Fabricators of polished stainless steel components for Hotrods and Customs. CATALOG

Transcription

1 Fabricators of polished stainless steel components for Hotrods and Customs. CATALOG

2 PAGE 2 TO ORDER CALL: TABLE OF CONTENTS MOLDINGS...3 RUNNING BOARD STRIP KITS...5 NERF BARS...6 CHIN BARS AND BUMPERS...10 HOOD SIDE VENTS...12 AIR CLEANERS...13

3 MCMILLAN ROD & CUSTOM PAGE 3 HALF ROUND SOLID STAINLESS STEEL MOLDINGS Moldings are available in 1/4, 3/8, 1/2, 5/8 and 3/4 wide. These moldings have a multitude of possibilities for your vehicle s interior and/or exterior. Moldings are half round solid stainless steel and sold by the linear foot. The moldings are machined from solid, type 304 stainless steel and polished to a mirror finish. Call for quote or lay out your pattern full size, mark where you want the studs, include shape of ends, roll it up, insert into a shipping tube and mail it to us. Below are options for end configurations. Diagonal is also available. Bullet (Pointed) Rolled Round Straight The studs are either 6-32 (used on the 1/4 molding) or 8-32 (used on 3/8 and up). The 8-32 stud is shown below on ½ molding. Studs are 3/4 long in stainless steel and installed with a stud welding process. Mounting studs are recommended for door panels and applications outside of your ride and are $5 each.

4 PAGE 4 TO ORDER CALL: MOLDINGS 3/4 half round...$25/foot 5/8 half round...$23/foot 1/2 half round...$18-$21/foot (See below) Up to 3 feet is $21/foot 3-10 is $20/foot is $19/foot Over 20 is $18/foot 1/2 half round, BALL MILLED...call for a quote 3/8 half round...$24/foot 1/4 half round...$23/foot LOW PROFILE MOLDINGS McMillan Rod and Custom low profile moldings offer a lower height profile than there standard half round moldings. The low profile moldings are solid, type 304 stainless steel and polished to a mirror finish. Options for end configurations include bullet (pointed), rolled, round, diagonal and straight. Mounting studs are recommended for exterior applications. Recommended studs are an 8-32 x ¾ and are $5 each. The cost is by the linear foot: 1/2 (5/32 thick) = $20/foot 3/4 (3/16 thick) = $25/foot 1 (1/4 thick) = $30/foot 1 1/4 (1/4 thick) = $35/foot

5 MCMILLAN ROD & CUSTOM PAGE 5 RUNNING BOARD STRIP KITS Standard Universal Kit is made from type 304 stainless steel half round strips and polished to a mirror finish. Comes in 1/2 ($435) or 5/8 ($495) wide and includes (2) 42 and (4) 36. Three studs are installed on each strip with your choice of bullet (pointed) or rounded ends. Short Running Board Kit comes in 1/2 ($395) or 5/8 ($435) wide and includes (2) 36 and (4) 32 with 3 studs installed on each strip. (These fit shorter running boards including a 32 Ford.) *Other lengths and widths are available. Call for pricing

6 PAGE 6 TO ORDER CALL: NERF BARS All of our nerf bars are made from 3/4 solid stainless. The mounting bracket is 2 x10 x 3/16 stainless. The entire piece is ground and polished to a mirror finish and sold as a set of two. 8 DOUBLE BEND NERF BARS $150 These are our best sellers. The vertical bar is 8 tall. 10 DOUBLE BEND NERF BARS $160 Same as the above only the vertical bar is 10 tall.

7 MCMILLAN ROD & CUSTOM PAGE 7 8 OR 10 DOUBLE BEND NERF BARS WITH 20 DEGREE BRACKETS $165/$175 While built specifically for Ford Model A s, 32 s, and 33/34 Fords, these nerfs can be used on the front of many streetrods having frame horns that curve down. The mounting brackets have a 20 degree bend in them to keep the vertical bar square to the ground. V-NERF BARS $140 Vertical bar is 8 tall and bent to a V shape.

8 PAGE 8 TO ORDER CALL: GULLWING NERF BARS $160 Vertical bar is 10 tall. BUMPERETTES $215/$230 Bumperettes are 12 wide and made from our ¾ moldings and are available in straight or 20 degree brackets. SIDE NERF BARS STARTING AT $350 These are sprint car style side nerf bars, built from solid 3/4 type 304 stainless steel to your specifications and polished to a mirror finish.

9 MCMILLAN ROD & CUSTOM PAGE /1934 FORD FLAT AND DRILLED NERF BARS $225 Built from 3/8 thick type 304 stainless steel, these nerf bars are contoured to fit the downward arc of the front frame horns. Each nerf bar is precision cut with a water jet and then polished by hand to a mirror finish. Nerfs come without the mounting holes drilled but if you would like, we can drill them at no extra charge. Comes as a set of two. 8 OR 10 CHEVROLET NERF BARS $185/$195 These are built specifically for early Chevrolets. They are available in 8 or 10 double bend versions with 9/16 threads, allowing them to be threaded into the frame rails. Built from solid type 304 stainless steel and polished to a mirror finish. They come as a set of two complete with jam nuts. While originally designed for early Chevy s they also work well in other applications like the 36 Ford pictured below.

10 PAGE 10 TO ORDER CALL: CHIN BARS AND BUMPERS 1932 FORD DOUBLE CHIN BAR WITH OR WITHOUT V8 $330/$310 Built from solid 3/4 diameter, type 304 stainless steel and polished to a mirror like finish. This chin bar offers a new look, and an alternative to the traditional straight or shaped spreader bar while maintaining the traditional look of a 32. Also available for model A s and pinched frames by special order. 1933/1934 FORD SINGLE CHIN BAR $305 Built specifically for a 1933/34 Ford, it utilizes our 10 nerf bars with 20 degree brackets and joined by a horizontal stainless bar following the contour of the body. TIG welded, ground, and polished to a mirror finish. 1933/1934 FORD REAR BUMPER $425 Built from high quality, solid type 304 stainless steel and polished to a mirror like finish. The horizontal bar is built from 3/4 solid round. Brackets are our popular sleeve style that allows 2 way adjustments for a better fit.

11 MCMILLAN ROD & CUSTOM PAGE FORD SINGLE CHIN BAR $290 Built from high quality, solid type 304 stainless steel and polished to a mirror like finish. We use our 10 double bend nerf bars with a horizontal bar built from 3/4 solid round FORD DOUBLE CHIN BAR $365 The two horizontal bars are made from 3/4 solid round with our V nerf bars. This may fit other makes of cars FORD SINGLE CHIN BAR WITHOUT NERF BARS $325 This bar is made from 3/4 solid round stainless steel and designed to fit cars with filled bumper bracket holes. Our sleeve type brackets allow for maximum adjustability.

12 PAGE 12 TO ORDER CALL: CUSTOM BUMPERS Be it our design or yours, we will work with you to give your project a look you want while staying within your budget. HOOD SIDE VENTS Precision cut from 16 gauge stainless steel, these are fully functional vents and are designed to bolt on. Sold in pairs and available in single ($99/pair), double ($149/pair), or triple ($249/pair) designs. These also work well for interior accents and saddle bag trim.

13 PAGE 13 TO ORDER CALL: AIR CLEANERS Our air cleaners are carefully formed from type 304 stainless steel, TIG welded, then polished to a mirror finish. These are our most popular designs, but we are happy to custom build to your specifications. Air Cleaners are made by special order. Please allow 3-4 weeks delivery. LOW PROFILE, INJECTION LOOK STRAIGHT STYLE $225 Built off our standard 14 long base, this unit features 8-2 flared stacks cut at a 45 degree angle to allow them to extend out parallel with the top of air cleaner. Comes complete with filter, filter base, & mounting screw. LOW PROFILE, INJECTION LOOK STREAMLINE STYLE $225 Also built off our standard 14 long base, this unit features 8-2 flared stacks cut at a 45 degree angle then evenly spaced and rotated to angle back giving the unit a streamlined look. Comes complete with filter, filter base, & mounting screw.

14 MCMILLAN ROD & CUSTOM PAGE 14 8 STACK INJECTION STYLE $425 This is a multi-stack injection looking air cleaner complete with filter element, mounting screw and base. Stacks are available in 6 or custom lengths for an additional fee. 8 STACK INJECTION STYLE STAGGERED $440 The 8-stack injection air cleaner is available with 8 tall staggered stacks also. If you want something different, this one is for you.

15 MCMILLAN ROD & CUSTOM PAGE 15 For more pictures, go to

16 DECIMAL EQUIVALENTS COURTESY OF MCMILLAN ROD & CUSTOM Jim & Carol Stauner McMillan Rod & Custom M243 M243 County Highway Road T T Marshfield, WI WI Phone: Phone: Cell: mcmillanrod@tznet.com