INSTALLATION INFORMATION
|
|
- John Ralph Phillips
- 5 years ago
- Views:
Transcription
1 INSTALLATION INFORMATION BMS ZE6000i-PCBT.xxxx / ver. 2 Programmable battery management system for Lithium Ion battery cells, for up to 32 round or prismatic cells, 10 to 400Ah NOTE: This installation guide applies to the micro lithium ion battery management system, part number ZE6000i, and associated modules. For explanation of terms used, acronyms & a glossary, refer the the lithium ion battery management system application note, document code You are strongly advised to read through this application note before attempting system installation. Also, be sure that you are fully conversant with the safety issues surrounding lithium-ion batteries. There are some notes in the application note to assist understanding, but these should not be considered to be a complete & authoritative source of information. You are entirely responsible for ensuring that you understand these issues & comply with best practice when putting together a battery system. Only technically competent persons should attempt to install this system!
2 Table of Contents Description This BMS comprises one master module, along with a range of additional expander modules. The battery management system is organized into groups of four cells, this being referred to as a bank. The master is configured to manage either one or two banks, with additional banks being catered for by the addition of expander modules. Any added expander modules are also managed by the master BMS, with a maximum capacity of 32 cells in total. The primary user interface is a 20 character x 4 line OLED display with a touchscreen style user input key. The display also houses a light sensor for automatic adjustment of the display to suit the ambient light level. BMS configuration parameters may be changed by authorized users through a configuration webpage. The configuration webpage has two permission levels allowing parameter changes. These are engineer & system integrator. Module identification BMS master module User display
3 Lithium-ion battery safety Lithium ion batteries are capable of both absorbing & delivering extremely high current. Excess current may cause overheating or burning of connected circuits, the battery itself can also suffer damage with fire & toxic emissions a possible outcome. Although the BMS includes overcurrent detection, the external contactors may not be capable of breaking the short circuit current without welding in the closed position. It is vital to provide fail-safe protection of last resort. A conventional fuse is one appropriate means of providing this protection. The fuse must be capable of breaking the fault current & the fault current must always be able to rupture the fuse. Information provided by both the battery & fuse manufacturer should enable correct part selection. Wiring loom BMS wiring looms are included with the complete BMS system. The BMS wiring looms are also available separately. The installer may also make up looms based on the information supplied in this manual. Connection sequence The BMS must be connected to the battery pack in the sequence set down below. Failure to follow this sequence may cause damage to the BMS. The sequence assumes that the individual cells have already been assembled into the battery stack and wired together and that the component parts such as relays & contactors have been mounted into the pack. More complete wiring details are provided in the sections that follow & it is advisable to refer to them before commencing installation. 1. Connect one side of the current shunt power terminals to the battery stack negative terminal. 2. Connect the BMS common 0V to the ground side power terminal of the current shunt. 3. Before plugging the current shunt loom into the BMS, wire it to the current shunt sense terminals. 4. The following looms may be wired next; the connection sequence of these looms is not critical, but do not plug them into the BMS at this stage unless stated: temperature sensors - can be plugged into the BMS at this point cell monitors - wire to individual cells as shown in the wiring diagram display - can be plugged into the BMS at this point (if used) external relays & contactors - wire to relays & contactors as shown in the wiring diagram 5. The load & charger sense wires may now be connected to the BMS terminal block. There are two terminal blocks on the BMS, marked Cn2 & Cn3. Cn2 (lo) is used when a four cell stack (12V) is to be managed.cn3 is used when an eight cell stack (24V) is to be managed. If the system includes expander modules to cater for more than eight cells, then the terminal block on the highest expander in the stack is used. For details, refer to the expander installation manual. 6. First connect the load wire from the BMS to the load connection point - refer to the wiring diagrams. 7. Next, connect the charger wire from the BMS to the charger connection point - refer to the wiring diagrams. 8. Finally plug the cell monitor ribbon cable connector into the BMS - at this point the BMS will power up & is ready for configuration, if required. 9. Configuration instructions are provided in document no C
4 Configuration overview Figure 1: overview of system connectors
5 Configuration overview - continued Figure 2: overview of system connectors which have configuration options
6 Configuration overview - continued Figure 3: generic power system architecture Charger disconnect: For safe & proper management of lithium-ion battery packs, both the loads & the charging source must be controlled so as to restrict battery operation to within prescribed limits. There is no float charge condition, as there is with lead-acid batteries. Charging must be terminated when the battery reaches 100% state of charge; any overcharging will cause irreversible damage. Hence, some form of charge disconnect must be provided. Some chargers designed for use with lithium ion may have appropriate built-in charge management, but be aware that this must be configured for the specific cell in use. Variations of cell electrode composition between manufacturers means that there is no one-size-fits-all regime. The BMS may be used with a suitable intelligent charger, configured for the specific battery cell type. The BMS may also be used with a suitably set constant voltage source for charging; the BMS provides a charge on/off capability to protect the battery pack. This may be accomplished using a relay or contactor which may be located at the charger output, as shown above. The relay or contactor may instead be located at the charger input, provided the charge source is able to operate with the battery permanently connected and without any significant reverse loading. If the charger has an on/off control input, the BMS charger control output may be used to drive it.
7 Load disconnect: Load disconnection is required to protect the battery. The BMS can be configured to drive both normal contactors or relays, or twin-coil latching types. If the load has an on/off control input, the BMS consumers control output may be used to drive it, but be aware that the overcurrent disconnect relies on a reliable method of removing the load. If non-priority load shed is configured, a second relay or contactor will be required for the priority loads. Configuration overview - continued Figure 4: alternative charger control options, when not using an output side disconnector
8 Configuration overview - continued Figure 5: alternative DC/DC charger control options, when not using an output side disconnector
9 Configuration overview - continued Figure 5: alternative charger control options, when not using an output side disconnector
10 Wiring diagrams Figure 6: connectors right hand end of BMS
11 Wiring diagrams - continued Figure 7: connectors left hand end of BMS
12 Wiring diagrams - continued Figure 8: connectors right hand end of BMS
13 Wiring diagrams - continued Figure 9: overall wiring diagram for four-cell 12V systems, using charger output side relay and latching loads contactor
14 Wiring diagrams - continued Figure 10 & 11: overall wiring diagram for eight-cell 24V systems, using charger output side relay and latching loads contactor
15 Wiring diagrams - continued Figure 12 & 13: overall wiring diagram for four-cell 12V systems, using intelligent charger & latching loads contactor
16 Wiring diagrams - continued Figure 14 & 15: overall wiring diagram for eight-cell 24V systems, using intelligent charger & latching loads contactor
17 Wiring diagrams - continued Figure 17: general information, relay & contactor pin-out Wiring diagrams - continued Figure 18: user display & on/off control
18 Wiring diagrams - continued Figure 19: temperature sense & current shunt connections required for all systems
19 Wiring diagrams - continued Figure 20: cell monitoring connections, required for all systems 24 volt systems: This wiring diagram shows the connections for an 8 cell 24 volt pack. 12 volt systems: For 12 volt systems, there are two wiring options: 1. Simply leave the upper bank sense wires disconnected; cut back & insulate the ends. 2. The upper & lower bank sense wires may be parallel connected, so cell 5 sense wires go to cell 1 & so on. The parallel option doubles the balancing current, since the controllers now operate in tandem. The BMS must be configured to recognise the parallel connection as follows: Using the configuration tool, set up all parameters as if there were two banks; stack size set to 2, Then re-configure all parameters with exactly the same values, but with stack size set to 1. Note: Since incorrect settings for the BMS may damage the battery with the risk that the battery may rupture, only qualified persons may change settings using the configuration tool.
20 Powering up the system Figure 21: inserting the cell sense connector powers up the BMS. Only do this once all other connections are in place and have been checked.
21 Specifications These specifications are subject to change without notice & do not form part of any contract. Parameter Default value Range (configuration) Notes Engineer Permissions Cell undervoltage threshold 2.55 volts 2.0 to 4.7 volts Cell overvoltage threshold 3.50 volts 2.0 to 4.7 volts Balancer forced on voltage 3.60 volts 2.0 to 4.7 volts Charge high temperature limit 45ºC 1ºC to 70ºC Discharge high temperature limit 55ºC 1ºC to 70ºC Charge low temperature limit 0ºC -20ºC to +5ºC Discharge low temperature limit -20ºC -30ºC to +5ºC Fan start temperature 35ºC 20ºC to 50ºC Fan stop temperature 30ºC 20ºC to 50ºC SOC for charger on 90.00% 10 to 100% note 4 Current for SOC synchronisation 18 amps 1 to 40 amps note 5 Charger volts per cell 3.7 volts per cell 3 to 5 volts per cell note 6 Rated battery capacity 100Ahr 20 to 400 Ahr Contactor configuration 6 7 options note 7 Stack size 1 1 = 12V up to 8 = 96V Remote display fitted fitted/not fitted Battery monitor fitted fitted/not fitted Current shunt mv 50mV 1 to 60mV note 8 Current shunt amps 500 amps 1 to 800 amps note 8 Maximum peak charging current 100 amps 10 to 800 amps note 9 Maximum mean charging current 100 amps 10 to 800 amps note 10 Maximum peak discharge current 200 amps 10 to 800 amps note 11 Maximum mean discharge current 100 amps 10 to 800 amps note 12 COM port number 6 COM 1 to COM 12 note 13 Configuration reference 1 integer, 1 to 200 note 14 Notes: Integrator The BMS settings are installed using the configuration webpage, which is only available for qualified persons. The BMS reports its settings, along with present battery status information via the serial port or via bluetooth if
22 installed. These data may be viewed by any user by logging in as Guest in the configuration web-page. Configuration permissions - the configuration webpage has two permission levels allowing parameter changes; these are engineer & installer. Engineers can change all configurable parameters, whereas installers (system integrators) have limited options. Guests can view all details, but not make changes. Once the battery has been charged, recharge is not enabled until the battery state of charge has fallen to this level. Once the recharge current has fallen to this level, the state of charge is reset to 100% The open-circuit or off load charger voltage This parameter defines the configuration of the output power drivers. The ratings for the external battery current shunt, used to track state of charge, Threshold for the peak battery charging current, above which the charger will be disconnected. Threshold for the mean battery charging current, above which the charger will be disconnected; short term peaks are disregarded unless they exceed the maximum peak charging current setting. Threshold for the peak battery discharge current, above which the loads will be disconnected. Threshold for the mean battery discharge current, above which the loads will be disconnected.; short term peaks are disregarded unless they exceed the maximum peak discharge current setting. This is the COM port that will be used for serial connection with a PC. This a number that can be used to identify the BMS system & is appended to the bluetooth identity so that a particular pack can be identified when a connection is established. Serial port These are the COM port settings that are used by the BMS: Baud: Parity : none Databits : 8 Stop bits : 1 Flow control : none Encoding : ASCII.For complete information, consult the BMS configuration guide. BMS monitoring - using the optional bluetooth module First pair your monitoring device with the BMS bluetooth by searching for nearby devices. The BMS identity begins BMS followed by the BMS type & configuration reference. The bluetooth default passcode is all zeros ie 0000, although this may have been changed on your system. If 0000 is rejected, ask your system installer for the new passcode. Once paired & connected, you can monitor the bluetooth transmissions using either the bluetooth monitor webpage, or third party serial port capture software. Data can be received on Windows PC's, Android devices & other equipment that can receive the bluetooth data stream. The data is broadcast in plain English, but some control codes are also transmitted which may be displayed as text or symbols - these can be ignored
23 These are the settings that are used by the BMS for bluetooth: Baud: Parity : none Databits : 8 Stop bits : 1 Encoding : ASCII
80V 300Ah Lithium-ion Battery Pack Data Sheet
80V 300Ah Lithium-ion Battery Pack Data Sheet 80 V, 300 amp-hour capacity, maintenance-free energy storage, IP65 design, fully integrated BMS, integrated fuse and safety relay protection, highly configurable
More informationUser Manual. BMS123 Smart
User Manual BMS123 Smart Introduction After the introduction of affordable LiFePO4 batteries, off-grid solutions became available for wide public. It is vital that such batteries are charged very carefully.
More informationLITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power
LITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power Issued Date > 2016-04-13 Issued Version > V00 1. General Information This specification defines the performance of rechargeable LiFePO4
More informationLITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power
LITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power Issued Date > 2016-01-18 Issued Version > V00 1. General Information This specification defines the performance of rechargeable LiFePO4
More informationEclipse Solar Suitcase
Eclipse Solar Suitcase Renogy 100W 200W 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 Version 1.0 Important Safety Instructions Please save these instructions. This manual contains important
More informationLITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power
LITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power Issued Date > 2016-04-25 Issued Version > V01 1. General Information This specification defines the performance of rechargeable LiFePO4
More informationLITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power
LITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power Issued Date > 2016-02-24 Issued Version > V01 1. General Information This specification defines the performance of rechargeable LiFePO4
More informationBMS-LiFePower. 123SmartBMS. Instruction manual
BMS-LiFePower 123SmartBMS Instruction manual Index Introduction...2 Keep the batteries in perfect condition...2 Package contains (12 Volt, 4 cells)...3 Specs...3 Placing the cell modules...4 Mounting the
More informationManual. EN Appendix. Lynx Ion BMS 400A / 1000A
Manual EN Appendix Lynx Ion BMS 400A / 1000A 1. SAFETY INSTRUCTIONS 1.1 In general Please read the documentation supplied with this product first, so that you are familiar with the safety signs en directions
More informationSimpliPhi Power PHI Battery
Power. On Your Terms. SimpliPhi Power PHI Battery INTEGRATION GUIDE: VICTRON Optimized Energy Storage & Management for Residential & Commercial Applications Utilizing Efficient, Safe, Non-Toxic, Energy
More informationEV Power - Battery Control Unit Instructions. 8 Cell 24V
EV Power - Battery Control Unit Instructions. 8 Cell 24V PAGE 1 OF 12 BCU-EVPPAK Features - Simple to install and use, microprocessor control. - Low power requirement, just 15mA when switched on with relay
More information12V 1 AMP (1000 ma) Automatic Battery Charger & Maintainer
12V 1 AMP (1000 ma) Automatic Battery Charger & Maintainer For lead-acid batteries THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR 12V BATTERY CHARGER: YUA1201000 / INT1201000 KEEP
More informationAdvanced Information Subject to Changes
Advanced Information Subject to Changes High Efficiency 30/60V, 100 Amps Active Management System for Lithium Ion Batteries Roboteq s is a battery management system designed for building cost-effective,
More informationINTRODUCTION. Specifications. Operating voltage range:
INTRODUCTION INTRODUCTION Thank you for purchasing the EcoPower Electron 65 AC Charger. This product is a fast charger with a high performance microprocessor and specialized operating software. Please
More informationLithium Power Pack LITHIUM-ION BATTERY SYSTEM. With epro Plus Battery Monitor
Lithium Power Pack LITHIUM-ION BATTERY SYSTEM With epro Plus Battery Monitor LITHIUM-ION BATTERY SYSTEM After 2 years of research, testing and proving, and a further 5 years of infield sales, Enerdrive
More informationRover Series. Rover 20A 40A Maximum Power Point Tracking Solar Charge Controller
Rover Series Rover 20A 40A Maximum Power Point Tracking Solar Charge Controller 0 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 Version 1.5 Important Safety Instructions Please save these
More informationLITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power
LITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power Issued Date > 2017-07-26 Issued Version > V00 1. General Information This specification defines the performance of rechargeable LiFePO4
More informationLITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power
LITHIUM IRON PHOSPHATE BATTERY Multi-application - LiFePO4 Power Issued Date > 2017-04-19 Issued Version > V00 1. General Information This specification defines the performance of rechargeable LiFePO4
More informationNeverDie Battery Management System Section 1: Overview
Section 1: Overview PURPOSE: A Battery Management System or BMS Protects the Battery From Being Damaged by External Sources A BMS Protects the User and the External Sources from a Failed Battery A BMS-Based
More information123\SmartBMS. 123\SmartBMS manual V1.3. Albertronic BV The Netherlands
123\SmartBMS 123\SmartBMS manual V1.3 Index Introduction... 2 Keep the batteries in perfect condition... 3 Package contents... 4 Specifications... 4 Placing the cell modules... 5 Mounting the IN Module...
More informationBMS16 v cell Lithium Battery Management System
ZERO EMISSION VEHICLES AUSTRALIA http://www.zeva.com.au Safety Warning Although 8-16 cell lithium battery packs do not involve lethal voltages, they frequently involve dangerous amounts of current and
More informationUser Manual 123electric Battery Management System 123\BMS Revision 1.4 Augusts 2015
User Manual 123electric Battery Management System 123\BMS Revision 1.4 Augusts 2015 Table of contents Introduction... 3 System structure... 3 Keep the batteries in a perfect condition : ALWAYS!... 5 Specifications...
More informationTypes batteries. AGM Gel OpZs OpZv Lead Carbon LiFePO4 NCA Saltwater Zinc Bromine Etc,etc, etc, etc, etc, etc,
Batteries Types batteries AGM Gel OpZs OpZv Lead Carbon LiFePO4 NCA Saltwater Zinc Bromine Etc,etc, etc, etc, etc, etc, Today focus on Victron batteries AGM Gel OpZs OpZv Lead Carbon LiFePO4 NCA Saltwater
More informationPV Master OPERATION MANUAL
PV Master OPERATION MANUAL GoodWe Technical Services Center December, 2017 Ver. 1.00 BRIEF INTRODUCTION PV Master is an external application for GoodWe inverters to monitor or configure inverters or to
More informationOPTI-Solar SC MPPT Series
www.opt i -sola r. c o m OPTI-Solar SC MPPT Series SOLAR CHARGE CONTROLLER SC-50 / SC-80 / SC-80X / SC-160X MPPT Installation and Operation Manual CONTENTS Introduction... Feature... Specification... Dimension...VII
More informationThe Traveler Series TM : Adventurer
The Traveler Series TM : Adventurer 30A PWM Flush Mount Charge Controller w/ LCD Display 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 Version: 3.4 Important Safety Instructions Please save
More informationINVERTEK WINDTAR MPPT SERIES
利佳興業股份有限公司 RICH ELECTRIC CO.,LTD. INVERTEK WINDTAR MPPT SERIES WIND MPPT CHARGER WS-120CX / WS-80CX / WS-50CX Installation and Operation Manual MANUAL VER.1, 31-Dec-2010 CONTENTS Introduction...Ⅳ Feature...
More informationPowerterm L120C Single Output PSU/Battery Chargers Model C2199A-1 (12V/8A) or Model C2199A-2 (24V/6A)
A Complete solution for small battery-backed dc instrument power systems. DATASHEET Supply 12Vdc 8A or 24Vdc 6A loads Ideal for RTU s, dataloggers, remote field instrumentation, alarm systems, etc. where
More informationOrion 2 BMS Operation Manual
www.orionbms.com Orion 2 BMS Operation Manual The Orion BMS 2 by Ewert Energy Systems is the second generation of the Orion BMS. The Orion BMS 2 is designed to manage and protect Lithium ion battery packs
More informationUser manual. BMS123 Smart
User manual BMS123 Smart Introduction After the introduction of affordable LiFePO4 batteries, off-grid solutions became feasible. It is vital that such batteries are charged very carefully. In other words,
More information10A 15A 25A 40A 60A 20A 30A
12V-60A 24V-30A New robust and compact casing 3 Completely isolated battery outputs Easy wiring and connections thanks to the Winsta (Wago) and Phoenix contact connectors Digital management with up to
More informationIssue 2.0 December EPAS Midi User Manual EPAS35
Issue 2.0 December 2017 EPAS Midi EPAS35 CONTENTS 1 Introduction 4 1.1 What is EPAS Desktop Pro? 4 1.2 About This Manual 4 1.3 Typographical Conventions 5 1.4 Getting Technical Support 5 2 Getting Started
More informationTRIPS AND FAULT FINDING
WWW.SDS.LTD.UK 0117 9381800 Trips and Fault Finding Chapter 6 6-1 TRIPS AND FAULT FINDING Trips What Happens when a Trip Occurs When a trip occurs, the drive s power stage is immediately disabled causing
More informationHarris IRT Enterprises Digital Resistance Tester Model XP
Harris IRT Enterprises Digital Resistance Tester Model 5012-06XP Specifications & Dimensions 2 Theory of Operation 3 Operator Controls & Connectors 4 Test Connections 5 Calibration Procedure 6-7 Options
More informationThe Traveler Series: Adventurer
The Traveler Series: Adventurer RENOGY 30A Flush Mount Charge Controller Manual 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 Version: 2.2 Important Safety Instructions Please save these instructions.
More informationLiFePO4 Battery (Bluetooth) Specification
LiFePO4 Battery (Bluetooth) Specification Model: TB-BL12300F-S103A_00 SHENZHEN TOPBAND NEW ENERGY CO.,LTD Address: Topband Industrial Park,Liyuan Industrial Zone,Shiyan,Bao'an,Shenzhen, China,518108. Web:
More informationEnerdrive Lithium-Ion Battery System
Enerdrive Lithium-Ion Battery System After 2 years of research, testing and proving, and a further 2 years of infield sales, Enerdrive has designed and created a COMPLETE Lithium Battery & Installation
More informationDycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD
Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain
More informationMagellan Utility Scale Energy Storage
Magellan Utility Scale Energy Storage MAGELLAN ESU 2 Supplying industry since 1992 Built for harsh environments Rugged industrial design Magellan Power ESU Series of Utility Scale Energy Storage combines
More informationElite Power Solutions Automatic Battery Control (ABC) Operation Manual
Elite Power Solutions Automatic Battery Control (ABC) Operation Manual Elite Power Solutions 335 E Warner Rd. STE 3 Chandler, AZ 85225 www.elitepowersolutions.com ABC Operation Manual Page 1 Table of Contents
More informationPhosphate-base Lithium-ion Battery Pack Model:LFP V 1350Ah Product Specifications Lithium Energy Solution 1/8
Phosphate-base Lithium-ion Battery Pack Model:LFP1350-48 48V 1350Ah Product Specifications Lithium Energy Solution 1/8 1. Product overview LFP1350-48 Products are mainly for customized development of high
More informationBMS 12/200 for 12,8 Volt lithium iron phosphate batteries Especially designed for vehicles and boats
BMS 12/200 for 12,8 Volt lithium iron phosphate batteries Especially designed for vehicles and boats www.victronenergy.com Why lithium-iron phosphate? Lithium-iron-phosphate (LiFePO4 or LFP) is the safest
More informationPulsar Evolution 1500 / 1500 Rack 1100 / 1100 Rack 800 / 800 Rack 500 Rack
www.mgeups.com MGE UPS SYSTEMS Pulsar Evolution 1500 / 1500 Rack 1100 / 1100 Rack 800 / 800 Rack 500 Rack Installation and user manual S T O P Y O U N O W L L W I N G I T H N O 34007117EN/AB - Page 1 Page
More informationEPAS Desktop Pro Software User Manual
Software User Manual Issue 1.10 Contents 1 Introduction 4 1.1 What is EPAS Desktop Pro? 4 1.2 About This Manual 4 1.3 Typographical Conventions 5 1.4 Getting Technical Support 5 2 Getting Started 6 2.1
More informationSECTION DC POWER SUPPLY/BATTERY CHARGER
SECTION 26 33 05 PART 1 - GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide the single-phase heavy-duty industrial battery charger and all accessories required, complete and operable, in accordance
More informationOperating and programming instructions at =AMPS or =WATTS REPLACED PERCENTAGE FROM LAST DISCHARGE
TM-2030 TriMetric Battery Monitor Installation and User Guide TM 2030-RV Bogart Engineering CHARGING BATTERY REMINDERS when flashing-meets "CHARGED" criteria =TIME TO CHARGE =TIME FULL TO EQUALIZE =BATT.
More informationDigital-Control and Programmable DC Power Supply Models: , , , & User Manual
Digital-Control and Programmable DC Power Supply Models: 72-2535, 72-2540, 72-2545, 72-2550 & 72-10480 User Manual Page 19/05/16 V1.0 Safety Symbols This chapter contains important safety instructions
More informationHow To Set Up SimpliPhi Batteries Using OutBack Chargers
Introduction How To Set Up SimpliPhi Batteries Using OutBack Chargers The main focus of this application note will be on setting up OutBack charging sources for best operational performance for SimpliPhi
More informationDIN-Rail DC UPS. Powers Loads and Charges Back-Up Battery, Ideal for Automation and Wireless System Transmitter Applications
DIN-Rail DC UPS Powers Loads and Charges Back-Up Battery, Ideal for Automation and Wireless System Transmitter Applications Combines all system power functions: power supply, battery charger, UPS circuitry
More information620 Magnolia Avenue Suite B Ontario, CA (909) Diagnostic and Troubleshooting. Golf Cart. Revision: A Date:
620 Magnolia Avenue Suite B Ontario, CA 91762 (909) 923-1973 Diagnostic and Troubleshooting Golf Cart Revision: A Date: 9-25-13 Diagnostics Diagnostics information can be obtained by observing the fault
More informationSOLAR SMART. 12/24V 20Amp MPPT Solar Charge controller with Ethernet
SOLAR SMART 12/24V 20Amp MPPT Solar Charge controller with Ethernet Embedded web pages, SNMP support, output port for external Relay board and GSM SMS unit port USER MANUAL PLEASE READ THIS MANUAL CAREFULLY
More informationFreedom egen System End-of- Line Functional Checklist
U Freedom egen System End-of- Line Functional Checklist 976-0361-01-01 Rev A April 2018 DANGER RISK OF FIRE, ELECTRIC SHOCK, EXPLOSION, AND ARC FLASH This checklist is in addition to, and incorporates
More informationHarness the Power of the Sun
Harness the Power of the Sun Solar Controller / Battery Charger User s Manual Nominal Voltage: 12Volts Rated Solar Current: 30Amps / 40Amps Nominal Voltage: 12Volts / 24Volts Auto Rated Solar Current:
More informationTechnical Note. Management of Sealed Lead Acid Batteries in Reliable Small DC Standby Power Supply Systems
Technical Note Management of Sealed Lead Acid Batteries in Reliable Small DC Standby Power Supply Systems Automation Products Introduction As more and more remote monitoring is installed on sites ranging
More informationPulsar Evolution 2200/3000/3000 XL
www.mgeups.com Pulsar Evolution 2200/3000/3000 XL Installation and user manual MGE UPS Systems 1660 Scenic Avenue Costa Mesa, CA 92626 (714) 557-1636 For service call 1-800-438-7373 www.mgeups.com IMPORTANT
More informationUP100AC INSTRUCTION MANUAL
UP100AC AC/DC Charger INSTRUCTION MANUAL 100W 10A TABLE OF CONTENTS Introduction... 2 Special Features... 4 Warning and Safety Notes... 6 Lithium Battery Connection Diagram... 10 Operation Diagram - Homepage...
More informationBMS RS-485 Card/Box Quick Guide Applicable for hybrid inverter 3KW-10KW
Thank you for purchasing RS485 card/box. This manual contains instructions and warnings that should be followed during the installation, operating and storage of the card. Please keep this manual for further
More informationUser Manual Solar Charge Controller 3KW
User Manual Solar Charge Controller 3KW Version: 1.3 CONTENTS 1 ABOUT THIS MANUAL... 1 1.1 Purpose... 1 1.2 Scope... 1 1.3 SAFETY INSTRUCTIONS... 1 2 INTRODUCTION... 2 2.1 Features... 2 2.2 Product Overview...
More informationTable of Contents. 350 V, 80 kw, 20 kwh, traction battery pack, specifications
350 V, 80 kw, 20 kwh, traction battery pack, specifications Table of Contents 1 Description...2 2 Block diagram...3 3 Electrical Specifications...4 Pack...4 Charger...5 DC-DC converter...5 4 Mechanical
More informationBATTERY BOOSTER/CHARGER MODEL NO: DIGICAR 900
BATTERY BOOSTER/CHARGER MODEL NO: DIGICAR 900 PART NO: 6261205 OPERATION & MAINTENANCE INSTRUCTIONS LS0715 INTRODUCTION Thank you for purchasing this CLARKE Battery booster / charger which is suitable
More information1700W Solar Battery Charger Maximum Power Point Tracker
Page 1 of 8 This revolutionary maximum power point tracker solar charger was designed using the technology that won GSL Electronics the prestigious EDN Innovation Awards 08 and 09 and the Greentech Consensus
More informationASPIRO & GUARDIAN BATTERY MANAGEMENT WITH ACC EXTENDED CONTROLLER
DESCRIPTION Battery management is implemented in the Aspiro and Guardian DC Power Systems using the ACC Extended (ACX) controller. ASPIRO & GUARDIAN BATTERY MANAGEMENT WITH ACC EXTENDED CONTROLLER The
More informationAPPLICATION NOTE: CLOSED LOOP INTEGRATION WITH XANBUS ENABLED SCHNEIDER ELECTRIC CONEXT PRODUCTS
APPLICATION NOTE: CLOSED LOOP INTEGRATION WITH XANBUS ENABLED SCHNEIDER ELECTRIC CONEXT PRODUCTS 1. Safety 3 1.1 Warnings, Cautions and Notes 3 1.2 General Warning 1.3 Fire Risk 3 1.4 Electric Shock Risk
More informationUsing Apollo Solar Remote Monitoring Software
Using Apollo Solar Remote Monitoring Software Apollo Solar, Inc. 23 F. J. Clarke Circle Bethel, Connecticut 06801 USA +1 (203) 790-6400 www.apollosolar.com 1 Overview We will see how all the components
More informationLiFePO4 Battery(Bluetooth) Specification
LiFePO4 Battery(Bluetooth) Specification Model: TB-BL1240F-S110A SHENZHEN TOPBAND NEW ENERGY CO.,LTD Address: Topband Industrial Park,Liyuan Industrial Zone,Shiyan,Bao'an,Shenzhen, China,518108. Web: www.topband.com.cn
More informationECT Display Driver Installation for AP2 Module
ECT Display Driver Installation for AP2 Module Overview The ECT Display Driver is a small module with a removable wire harness that mounts behind the driver's foot well cover. All wiring connections are
More informationLiFePO4 Battery(Bluetooth) Specification
LiFePO4 Battery(Bluetooth) Specification Model: TB-BL1220F-S115D SHENZHEN TOPBAND NEW ENERGY CO.,LTD Address: Topband Industrial Park,Liyuan Industrial Zone,Shiyan,Bao'an,Shenzhen, China,518108. Web: www.topband.com.cn
More information12/24 VOLT AUTOMATIC SOLAR CHARGE CONTROLLER
12/24 VOLT AUTOMATIC SOLAR CHARGE CONTROLLER P/No.s SC320 & SC330 WARNING Please read these instructions completely prior to installation. Lead acid batteries can be dangerous. Ensure no sparks or flames
More informationAUTO CHARGE 4000 MODEL #: LOW PROFILE CHARGER AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 4000 LOW PROFILE CHARGER AUTOMATIC DUAL OUTPUT BATTERY CHARGER Unit supplied with this display MODEL #: 091-89-12 INPUT: 120 Volt, 50/60 Hz, 5 Amps OUTPUT: 45 Amps File:
More informationCYCLE LIFE 12V 5AH LITHIUM ION BATTERY RB5 LITHIUM ION BATTERY CAPACITY AT DIFFERENT CYCLES AT 100% DOD 99.
RB5 LITHIUM ION BATTERY RB10 LITHIUM ION BATTERY 3.75 in. 95.25 mm CYCLE LIFE CAPACITY AT DIFFERENT CYCLES AT 100% DOD 100 cycles 500 cycles 99.7 96.3 1000 cycles 90.8 2 in. 50.8 mm 5.9 in. 149.86 mm 1500
More informationLithium Power Supply
Lithium Power Supply User Manual LPS 1200W-60Ah LPS 1500W-100Ah LPS 2500W-100Ah Compact lithium battery based power supply - for easy acces to 230V and 12V energy, everywhere! V1.1 Safety Instructions
More informationCruising Charger Series OWNER S MANUAL
R Cruising Charger Series OWNER S MANUAL ON BOARD BATTERY CHARGERS Models DC Amperage No. Of Banks Volts 2614A 5,10 Amps 2 Bank 12/12 2614A-230 2621A 5,5,10 Amps 3 Banks 12/12/12 2621A-230 2622A 10,10
More informationUser Manual. Solar Charge Controller 3KW
User Manual Solar Charge Controller 3KW 1 CONTENTS 1 ABOUT THIS MANUAL... 3 1.1 Purpose... 3 1.2 Scope... 3 1.3 SAFETY INSTRUCTIONS... 3 2 INTRODUCTION... 4 2.1 Features... 4 2.2 Product Overview... 5
More informationManual. Lynx Ion 24V/180Ah Lithium Ion Batteries
Manual EN Lynx Ion 24V/180Ah Lithium Ion Batteries Copyrights 2012 Victron Energy B.V. All Rights Reserved This publication or parts thereof, may not be reproduced in any form, by any method, for any
More informationPV Charge Controller SBC-7108 / 7112 / 7120
PV Charge Controller SBC-7108 / 7112 / 7120 User's Manual NOTE: Please note that features like LCD read out of AH logging of 3 days (see Section 3.3) and 10 Night-light mode (see Section 4.3) are available
More informationE61, E63, E64 BMW AG - TIS
VS-42 je Baugruppe/Group: 61 meeknet.co.uk/e64 Power supply E60, E61, E63, E64 61 07 03 (029) weltweit Datum/Date: 06/2003 Update 02/2006 Introduction The power supply on the BMW 5- and 6-Series is similar
More informationSMT. Installation and Operation Manual. Model:SMT WITH MPPT TECHNOLOGY
SMT WITH MPPT TECHNOLOGY Installation and Operation Manual Model:SMT SMT Dimensions Specification Summary System Voltage 12 V/24V Rated Battery Current 12V, 5A 8A 10A 15A 20A 25A 24V, 5A 8A 10A 15A Rated
More informationtwin engine two battery bank split charge system
twin two battery bank split charge system P2331 12 volt. P2331 part number. 12331-0 24 volt. P2341 part number. 12341-0 contactor current rating continuous... 0 amp @ mv / contact / 0 A start... 0 amp
More informationAxpert-CSS AMTECH DRIVES Axpert-CSS Amtech
The Axpert-CSS is a range of Combination Soft Starter panels offered by AMTECH DRIVES. We also offer the module unit as an individual product, named as Axpert-Opti torque Soft Starter. This is only the
More informationMODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM
MODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM DSE 520 ISSUE 4 4/4/02 MR 1 TABLE OF CONTENTS Section Page INTRODUCTION... 4 CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.... 4 1. OPERATION...
More informationFLEXnet DC Programming & Guidelines
FLEXnet DC Programming & Guidelines PURPOSE: This document provides a detailed description of the FLEXnet DC Battery Monitor (FN-DC), its operation, and the best way to use it in different applications.
More informationBATTERY BOOSTER/CHARGER MODEL NO: DIGICAR 600
BATTERY BOOSTER/CHARGER MODEL NO: DIGICAR 600 PART NO: 6261200 OPERATION & MAINTENANCE INSTRUCTIONS LS0815 INTRODUCTION Thank you for purchasing this CLARKE Battery booster / charger which is suitable
More informationD&D Motor Systems, Inc.
D&D Motor Systems, Inc. Programmable Regen Controller Manual & Schematics BE ADVISED, D&D Motor Systems, Inc. does not design and manufacture controllers. We provide them as an extension to our existing
More informationATevo SERIES BATTERY CHARGER
PRODUCT OVERVIEW NEXT GENERATION NEW FEATURES: Interactive LCD display Intelligent self diagnostics NERC Compliant ATevo Battery Charger is the next generation SCR-based utility battery charger. The innovative
More informationBOOST POWER 1212 Product Description
BOOST POWER 1212 Product Description Contents 1 Introduction...4 2 General Description...4 2.1 Compatibility with standard Lead-Acid Batteries... 4 3 Battery Performance...5 3.1 Discharge Capability...
More informationEV Power - A-Series 8 Cell, 16 Cell and 24Cell Chargers Installation & Usage Instructions.
A-CHARGERS MANUAL 1.1 EV Power - A-Series 8 Cell, 16 Cell and 24Cell Chargers Installation & Usage Instructions. A-Series Charger Features - Simple to install and use, microprocessor control. - LiFePO4
More informationAT EVO SERIES BATTERY CHARGER
STANDARD FEATURES 5 YEAR WARRANTY EVO AT Series Battery Charger is HindlePower s next generation SCR-based utility battery charger. This evolutionary product is revolutionary in its design and operation
More informationLiFePO4 Battery(Bluetooth) Specification
LiFePO4 Battery(Bluetooth) Specification Model: TB-BL12100F-M110D SHENZHEN TOPBAND NEW ENERGY CO.,LTD Address: Topband Industrial Park,Liyuan Industrial Zone,Shiyan,Bao'an,Shenzhen, China,518108. Web:ww.topband.com.cn
More informationObserve all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.
Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary
More informationPowerCommand. ModLon II Gateway. Specifications. ModBus LON Converter
PowerCommand ModLon II Gateway ModBus LON Converter Description The PowerCommand ModLon II Gateway is used to interface PowerCommand networks to devices and systems that communicate in Modbus communication
More informationRUTLAND HRDi CHARGE REGULATOR INSTALLATION AND OPERATION
RUTLAND HRDi CHARGE REGULATOR INSTALLATION AND OPERATION Introduction Congratulations and thank you for purchasing Marlec s HRDi Charge Regulator. This is the latest technology for charge regulation of
More informationLiFePO4 Battery Specification
LiFePO4 Battery Specification Model: JARO BT9.12 Jarocells Address: :Architect Dudoklaan 23, 2552 MV Rijswijk, The Netherlands Registered B. ten Berge Customer Checked R. Hurkmans Customer Model Approved
More informationSP6. Automatic Battery Charger. Model
Model SP6 Automatic Battery Charger OWNERS MANUAL PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the charger safely and effectively. Please read and follow
More informationLiFePO4 Battery(Bluetooth) Specification
LiFePO4 Battery(Bluetooth) Specification Model: JAROCELL BT12.100 Jarocells Address: :Architect Dudoklaan 23, 2552 MV Den Haag, The Netherlands Registered B. ten Berge Customer Checked R. Hurkmans Customer
More information3500W Solar Battery Charger Maximum Power Point Tracker
Page 1 of 8 This revolutionary maximum power point tracker solar charger was designed using the technology that won GSL Electronics the prestigious EDN Innovation Awards 08 and 09 and the Greentech Consensus
More informationl The Battery Tester is designed for measuring the l AC four-terminal method to measure the internal
Certificate of Calibration We hereby certify that this product has been calibrated and found to be in accordance with the applicable SPECIFICATIONS and STANDARDS. Accuracies of the standard equipment used
More informationPWM Charge Controller with LCD Display 30A. User Manual
PWM Charge Controller with LCD Display 30A User Manual 1 Product Features 1. 12V/ 24 V system voltages are automatically recognized. 2. Charging program options for sealed, GEL and flooded lead-acid batteries
More informationModbus Register Map:Galaxy VM (3: kVA 400/480V)
Modbus Register Map:Galaxy VM (3:3 50-225kVA 400/480V) Part number: 990-9692 Notes:. 6-bit registers are transmitted MSB first (i.e. big-endian). 2. INT32 and UINT32 are most-significant word in n+0, least
More informationArt. No. EC-315. Art. No. EC-330. Art. No. EC-340 SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2
SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2 DESCRIPTION AND FEATURES... 3 CHARGING STAGES... 4 Art. No. EC-315 Art. No. EC-330 Art. No. EC-340 PROTECTIONS... 5 INSTALLATION...
More informationLiFePO4 Battery(Bluetooth) Specification
LiFePO4 Battery(Bluetooth) Specification Model: TB-BL1250F-S110A SHENZHEN TOPBAND NEW ENERGY CO.,LTD Address: Topband Industrial Park,Liyuan Industrial Zone,Shiyan,Bao'an,Shenzhen, China,518108. Web:ww.topband.com.cn
More information