OPERATION AND MAINTENANCE MANUAL FOR RELEASE MECHANISM
|
|
- Susanna Porter
- 5 years ago
- Views:
Transcription
1 OPERATION AND MAINTENANCE MANUAL FOR RELEASE MECHANISM (MODEL : TALONⅡ 4.0, TALONⅡ 6.0, TALON 9.0 ) Revision 10 / September 23, 2014 (Document No. : H ) HLB C o., L t d , Dangwol-ro, Onsan-Eup, Ulju-Gun, Ulsan, Korea Tel: / Fax: / Web Site: 1
2 Identification symbols for levels of risk, used in this manual: Warning Highest level of risk. Incorrect or incomplete operation may result in death or serious injury. Caution Second highest level of risk. Incorrect or incomplete operation may result in equipment damage. Less critical mandatory instructions. Mandatory Important note that should be emphasized. Note Never A prohibited action. Incorrect action may result in death of occupants. 2
3 TABLE OF CONTENTS 1. General 2. Release gear operation for launching and recovery 2.1 Method of checking proper closure of release hooks 2.2 Launching operation 2.3 Recovery operation 3. On-load/off-load release gear system 3.1 General 3.2 Fore and aft hook units 3.3 Release handle unit 3.4 Hydrostatic interlock unit 4. Assembly and spare parts 4.1 Hook assembly 4.2 Release handle unit 4.3 Hydrostatic interlock unit 4.4 Cable specification 4.5 Torque specifications 5. Inspection & maintenance 5.1 Guideline for periodic inspection and maintenance by crew members 5.2 Guideline for servicing, periodic inspection by certified service engineer 5.3 Preparing release gear for inspection and maintenance 5.4 Inspection and maintenance plan 3
4 1. General The lifeboats are stored on the boat davits on both sides of the ship. In case of emergency, the crew can board the lifeboat and escaped with the lifeboat directly from its stowage position. The launching appliance consists of a boat davit (davit arm, frame, platform, falls, suspension block, and gripes/lashing device) and a boat winch (reduction gears, hand brake and centrifugal brake). Swinging out and lowering of the lifeboat can be controlled both from the inside of the lifeboat and at the ship s deck. The lowering speed of the lifeboat can be controlled by operating the remote control wire inside the lifeboat or by operating the remote control lever on the ship s deck. Moreover, it is possible to suspend the lowering operation of the lifeboat at any height. Recovery of the lifeboat is performed by operating the boat winch with the push-button switch box. When the davit arm reaches a prescribed position, the boat winch is automatically stopped by the limit switch. After the activation of the limit switch, the boat winch is operated manually to wind up the lifeboat to its stowage position. The boat winch is provided with a safety device to prevent the reverse operation of the manual handle. The lifeboat is equipped with on-load/off-load release gear which complies with the requirements of the IMO Life-Saving Appliance (LSA) Code. The release gear system is equipped with a hydrostatic interlock system so that it will normally not release the hooks until the boat is waterborne. To avoid possible injury or death, read this manual carefully before using the boat davit, the boat winch, and the on-load/off-load release gear. Note Operational tests with the master link used by the manufacturers of the launching appliances should be carried out also before the particular combination of lifeboat/ release hook and launching appliance can be accepted. 4
5 1.1 General specification Model Hook SWL (safe working load) Hanging off pendents (same as pendent lug) Operating force of Release handle TALONⅡ 4.0 4TON 2.5TON Max. 25kgf TALONⅡ 6.0 6TON 3TON Max. 25kgf TALON 9.0 9TON 4.8TON Max. 30kgf Note Some sketches in the manual may not correspond exactly to the lifeboat-type described in the manual. The principles and procedures are, however, correct. 5
6 1.2 Recommended Davit Falls Master Link (Ring Type) Figure Ring Type Master Link TALONⅡ 4.0 TALONⅡ 6.0 TALON 9.0 SWL Min. 4 TON Min. 6 TON Min. 9 TON A 28~29 mm 32 ~ 34 mm B 85 mm 115 mm C 79 mm 155 mm Use the only our supplies. D 230 mm 263 mm E 0~43 mm 0~32 mm 6
7 1.3 Recommended Davit Falls Master Link (Plate Type) Figure Plate Type Master Link TALONⅡ 4.0 TALONⅡ 6.0 TALON 9.0 SWL Min. 4 TON Min. 6 TON Min. 9 TON A 28 mm 32 mm B 28 mm 32 mm C R 42.5 mm R 57.5 mm Use the only our supplies. D 80 mm 85 mm E 0~28 mm 0~32 mm Section A-A 7
8 1. Check points during the operation of Lifeboat & Davit A) Check the hook indicator B) Check the condition of connection parts between lifeboat hook and davit C) During davit test, do not onboard of the lifeboat. D) Do not carry out tests under the windy & heavy sea. 2. Do not lower the lifeboat on the water during the davit test. (The lifeboat should be in on-load condition) 3. If the davit link is in abnormal position when the lifeboat is lifted up, release the load on hooks, make the davit link to be in normal position and lift the lifeboat.. 4. Even if the davit link is detached from the hook, do not lift the lifeboat with only one release hook. Caution Normal position ex) Abnormal position 8
9 2. Release gear operation for launching and recovery 2.1 Method of checking proper closure of release hooks Safe use and operation of lifeboats during drills and inspection and maintenance is dependent on knowing that the release gear is properly reset. Never Never enter lifeboat without ensuring complete closure of release hooks. Incomplete resetting of the release hooks can cause the lifeboat to drop resulting in death Purpose of on-load release. The IMO LSA Code requires, among other things, that the lifeboat be fitted with on-load release capability which will release the lifeboat with a load on the hooks. The release mechanism shall be so designed that crew members in the lifeboat can clearly observe when the release mechanism is properly and completely reset and ready for lifting.... On-load release is needed for launching when there is a current, when the ship is making way, or potentially if there are waves which cause the hydrostatic interlock to only release intermittently. On-load release also allows an empty or fully loaded boat to drop from any height, which can kill or seriously injure the occupants. Therefore it is critical to know that the release gear is properly reset and the release handle secured. 9
10 2.1.3 Ensuring release hook closure. The first thing to check whenever entering the lifeboat when it is (or will be) supported by the falls is properly reset as follows: No. Operation Guide Schematic Diagram 1 Check that the indicators are in the green zone (locked position) on each hook side plate <One side-indicator1> <Activity on the ship> <The opposite side-indicator2> 2 Check that the hook safety pin not inserted into side plate. <Activity on the ship> 10
11 3 Check that the release handle is in the closed (locked) position and safety pin is installed. Release handle reset Indicator in Green zone <Activity in the lifeboat> Safety pin inserted 4 Ensure the hydrostatic indicator is in the Green zone. <Activity in the lifeboat> 11
12 2.2 Launching operation Releasing procedure A flow chart of the off-load and on-load releasing procedure is shown in the following figure. Release procedure OFF LOAD RELEASE (See paragraph 2.2.2) ON LOAD RELEASE (See paragraph 2.2.3) (1) Confirm that lifeboat is waterborne. (1) Pull out the safety pin on the release handle. (2 ) Pull out the safety pin on the release handle. WARNING! Operate the release handle only upon confirmation of safety by the officer in charge! Release of the lifeboat from a height can cause injury or death (2) Remove the hydrostatic interlock cover. (3) Lift up hydrostatic interlock lever and hold it. (3) Lift up the release handle and pull down by one action. (4) Lift up the release handle and pull down by one action. Release operation completed. 12
13 2.2.2 Off-load release This operation is the normal method of launch and release is conducted when the lifeboat is fully waterborne. Confirm the following before the operation : The lifeboat is fully waterborne The engine is started. Caution All crew are in their seats with their seatbelts fastened. No Operation Guide Schematic Diagram 1 Confirm that the lifeboat is waterborne. <Activity in the lifeboat> 2 Pull out the safety pin on the release handle. <Activity in the lifeboat> safety pin 3 Lift up the release handle and Pull to the fully open position by one action. <Activity in the lifeboat> Note In a case where the hook is not released by the above operations, confirm condition of each hook and whether the boat is waterborne or not. Even though the hooks cannot be released by the off-load release operation described above, on-load release procedure, described in the following pages, is possible. 13
14 2.2.3 On-load release operation procedure. Emergency Release (include hydrostatic interlock unit override procedure) This procedure must only be used under extreme emergency conditions with the lifeboat 1 meter (maximum) within of water. Pay due precautions and conduct the on-load release operation in Warning accordance with orders of the officer in charge. Operation of the release handle upon insufficient confirmation of safety may result in death or injury due to dropping the lifeboat in the water from a height. Confirm the following before the operation : The lifeboat is not fully waterborne The engine is started. Caution All crew are in their seats with their seatbelts fastened. Before this on-load release operation, prior action below should be done. Caution 14
15 No. Operation Guide Schematic Diagram 1 Confirm that the lifeboat is as close as possible to the water surface, but that the hydrostatic interlock is not triggered. <Activity in the lifeboat> 2 Pull out the safety pin on the release handle. <Activity in the lifeboat> Pull out the safety pin 3 Remove the hydrostatic interlock cover. <Activity in the lifeboat> 4 Lift up hydrostatic interlock lever and hold it. <Activity in the lifeboat> 5 Pull the release handle to the fully open position by one action. <Activity in the lifeboat> 15
16 2.2.4 Training/drill/maintenance release operation This operation is conducted when the lifeboat can be used only during training /drill/ maintenance operation. Before operation the davit, insert safety pin to fore and aft hooks. Caution A flow chart of the off-load and on-load releasing procedure is shown in the following figure. Release procedure OFF LOAD RELEASE (See paragraph 2.2.4) ON LOAD RELEASE (See paragraph 2.2.5) (1) Before operation the davit, insert safety pin to fore and aft hooks. (1) Before operation the davit, insert safety pin to fore and aft hooks. (2) Confirm that lifeboat is waterborne. (2) Confirm that the lifeboat is as close as possible to the water surface, but that the hydrostatic interlock is not triggered. (3) Pull out the fore and aft hook safety pins. (3) Pull out the fore and aft hook safety pins. (4) Pull out the safety pin on the release handle. (4) Pull out the safety pin on the release handle. WARNING! Operate the release handle only upon confirmation of safety by the officer in charge! Release of the lifeboat from a height can cause injury or death (5) Open the release handle cover-side plate. (6) Lift up hydrostatic interlock lever and hold it. (5) Lift up the release handle and pull down by one action. (7) Lift up the release handle and pull down by one action. Release operation completed. 16
17 Off- load release (Training/drill/maintenance release operation) Confirm the following before the operation : The lifeboat is fully waterborne The engine is started. Caution All crew are in their seats with their seatbelts fastened. No. Operation Guide Schematic Diagram 1 Before operation the davit, insert safety pin to fore and aft hooks. <Activity on the ship >, <Activity in the lifeboat> hook safety pin 2 Confirm that the lifeboat is waterborne. <Activity in the lifeboat> 3 Pull out the fore and aft hook safety pins. <Activity in the lifeboat> hook safety pin 4 Pull out the safety pin on the release handle. <Activity in the lifeboat> 5 Lift up the release handle and pull to the fully open position by one action. <Activity in the lifeboat> 17
18 On- load release (Training/drill/maintenance release operation) This procedure must only be used under extreme emergency conditions with the lifeboat 1 meter (maximum) within of water. Pay due precautions and conduct the on-load release operation in Warning accordance with orders of the officer in charge. Operation of the release handle upon insufficient confirmation of safety may result in death or injury due to dropping the lifeboat in the water from a height. Confirm the following before the operation : The lifeboat is not fully waterborne The engine is started. Caution All crew are in their seats with their seatbelts fastened. Before this on-load release operation, prior action below should be done. Caution Latch of the interlock cover should be unlocked using tools. - Customer can use the spanner in the engine tool box stored in the inventory box of life boat to unlock the latch. - Spanner : 10mm 18
19 No. Operation Guide Schematic Diagram 1 Before operation the davit, insert safety pin to fore and aft hooks. <Activity on the ship >, <Activity in the lifeboat> hook safety pin 2 Confirm that the lifeboat is as close as possible to the water surface, but that the hydrostatic interlock is not triggered. <Activity in the lifeboat> 3 Pull out the fore and aft hook safety pins. <Activity in the lifeboat> hook safety pin 4 Pull out the safety pin on the release lever. <Activity in the lifeboat> Pull out the safety pin 5 Open the release handle cover-side plate. <Activity in the lifeboat> 19
20 6 Lift up hydrostatic interlock lever and hold it. <Activity in the lifeboat> 7 Lift up the release handle and Pull to the fully open position by one action. <Activity in the lifeboat> 20
21 2.3 Recovery operation Outline of the resetting procedures is shown in the following figure. Warning Incomplete resetting may result in death or serious injury due to dropping of the lifeboat in the water from a height. Resetting Procedure Hook Release handle One person each to be stationed for the fore and aft hooks. One person to be arranged. (1) Ensure fore and aft hooks are rotated into reset position. (2) Insert the fore and aft hooks safety pin. (3) Push release handle back in locked position. (5) Confirm the fore and aft hooks are in the locking position (green zone). (4) Insert the release handle safety pin. (6) Hook the master links onto the forward and aft release hooks by pushing the link past the Self locker on the release hooks, observe the Self locker are closed. (8) Hoist the lifeboat just clear of the water and stop hoisting. (9) Check to ensure the hook locking device(safety pin) can be rotated. (10) Stow lifeboat. (11) Once all checks are complete, crew persons are instructed to remove the hook safety pins and place them in their stored location. 21
22 2.3.1 Resetting procedure of release hook The resetting procedure is to be in accordance with the following steps. NOTE At least three people are required for the resetting of the hooks. No. Operation Guide Schematic Diagram hook Ensure fore and aft hooks are rotated into reset position. 1 Ensure the movement is freely. Check whether the hook hole and side plate hole for safety pin are exactly aligned. Hook hole <Activity in the lifeboat> Side plate hole hook safety pin 2 Insert the safety pin in the side plate hole on each hook assembly. <Activity in the lifeboat> 3 Push release handle back in locked position. 22
23 4 Make sure that the release handle is in the closed (locked) position and insert the safety pin. If the release handle is not in its closed (locked) position, it is not possible to insert the safety pin. 5 Confirm the fore and aft hooks are in the locking position (green zone). Cam position check. <One side-indicator1> <The opposite side-indicator2> 6 Hook the master links onto the forward and aft release hooks by pushing the link past the Self locker on the release hooks, observe the Self locker are closed. Check the Self locker closed position. Hoist the lifeboat just clear of the water and stop hoisting. Master link Self locker closed position 7 Confirm that the fore and aft hooks are properly connected. Maximum 1 meter 8 <Activity on the ship> and <Activity in the lifeboat> The hydrostatic interlock indicator went all the way to the Green zone in the locked position. Sea level Indicator in Green zone Check the indicator. <Activity in the lifeboat> 23
24 Check to ensure the hook locking device(safety pin) can be rotated. 9 Check the hook safety pin Hook safety pin <Activity in the lifeboat> Stow lifeboat. 10 <Activity on the ship> <Activity in the lifeboat> 11 Once all checks are complete, crew persons are instructed to remove the hook safety pins and place them in their stored location. Stored location If the hook safety pin cannot be rotated, then the lifeboat must be NOTE lowered to the water. Once the load is off the hooks, the release control unit must be open and reset again. Hoist the lifeboat just clear of the water and repeat step 9. If the hook safety pin still cannot be rotated, leave the hook safety pin in and hoist all the way home. Service is required immediately! 24
25 3. On-load/off-load release gear system TALON 3.1 General This section describes the details of the release gear system. Read this section carefully for safe operation. This release gear system consists of fore and aft hooks, a release handle near the steering console, a hydrostatic unit and the associated cables (see Fig ). The releasing operation of the hooks is conducted at the release handle near the steering console through the control cables terminating at the fore and aft hooks. The interlock system including the hydrostatic interlock unit is provided to prevent the release of the hooks when the boat is not waterborne. The system also has an on-load release function which makes it possible to over-ride the interlock by the hydrostatic unit. Incorrect on-load release operation may cause fatalities and due precautions should be taken for this operation. Fig Schematic of release gear system 25
26 3.2 Fore and aft hook units Structure and parts names The structure and parts names of the fore and aft hooks are shown in Figures and The fore and aft hooks are generally identical except for the direction of installation. Fig Perspective of the hook assembly Fig Internal view of the hook assembly 26
27 3.2.2 Releasing When the release handle near the steering console is pulled, the cam is turned by the control cable. And stopper is turned automatically by the weight. And the hook is turned and released. (see figure ) Fig Release principle of the hook unit Resetting To ensure the proper resetting of the fore and aft hooks, the procedures described in paragraph should be followed. First return the fore and aft hooks to the close position and rotate the handle to handle close position. Automatically the fore and aft cams, stopper also return to the closed position. Fig Reset principle of the hook unit 27
28 3.3 Release handle unit Structure and parts names The structure and parts names of the release handle are shown in figures and Fig Perspective of the release handle unit Fig Internal view of the release handle unit 28
29 3.3.2 Operation When the lifeboat is fully waterborne, the lifeboat can be released by removing the safety pin and then pulling the release handle fully and quickly to the open position (off-load release). The lifeboat can also be released by the same operation of the release handle even though the lifeboat is not fully waterborne, by opening the interlock cover and lifting up the interlock lever. This over-rides the interlock function of the hydrostatic interlock unit (on-load release) are shown in figures Fig Operation procedure of the release handle 29
30 3.4 Hydrostatic interlock unit Structure and parts name Structure and parts names of the hydrostatic interlock unit are shown in figures Interlock cable (to the hydrostatic interlock lever of the release handle unit) Pressure of seawater Fig Perspective and Internal view of the hydrostatic interlock unit Operation When the lifeboat is fully waterborne, the hydrostatic interlock unit pushes up the interlock lever through the interlock cable by the water lifting the float and thus allowing the release handle to be operated. Contrary to this, operation of the release handle is not allowed by the hydrostatic interlock unit when the lifeboat is not fully waterborne and the interlock is shown in figures Fig Schematic diagram of the interlock 30
31 4. Assembly and spare parts The components of the release system will be delivered completely assembled. However, it is important to know the assembly procedure for all components. This section provides instructions for the hook assembly, release handle unit, and hydrostatic interlock unit. To order spare parts for the release system, please contact HLB Co., Ltd. Korea / Head Office #772, Daejung-Ri, Onsan-Eup, Ulju-Gun, Ulsan, Korea Tel: ~2 Fax: service@hdboat.com Singapore Office HLB Singapore Pte. Ltd. Tel: ~4 Fax: info@hlbsingapore.com Web: Shanghai Branch Office. Room1107, No.2277, Zuchongzhi Road, Zhangjiang Hi-Tech park, Pudong New District, Shanghai , China Tel: Fax: info@hlbshanghai.com 31
32 4.1 Hook assembly Figure Exploded view of hook assembly 32
33 - Hook assembly spare parts index <TALONⅡ 4.0> NO PART NO PART NAME Q TY REMARKS 1 H SIDE PLATE-LH 1 2 H SIDE PLATE-RH 1 3 H SUPPORT-PIN HOOK LH 1 4 H SUPPORT-PIN HOOK RH 1 5 H SUPPORT-CAM 1 6 H BACK PLATE-OUTSIDE 1 7 H Alternative HOOK H H PIN-HOOK 1 9 H BUSH-HOOK PIN 1 10 H WASHER-HOOK 2 11 H STOPPER 1 12 H PIN-STOPPER 1 13 H BUSH-STOPPER H CAM 1 16 H BUSH-CAM LH 1 17 H BUSH-CAM RH 1 18 H INDICATOR-CAM 1 19 H LEVER-CAM 1 20 H SPACER-CAM 1 21 H COVER-CAM ASSY 1 22 H CLEVIS-HOOK 1 23 H PENDENT LUG 1 24 H PIN-PENDENT LUG 1 25 H BUSH-PENDENT LUG H BLOCK 1 28 H SELF LOCKER 1 29 H SUPPORT-SELF LOCKER 2 30 H BOLT-SELF LOCKER 4 31 H SIGN-INDICATOR-LH 1 32 H SIGN-INDICATOR-RH 1 33 H SAFETY-PIN ASSY 1 34 H CLAM-HOOK CABLE 1 35 H BACK PLATE-INSIDE 1 36 H WARNING PLATE 2 33
34 37 H NAME PLATE HEXAGON HEAD BOLTS 1 M12X1.75X HEXAGON HEAD BOLTS 1 M12X1.75X HEXAGON HEAD BOLTS 1 M8X1.25X HEXAGON HEAD BOLTS 2 M10X1.5X HEXAGON SOCKET HEAD CAP SCREWS 3 M5X0.8X HEXAGON SOCKET BUTTON HEAD SCREWS 4 M5X0.8X HEXAGON SOCKET HEAD CAP SCREWS 4 M8X1.25X NYLON NUT (HOOK) 1 M20X NYLON NUT (PENDENT-LUG) 1 M16X NYLON NUT (BLOCK) 2 M12x NYLON NUT (STOPPER) 1 M16X NYLON NUT (CAM) 1 M20X NYLON NUT (CAM) 1 M24X NYLON NUT 2 M10X TOOTHED LOCK WASHERS 1 Ø O-RING 1 P GREASE NIPPLES 4 A-PT 1/8 34
35 <TALONⅡ 6.0> NO PART NO PART NAME Q TY REMARKS 1 H SIDE PLATE-LH 1 2 H SIDE PLATE-RH 1 3 H SUPPORT-PIN HOOK LH 1 4 H SUPPORT-PIN HOOK RH 1 5 H SUPPORT-CAM 1 6 H BACK PLATE-OUTSIDE 1 7 H Alternative HOOK H H PIN-HOOK 1 9 H BUSH-HOOK PIN 1 10 H WASHER-HOOK 2 11 H STOPPER 1 12 H PIN-STOPPER 1 13 H BUSH-STOPPER 1 14 H WASHER-STOPPER 2 15 H CAM 1 16 H BUSH-CAM LH 1 17 H BUSH-CAM RH 1 18 H INDICATOR-CAM 1 19 H LEVER-CAM 1 20 H SPACER-CAM 1 21 H COVER-CAM 1 22 H CLEVIS-HOOK 1 23 H PENDENT LUG 1 24 H PIN-PENDENT LUG 1 25 H BUSH-PENDENT LUG H BLOCK 1 28 H SELF LOCKER 1 29 H SUPPORT-SELF LOCKER 2 30 H BOLT-SELF LOCKER 4 31 H SIGN-INDICATOR-LH 1 32 H SIGN-INDICATOR-RH 1 33 H SAFETY-PIN ASSY 1 34 H CLAM-HOOK CABLE 1 35 H BACK PLATE-INSIDE 1 36 H WARNING PLATE 2 37 H NAME PLATE 1 35
36 HEXAGON HEAD BOLTS 1 M16X2.0X HEXAGON HEAD BOLTS 1 M16X2.0X HEXAGON HEAD BOLTS 1 M8X1.25X HEXAGON HEAD BOLTS 2 M10X1.5X HEXAGON SOCKET HEAD CAP SCREWS 3 M6X1.0X HEXAGON SOCKET BUTTON HEAD SCREWS 4 M5X0.8X HEXAGON SOCKET COUNTERSUNK HEAD SCREWS 4 M10X1.5X NYLON NUT (HOOK) 1 M24X NYLON NUT (PENDENT-LUG) 1 M20X NYLON NUT (BLOCK) 2 M16X NYLON NUT (STOPPER,CAM) 2 M20X NYLON NUT (CAM) 1 M24x NYLON NUT 2 M10X TOOTHED LOCK WASHERS 1 Ø O-RING 1 P GREASE NIPPLES 4 A-PT 1/8 36
37 <TALON 9.0> NO PART NO PART NAME Q TY REMARKS 1 H SIDE PLATE-LH 1 2 H SIDE PLATE-RH 1 3 H SUPPORT-PIN HOOK LH 1 4 H SUPPORT-PIN HOOK RH 1 5 H SUPPORT-CAM 1 H SIDE PLATE ASSY 6 H BACK PLATE-OUTSIDE 1 7 H HOOK 1 8 H PIN-HOOK 1 9 H BUSH-HOOK PIN 1 10 H WASHER-HOOK 2 11 H STOPPER 1 12 H PIN-STOPPER 1 13 H BUSH-STOPPER 1 14 H WASHER-STOPPER 2 15 H CAM 1 16 H BUSH-CAM LH 1 17 H BUSH-CAM RH 1 18 H INDICATOR-CAM 1 19 H LEVER-CAM 1 20 H SPACER-CAM 1 21 H COVER-CAM ASSY 1 22 H CLEVIS-HOOK 1 23 H PENDENT LUG 1 24 H PIN-PENDENT LUG 1 25 H BUSH-PENDENT LUG 1 26 H WASHER-PENDENT LUG 2 27 H BLOCK 1 28 H SELF LOCKER 1 29 H SUPPORT-SELF LOCKER 2 30 H BOLT-SELF LOCKER 4 31 H SIGN-INDICATOR-LH 1 32 H SIGN-INDICATOR-RH 1 33 H SAFETY-PIN ASSY 1 34 H CLAM-HOOK CABLE 1 35 H BACK PLATE-INSIDE 1 36 H WARNING PLATE 2 37 H NAME PLATE 1 37
38 38 H SUPPORT-PENDENT LUG HEXAGON HEAD BOLTS 1 M20X2.5X HEXAGON HEAD BOLTS 1 M20X2.5X HEXAGON HEAD BOLTS 1 M8X1.25X HEXAGON HEAD BOLTS 2 M10X1.5X HEXAGON SOCKET HEAD CAP SCREWS 3 M6X1.0X HEXAGON SOCKET BUTTON HEAD SCREWS 4 M5X0.8X HEXAGON SOCKET COUNTERSUNK HEAD SCREWS 4 M10X1.5X NYLON NUT 2 M24x NYLON NUT 5 M20x NYLON NUT 2 M10X TOOTHED LOCK WASHERS 1 Ø O-RING 1 P GREASE NIPPLES 2 A-PT 1/8 38
39 - Assembly Follow the procedure below for the assembly of the release hook. 1. Side plate assembly Place the side plate assembly as below(figure 4.1.2). Side plate assembly contain side plate-lh, side plate-rh, support-pin hook LH, support-pin hook RH, support-cam and back plate-outside (Figure 4.1.1) and that parts are welded. Figure Side plate assembly with position of specified parts 39
40 2. Hook group When assemble the hook group, Please see the Figure 4.1.2, and Inner parts of side plates(1, 2) : Washer-hook(10, 2EA), Bush-hook pin(9), Hook(7) - Outside parts of side plate-rh(2) : Pin-hook(8), Grease nipple(51) - Outside part of side plate-lh(1) : Nylon nut(46) Figure Hook group Figure Hook group with side plates 40
41 3. Stopper group When assemble the stopper group, Please see the Figure 4.1.2, and Inner parts of side plates(1, 2) : Bush-stopper(13), Washer-stopper(14, 2EA), Stopper(11) - Outside parts of side plate-rh(2) : Pin-stopper(12), Grease nipple(51) - Outside part of side plate-lh(1) : Nylon nut(47) Figure Stopper group Figure Stopper group with side plates 41
42 4. Cam group When assemble the cam group, Please see the Figure 4.1.2, and Inner part of side plates(1, 2) : Cam(15) - Outside parts of side plate-rh(2) : Nylon nut(47), Lever-cam(19), Spacer-cam(20), Bush-cam RH(17), O-ring(50) - Connection parts of Lever-cam(19) : Bolt(41), Washer(49), Clevis-hook(22) - Outside parts of side plate-lh(1) : Bush-cam LH(16), Indicator-cam(18), Nylon nut(47) Figure Cam group Figure Cam group with side plates 42
43 5. Clamp-hook cable group When assemble the clamp-hook cable group, Please see the Figure 4.1.2, and Inner part of side plates(1, 2) : Nylon nut(48, 2EA) - Outside parts of side plate-rh(2) : Clamp-hook cable(34), Bolt(42, 2EA) Figure Clamp-hook cable group Figure clamp-hook cable group with side plates 43
44 6. Pendent lug group When assemble the pendent lug group, Please see the Figure 4.1.2, and Inner parts of side plates(1, 2) : Washer-pendent lug(26, 2EA), Bush-pendent lug(25), Pendent lug(23) - Outside part of side plate-rh(2) : Pin-pendent lug(24) - Outside part of side plate-lh(1) : Support-pendent lug(38), Nylon nut(46) Figure Pendent lug group Figure pendent lug group with side plates 44
45 7. Block, safety-pin assy group When assemble the Block, safety-pin assy group, Please see the Figure 4.1.2, and Inner part of side plates(1, 2) : Block(27) - Outside parts of side plate-rh(2) : Bolt(39), Bolt(40) - Outside parts of side plate-lh(1) : Safety-pin assy(33), Nylon nut(47, 2EA) Figure Block, safety-pin assy group Figure Block, safety pin assy group with side plates 45
46 8. Cover-cam assy, sign-indicator LH,RH group When assemble cover-cam assy, sign-indicator LH,RH group, Please see the Figure 4.1.2, and Outside parts of side plate-rh(2) : Sign-indicator-RH(32), M5 screw(44, 2EA), Cover-cam assy(21), M6 screw(43, 3EA) - Put the silicon contact surface of side plate-rh(2) and cover-cam assy(21) TALON II 4.0, 6.0 : Use silicone for PC. (Polycarbonate) Caution - Outside parts of side plate-lh(1) : Sign-indicator-LH(31), Screw(44, 2EA) Figure Cover-cam assy, sign-indicator LH,RH group Figure Cover-cam assy, sign-indicator-lh,rh group with side plates 46
47 9. Self-locker, support-self locker group When assemble the Self-locker, support-self locker group, Please see the Figure 4.1.2, and Outside parts of side plates(1, 2) : Self locker(28), Bolt-self locker(30) - Outside parts of side plate-rh(2) : Support-self locker(29), Screw(45, 2EA) - Outside parts of side plate-lh(1) : Support-self locker(29), Screw(45, 2EA) Figure Self-locker, support-self locker group Figure Self-locker, support-self locker group with side plates 47
48 4.2 Release handle unit Figure Exploded view of Release handle unit 48
49 - Release handle unit spare parts index NO PART NO PART NAME Q TY REMARKS 1 H PLATE-SIDE RH 1 2 H PLATE-SIDE LH 1 3 H GLASS 1 4 H RELEASE HANDLE ASSY 1 5 H LOCKER ASSY 1 6 H COVER-SIDE PLATE 1 7 H SAFETY PIN ASSY 1 8 H SUPPORT-HYDRO CABLE 1 9 H SUPPORT-HOOK CABLE 2 10 H CLAMP-HOOK CABLE 2 11 H PLATE-RELEASE HANDLE 1 12 H SPACER H SPACER H SPRING-LOCKER BOLT 4 M6X1.0X BOLT 8 M8X1.25X BOLT 3 M12X1.75X BOLT 2 M8X1.25X BOLT 1 M16X2.0X SPRING WASHER 10 M PLAIN WASHER 1 M PLAIN WASHER 14 M NUT-NYLON 10 M NUT-NYLON 5 M NUT-NYLON 1 M BOLT 2 M12X1.75X PLAIN-WASHER 4 M6 49
50 4.3 Hydrostatic interlock unit Figure Exploded view of Hydrostatic interlock unit 50
51 - Hydrostatic interlock unit spare parts index NO PART NO PART NAME Q TY Q TY REMARKS H Alternative HYDRO ASS Y H H COVER-HYDRO UPPER H H COVER-HYDRO LOWER H H PLANGE-PLATE H PLATE-DIAPHRAGM H DIAPHRAGM H PLATE-HYDRO H BRKT-FITTINGS 1 8 H FITTINGS-ONE TOUCH 2 Ø12, PT1/4 9 H HOSE-AIR 1 1 Ø12X500mm FLAT HEADED BOLT 4 4 M4X0.7X HEXAGON HEAD BOLTS 8 M8X1.25X20 10 M8X1.25X HEXAGON HEAD BOLTS 6 6 M8X1.25X SPRING WASHER PLAIN WASHER 10 Ø SPRING WASHER 6 6 Ø HEXAGON NUTS WITH FLANGE 10 M8X H BAND 2 Ø12 51
52 4.4 Cable specification Push / Pull cables requirements Type Hook cable Hydrostatic interlock unit cable TALONⅡ4.0 TALONⅡ6.0 TALON 9.0 TALONⅡ4.0, 6.0 and TALON 9.0 Length Stroke / travel 100mm 25mm Threaded end type 5/16-24 UNF-2A M10 X 1.25 M5 X 0.8 Series / SWL 64C / 180kgf 64C / 180kgf 84C / 450kgf 31B / 50kgf - Length = Measured Length + 200mm - Minimum bending radius of TALON 9.0 hook cable : 150mm - Minimum bending radius of TALONⅡ 4.0, 6.0 hook cable : 125mm - Minimum bending radius of Hydrostatic interlock unit cable : 50mm Cable assembly length : Minimum 15mm Warning 4.5 Torque specifications BOLT SIZE TORQUE (N-m ) M4 5 M5 5 M6 10 M8 15 M10 30 M12 45~50 M16 50~60 M M
53 5. Inspection & Maintenance Lifeboats, launching appliances and release gear are required by SOLAS regulationⅢ/20 to be inspected weekly and monthly according to the instruction for on-board maintenance complying with the requirements of SOLAS regulation Ⅲ/ Guideline for periodic inspection and maintenance by crew members Weekly, monthly inspection and routine maintenance may be done by crew members under the direct supervision of a senior ship s officer General precautions During weekly, monthly inspection and routine maintenance by crew members - Please inform a senior ship s officer before starting any inspections and maintenances on the Lifeboat - Please make sure that the lifeboat is definitely secured to the davit. - The crew members should be well-acquainted with these guidelines before starting works. - Please open all hatches, doors and windows for ventilation - Do not operate the release mechanism and touch any part of release system before checking the safety precautions. - Do not operate the engine without permission Inspection and maintenance plan Release gear should be inspection and maintained weekly and monthly in accordance with the following tables which list the items to be checked, the method inspection, the procedures to be followed and the frequency at which the items are to be attended to. 53
54 5.2 Guideline for servicing, periodic inspection by certified service engineer All other inspections, servicing and repair except weekly, monthly inspection and routine maintenances mentioned above should be conducted by appropriately trained and certified service personnel of HLB Co., Ltd. Inspections and servicing will be conducted in accordance with the following tables by a valid HLB certified engineer. Caution All inspections, servicing and repair works for annual inspection are only allowed to be carried out by certified service engineers with a valid certificate as authorized service engineer for lifeboat. HLB Co., Ltd. has no responsibility for unauthorized works to the lifeboat system and avoid all guarantees. Defects found through annual inspection have to be solved and damaged parts to be fixed or replaced by authorized service engineer. 54
55 5.3 Preparing Release gear for inspection and maintenance To prepare the release gear for maintenance, refer to the following procedure: No. Operation Guide Schematic Diagram 1 Check that the indicators are in the green zone (locked position) on each hook side plate <One side-indicator1> <Activity on the ship> <The opposite side-indicator2> 55
56 2 Check that the locking device is inserted on each hook side plate <Activity on the ship> 3 Check that the release handle is in the closed (locked) position and safety pin is installed. <Activity in the lifeboat> 4 Connect the maintenance assembly to the forward and aft pendent lug or it can be done with the lifeboat in the warer. The maintenance assembly contain the wire, link and shackle <Activity in the lifeboat> 56
57 5.4 Inspection and maintenance plan Release gear system should be inspected and maintained in accordance with the following tables. The tables list the items to checked, the method of inspection, the procedures to be followed. Table Inspection and maintenance plan for Lifeboat release and retrieval system. Items Method Inspection procedure Release gear (hook assembly) Moving parts (Hook, Stopper, Cam, Pendent lug,) Cables (Hydro, Aft, Fwd) Grease nipple Hook and stopper Pin-hook, Pin-stopper and pin-pendent lug Cam Release handle unit Hydrostatic interlock unit Visual Visual Visual Visual Visual and Gauge Visual and Gauge Visual and Gauge Visual Visual - Confirm the release gear is closed position before any inspection of release gear system. - Remove any dirt, salts, dust on the release gear. - Check for any damage of release gear system - Ensure all bolts are secured. - Check the indicator in the locking position (locking position : green color) - Check the operation is smoothly when the lifeboat is fully waterborne condition or supported by the pendent lug. - Check for any damage - Check all cable end connectors. Replace as necessary. - Check the cable end fittings for signs of corrosions. Clean as needed - Remove any dirt on the grease nipple of hook pin - Add marine grease on the grease nipple of pin-hook,pin-stopper, pin-pendent lug and cam if needed A good quality marine grease should be used - When the lifeboat is in the water or disconnected from the davit, lift up the hook by hand and measure the contact surface. -Measure the contact surface between hook and stopper using the D2.6mm round gauge Note : If the D2.6 round gauge is inserted in the contact surface, replace pin-hook, pin-stopper and stopper (See Figure as below) - Check curvature of pin-hook, pin-stopper and pin-pendent lug against a flat edge. Note : If there is a curvature offset of 0.5mm from the original surface (See Figure as below) Maintenance plan W M 1Y 5Y X X X X X X X X X R X X X X X X X X - Check the contact surface of cam for wear marks where the stopper impacts the cam Note : If indentation is greater than 1mm, replace cam (See Figure as below) X X - Check for any damage - Ensure all components move freely. - Check the interlock indicator is closed position (closed position : green color) X X X X - Check the hydrostatic interlock unit control cable - Ensure all bolts are secured. - Check for any damage - Ensure all bolts are secured. X X X X X X 57
58 Required replace item Yearly 5-yearly Diaphragm Diaphragm, Cables(hydrostatic, Fwd, Aft) Figure Check the contact surface between hook and stopper using the D2.6mm round gauge 58
59 Figure Check the pin-hook, pin-stopper and pin-pendent lug Figure Check the cam 59
4. MAINTENANCE MANUAL
4. MAINTENANCE MANUAL 4.1 INTRODUCTION The maintenance program has been developed by ORIENTAL in accordance to our supplier s own maintenance program for each component. Conforming to this maintenance
More informationBefore equipment use, please read this operation manual carefully. Serial Number: Date Purchased:
Pushed & Geared Trolleys OPERATION MANUAL This operation manual is intended as an instruction manual for trained personnel who are in charge of installation, maintenance, repair etc. Before equipment use,
More informationNorsafe Project No.: TBA Norsafe Doc. No.: TSB-0013 Rev. Date: Rev. No: 1
MAXIMA-120 MKI Norsafe Project No.: TBA Norsafe Doc. No.: TSB-0013 Rev. Date: 15.09.2016 Rev. No: 1 Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com
More informationE-150 MKI - Single Pivot Gravity Davit
E-150 MKI - Single Pivot Gravity Davit Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0054 Rev. Date: 14.10.2016 Rev. No: 4 Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47
More informationTechnical specification for LH-230 Lifeboat Davit
Technical specification for LH-23 Lifeboat Davit Issued for information PGO GNI GNI REV.: DATE: Reason for Issue / Description: Norsafe Project No.: Project Title: Made By: Checked By: Project Approve
More informationLH-140 MKIII Lifeboat davit
LH-140 MKIII Lifeboat davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATIONS
More informationTechnical specification for NDA 40 NO Rescue Boat Davit
Technical specification for NDA 40 NO Rescue Boat Davit 1.06.014 Weight information added PGO ESO GNI 1 18.06.013 Re issued for construction PGO GNI GNI 0 Issued for construction PGO GNI GNI REV.: DATE:
More informationTechnical specification for NDC 40 NO Rescue Boat Davit
Technical specification for NDC 40 NO Rescue Boat Davit 8.06.203 Re issued for construction PGO GNI GNI 0 25.04.203 Issued for construction PGO GNI GNI REV.: DATE: Reason for Issue / Description: Project
More informationInstallation and Maintenance Manual MRW-01. Radial Winch 40.2 PT
MRW-01 Index Introduction Technical characteristics Weight Maximum working load Outline Installation Procedure 1 Procedure 2 Installation procedure Maintenance Washing Maintenance table Disassembly procedure
More information1 Planning Information
Rudder Centering Fork - Control Stop Replacement 1 Planning Information 1.1 Affected Aircraft Type: Model: Serial Number: Applicable Countries: CT CTLS 1.2 Concurrent Documents None 1.3 Reason F-08-10-21,
More informationWallace Tri-Adjustable Gantry Cranes Square Tube Assembly Instructions
Wallace Tri-Adjustable Gantry Cranes Square Tube Assembly Instructions For any additional information, Please call 1- S 1. Read and understand instructions before using this gantry. 2. Inspect gantry thoroughly
More informationWARNING. Electric Recovery Winch. General Safety Precautions
1 Electric Recovery Winch Thanks for purchasing a WINCH. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available
More informationNDSC-34 MKI - Rescue Boat Davit
NDSC-34 MKI - Rescue Boat Davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0048 Rev. Date: 14.11.2016 Rev. No: 3 Tel: +47 37 05 85 00 Fax: +47 37 05 85
More informationGeneral Instructions and Inspection Instructions for Crane
General Instructions General Instructions and Inspection Instructions for Crane Distributed by Ergonomic Partners Sales@ErgonomicPartners.com www.ergonomicpartners.com Tel: 314-884-8884 EN R_(EN)/1 --
More informationTitle: Lifting Operations Involving Crane or Gantry Offshore
PTW CHECKLIST - NO. 30 Title: Lifting Operations Involving Crane or Gantry Offshore Owner: Capability Coordinator Approver: Capability Coordinator Permit No.: Max Validity Period: 5 yrs Date: Latest Rev
More informationPerforma Winch 35.2 PTP
MRPW-01 Performa Winch 35.2 PTP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation procedure 5 Maintenance 7 Washing 7 Maintenance table
More informationINSTRUCTION MANUAL. Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps
INSTRUCTION MANUAL Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps IMPORTANT Please read this instruction manual before using these products. This manual contains
More informationInstallation and Maintenance Manual MRW-01. Radial Winch 20 ST
MRW-01 Index Introduction Technical characteristics Weight Maximum working load Outline Installation Procedure 1 Procedure 2 Installation procedure Positioning the self-tailing arm Maintenance Washing
More informationEMERGENCY TOWING ARRANGEMENTS HERMES" "HERACLES" & ZEUS INSTALLATION & MAINTENANCE
EMERGENCY TOWING ARRANGEMENTS HERMES" "HERACLES" & ZEUS 1) FOREWORD INSTALLATION & MAINTENANCE Emergency Towing Arrangements (ETA) "HERMES" & "HERACLES" are designed and produced by POSIDONIA SRL, Genoa
More informationY-fl'. MINISTRY OF TRANSPORT AND COMMUNICATIONS DEPARTMENT OF MARINE ADMINISTRATION
MINISTRY OF TRANSPORT AND COMMUNICATIONS DEPARTMENT OF MARINE ADMINISTRATION No-363/421, Corner of Merchant & Theinbyu Road, Botataung Township, Yangon, Myanmar E-mail : d gdma.mm@ gmail.com; dma.myan@smail.com
More informationInstallation and Maintenance Manual MRW-02. Radial Winch 20 ST
MRW-02 Index Introduction 3 Technical characteristics 3 Weights 3 Maximum working load 3 Outline 3 Installation 4 Procedure 1 5 Procedure 2 6 Installation procedure 8 Positioning the self-tailing arm 9
More informationMAINTENANCE MANUAL YAMADA AIR-OPERATED DIAPHRAGM PUMPS
Index MAINTENANCE MANUAL Doc. No. NDP033M-05 Issue 1998-6 Revised 2001-5 YAMADA AIR-OPERATED DIAPHRAGM PUMPS DP-F For your own safety, be sure to read these procedures carefully before performing maintenance
More informationPRODUCT MANUAL 12ST (V.4.0) 12ST FS (V.2.0.F) RON-WPM ST/12STFS-Rev.3
PRODUCT MANUAL 12ST (V.4.0) RON-WPM-710212-12ST/12STFS-Rev.3 12ST (V.4.0) EXPLODED VIEW ITEM No. 3-537551 ITEM. 3 MODEL 1 ST - PART No. 537551 3.1 p2 2 3.2 3 3.3 4 5 ITEM No. 3-537510 ITEM. 5 - PART No.
More informationMeaning of symbols Warning Caution. Prohibited. Required. Door Height. Door width. ±2 mm
Door Height Door width ±2 mm The closing speed of the soft closing type door may change due to Meaning of symbols Warning Caution Prohibited Required 1 2 Name Recessed roller soft closer Recessed roller
More informationPRODUCT MANUAL 46ST (V.5.0) 46ST FS (V.5.0.F) 50ST (V.2.0) 50ST FS (V.2.0.F) RON-WPM ST/46STFS/50ST/50STFS-Rev.3
PRODUCT MANUAL RON-WPM-710246-46ST/46STFS/50ST/50STFS-Rev.3 EXPLODED VIEW ITEM. 3 MODEL ST - PART No. 544521 ITEM. 3 MODEL ST FS - PART No. 544530 p2 ITEM. 12 - PART No. 775600/775650 ITEM. 13 - PART No.
More informationPerforma Winch 80.3 STP
MRPW-00 Performa Winch 80.3 STP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation Procedure 5 Positioning the self-tailing arm 8 Maintenance
More informationLineman s Hoist. Operating, Maintenance & Parts Manual. Follow all instructions and warnings for LMST680-2
Lineman s Hoist LMST0- Operating, Maintenance & Parts Manual Lineman s Hoist Follow all instructions and warnings for inspecting, maintaining and operating this hoist. The use of any hoist presents some
More informationOwner s (Operator s) Manual & Safety Instructions Manually Lever Operated Chain Hoist Model LX1B
Owner s (Operator s) Manual & Safety Instructions Manually Lever Operated Chain Hoist Model LX1B BULLETIN NO. LX-0804-CE-06 WARNING This equipment must not be installed, operated or maintained by any person
More informationToyota PRIUS Sway Bar, Rear Preparation
Toyota PRIUS 010- Sway Bar, Rear Preparation Part Number: PTR11-47010 Kit Contents: 1 1 PLUS Rear Sway Bar 1 Hardware Kit 3 Hardware Box Contents 1 1 Left - Sway Bar End Link with () M10 nuts 1 Right Sway
More informationButterfly Valve Type 58 (PDCPD)
Serial No. H-V074-E Butterfly Valve Type 58 (PDCPD) 700mm (28 ) User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General
More informationButterfly Valve Type 57P
Butterfly Valve Type 57P Contents Lever Type: 50-200 mm (2-8 ) Body Material: CPVC Gear Type: 50-200mm (2-8 ) Body Material: CPVC (1) Be sure to read the following warranty clauses of our product 1 (2)
More informationGES-21 MKI - Free Fall Lifeboat
GES-21 MKI - Free Fall Lifeboat Norsafe Project No.: TBA Norsafe Doc. No.: TSB-0071 Rev. Date: 30.09.2016 Rev. No: 2 Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85
More informationPerforma Winch 80.2 STP
MRPW-00 Performa Winch 80.2 STP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation Procedure 4 Disassembly Procedure 5 Positioning the
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front Rear Model Wheel arch height (Tolerance: +12 mm 24 mm ( +0.47 in 0.94 in)) mm (in) 376 (14.8) Camber (Tolerance: 0 45 Differences between
More informationNDA-25B MKI Fast Rescue Boat Davit
NDA-25B MKI Fast Rescue Boat Davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0039 Rev. Date: 14.11.2016 Rev. No: 2 Tel: +47 37 05 85 00 Fax: +47 37 05
More informationMODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO.
9-0688 MODEL NO. 00-800 & UP MODEL NO. 0-800 & UP MODEL NO. 5-800 & UP MODEL NO. -800 & UP MODEL NO. 0-800 & UP SKID SPRAYER with the Centrifugal Pump FORM NO. 95-9095 SET-UP AND PARTS CATALOG SAFETY AND
More informationRotating PWC Lift Installation Guide
Rotating PWC Lift Installation Guide 800 259 8715 www.boathoistusastore.com BHUSA PWC Lift Installation Guidelines by Boat Hoist USA Check all parts on the packing list to ensure you have all the parts
More informationInstallation and Maintenance Manual MRW-02. Radial Winch 80.3 ST
MRW-02 Index Introduction 3 Technical characteristics 3 Weights 3 Maximum working load 3 Outline 3 Installation 4 Installation procedure 5 Positioning the self-tailing arm 8 Maintenance 9 Washing 9 Maintenance
More informationTOYOTA PRIUS PLUS LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-47100 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Nut 4 1 Instructions Hardware Bag Contents Item # Quantity Reqd. Description 1 2
More informationGES-45 MKI. Enterprise No.: NO Tel: Fax:
GES-45 MKI Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATION AND CERTIFICATION
More informationSCION tc SWAY BAR SET Preparation
SCION tc 2011- SWAY BAR SET Preparation Part Number: PTR07-21100 Kit Contents: Item # Quantity Reqd. Description 1 1 Front Stabilizer Bar 2 1 Rear Stabilizer Bar 3 1 Hardware Bag 4 1 Instructions Hardware
More informationInstallation and Maintenance Manual MRW-01. Radial Winch 40.2 ST
MRW-01 Index Introduction Technical characteristics Weight Maximum working load Outline Installation Procedure 1 Procedure 2 Installation procedure Positioning the self-tailing arm Maintenance Washing
More information2003 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX
2003 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX CHASSIS SECTION FRONT SUSPENSION FS REAR SUSPENSION RS WHEEL AND TIRE SYSTEM WT This service manual has been prepared to provide SUBARU service personnel
More informationPerforma Winch 50.2 STP
MRPW-03 Performa Winch 50.2 STP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation procedure 6 Positioning the self-tailing arm 7 Maintenance
More informationOPERATIONS MANUAL LEVER CHAIN HOIST
OPERATIONS MANUAL LEVER CHAIN HOIST IMPORTANT SAFETY INFORMATION Please read, understand and follow all safety information contained in these instructions prior to the use of this hoist. Retain these instructions
More information1 Planning Information
Flight Design GmbH Rudder Centering Fork - Control Stop Replacement 1 Planning Information 1.1 Affected Aircraft Type: Model: Serial Number: Applicable Countries: CT CTLS F-08-04-09, F-08-04-10, F-08-04-11,
More informationACCLAIM OPERATOR, PARTS, AND INSTALLATION MANUAL BX4330 ACCLAIM
ACCLAIM OPERATOR, PARTS, AND INSTALLATION MANUAL BX4330 ACCLAIM Tow Bar Class III (5000 lb) 2 Inch Coupler TOWING PRODUCTS DIVISION Page 1 of 8 292-2205 4/23/09 SAFETY DO NOT INSTALL, OPERATE OR USE THIS
More informationGES-52 MKI. Enterprise No.: NO Tel: Fax:
GES-52 MKI Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATION AND CERTIFICATION
More informationOperating and Assembly Manual
Model 1080 Operating and Assembly Manual Midwest Equipment Manufacturing, Inc. 5225 Serum Plant Road Thorntown, IN 46071 08-02-16 SAFETY RULES Remember, any power equipment can cause injury if operated
More informationPerforma Winch 70.2 STP
MRPW-03 Performa Winch 70.2 STP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation procedure 7 Positioning the self-tailing arm 8 Maintenance
More informationPRODUCT MANUAL 52ST (V.4.0) 52ST FS (V.4.0.F) RON-WPM ST/52STFS-Rev.3
PRODUCT MANUAL 52ST (V.4.0) RON-WPM-710021-52ST/52STFS-Rev.3 52ST (V.4.0) p2 EXPLODED VIEW ITEM. 3 MODEL ST - PART No. 540406 ITEM. 3 MODEL ST FS - PART No. 540411 ITEM. 16 - PART No. 589111 ITEM. 15 -
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More informationNRB-20 MKI Rescue boat davit
NRB-20 MKI Rescue boat davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATIONS
More informationBLASTRAC EBE Rigging System Floating Roof
BLASTRAC EBE Rigging System Floating Roof RIGGING SYSTEM FOR PROCESSING VERTICAL STEEL STORAGE TANK SURFACES The BLASTRAC EBE Floating Roof rigging systems are especially developed for the BLASTRAC EBE
More information4ACMH 04 (6E03) 5CMH 04 (6E33)
MH 04 (6E03) MH 04 (6E33) 1C6E0-700E1 ( 2C6E0-700E1 ) FOREWORD This Parts Catalogue is related to the parts for the model(s) on the cover page. When you are ordering replacement parts, please refer to
More informationI. General Safety Precautions
1 2 ATV/UTV WINCH Thank you for purchasing a. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available at the
More informationYUDO SINGLE VALVE NOZZLE SERIES III V E R. N O M N S V E N O
SINGLE VALVE III Instruction Manual YUDO SINGLE VALVE NOZZLE SERIES III V E R. N O. 0 2 0 9 M N S V E N O Greetings Thank you for using YUDO Single Valve III System. YUDO fabricated Single Valve III System
More information4 & 6 4-Link Suspension Systems. Ford Super Duty 4WD Part#: ,
Part#: 013013, 013014 4 & 6 4-Link Suspension Systems Ford Super Duty 4WD 2011-2016 Rev. 051817 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read
More informationfile://c:\programdata\proquestms\partsmanagerpro\print\ ~13~11~5.html
C60TLRZ 00 file://c:\programdata\proquestms\partsmanagerpro\print\8-9-0 ~~~5.html Page of 6 8/9/0 C60TLRZ 00 / TOP COWLING 0 Yamaha Motor Corporation, U.S.A. All rights reserved. C60TLRZ 00 file://c:\programdata\proquestms\partsmanagerpro\print\8-9-0
More informationConvertible - Rated 3 4-Ton /2-Ton Nylon Strap Hoists Refer to any questions about the use, application, repair or testing of this hoist to:
Operating and Servicing Instructions for Convertible - Rated 3 4-Ton - 1 1 /2-Ton Nylon Strap Hoists Refer to any questions about the use, application, repair or testing of this hoist to: Hubbell / Chance
More informationAdjustable Speaker Mount GRAVIS 12
Adjustable Speaker Mount GRAVIS 12 User's Manual Translation of the original instructions Version 3.3 Released: 19.01.2017 Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße
More informationShock Absorber TTX39 for BMW R1200GS Rear BM Spare Parts List
Shock Absorber TTX39 for BMW R1200GS Rear BM 6760 Spare Parts List Safety Precautions Note! The shock absorber is a very important part of the vehicle and will therefore affect the stability of the vehicle.
More informationAdjustable Speaker Mount GRAVIS 8
Adjustable Speaker Mount GRAVIS 8 User's Manual Translation of the original instructions Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße 14 D-30179 Hannover TEL +49 (0)
More informationRoad Armor Triple Axle Equalizer by Trailair
Road Armor Triple Axle by Trailair OEM INSTALLATION MANUAL Rev: 06.26.2017 Page 1 TABLE OF CONTENTS System Information 2 Triple Axle Options 2 Safety Information 2 Resources Required 2 Installation 3 Rear
More informationTailgates By THIEMAN WT20, 30 & 40 PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. HIEMAN
WEIGHTLIFTER Tailgates By THIEMAN WT20, 30 & 40 OWNERS MANUAL/PARTS LIST! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NATIONAL TRUCK
More informationTADANO MODEL TR-300XL-3-30 TON CAPACITY WORKING RANGE CHART. LIFTING CHARTS - Rough Terrain Cranes
LIFTING CHARTS - Rough Terrain Cranes TADANO MODEL - 30 TON CAPACITY WORKING RANGE CHART NOTE: Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface.
More informationPRODUCT MANUAL 34ST (V.2.0) 34ST FS (V.2.0.F) RON-WPM ST/34STFS-Rev.3
PRODUCT MANUAL 34ST (V.2.0) RON-WPM-710229-34ST/34STFS-Rev.3 34ST (V.2.0) EXPLODED VIEW p2 ITEM. 3 MODEL ST - PART No. 537551 ITEM. 3 MODEL ST FS - PART No. 537511 ITEM. 5 - PART No. 729021 ITEM. 11 MODEL
More information3 Axles and brakes. 3.1 Function and construction of the axles Construction Function
3 Axles and brakes 3.1 Function and construction of the axles 3.1.1 Function Each wheel has an independent suspension system in the axle body (1), so that individual wheel suspension is provided. The swinging
More informationImportant. Contents. Contact us:
Operator's Manual Second Edition First Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall
More informationAerial Platform with Spec No.: AT-146-3A-00090
Supplement AT-146TE-3/S1-1E-2 Aerial Platform with Spec No.: AT-146-3A-00090 This document is a supplement to the existing service manual with Publication No.: AT-146TE-3/S1-1E. The specifications of this
More informationInstructions for Parts Books
Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:
More informationABACO GLASS LIFTER (AGL38)
ABACO MACHINES ABACO GLASS LIFTER (AGL38) ABACO MACHINES (USA) 14508 S. Garfield Ave., Paramount, CA 90723, USA Tel : 310-532-0366 Fax : 310-532-0499 Email : sales@abacomachines.com Website : www.abacomachines.com
More informationLEXUS IS 250/350/250 AWD REAR GS SHOCK ABSORBERS Preparation. Part Number: PTR PTR PTR
Preparation Part Number: PTR13-53082 PTR13-53092 PTR13-53095 Kit Contents Item # Quantity Reqd. Description 1 1 Shock Absorber 2 1 Hardware Bag 3 Hardware Bag Contents Item # Quantity Reqd. Description
More informationHeavy Duty Hoist WARNING. General Safety Precautions. Thank you for purchasing a
Heavy Duty Hoist Thank you for purchasing a Hoist. This manual covers operation and maintenance of the hoist. All information in this publication is based on the latest production information available
More informationINSPECTION FOR CORRECT VENTING OF THE OIL SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) SB R1 SB R1 MANDATORY
AIRCRAFT ENGINES SERVICE BULLETIN INSPECTION FOR CORRECT VENTING OF THE OIL SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) R1 R1 MANDATORY Repeating symbols: Please, pay attention to the following symbols
More informationRotary Damper. Type 57: 40~350mm (1 1/2 ~14 ) Type 56: 400mm (16 ) Type 75: 450~600mm (18 ~24 ) Contents
Serial No. H-V038-E-8 Rotary Damper Type 57: 40~350mm (1 1/2 ~14 ) Type 56: 400mm (16 ) Type 75: 450~600mm (18 ~24 ) Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General
More informationER2 Twin Hook Electric Chain Hoist
OM-ER2TWZ-CEE-00 Original Instruction ER2 Twin Hook Electric Chain Hoist (250kg to 5t) Operation Manual (TWER2/TWER2M/TWER2SP/TWER2SG) Introduction KITO Twin Hook Electric Chain Hoist is intended to make
More informationLOAD CHART MANUAL FOR RT55 ROUGH TERRAIN CRANE
Address:Quantang Indust=rial Park, 2nd Yuanda Road, Changsha Economic and Technological Development Zone, Hunan Province, China Postcode: 410131 Website: www.zoomlion.com LOAD CHART MANUAL FOR RT55 ROUGH
More informationMidget-530 MKII, Waterjet
Midget-530 MKII, Waterjet Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATION AND
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationXT Winches. Installation and Maintenance Manual XT16.2AL, XT16.2CH, XT16.2R XT30.2AL, XT30.2CH, XT30.2R
XT Winches Installation and Maintenance Manual For Models XT6.2AL, XT6.2CH, XT6.2R XT30.2AL, XT30.2CH, XT30.2R Antal srl unipersonale, Via del Progresso, 0, 3527, Padova, Italy. Tel. +39 049 870265. Fax:
More information2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014
2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &
More informationPerforma Winch 40.2 STP
MRPW-02 Performa Winch 40.2 STP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation procedure 6 Positioning the self-tailing arm 7 Maintenance
More informationOperating and installation instructions
DP30 DP32 DP33 DP34 Contents 1.0 General information on operating instructions... 2-2 2.0 Notes on possible dangers... 2-2 2.1 Significance of symbols... 2-2 2.2 Explanatory notes on safety information...
More informationMS2200, MS2500, and MS3000 Suspension Installation Manual ON/OFF HIGHWAY SUSPENSION SYSTEM
MS22, MS25, and MS3 Suspension Installation Manual ON/OFF HIGHWAY SUSPENSION SYSTEM 972.547.62 8.445.736 FAX: 972.542.97 725 E. UNIVERSITY ST. McKINNEY, TEXAS 7569 www.watsonsuspensions.com Watson & Chalin
More informationBelt Conveyor Pull Rope Switch Types HEN, HEK and SEM OPERATING INSTRUCTIONS
Belt Conveyor Pull Rope Switch Types HEN, HEK and SEM OPERATING INSTRUCTIONS 2 CE-Sign and Conformity The device meets the requirements of the valid European and national regulations. Conformity has been
More informationOPERATION MANUAL Electric Wire Wrapper TDWW501B
OPERATION MANUAL Electric Wire Wrapper TDWW501B 4270 Airborn Drive Addison, Texas 75001 USA t. 972.248.1999 f. 972.248.1991 info@startinternational.com www.startinternational.com INTRODUCTION Thank you
More information7. MT Gear Shift Lever
7. A: REMOVAL 1. STI MODEL 1) Disconnect the ground cable from battery. 2) Remove the gear shift knob by turning it counterclockwise. 3) Remove the console box assembly.
More informationABACO MACHINES OPERATION MANUAL STONE/STEEL/GLASS/WOODS LIFTER (ASSGWL20) ABACO MACHINES (USA)
ABACO MACHINES OPERATION MANUAL STONE/STEEL/GLASS/WOODS LIFTER (ASSGWL20) ABACO MACHINES (USA) 14508 S. Garfield Ave., Paramount, CA 90723, USA Tel : 310-532-0366 Fax : 310-532-99 Email : sales@abacomachines.com
More informationLOAD CHART MANUAL FOR RT60 ROUGH TERRAIN CRANE
LOAD CHART MANUAL FOR RT60 ROUGH TERRAIN CRANE Address:Quantang Indust=rial Park, 2nd Yuanda Road, Changsha Economic and Technological Development Zone, Hunan Province, China Postcode: 410131 Website:
More informationRev. 10/27/2015 CDL-2000, MANUAL
VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com CDL-2000
More informationAltec LMAP. (Load Moment and Area Protection) Telescopic Boom Cranes. Calibration
Altec LMAP (Load Moment and Area Protection) Telescopic Boom Cranes Calibration Contents System Components...1 Anti-Two Block...1 Area Alarm...1 Boom Angle Sensor...1 Display...1 Extension Sensor...2 Function
More informationInstallation Instructions Lockey TB 250/450/650 Plus Hydraulic Pedestrian Gate Closer (with hydraulically adjustable closing speed)
Installation Instructions Lockey TB 250/450/650 Plus Hydraulic Pedestrian Gate Closer (with hydraulically adjustable closing speed) The Lockey TB 250/450/650 Plus Pedestrian Gate Closer is a fully featured
More informationBlohm+Voss BVE/S-750 Elevator/Spider 4 ½ 14 Pipe Range Diameter
Read before first use! Blohm+Voss BVE/S-750 Elevator/Spider 4 ½ 14 Pipe Range Diameter Part No. 710000-Y-H hydraulic version Blohm + Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Telephone
More informationNDA-25 MKI - Rescue Boat Davit
NDA-25 MKI - Rescue Boat Davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0038 Rev. Date: 11.10.2016 Rev. No: 3 Tel: +47 37 05 85 00 Fax: +47 37 05 85
More informationPackage Contents Part A (3) I-Beam (1) Base (2) Other parts
Page 1 Installation Instructions for 81245 Adjustable Height Gantry Crane 1-Ton Capacity Table of Contents Important Safety Information pg. 2 Specific Operation Warnings pg. 2 Main Parts of Product pg.
More informationSupplement to Spare Parts Catalogue. Model : FT Dual Transmission - F
Supplement to Spare Parts Catalogue Model : FT - 60 Dual Transmission - F10001760 CONTENTS Tab. No. Sheet No. DESCRIPTION Page No. 1 101764-8 HEAD LIGHT, REAR LIGHT AND PLOUGH 1 LAMP 2 101766A-7 SHEET
More informationTRAILER INSTALLATION INSTRUCTIONS
TRAILER INSTALLATION INSTRUCTIONS 8A000450 DuraMax 20,000 LB. CAPACITY Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 www.linkmfg.com QUESTIONS? CALL CUSTOMER SERVICE 1-800-222-6283 Refer
More informationSUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 SUENSION SYSTEM Suspension system Vehicle is unstable Bottoming Sways/pitches Wheels shimmy Abnormal tire wear Vehice pull PROBLEM SYMPTOMS TABLE Use the table below to help
More informationRepair Parts Model 4/29 Crane
4/29: 99903041: 20111201 PARTS-1 Repair Parts Model 4/29 Crane IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 641-923-3711 TECHNICAL SUPPORT FAX: 641-923-2424 MANUAL PART NUMBER: 99903041 Iowa
More information