Chassis Dimensions. Calculations Height, Width, Ground clearance 02: Februari This document may be revised without notice
|
|
- Sheila Gray
- 5 years ago
- Views:
Transcription
1 Calculations Height, Width, Ground clearance 02:20-01 Februari 2018
2 2
3 Contents Description 4 Definitions 5 Pictures of some dimensions 6 Dimensions Calculations Front with Leaf springs 7 Front with Air suspension 9 Rear with Leaf springs 10 Rear with Air suspension 12 Tyre dimensions 13 Truck height 14 Chassis width 15 Ground clearance 18 3
4 Description In this document you will find the formulas for calculations of some dimensions e.g.: Top of frame to ground at centre line of front axle at chassis weight Top of frame to ground at centre line of front axle at max axle weight Top of cab roof to ground at chassis weight. The formulas for the calculations are divided in a front and a rear part and by configuration and suspension. The tables are valid for P-, G- and R-series and are presented on the same page as the formulas for the calculations of the chassis dimensions. The height calculation is a preliminary attempt to foresee the height. There are many factors that affect the height. The tolerance in the calculation is approximately +/-25 mm if the appropriate weights are used. When applicable the BEP-codes according to standard ISO :2006 are given in addition with the Scania names. If nothing else is stated mm and kg should be used as units in the calculations. 4
5 Definitions A (L011) Axle distance AT (L015) Theoretical axle distance. Distance between front and rear load distribution centres. E (H042.2) Distance between upper edge of frame and upper edge of tyre at 2 nd front axle (8x2, 8x4 and 8x2*6). At parallel max. compression. F Distance between upper edge of frame and upper edge of tyre at 2 nd front axle (8x2, 8x4 and 8x2*6). At parallel max. axle load. H Distance between rear tyre inner edges KA KB M NA NB (W003.1) Max. distance between front wheel outer bolts (W003.n) Max. distance between rear wheel outer edges on double mounted tyres. Single mounted tyre on tag axle behind rear axle can exceed the measurement in some cases (W013.1) Track width front axle/axles. Distance between tyre centre LH side and tyre centre RH side on axle. (W013.n) Track width rear axle/axles with twin mounted tyres. Distance between centre of twin mounted tyres LH side and centre of twin mounted tyres RH side on axle. (W013.n) Rear tag axle track width in single wheel configuration. Distance between tyre centre LH side and tyre centre RH side on axle. Oc (H001) 1 Top of cab roof to ground at chassis weight S (H015.n) Distance between the lowest point of front axle/axles and ground T (H016.n) Distance between the lowest point of driven rear axle/axles and ground U Distance between upper edge of frame and ground at first front axle. Uc (H035) U at chassis weight front Um (H036) U at max. axle weight front V Distance between upper edge of frame and ground at rear load distribution centre. Vc (H039) V at chassis weight rear Vm (H040) V at max. axle weight rear X Distance between upper edge of frame and upper edge of tyre at 1st driven rear axle. At max axle load. XX Distance between upper edge of frame and upper edge of tyre with raised tag axle. YA (H042.n) Distance between upper edge of frame and upper edge of tyre at 1st driven rear axle. At parallel max. compression. YB (H042.n) Distance between upper edge of frame and upper edge of tyre at tag axle. At parallel max. compression. 1) Oc measured to the cab roof. Parts mounted on the roof are not included, ex air deflectors. Parameters A1 Spring constant (front) [mm/kg] B1 Initial value for spring deflection front. [mm] C1 Top of frame to centre line of front axle (air suspension). [mm] D1 Drop centre (front) [mm] E1 Top of frame to centre line of 2nd front axle at parallel max setting. [mm] F1 Theoretical tyre radius. [mm] G1 Rolling radius at chassis weight front. [mm] H1 Rolling radius at max axle weight. [mm] I1 Spring constant (rear). [mm/kg] J1 Initial value for spring deflection rear. [mm] K1 Top of frame to centre line of 1st rear drive axle. [mm] L1 Rolling radius at chassis weight rear. [mm] M1 Top of frame to centre line of rear drive axle at parallel max setting (leaf springs). [mm] N1 Top of frame to centre line of rear drive axle at parallel max setting (air suspension). [mm] P1 Top of frame to top of cab roof. [mm] S1 Top of frame to centre line of tag axle in raised position. [mm] T1 Top of frame to centre line of tag axle at parallel max setting. [mm] V1 Tyre radius proportional weight in between G1 and H1. [mm] W1 Tyre radius proportional weight in between L1 and H1. [mm] X1 Distance, parallel frame, between centre line of front axle and highest point of cab roof. [mm] 5
6 Pictures of some Dimensions U with one front axel U with two front axles Oc and X1 6
7 Dimensions Calculations Front with Leaf springs All configurations U Axle weight front A1 B1 D1 V1 No. of frontaxles U C U m Chassis weight front (BEP H035) A1 B1 D1 G1 No. of frontaxles Maxaxle weight front (BEP H036) A1 B1 D1 H1 No. of frontaxles 8x2, 8x2*6, 8x4, 10x4*6 E(BEP H042.2) F1 E1 1) Maxaxleweight front F F1 A1 B1 D1 2 1) Table for E1 is located on the next page Leaf springs A1 B1 2) Front axle D1 2x AM620 / AM621 /AM x AM x32 (4x4, 6x6) AM x AM900 / AM901 / AM800T 3 3x29 (4x4, 6x6) AM x AMD901 / AMD x28 (4x4, 6x6) x x15 (4x4, 6x6) x x ) For trucks with two front axles add 5mm. See section Tyre dimensions for F1, G1 and H1. 7
8 Front spring type D1 A Front (BEP L011) axle weight (tonnes) N/S: 8x2A/Z 8x4A 8x2*6 10x4*6 8x4Z: 4x30 BT201B 8x4Z: 4x30 BT201I 8x4Z: 4x41 2x38+2x45 10x20/90 BT201B E1 Not GB tipper 8x4Z 4x41 2x38+2x45 10x20/90 BT201I H: 8x2A 8x2*6A 8x4A 8x4Z: BT300B 8x4Z: BT301S 8x4Z: BT301B 2x x x , , , , x < < x x x x4Z: BT400S Front spring type D1 A Front (BEP L011) axle weight 8x4Z: 4x41 2x38+2x45 BT201B E1 GB tipper (tonnes) 2x x x x x4Z: 4x41 2x38+2x45 BT201I 8
9 Front with Air suspension All configurations U C1 V1 U C U m (BEP H035) (BEP H036) C1 G1 C1 H1 8x2, 8x2*6, 8x4, 10x4*6 E(BEP H042.2) F1 E1 F F1 C1 C1 Air suspen sion Chassis height Normal Low Extra low Front axle AMA860 AMA740 AMA950 AMA860 1) AMA860 Elevated 5) 692 2) 665 3) 635 7) 607 8) 483 Driving Alt. Driv ELC 4 Lowered 6) ) For 6x2/4 and 6x2/2 see chassis height Extra low 2) For 8x2, 8x2*6, 8x4, 10x4*6, C1 = 632 mm. 3) For 8x2, 8x2*6, 8x4, 10x4*6, C1 = 638 mm. 4) Not valid for 6x2/4 and 6x2/2 chassis height Low. 5) Maximum height for air spring. 6) Including the compression of the bump stop. 7) For 8x2, 8x2*6, 8x4, 10x4*6, C1 = 608 mm 8) For 8x2, 8x2*6, 8x4, 10x4*6, C1 = 580 mm See section Tyre dimensions for F1, G1 and H1. Air suspension E1 Front Ad (BEP L012.1) Front springs D1 Drop centre Ad 8x2B 8x2*6B 8x4B 10x4* Air Front axle D1 AMA AMA AMA
10 Rear with Leaf springs All configurations V I1 Axle/bogie weight rear J1 W1 V c (BEP H039) I1 Chassis weight rear J1 L1 Vm(BEP H040) I1 Maxaxle/bogieweight rear J1 H1 X F1 - (I1 Max axle/bogie weight rear J1) XX F1 395 Notwith Ad 3100 XX F1 428 With Ad 3100 YA (BEP H042.n) F1 - M1 YB (BEP H042.n) YB (BEP H042.n) F1-390 F1-423 (Not with Ad 3100) (With Ad 3100) See section Tyre dimensions for F1, L1 and H1. Single axle Leaf springs Axle weight I1 J1 M1 3x26+2x26 < 6000 kg ) 5) 6) 375 3x26+2x26 > 6000 kg ) 5) 6) 375 7x15+6x14 < 4700 kg ) 375 6) 7x15+6x14 > 4700 kg ) 375 6) 9x15+6x14 < 5400 kg ) 6) 405 2) 6) 9x15+6x14 > 5400 kg ) 6) 405 2) 6) 12x15+6x14 < 6900 kg ) 405 6) 12x15+6x14 > 6900 kg ) 405 6) 16x12/16x11-0, x ) 375 7) 5x22 3) < kg ) 7) 375 7) 1x15+10x ) 375 7) 1x15+10x13 3) < kg ) 7) 375 7) 3x24+1x41 < 5000 kg ) 2) 6) 375 3x24+1x41 > 5000 kg ) 2) 6) 375 5x16+2x27 < 4000 kg ) 2) 6) 375 5x16+2x27 > 4000 kg ) 2) 6) 375 6x15+5x22 < 4600 kg ) 9) 405 6) 9) 6x15+5x22 > 4600 kg ) 9) 405 6) 9) 1) With straight front axle (AM900) add 78 mm 2) On 4x4 add 116 mm 3) With raised tag axle (2nd tag axle for 8x2/4) 4) For ad 3100 subtract 30 mm. 5) On 4x4 add 141 mm 6) With AD1503P add 6 mm 7) With AD1503P remove 6 mm 8) On 4x4 add 146 mm 9) On 4x4 add 60 mm 1) 5) 6) 1) 5) 6) 1) 6) 8) 1) 6) 8) 1) 6) 8) 1) 6) 8) 10
11 Bogie Leaf springs Bogie I1 J1 1) M1 1) 4x30 BT201B -0, x30 BT201I -0, x41 BT201B -0, x41 BT201I -0, x38+2x45 BT201B< 7500 kg x38+2x45 BT201B>=7500 kg x38+2x45 BT201I<7500 kg x38+2x45 BT201I>=7500 kg x20/90 BT201B -0, x20/90 BT201I -0, x20/90 BT300B x30/90 BT300B x48 BT300B x41+2x48 BT300B<7500 kg x41+2x48 BT300B>=7500 kg x20/90 BT300I BT301I 8x30/90 BT300I BT301I 5x48 BT300I BT301I 4x41 BT300I x38+2x45 BT300I<7500 kg x38+2x45 BT300I>=7500 kg x41+2x48 BT300I<7500 kg BT301I<7500 kg 2x41+2x48 BT300I>=7500 kg BT301I>=7500 kg 8x30/90 BT301S x48/90 BT301S x30/100 BT301B x48/100 BT301B x30/100 BT400S x48/100 BT400S ) With AD1503P or AD1603P add 6 mm 11
12 Rear with Air suspension All configurations V K1 W1 V c (BEP H039) Vm (BEP H040) K1 L1 K1 H1 X F1 - K1 XX F1 - S1 YA (BEP H042.n) F1 - N1 YB (BEP H042.n) F1 - T1 Air suspension 4-spring Configuration 4x2 4x2 4x2 6x2 6x2*4 8) n/a 4x2, 6x2, 6x2*4, 8x2*6 2-spring 8) 4x2, 6x2, 6x2*4, 8x2*6 Chassis Normal Low Normal Low Low Extra low height Semi high K1 Elevated 6) 690 4) Driving Alt. Driv. ELC Lowered 7) 395 1) 365 1) 392 1) 392 1) N S T Configuration Chassis height 6x4 8x4 8x4*4 10x4*6 Normal Semi high 6x4 8x4 High Air suspension Normal Semi high 2-spring 6x2/4 6x2/2 8x2/4 9) Low 9) n/a Low 8x2 8x2*6 4x2 Normal Semi high K1 Elevated 6) Driving Alt. Driv. ELC Lowered 7) 392 1) ) ) N S ) T ) ) With ADA1303P with RB/RBP835 add 6 mm 2) Applies only to 8x4*4 & 10x4*6 3) Applies only to 6x2/4 and 6x2/2 4) Remove 30 mm if tractor adaptation. 6) Maximum height for air spring. 7) Including the compression of the bump stop. 8) 4x2/6X2/6x2*4/8x2*6 with ADA400, ADA1303 with disc brakes 9) With frame rear end U. See section Tyre dimensions for F1, L1 and H1. 12
13 Tyre Dimensions Tyre F1 G1 L1 H R R R R R R /70R R /80R /55R /60R /80R /70R /45R /60R /70R /80R /95R /50R /70R /50R /90R /55R /65R
14 Truck height All cabs except CP28/31 CrewCab Oc(BEP H001 1) ) Uc P1 1) Oc measured to the cab roof. Parts mounted on the roof are not included, ex air deflectors. Cab type P1 P1 measured without roof hatch. CP CP14 on 4x4/6x6 1) 1833 CP CP CP19 on 4x4/6x6 2) 2088 CP19L 1822 CP19L on 4x4/6x6 2) 1839 CP19H 2275 CG CG CG CG19L 2062 CG19H 2514 CR CR ) Also valid for trucks with CP14 cab and CR19 on 4x4/6x trailer connection behind cab. CR19L ) Also valid for 6x2/2, 6x2/4 and 8x2/4 CR19L on 4x4/6x with axle distance larger than CR19H ) P1 measured with roof hatch. CR19T 3) 2904 Standard equipment on CR19T CP28/31 CrewCab Oc(BEP H001 Vc Uc K AT 1) ) Uc P1 ( K X1) 1) Oc measured to the cab roof. Parts mounted on the roof are not included, ex air deflectors. Cab type P1 X1 CP28 CrewCab CP31 CrewCab
15 Chassis width KA (BEP W003.1) = Max distance between front wheel outer nuts AM620/621 AM/AMA740 AM920 Rim AM/AMA860 AM900 AM/AMA950 AMD x x x x Add 20 mm for aluminium disc rims KB (BEP W003.n) = Max distance between rear tyre sides outer edges 1) Tyre Rim 11.00R R x R x8.25 2) R R R x R x9.00 2) R x /70R x /70R x8.25 2) /80R x /55R x /60R x /80R x /80R x9.00 2) /70R x /70R x9.00 2) /60R x /70R x /80R x /95R Add 20 mm for aluminium disc rims 1)Measurement is valid for double mounted tyres. Single mounted tyre on tag axle behind rear axle can exceed the measurement in some cases 2) Optional wheel 15
16 H = Distance between rear inner tyres inner edges Tyre Rim 11.00R R x R x8.25 1) R R R x R x9.00 1) R x /70R x /70R x8.25 1) /80R x /55R x /60R x /80R x /80R x9.00 1) /70R x /70R x9.00 1) /60R x /70R x /80R x /95R Add 20 mm for aluminium disc rims 1) Optional Wheel M (BEP W013.1) = Front track width AM620/621 AM/AMA740 AM920 Rim AM/AMA860 AMD901 AM900 AM/AMA x x x x Add 20 mm for aluminium disc rims 16
17 NA (BEP W013.n) = Rear track width Rim All rear axle 22.5x x x Add 20 mm for aluminium disc rims NB (BEP W013.n) = Rear tag axle track width with single wheel Rim ASA700 ASA720 ASA760 ARA760 ARA820 ARA x x x x Add 20 mm for aluminium disc rims 17
18 Ground clearance At max axle weight S (BEP H015) = Distance from front axle lower edge to ground Tyre AM620 AM621 AM740 AMA740 AM920 AM860 AMA860 AM900 AM950 AMA950 AMD R R R R R R /70R /80R /60R /80R /70R /60R /70R /80R /95R /50R /70R /50R /55R /65R
19 T (BEP H016) = Distance from rear axle lower edge to ground Tyre (ADA1100, AD/ADA1300, ADA1302) 1) ADA1103 AD/ADA1303 ADA1304 R560/R660/RB660/ RB662 (ADA1100, AD/ADA1300, ADA1302) 1) ADA1103 AD/ADA1303 ADA1304 R780/R782 (AD1101P, AD1300P) 1) AD/ADA1303P RP/RBP735 (AD/ADA1501P, ADA1502P, AD1600P) 1) AD1503P ADA1303P AD1603P RP/RBP R R R R R R /70R /80R /55R /60R /80R /70R /60R /70R /80R /95R ) Older denominations 19
Measurement designations. General. BEP codes
BEP (Bodywork Exchange Parameter) are codes that identify unique targets on the vehicle to make information transfer between the vehicle manufacturer and bodybuilder simpler. The BEP codes follow the international
More informationRear end adaptations. Adapted length of rear overhang. Variant codes for some commonly occurring dimensions
Adapted length of rear overhang Adapted length of rear overhang The rear overhang can be ordered from the factory in length increments of 10 mm between the limit values 780 mm and 5,200 mm (see illustration).
More informationP 360 and P 400 Euro 5 added to range Scania P-series available with bigger engines
PRESS info P09401EN / Per-Erik Nordström 30 April 2009 P 360 and P 400 Euro 5 added to range Scania P-series available with bigger engines Together, Scania s P-series and the new high-torque 13-litre EGR
More information65C15D TECHNICAL DESCRIPTION. ( Torsion bar ) N. : A4HB6DT1
TECHNICAL DESCRIPTION ( Torsion bar ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any time. 1 Gearbox S6-300
More informationCODE 10 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FALLING OBJECT PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS
CODE 10 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FALLING OBJECT PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS 1 TABLE OF CONTENTS INTRODUCTION... 3 1. DEFINITIONS... 3 1.1 Agricultural
More informationRigid 8 2. Rigid 8 4
DRIVE / CHASSIS HEIGHT / WHEELBASE (dimensions in dm) Rigid Rear 34 40 40 Rigid 6 2 Rear 48 48 48 Rigid 6 4 Rear Rigid 8 2 Rear Pusher Tridem 62 Rear Tag Tridem Rigid Pusher Tridem 64 64 53 53 47 1 chassis
More information65C18 (E4) ( EURO 4 )
TECHNICAL DESCRIPTION 6C18 (E4) ( EURO 4 ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time. 1 Gearbox
More information35C12 (E4) ( EURO 4 - Transversal leaf )
TECHNICAL DESCRIPTION 35C (E) ( EURO - Transversal leaf ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any
More information50C15 (E4) ( EURO 4 )
TECHNICAL DESCRIPTION 50C15 (E) ( EURO ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time. 1 50C15 (E)
More informationML75E17 ( EURO 3 - NEW )
TECHNICAL DESCRIPTION ( EURO 3 - NEW ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any time. 1 Gearbox 855.5
More information2,000 LB. CAPACITY S-20 - BTR HUB GROUP
2,000 LB. CAPACITY S-20 - BTR HUB GROUP STANDARD GREASE LUBE PARTS HUBS Item Part # Description Item Part # Description Bolt Circle 602 Bearing Kit - 1 Hub 25 8-441 Plain Hub - tapped 4 on 4.00 1 10-9
More informationOverview. Trailing arm 100 mm wide. Single leaf 1x57. Single leaf 1x57
Overview Sheet I Air suspension axles and suspensions Axle load Trailing arm 100 mm wide Air bag Axle type with disc brake TSB 4312 Ride height FH (mm) to drawing Single leaf 1x57 415-560 Sheet 1a Air
More informationAxle load calculations
All types of transportation work using trucks require the truck chassis to be supplemented by some form of bodywork. The aim of axle load calculations is to optimise the chassis and bodywork location.
More informationTowing units. General information on towing units PGRT
General information on towing units General information on towing units is a collective term for one or more components with which the vehicle must be equipped in order to tow a trailer. The purpose of
More information35C15 (E4) ( EURO 4 - Torsion bar )
TECHNICAL DESCRIPTION 5C5 (E4) ( EURO 4 - Torsion bar ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any
More information35C15V (E4) ( EURO 4 - Transversal leaf )
TECHNICAL DESCRIPTION ( EURO 4 - Transversal leaf ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time.
More information35S12 (E4) ( EURO 4 )
TECHNICAL DESCRIPTION 5S (E4) ( EURO 4 ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time. 5S (E4) Gearbox
More informationBODYWORK CALCULATIONS 2
Table of content BODYWORK CALCULATIONS...2 PRINCIPLES OF CALCULATION...3 OPTIMIZING LOAD...6 EXAMPLE OF CALCULATION...7 Example 1 4X2 Tractor with two axles...7 Example 2 6X4 Tractor with three axles...9
More informationF700 F800 F950 F957 F958
Scania chassis frame range The chassis frame consists of 2 frame side members. Scania chassis frame range More information on a specific chassis is found in the individual chassis specification (ICS) and
More informationML100E18 ( EURO 3 - NEW )
TECHNICAL DESCRIPTION ML100E18 ( EURO 3 - NEW ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any time. 1 Gearbox
More informationFORD TRUCKS 2533D LR EURO6
FORD TRUCKS 2533D LR EURO6 3120 2540 1500 3800 1320 1330 7950 Basic Features Vehicle Type Light Tipper 6x2 Emission Euro 6 Cabin Type Low Roof Sleeper Cab Wheelbase (mm) 3800 Engine Type Ecotorq 9 liters
More informationCONTENTS AT Key Dimensions. Load charts. Technical description. Crane dimensions... 4, 5 Range diagram... 6 Area of operation...
CONTENTS Page: Key........................................................................................... 3 Dimensions Crane dimensions........................................................................
More informationAssembly date Current distributor, country ZZ. Gross weight 0 Order Number Order type A Delivery mode CBU
General Information VIN Code YS2G6X600D2093776 Factory warranty,valid until Delivery Date Invoicing date Assembly date 2013 12 04 Current distributor, country ZZ Original distributor, number 00000 Local
More information50C15V (E4) ( EURO 4 )
TECHNICAL DESCRIPTION 50C15V (E) ( EURO ) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time. 1 Gearbox
More informationLIFT TRUCK TECHNOLOGY. Nexen Libero FDL20-25 (2.0t - 2.5t) Diesel Fork Lift. Specification Sheet.
LIFT TRUCK TECHNOLOGY Nexen Libero FDL20-25 (2.0t - 2.5t) Diesel Fork Lift Specification Sheet www.nexenlifttrucks.com Nexen Nexen Nexen Nexen FDL20 FDL20 FDL20 FDL20 Libero Libero Libero Libero 4TNE92
More informationParameters Chassis. Introduction
Introduction To limit the list of parameters in this document, only parameters considered to be of use to bodybuilders are described. For full details of the current parameters for a specific vehicle,
More informationTorsionally rigid bodywork 6. Contents TORSIONALLY RIGID BODYWORK 3. VAN BOXES AND CONTAINERS 4 Mounting van boxes and containers 5
Contents TORSIONALLY RIGID BODYWORK 3 VAN BOXES AND CONTAINERS 4 Mounting van boxes and containers 5 FREEZER AND REFRIGERATOR UNITS 6 TANKERS AND BULK CARGO 6 Mounting - tank 9 Mounting - weighing equipment
More informationML150E28 ( EURO 3 - NEW )
TECHNICAL DESCRIPTION ML150E8 ( EURO 3 - NEW ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any time. 1 ML150E8
More informationII YEAR AUTOMOBILE ENGINEERING AT AUTOMOTIVE CHASSIS QUESTION BANK UNIT I - LAYOUT, FRAME, FRONT AXLE AND STEERING SYSTEM
II YEAR AUTOMOBILE ENGINEERING AT 6402 - AUTOMOTIVE CHASSIS QUESTION BANK UNIT I - LAYOUT, FRAME, FRONT AXLE AND STEERING SYSTEM 1. Write about the requirements of frame and selection of cross section
More informationTRAILER CATALOGUE MADE FOR AUSTRALIAN AUSTRALIAN CONDITIONS FAMILY BUSINESS ESTABLISHED 1964 WARRANTY UPGRADE TO 5 YEARS
TRAILER CATALOGUE AUSTRALIAN MADE FOR AUSTRALIAN CONDITIONS FAMILY BUSINESS ESTABLISHED 1964 WARRANTY UPGRADE TO 5 YEARS ABOUT US Extensive dealer network Servicing QLD, NSW and NT 5 YEAR WARRANTY 50 YEARS
More informationML120EL17/P ( EURO 3 - NEW )
TECHNICAL DESCRIPTION ML10EL17/P ( EURO 3 - NEW ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any time. 1
More informationVehicle Technical Specifications
Vehicle Manufacturer: Volkswagen Year and Model: (99-05) Jetta Mk. 4 This specifications form was developed by SCCA Pro Racing and will be used by the TECHNICAL MANAGER to establish technical compliance
More informationScania at Eurosatory 2012 Maximum modularity tailored solutions are standard
PRESS info P12602EN / Per-Erik Nordström June 2012 Scania at Eurosatory 2012 Maximum modularity tailored solutions are standard Scania's strategy of continuously refining its products means that the truck
More information2012 Isuzu Truck. NPR Diesel Specifications. (Vehicle Specifications Index Section NPR Eco-Max Diesel continued on next page) 2012 Isuzu Truck BRAKES
9.1 NPR Diesel Specifications MODEL GVWR WB ENGINE Model/Displacement HP (Gross) Torque (Gross) Equipment TRANSMISSION STEERING FRONT AXLE Suspension GAWR REAR AXLE Suspension GAWR WHEELS TIRES NPR ECO-MAX
More informationTIRE BASICS GENERAL INFORMATION WHAT S INSIDE A TIRE TREAD BELTS BELT EDGE INSULATION BODY PLIES INNERLINER CASING BEAD SIDEWALL BEAD FILLER
WHAT S INSIDE A TIRE BELTS TREAD BELT EDGE INSULATION BODY PLIES INNERLINER CASING BEAD SIDEWALL The tire s INNERLINER -- keeps air inside the tire. BEAD FILLER The CASING (or CARCASS) the internal substructure
More informationEQUIPMENT HIRE RATES RATES EFFECTIVE 1 ST JULY 2015 ALL RATES ARE GST EXCLUSIVE
S S KUBOTA KX-121-3 RUBBER TRACKED EXCAVATOR (4.5 TONNE) MODEL KX-121-3 Net power - 30.2 kw Digging Force - 1790 kgf Digging Depth - 3.5 m Safe Working Load - 460 kg Operating Weight - 4,100 kilograms
More information01 09 Installation guidelines Air suspension units GL70 GL70HD GL70L GN Air suspension units GL70 GL70HD GL70L
01 09 Installation guidelines Air suspension units GL70 GL70HD GL70L GN0031-1 Air suspension units GL70 GL70HD GL70L can be identified by the hanger brackets with a welded-on support for the eccentric
More informationNEW STOCK. Contact us now for further details OEM: , OEM: OEM: , OEM: ,
DFBODY508 Step Support Bracket RH DFBODY509 Step Support Bracket LH OEM: 1366254, 1368837 DFBODY511 Wind Deflector Outer RH OEM: 1366253, 1368836 DFBODY512 Wind Deflector Outer LH OEM: 1362871 DFBODY513
More informationTIMBERMAX & MORE TRANSPORT SOLUTIONS FOR THE FORESTRY INDUSTRY
TIMBERMAX & MORE TRANSPORT SOLUTIONS FOR THE FORESTRY INDUSTRY TIMBERMAX & MORE FAYMONVILLE offers transport options to suit specific needs in the timber sector Timber transport has a long tradition at
More informationBPW rigid axles with drum brake Ø 300 mm. For axle loads from 6,400 kg to 12,000 kg.
BW rigid axles with drum brake Ø 300 mm. For axle loads from 6,400 kg to kg. NS NZ M 84 Technical Data / N axles Axle cross section Wheel stud Ø / Offset / M 311 2,195 1,500 628 NZF 6410 6,400 3) SN 3015
More informationTorque steer effects resulting from tyre aligning torque Effect of kinematics and elastokinematics
P refa c e Tyres of suspension and drive 1.1 General characteristics of wheel suspensions 1.2 Independent wheel suspensions- general 1.2.1 Requirements 1.2.2 Double wishbone suspensions 1.2.3 McPherson
More informationR5 ROLLING CHASSIS CP0438K SPACE FRAME 1 4, POWDER COAT SPACEFRAME
R5 ROLLING CHASSIS CP0438K SPACE FRAME 1 4,000.00 POWDER COAT SPACEFRAME 1 600.00 CP0105K REAR UPPER WISHBONE (LH & RH) 2 420.00 CP0105 REAR UPPER WISHBONE 1 175.00 OOO555 WISHBONE BUSH 4 8.80 CPK3223
More informationBTS Accessories. Floor Spring Accessories
BTS Accessories Floor Spring Accessories Floor spring accessories Single action aluminium doors For single action aluminium doors Aluminium door straps 2 For flush-closing single action aluminium doors
More informationFM 64TB1 HRX. Core Components - Cab. Cab Interior and Storage Facilities. Instruments and Controls. Cab Comfort and Climate. Seats FM 64TB3 HRX
VOLVO TRUCKS. DRIVING PROGRESS Volvo Regional Branch Contact Details VOLVO FMX FMX 6 x 4 Truck Tractor Single Reduction Namibia (Windhoek) Auto Sueco (Namibia) (Pty) Ltd Te l : + 2 6 4 6 1 2 2 8 5 2 0
More informationMH260E24Y/TN ( CURSOR )
N. : DT 60 00 TECHNICAL DESCRIPTIONS MH60E4Y/TN ( CURSOR ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any
More informationRS 588 SUPPLEMENTAL RESTRAINT SYSTEM CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL
588 SUPPLEMENTAL RESTRAINT SYSTEM CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL 1. PRECAUTION 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Wait for at least 90 seconds after disconnecting the cable to prevent
More informationLIFT TRUCK TECHNOLOGY. Nexen Libero FGL20-25 (2.0t - 2.5t) LPG Fork Lift. Specification Sheet.
LIFT TRUCK TECHNOLOGY Nexen Libero FGL20-25 (2.0t - 2.5t) LPG Fork Lift Specification Sheet www.nexenlifttrucks.com OTHER ENGINE PERFORMANCE DIMENSIONS WHEELS & TYRES WEIGHTS CHARACTERISTICS NEXEN LIBERO
More informationRG Colorado National Media Launch Tuesday 12 June 2012 PRODUCT INFORMATION
RG Colorado National Media Launch Tuesday 12 June 2012 PRODUCT INFORMATION HIGHLIGHTS All-new generation light truck platform and design Designed and developed by global team led by GM Brazil Bigger, bolder
More informationPERSONALISED SPECIFICATION SHEET KERAX X4 XHD GVW 40 T
KERAX 330.35 6X4 XHD GVW 40 T WEIGHTS Wheelbase mm 4.200 GVW Kg 40000 Body/Payload Allowance Kg 25351 Kerb Weight Total Kg 9649 Kerb Weight Front Kg 4809 Kerb Weight Rear Kg 4840 Maximum Front Axle Load
More informationWheelbase mm Maximum Weight (registered) Total (GVW) Kg Payload (C) Kg Kerb Weight total Kg 5125
Renault Midlum D- Range D 18 WEIGHTS Maximum Weight (registered) Total (GVW) Kg 18000 Payload (C) Kg 12875 Kerb Weight total Kg 5125 Chassis cab kerb weight Front axles (Liftable axle down) Kg 3396 Rear
More informationTEST REQUIREMENTS FOR TRUCK STEEL WHEELS SPECIFICATION D'ESSAI DES ROUES EN ACIER DE CAMIONS PRÜFVERFAHREN FÜR NUTZFAHRZEUG - STAHL - RÄDER
EUWA STANDARDS May 2006 TEST REQUIREMENTS FOR TRUCK STEEL WHEELS E S 3.11 SPECIFICATION D'ESSAI DES ROUES EN ACIER DE CAMIONS PRÜFVERFAHREN FÜR NUTZFAHRZEUG - STAHL - RÄDER Page 1/8 1 - SCOPE This Euwa
More informationDRAFT VTS Approved for Racing
DRAFT VTS Approved for Racing Vehicle Manufacturer: Year and Model: Mazda 2008-2015 Mx5 This draft of the listed vehicle s VTS is posted with the specifications that we currently have for the vehicle.
More informationSCHOPF F396C. Aircraft Towing Tractor TECHNICAL DATA & CONFIGURATION
SCHOPF F396C Aircraft Towing Tractor TECHNICAL DATA & CONFIGURATION TECHNICAL DATA Operating weights 45,000 / 50,000 / 55,000 / 60,000 / 70,000 kg Tyres, front + rear 16.00 x 25 18.00 x 25 (70,000 kg)
More informationCODE 4 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS (STATIC TEST)
CODE 4 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS (STATIC TEST) 1 TABLE OF CONTENTS 1. DEFINITIONS... 3 1.1 Agricultural and forestry tractors...
More informationBodywork information in the instrument cluster
The instrument cluster is prepared with options for connecting and setting parameters for various types of function indications to adapt the vehicle's driver environment correctly to its area of use. The
More information31/05/2013P:\INVENTORY\SLOW\krone\Krone surplus parts31may12 31May13.xls
KR/0030413 D8A PULLEY 1 5.95 KR/1394170 D04A PIN 23 2.48 KR/1396650 D01A WEARING SKID (ALSO 1392990) 9 29.95 KR/1396800 D02A DISC 1 87.36 KR/1398000 D05A BLADE 13 1.78 KR/1398820 D07A TINE LONG (N/T) 10
More informationCODE 6 July 2012 CODE 6
CODE 6 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FRONT MOUNTED ROLL-OVER PROTECTIVE STRUCTURES ON NARROW-TRACK WHEELED AGRICULTURAL AND FORESTRY TRACTORS 1 TABLE OF CONTENTS 1. DEFINITIONS... 4 1.1
More informationModel S S2 400
EXPLODED VIEW S2 100 - S2 400 ALUMUNIUM DOME GLASS REINFORCED NYLON 6 BEARING HOLDER & HOLDER ARMS BEARING ALUMINIUM TURBINE/IMPELLER ALUMINIUM DEFLECTOR ALUMINIUM SHAFT ALUMINIUM THROAT & BRACKETS ALUMINIUM
More informationDATA PD LS1..., LS2..., LS3... Lift Axle Valves - Pneumatic. P r o d u c t. Function. Technical Features
C o m m e r c i a l V e h i c l e S y s t e m s P r o d u c t DATA PD-503-200 Function Pneumatic Lift Axle Control Valves are used for the semi-automatic or fully automatic control of air suspended lift
More informationMAN GUIDELINES TO FITTING BODIES. Coupling devices TG Edition 2018 V1.0
MAN GUIDELINES TO FITTING BODIES Coupling devices TG Edition 2018 V1.0 P U B L I S H E R MAN Truck & Bus AG (hereinafter referred to as MAN) Engineering Vehicle Truck Application Engineering Dachauer Str.
More informationDEXTER AXLE LBS. CAPACITY SUSPENSION SYSTEM
5500-7000 LBS. CAPACITY AIRFLEX LIGHT L IGHT TRAILER SUSPENSION SYSTEM Suspension and axle come fully assembled for easy installation The suspension maintains a constant trailer floor height regardless
More informationELECTRIC SCISSOR LIFT
630ES Proportional drive, lift and lower give smooth control Low maintenance nonskid aluminium platform with extension deck and Load Sensing System Low maintenance nonskid aluminium platform with extension
More informationNEW DAILY MY2016 EURO 6
TECHNICL DESCRIPTION NEW DILY MY2016 EURO 6 The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time. - Van
More informationMEILLER Tipping Semi-Trailer HEAVY CLASSIC
MEILLER Tipping Semi-Trailer HEAVY CLASSIC www.meiller.com MEILLER Tipping Semi-Trailer World-renowned for quality since 1850 Intensive development and design work, continuous testing under the most rigorous
More information2,3,4,5,6 Axle Dog Trailers
2,3,4,5,6 Axle Dog Trailers Custom built trailers designed to maximise payload and productivity High Volume, 4 Axle Truck and Dog Combination, Low Profile Tyres, 100m 3 3 Axle Steel Dog Trailer, Built
More informationNPR HD Diesel Specifications
NPR HD Diesel Specifications 11.1 MODEL GVWR WB ENGINE Model/Displacement HP (Gross) Torque (Gross) Equipment TRANSMISSION STEERING FRONT AXLE Suspension GAWR REAR AXLE Suspension GAWR WHEELS TIRES BRAKES
More informationE/ECE/324/Rev.2/Add.123/Amend.1 E/ECE/TRANS/505/Rev.2/Add.123/Amend.1
24 February 2011 Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions
More informationEconomic and Social Council
UNITED NATIONS Economic and Social Council Distr. GENERAL TRANS/WP.29/78/Rev.1/Amend.2 16 April 1999 ENGLISH Original: ENGLISH and FRENCH ECONOMIC COMMISSION FOR EUROPE INLAND TRANSPORT COMMITTEE Working
More informationInstallation and Operation Instructions RINGFEDER Type 2050 AM RINGFEDER Type 2050 AP
Installation and Operation Instructions RINGFEDER Type 2050 AM RINGFEDER Type 2050 AP 22.10.2003 10069125 Type 2050 AM General RINGFEDER Type 2050 AM, part no.: 14994532 RINGFEDER Type 2050 AP, part no.:
More informationMP440E39T/P-HM ( CURSOR )
N. : DT 1 0 TECHNICAL DESCRIPTIONS MP4E39T/P-HM ( CURSOR ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any
More informationDate 2017/01/27 In Progress Quote no. ZA Version 0 Technical Specification
Technical Specification FMX 440 HP 6*4 Tractor High chassis height with T-ride Transport operation Rough road conditions Long distance transport cycle Predominantly flat topography Ambient temperature
More informationMP400E35HT ( CURSOR )
N. : DT 190 064 TECHNICAL DESCRIPTIONS MP400E35HT ( CURSOR ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at
More information65C14G CCS EURO VI (F1C 3.0l) CNG
MCA 2014 65C14G CCS EURO VI (F1C 3.0l) CNG The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time Engineering
More informationTECHNICAL SPECIFICATIONS - New Boxer L1 Summary - 09/2016
TECHNICAL SPECIFICATIONS - New Boxer L1 S&S S&S S&S Versions : L1H1 - L1H2 GVW : 2800 / 3000 / 3300 / 3500 (5) / 4000 (5) DW10FU Euro6 DW10FU Euro6 DW10FU Euro6 DW10FU Euro6 DW10FU Euro6 DW10FU Euro6 Max.
More informationO SL. BPW Original spare parts Air suspensions series O / SL / AL BPW BERGISCHE ACHSEN BPW ORIGINAL SPARE PARTS. BPW Original spare parts
BPW riginal spare parts Air suspensions // BPW BERGISCHE ACHSEN BPW riginal spare parts Air suspensions series / / BPW RIGIN SPARE PARTS BPW riginal spare parts Air suspensions Contents Page Air suspension
More informationCODE 4 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS (STATIC TEST)
CODE 4 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS (STATIC TEST) 1 TABLE OF CONTENTS 1. DEFINITIONS... 3 1.1 Agricultural and forestry tractors...
More informationDATA. icargo) Product. Application. Purpose. Function. Knorr-Bremse s intelligent axle loading system, icargo, is designed to work on:
Commercial Vehicle Systems Product DATA Doc. No. Y09 (EN - Rev. 00) January 0 Application Knorr-Bremse s intelligent axle loading system,, is designed to work on: Semi-trailers with two to five axles Centre-axle
More informationML140E24W ( EURO 3 - NEW )
TECHNICAL DESCRIPTION ML140E4W ( EURO 3 - NEW ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify or change specification at any time. 1 ML140E4W
More informationMH260E30Y/PS-RSU ( CURSOR (RSU) (E30) )
N. : DT 610 04 TECHNICAL DESCRIPTIONS MH60E30Y/PS-RSU ( CURSOR + 0375 (RSU)+ 06494 (E30) ) The information in this literature is intended to be of a general nature only. Iveco reserve the right to modify
More informationFORD TRUCKS 4142M EURO6
FORD TRUCKS 4142M EURO6 3292 2540 1490 2050 3050 1330 940 5100 8860 Basic Features Vehicle Type Mixer Emission Euro 6 Cabin Type 8x4 Day Cab Wheelbase (mm) 5100 Engine Type Ecotorq 12,7 liters Displacement
More informationLIFTING CHARTS - Conventional Truck Cranes AMERICAN MODEL TON CAPACITY
LIFTING CHARTS - Conventional Truck Cranes AMERICAN MODEL - 125 TON CAPACITY 1 LIFT RATINGS With Tubular Hammerhead and "K-F-L-M" Counterweight (34,000 lbs.) Min 11 82.8-91090 250000 250000 47 10 12 81.3-87730
More informationDRAFT VTS. Approved for Racing
Vehicle Manufacturer: Year and Model: DRAFT VTS Approved for Racing This draft of the listed vehicle s VTS is posted with the specifications that we currently have for the vehicle. If a specification is
More informationNQR Crew Cab Diesel Specifications
Model GVWR WB Engine Model/Displacement HP (Gross) Torque (Gross) Equipment Transmission Steering Front Axle Suspension GAWR Rear Axle Suspension GAWR Wheels Tires Brakes Fuel Tank Frame Cab Equipment
More informationRS 413 SUPPLEMENTAL RESTRAINT SYSTEM CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL
413 REMOVAL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. PRECAUTION Be sure to read "PRECAUTION" thoroughly before servicing (See page -1). 2.
More informationCRUISEMASTER XT COIL - INDEPENDENT SUSPENSION SYSTEMS
VEHICLE COMPONENTS PTY LTD A.B.N. 44 010 033 762 352b Bilsen Rd Geebung QLD 4034 PO Box 14 VIRGINIA BC QLD 4014 Accounts: 07 3624 3810 Fax 07 3624 3888 accounts@ Sales: 07 3624 3800 Fax 07 3624 3888 sales@
More informationCARROSSERIE LEMEIRE BVBA (00 32 (0) ) PRESENTATION SEMI-TRAILER KG WITH EU TYPE APPROVAL E6*2007/46*0105*00
(00 32 (0)52 47 05 48) PRESENTATION SEMI-TRAILER 18.500KG WITH EU TYPE APPROVAL E6*2007/46*0105*00 Page 1 PRESENTATION SEMI-TRAILER 18.500kg LEMEIRE S.A.18500 (LOW FLOOR CHASSIS with disc brakes) E6*2007/46*0105*00
More informationProduct Catalogue. Version 8.0. Section. Arvin Meritor (ROR) Axle Components
Product Catalogue Section E Version 8.0 Arvin Meritor (ROR) Axle Components PRODUCT CATALOGUE 8.0 ArvinMeritor (ROR) Axle Type Capacity Wheel Fixing 300-0003-1D0F5 TM/T25010/ZMX 11,690 kg 10 stud M22 x
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationAT 20-3 PICK & CARRY CRANE. At View thousands of Crane Specifications on FreeCraneSpecs.com. Features: AT 20-3
PICK & CARRY CRANE DATASHEET - METRIC At 20-3 Features: 20 tonne at 1.4 m radius 1.60 tonne at 15.8 m radius 17 m maximum hook height Single line 4.2 tonne Hook block (4 parts) capacity 16.8 tonne CONTENTS
More informationCOMMISSION REGULATION (EU)
10.11.2010 Official Journal of the European Union L 292/21 COMMISSION REGULATION (EU) No 1009/2010 of 9 November 2010 concerning type-approval requirements for wheel guards of certain motor vehicles and
More informationFront Suspension. Front Suspension Component Layout. NOTE: Without Dynamic Response version shown
Published: Jan 25, 2005 Front Suspension Front Suspension Component Layout NOTE: Without Dynamic Response version shown 1 Flanged bolt (Upper arm forward bush) 2 Bush - forward (Upper arm) Page 1 of 9
More information65C15 CCS MCA 2014 EURO 5+ (F1C
MCA 2014 65C15 CCS EURO 5+ (F1C 3.0l) The information in this literature is intended to be of a general nature only. Iveco reserves the right to modify or change specification at any time Engineering Profile
More informationAT Tonne Lifting Capacity Pick & Carry Crane Datasheet Metric. Features: AT 22
22 Tonne Lifting Capacity Pick & Carry Crane Datasheet Metric Features: 22 tonne at 1.4 m radius 1.7 tonne at 15.8 m radius 17 m maximum hook height Hook block (4 parts) capacity 16.8 tonne Single line
More informationComponents for hydraulic equipment. General. Actions before starting a new hydraulic system
General General It is possible to order components from the factory for operating hydraulic equipment. The following components are available: Control Hydraulic oil tank with pressure limiting valve Hydraulic
More informationTHE HINO 700 DESIGNED TO
THE HINO 00 DESIGNED TO KEEP YOU UCKING NO MATTER HOW LONG AND HARD THE ROAD IS AHEAD, YOU CAN REST ASSURED THAT THE HINO 00 RANGE, WITH PROVEN TECHNOGY AND RELIABILITY BEYOND QUESTION, WILL BE WITH YOU
More informationSchedule PART 1: PRELIMINARY
Roads and Maritime Services Class 1 Special Purpose Vehicles Notice 2014 I, Peter Duncan, Chief Executive Roads and Maritime Services (RMS), pursuant to Clause 12 of the Road Transport (Mass, Loading and
More informationSCANIA. Body Components and Front & Rear Lighting. Edition 1
SCANIA Body Components and Front & Rear Lighting Edition 1 Introduction Bison Parts are one of the UK fastest growing Commercial Vehicle specialists of steering, suspension and body components. All products
More information1009 WIPER MOTOR COVER ASSEMBLY 1010 WIPER ARM 1011 PARALLEL WIPER ARM. WIPER BLADE mm mm mm mm 1016 WASHER BOTTLE
WIPERS HEAVY DUTY WIPER MOTOR 999 TM.81-12v 80 degrees 1000 TM.83-12v 90 degrees 1001 TM.84-24v 90 degrees 1002 TM.86.12-12v 110 degrees WIPER MOTOR 1003 TM.64.1469-12v 90 degrees 1004 TM.64.1467-12v 90
More informationISO 5700 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 5700 Fourth edition 2006-11-15 Tractors for agriculture and forestry Roll-over protective structures (ROPS) Static test method and acceptance conditions Tracteurs agricoles et
More informationJCB FASTRAC 3200/3230
FULLY SUSPENDED WITH 4 WHEEL ABS DISC BRAKING (TERRITORY DEPENDENT). JCB SMOOTHSHIFT TRANSMISSION. STATIC DIMENSIONS A B G H C D E F STATIC DIMENSIONS Tyres 540/65R30 495/70R24 A Height to exhaust 3.15
More information