L441/ L444 Four-Post High-Capacity Open- and Closed-Front Alignment Lifts

Transcription

1 Four-Post Lift Family L441/ L444 Four-Post High-Capacity Open- and Closed-Front Alignment Lifts

2 Four-Post lifts Available in long or short, open or closed configurations. Two Swing Air Jacks 4 Raise vehicles off runways Integrated Louvered Ramps 4 9,000-lb. capacity 4 Prevent wheel spin 4 More effective than diamond tread or abrasive strips Flush Slipplates 4 Wheelbases up to Tethered pins secure plates on basic models Two Movable Work Steps Extra-Wide Runways 18,000-lb secure positions 4 Accommodate wide vehicles 4 Lightweight design 22½ 4 Rub rails for drive-on safety Other

3 Air Line Kit Louvered Locks Control Unit 4 Convenient power for air tools at front and rear 4 16 lock heights ensure runways are level 4 Long-life galvanized cables 4 Easy-to-use console 4 Powerful 3-hp motor Pins and Pulleys 4 Large diameter iron pulleys with teflon bearings ensure long life 4 Chrome-plated pins Model L451T-IS shown Umbilical Covering Capacity NEW! Open-Front Available on Any Configuration Lift 18,000 Pounds! 4 Best in class! 4 Allows easy access to adjustment points and jacks on long- and standard-length runway racks 4 Strong and flexible 4 Protects air and hydraulic lines from damage

4 PowerSlide edition saves time and hassle! PowerSlide Locking System PowerSlide slipplates Secure slipplates with a single button. The technician no longer has to struggle to remove and replace slipplate pins for every alignment. PowerSlide control Push-button locks or unlocks the slipplates and turnplates. PowerSlide turnplates Save time by eliminating struggle with turnplate pins. Trips Around the Car with PowerSlide Yesterday's technology VS. 1 Mount targets 2 Jack vehicle and compensate sensors 3 Lower leveling legs (if equipped) 8 Trips 4 5 Remove slipplate and turnplate pins Make adjustments Only 3 Trips! Remove targets Replace slipplate and turnplate pins Raise leveling legs (if equipped) Models L451T-PS, L454T-PS

5 FIA/Inflation Station edition maximizes productivity! Fully Integrated Alignment with Inflation Station and PowerSlide FIA console Controls PowerSlide and Inflation Station features. Automatic locking Turnplates and slipplates lock and unlock at the right time. Locks automatically during lift descent. Model L451T-IS shown FIA allows WinAlign aligners to control lift features for ultimate productivity.* Integrated inflation reels Automatically fills or bleeds each tire. Record air pressure Printouts record starting and final pressure. Models L451T-IS, L454T-IS * Alignment console sold separately.

6 Swing Air Jacks Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations. The heavy-duty Swing Air Jack has a capacity of 9,000 lbs. (4,082 kg) and combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles ,000-lb. Capacity Swing Air Jack AlignLights system Hunter s AlignLights lighting system provides an efficient light source underneath the vehicle. OPTIONAL AlignLights is powered by the main lift power source and requires no additional or exposed electrical cords. AlignLights automatically turns off when the lift is lowered to the floor and turns on when the lift is raised AlignLights system for four-post lifts Turnplates All L451T and L454T models will ship with the most appropriate turnplates. When making a substitution, any of the following turnplates may be used PowerSlide turnplates with automatic bridges Two stainless steel turnplates for camera-sensor systems PowerSlide turnplates without automatic bridges Two stainless steel turnplates for conventional-sensor systems Stainless steel turnplate kit Two stainless steel Delrin-ball turnplates and bolt-on guide strips Low-friction stainless steel turnplate kit Two stainless steel Torlon ball turnplates and bolt-on guide strips Powder-coated turnplate kit Two powder-coated, Delrin-ball turnplates and bolt-on guide strips. Integrated bridge lowers and raises as plates are locked, making rolling compensation a snap. Air-operated control system ties directly into PowerSlide lifts ( shown).

7 Standard-length specifications Max. vehicle weight Max. wheelbase General service Two-wheel alignment* Four-wheel alignment Min. four-wheel alignment Max. lifting height Alignment height Minimum height Overall height Tread width Motor Air Min. inside Max. outside * Long wheelbase vehicles may require jacking compensation. Models Open-front L451JT L451T-PS L451T-IS Closed-front L454JT L454T-PS L454T-IS 18,000 lbs. (8164 kg) 193 in. (4902 mm) 177 in. (4496 mm) 158 in. (4013 mm) 88 in. (2235 mm) 75 in. (1905 mm) Any of 16 lock positions 8.75 in. (222 mm) 98 in. (2489 mm) 40 in. (1016 mm) 85 in. (2159 mm) 3 hp, VAC, 60 Hz, 1 ph psi ( bar) Standard-length runways with (2) 9,000-lb. swing air jacks and stainless steel turnplates Standard-length runways with (2) 9,000-lb. swing air jacks and PowerSlide slipplates and turnplates Standard-length runways with (2) 9,000-lb. swing air jacks, PowerSlide slipplates and turnplates, Inflation Station, and FIA L /4 (210 mm) 31 BY 31 (787 mm BY 787 mm) OF JOINTS IN CONCRETE (located under both front post baseplates) /4 (5747 mm) 28 5/8 (727 mm) 20 1/2 BY 20 1/2 (521 mm BY 521 mm) OF JOINTS IN CONCRETE (located under both rear post baseplates) 31 1/2 (768 mm) L451 plan view /8 (4658 mm) RECOMMENDED BAY WIDTH 22 1/2 (572 mm) 12-3/8 (3667 mm) ROOM FOR ALIGNMENT CONSOLE HAWKEYE AND PRONTO SYSTEMS HAVE SPACE REQUIREMENTS IN FRONT OF THE LIFT THAT MUST BE MET, REFER TO APPROPRIATE SENSOR SITE REQUIREMENTS. 28 1/8 (714 mm) 9-9 3/8 (2981 mm) 40 (1016 mm) /16 (3535 mm) /16 (3015 mm) RUNWAY LENGTH: 18-3 (5563 mm) 4 (102 mm) L451 and L454 elevation view JOINT OVERALL LENGTH: /4 (6648 mm) JOINT 6 3 (1905 mm) MAXIMUM HEIGHT RECOMMENDED BAY LENGTH (For Lift with HE421 Camera Sensor) Floor-Mounted Sensors (FM, ML, LC or FM) Refer to 6292-T Typical /4 (8439 mm) Specified Range /2 to /4 (8649 mm to 7601 mm) For HE421CM: add 5 (127 mm) Refer to 6291-T For HE421WM: Spec Range is expanded. Refer to 6290-T 8 2 (2489 mm) 13 0 ( mm) MINIMUM CEILING HEIGHT Standard equipment Stainless steel turnplates (PowerSlide turnplates on PS and IS models) Flush-mounted, full-floating slipplates (PowerSlide slipplates on PS and IS models) Louvered ramps with built-in wheel stops Front wheel stops Two wheel chocks Two movable work steps Built-in, full-length jack rails Built-in rub rails Built-in air line kit Options Ramp Extension Kit (for low-clearance vehicles) Ramp Extension Kit (for extremely low-clearance vehicles or high-floor-slope situation) Because of continuing technological advances, specifications, models and options are subject to change without notice.

8 Extended-length specifications Max. vehicle weight 18,000 lbs. (8164 kg) Max. wheelbase General service 227 in. (5766 mm) Two-wheel alignment* 211 in. (5360 mm) Four-wheel alignment 158 in. (4013 mm) Min. four-wheel alignment 88 in. (2235 mm) Max. lifting height 75 (1905 mm) Alignment height Any of 16 lock positions Minimum height 8.75 in. (222 mm) Overall height 98 in. (2489 mm) Tread width Min. inside 40 in. (1016 mm) Motor Air Max. outside * Long wheelbase vehicles may require jacking compensation. Models Open-front Closed-front 85 in. (2159 mm) 3 hp, VAC, 60 Hz, 1 ph psi ( bar) L451L 31 BY 31 (787 mm BY 787 mm) OF JOINTS IN CONCRETE (located under both front post baseplates) L451L plan view ** /8 (4658 mm) RECOMMENDED BAY WIDTH 12-3/8 (3667 mm) ROOM FOR ALIGNMENT CONSOLE HAWKEYE AND PRONTO SYSTEMS HAVE SPACE REQUIREMENTS IN FRONT OF THE LIFT THAT MUST BE MET, REFER TO APPROPRIATE SENSOR SITE REQUIREMENTS. JOINT RECOMMENDED BAY LENGTH (For Lift with HE421 Camera Sensor) L451LJT L451LT-PS L451LT-IS L454LJT L454LT-PS L454LT-IS Standard and optional equipment Identical to L451 and L454 Lift Racks. Extended-length runways with (2) 9,000-lb. swing air jacks and stainless steel turnplates Extended-length runways with (2) 9,000-lb. swing air jacks and PowerSlide slipplates and turnplates Extended-length runways with (2) 9,000-lb. swing air jacks, PowerSlide slipplates and turnplates, Inflation Station, and FIA /4 (6572 mm) 28 5/8 (727 mm) 20 1/2 BY 20 1/2 (521 mm BY 521 mm) OF JOINTS IN CONCRETE (located under both rear post baseplates) 22 1/2 (572 mm) 28 1/8 (714 mm) 9-9 3/8 (2981 mm) 40 (1016 mm) /16 (3535 mm) /16 (3015 mm) RUNWAY LENGTH: /2 (6236 mm) OVERALL LENGTH: /4 (7474 mm) Floor-Mounted Sensors (FM, ML, LC or FM) Refer to 6292-T Typical /4 (9265 mm) Specified Range 31-3/4 to /4 (9468 mm to 8426 mm) For HE421CM: add 5 (127 mm) Refer to 6291-T For HE421WM: Spec Range is expanded. Refer to 6290-T Because of continuing technological advances, specifications, models and options are subject to change without notice. 31 1/2 (768 mm) 4 (102 mm) JOINT Be sure to check out other Hunter literature for more quality products from Hunter Engineering. ** See previous page for elevation view 1214B Copyright 2014, Hunter Engineering Company Form 6020-T, 12/14 Supersedes 6020-T, 10/14