART/PLUS control to expose adhesive surface. Discard paper liner. EXPOSED ADHESIVE SURFACE Mr SUSS Stecl Mgi AN A uto c GEAR Emagge POrn ', 4" P. - CONTROL CABLE PAPER LINER (DISCARD) STEP 7 ALIGN DECAL AND REMOVE BOTTOM PEEL-OFF SECTION STEP 8 SECURE DECAL TO FACE PLATE A. Align bottom edge of TAB A (top tab) with top of control. B. Remove TAB B (bottom tab) along with the peel-off paper and rub down exposed adhesive onto face plate. TAB A A. Remove TAB A along with peel-off paper and rub down top section of decal. TAB A AND TOP PEEL-OFF SECTION A-- - _ ALIGN.44*Elysiet.k NSt,,,,,,, DECAL a --- N z_- -z _ ,-. -, % =--, May IP S TAB B AND BOTTOM PEEL-OFF SECTION _

4 SMART/PLUS OPERATION Depress and release the "ON" button. The SMART/PLUS control will display the TIME & TEMPERATURE settings. Steam will begin flowing out of the steam head after approximately five minutes. Steam will continue flowing for the duration of the indicated time setting and the temperature will be maintained at the indicated temperature setting. The butler logo lights up in the "ON" mode. 2) CONTROL "OFF" Depress and release the "OFF" button and the control will turn off and the steam will stop flowing. The TIME & TEMPERATURE settings are reset and the memory is erased (see MEMORY). The butler logo is off during this mode. 3) CONTROL "PAUSE" Depress and release the "PAUSE" button and the steam will stop flowing but the time cycle will continue to count down. The butler logo will blink on and off. Press the "PAUSE" button again to renew the steam flow. The "PAUSE" feature allows the steambather to temporarily stop the steam flow. 4) CONTROL "TIME" - SETTING THE DURATION OF THE STEAMBATH Depress and release the "TIME" button to set the desired duration of the steambath. Each activation of the button will increase the duration of the steambath by (1) minutes. Time is set in increments of (1) minutes, starting from (1) minutes up to a maximum of (6) minutes. When the maximum duration of (6) minutes has been exceeded the time will reset at (1) minutes. The time setting is visually indicated by the illuminated bar graph and an gdivont linio v116 (see diagram below). The time setting can be changed to a new setting at any time during the steambath. Note that the steam generator features a (75) minute shut-off as an automatic safety backup device. OBSERVING REMAINING STEAMBATHING TIME The remaining steambath duration is visually indicated by the illuminated bar graph and an adjacent time scale (see diagram below). After (1) minutes of elapsed time the bar graph will jump down to the next lower increment to display remaining time. 5) CONTROL "TEMPERATURE" - SETTING THE STEAMBATH TEMPERATURE Depress and release the "TEMPERATURE" button to set the desired steambathing temperature. Each activation of the button will increase the temperature of the steambath by (2) degrees. Temperature is set in increments of (2) degrees from (11) degrees up to a maximum of (12) degrees. When the maximum temperature setting of (12) degrees has been exceeded, the temperature will reset at (11) degrees. The temperature setting is visually indicated by the illuminated bar graph and an adjacent temperature scale (see diagram below). The temperature setting can be changed to a new setting at any time during the steambath. 6) MEMORY The SMART/PLUS control automatically stores and displays the last preferred TIME and TEMPERATURE settings for the next steambath. [Note: If the OFF button is activated during a steambath, the memory is erased and a steambath will start with a default setting of (3) minutes and (114) degrees.] ILLUMINATED TEMPERATURE BAR GRAPH ILLUMINATED TIME BAR GRAPH TEMPERATURE TIME SCALE SCALE INDICATOR LIGHT

5 INSTALLATION TEMPLATE MR STEAM a division of SUSSMAN-AUTOMATIC CORPORATION th Street, Long Island City, N.Y TEL (718) (8) 76-STEAM DRILL L.( INSTRUCTIONS CUTOUT 1. TEMPLATE IS FOR INSTALLATIONS THAT DO NOT REQUIRE I A JUNCTION BOX I 2. IF THE CONTROL IS LOCATED INSIDE THE STEAMBATH IT I MUST BE INSTALLED AWAY FROM THE STEAMHEAD. 3. PEEL OFF THIS TEMPLATE AND STICK TO WALL IN DESIRED LOCATION.. 4. DRILL AND CUTOUT AS SHOWN. DO NOT OVERSIZE CUTOUT. 5. REMOVE TEMPLATE AND DISCARD I 6. DO NOT STICK THIS TEMPLATE ON FINISHED WALLS THAT MAY BE DAMAGED BY THE ADHESIVE BACKING. 1 L --4(--- DRILL-31141a- I. PUR

6 11./7I-Ste r-7-7 Sept 97 PUR 177 perature sen structions for installing the remote tem or PN N/I 5NG. NOTE: DO NOT INSTALL THE SMART/TWO OR SMART/PLUS CONTROL BEFORE THE REMOTE TEMPERATURE SENSOR IS CONNECTED. 1. Locate the remote temperature sensor about four to five feet above the floor. Locate the sensor away from direct steam or direct shower spray. 2. Drill a 7/32" hole thru the wall. 3. Fill the hole with silicone ( provided) 4. Insert the temperature sensor with 1/4" of the probe exposed inside the steam room as shown in diagram #1. 5. Remove all silicone from the exposed sensor tip and wall. 6. Remove and discard the remote temperature jumper form the SMART/TWO or SMART/PLUS control. Connect the remote temperature cable connector control as shown in diagram #2. 4 STEAMROOM INTERIOR TEMPERATURE PROBE PROBE CABLE ( CONNECT TO CONTROL) SILICONE SEALANT WALL DIAGRAM #1 Mr Steam SUSSMAN AUTOMATIC COPP. REMOTE TEMPERATURE PROBE CONNECTOR PE9CRE Thad RE ICre ppcaf PCNFA.OUTPUT SMART/TWO OR SMART/PLUS CONTROL V pm? g14,-11). 7 ISCSS1Lk.Ni Lifestyle IC R U P! DIAGRAM #7, MR. STE.4,14e) IS A DIVISION OF SUSSMAN-AUTOMATIC CORPORATION th Street, Long Island City, NY 1111 (718) (8) FAX (718) WESTERN REGIONAL OFFICE: Sussman Automatic of California, Inc., 65 West Jefferson Blvd., Los Angeles, CA 916 (8) FAX (31)