Freightliner Business Class M2 Cab and Chassis Vocational Reference Guide

Transcription

1 Section 1 Final Version October, 2009

2 Introduction This Cab and Chassis Modification Guide covers the following Freightliner vehicles: Business class m2 This manual is a source of basic information for body and equipment manufacturers, and dealers who install their products on Freightliner Medium and Heavy Duty truck chassis. Information on brake systems, electrical circuits, and chassis layout is included. This information is not intended for use by anyone who does not have substantial technical expertise in the design and manufacture of motor vehicles and motor vehicle equipment. The information in this manual is believed to be accurate to the best of our knowledge at the time this manual was approved for publication. The accuracy is not guaranteed. The information contained in the manual is general and nothing contained herein should be regarded as providing specific or comprehensive instructions for the completion of a particular vehicle, or as authorization by Freightliner Trucks of the assembly, modification, or alteration of any particular vehicle, whether delivered by Freightliner Trucks in complete or incomplete state of manufacture. Representations regarding the compliance of any Freightliner incomplete vehicle to any rule, regulation, or standard issued pursuant to the National Traffic and Motor Vehicle Safety Act or Canadian Motor Vehicle Safety Act is set forth only on the incomplete vehicle certificate accompanying each incomplete vehicle. Freightliner reserves the right to discontinue models or change specifications or designs at any time without notice and without incurring any obligation. Regulations such as those issued by the Federal Highway Administration or issued pursuant to the Occupational Safety and Health Act (OSHA), and/or state, provincial and local laws and regulations may require installation of additional equipment for the particular use intended for the vehicle. Nothing contained herein is to be construed as a representation that such equipment required for the particular use intended has been installed on the complete or incomplete vehicle. If clarification regarding content of this publication or technical information is required, such as a DXF file for a specific VIN, please call the Customer Application Engineering Department listed at If you choose to contact us by letter our address is: Freightliner Trucks Customer Application Engineering 2477 Deerfield Dr. Fort Mill, SC As a vehicle manufacturer, Freightliner neither approves nor disapproves truck chassis modifications or equipment installations because Freightliner cannot control the manufacturing techniques of the various body/ equipment builders. Page 1-1

3 A chassis cab manufactured by Freightliner Trucks is certified for compliance with the U.S. and Canadian Motor Vehicle Safety Standards as an incomplete vehicle which may be completed into a truck type vehicle. The vehicle certification is a requirement of the National Traffic and Motor Vehicle Safety Act (United States) and Canadian Motor Vehicle Safety Act (Canada). This manual provides general instructions and suggestions for the installation of bodies and equipment on Freightliner Medium and Heavy Truck chassis as well as general guidelines for modifications to Freightliner Medium and Heavy Trucks. Following these suggestions will contribute substantially to the longevity of the vehicle. The suggestions published in this manual are general in nature and assume that the facility workshop and workers performing the tasks of installation or modification use accepted shop practices and techniques. Freightliner does not assume any liability for damage(s) to persons or property caused by use of this publication. Modifications, alterations, and installations are the sole responsibility of those performing the work. ENGINE EXHAUST EMISSION CONTROL INFORMATION Title II of the Clean Air Act, as amended, requires vehicle manufacturers to supply the purchaser of a commercial vehicle with all the service and maintenance literature necessary to ensure the emission-related components function properly for the useful life period. The useful life period varies with fuel, vehicle type, and GVWR as defined by 40 CFR, Sections and In compliance with the provisions, the Driver s Manual and Maintenance Manual (workshop type) contain all the information required for the operation and maintenance of the factory-installed emission related components of your Freightliner Medium and Heavy Truck engine. The Environmental Protection Agency has certified each engine, thereby confirming it meets exhaust emission standards for the new engines. To be certain the emission related components function over the useful operation as designed, regular maintenance is necessary for these components. The required services and procedures are in the Required Vehicle Service and Maintenance Work section of the Driver s Manual. Emission, Noise and Safety The Emission Control Warranty covers a period of 50,000 miles or 5 years, whichever occurs first, for all heavy duty gasoline engines and heavy duty diesel engines under 19,500 lbs. GVWR. For all other heavy duty diesel engines, this warranty period is 100,000 miles or 5 years, whichever occurs first. The Emission Control Warranty does not cover repair or replacement of parts necessitated by the failure to use appropriate fuels and lubricants (listed in the Lubricants and Fluids section of the appropriate Engine Operations and Maintenance Manual), or the failure to properly maintain the emission related components. Maintenance must be performed at the intervals indicated in the Maintenance Categories and Intervals section of the Driver s Manual. If engine settings are not adhered to at maintenance inspections, or if improper modifications are made on emission related components, excessive exhaust emissions and engine or drivetrain damage may result. It is the vehicle owner s responsibility to be certain that no unauthorized adjustments or modifications are made to their truck(s). In addition, the Clean Air Act, as amended, prohibits any person engaged in the business of repairing, servicing, selling, leasing, or trading motor vehicles or motor vehicle engines, or who operates a fleet of motor vehicles, knowingly to remove or render inoperative any device or element of the design installed in a motor vehicle or a motor vehicle engine in compliance with the regulations under this Title following its sale and delivery to the ultimate purchaser. The Emission Certification label location for each engine is shown on the chart on page 1-8 of this manual. Page 1-2

4 FEDERAL REGULATIONS, EPA, PART 205; TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Part 205, Transportation Equipment Noise Emission Controls, requires the vehicle manufacturer to furnish, with each new vehicle, such written instructions for the proper maintenance, use, and repair of the vehicle by the ultimate purchaser, to provide reasonable assurance of the elimination or minimization of noise emission degradation throughout the life of the vehicle. In compliance with the law, this section provides these instructions to owners. Tampering Federal law prohibits the following acts or the causing thereof: The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. Among those acts presumed to constitute tampering are the acts listed below: Removing or rendering the exhaust system components inoperative Removing or rendering the engine speed governor inoperative to allow engine speed to exceed the manufacturer s specifications Replacing the fan with an unauthorized fan Removing the radiator shield Removing the noise shields or acoustical absorptive material Removing air induction system components Emission, Noise and Safety Noise Control Maintenance To maintain the noise control performance of your Freightliner vehicle, it must receive periodic inspections, maintenance, and service parts replacements. These services are included in the Maintenance Jobs section of the Driver s Manual and should be performed at every maintenance interval. Please contact your Freightliner truck dealer if further details on servicing noise related components or other parts of your vehicle are necessary. Page 1-3

5 INTERMEDIATE AND/OR FINAL STAGE MANUFACTURER RESPONSIBILITIES It is the responsibility of the intermediate and/or final stage manufacturer to comply with all applicable laws and regulations pertaining to the manufacture and certification of equipment installations and/or vehicle modifications at time of certification. The intermediate and/or final stage manufacturer is solely responsible for the final certification of the vehicle and for compliance with EPA noise emissions requirements and Federal Motor Vehicle Safety Standards in effect on the stated date of manufacture. The vehicle components listed below require special attention by the intermediate and/or final stage manufacturer: 1. No alteration or modification may be made to vehicle components forward of the rear cab wall unless they are approved component installations (such as air conditioning, radio, etc.) which are manufactured or endorsed by Freightliner. 2. The functional reliability and freedom of movement of all movable chassis components (e.g., axles, springs, driveshafts, steering systems, braking systems, gearshift linkages, exhaust systems, etc.) must not be impaired by the installation of bodies or accessory equipment. This applies to the vehicle at rest and under operation. 3. The frame top and bottom flanges must not be drilled, altered or damaged in any way. 4. The vehicle braking and steering systems are safety related components. Anyone making changes or modifications to any component of these systems must assume complete responsibility for that system and its operation. 5. The operational reliability, roadworthiness and driveability of the vehicle must not be impaired by body or accessory equipment installation. Emission, Noise and Safety If any vehicle modifications or equipment installations have been performed, we advise that to the extent these modifications or equipment installations adversely affect other vehicle components or vehicle performance, we will be unable to accept any product liability or claims under the vehicle warranty and any such adverse affects therefore become the sole responsibility of the person performing the modifications or equipment installations. Any manufacturer that makes material alterations to this incomplete vehicle during the process of manufacturing the complete vehicle should constantly recognize all the effects, either direct or indirect, on other components, assemblies, or systems caused by such alteration. No alterations should be made to the incomplete vehicle which either directly or indirectly results in any component, assembly or system being in noncompliance with any Emission Control Standard or Federal Motor Vehicle Safety Standard, or which would otherwise cause the vehicle to be or become defective or unsafe. Advice concerning compliance with the U.S. Motor Vehicle Safety Act standards and regulations should be obtained from your legal counsel, the National Highway Traffic Safety Administration, or Transport Canada, as applicable. Radio Frequency Interference RFI Devices that emit radio frequency (RF) energy, such as AM/FM radios and radio-controlled security systems, marketed for sale or use in the United States are subject to the rules and regulations of the Federal Communications Commission (FCC). 47 C.F.R. Parts 2 and 15. To insure continued compliance with the FCC s requirements, the owner, user, custom manufacturer, or service technician must not modify or change the RF device in a manner not expressly approved by Freightliner Truck Corporation. Such modifications could void the authority to operate the device. Page 1-4

6 Labels Noise Control Information A label stating compliance with U.S. Environmental Protection Agency Noise Emission Standards is attached to the left side door sill below the striker, for complete vehicles certified by Freightliner. Please consult the Maintenance Booklet supplied with each vehicle for cautionary information pertaining to compliance with Federal Regulation, EPA, Part 205: Transportation Equipment Noise Emission Standards. Vehicle Document Information Federal requirements regarding certification of compliance to Federal Motor Vehicle Safety Standards (FMVSS) for vehicles manufactured in two or more stages are contained in parts 567 and 568 of Title 49 of the code of Federal Regulations. The purpose of these regulations is to ensure that each completed motor vehicle will have a permanently affixed label certifying that such vehicle conforms to all applicable FMVSS in effect on the stated date of manufacture (see the following examples). The incomplete vehicle document, enclosed in an envelope, is in the cab when the vehicle is released from Freightliner Truck Corporation (see the following examples). Vehicle Emission Control Information Freightliner provides each complete and incomplete vehicle with a separate VEHICLE EMISSION CONTROL INFORMATION LABEL, identifiable by its part number and content, inside the cab. These are described on pages 1-2 and 1-7. Emission, Noise and Safety Page 1-5

7 Label Location and Attachment Requirements Freightliner Business Class M2 COMPONENT INFORMATION COMPONENT INFORMATION USE VEHICLE ID NUMBER WHEN ORDERING PARTS MANUFACTURED BY FREIGHTLINER TRUCK PLANT MOUNT HOLLY LLC MT. HOLLY, NORTH CAROLINA MODEL VEHICLE ID NO. MM106042S 1FVACXBS39HAE4952 BASE MODEL:M2106 CUSTOMER:P54442 DATE OF MFR. WHEELBASE 5/ ENGINE MODEL MAIN TRANS MOD FIRE PUMP MOD FRONT AXLE MOD 1ST INT AXLE MOD 2ND INT AXLE MOD 3RD INT AXLE MOD 4TH INT AXLE MOD 5TH INT AXLE MOD 6TH INT AXLE MOD REAR AXLE MOD PAINT MFR. PAINT NUMBER CUM ISC HP / 2000 RPM:2200 GOV ALLISON 3000 RDS AUTOMATIC TRANSMISSION AF ,000# FF KPI/3.74 DROP MERITOR RS ,000# R-SRS ELITE SS PAINT C CAB COLOR A: N0006EA WHITE ELITE SS ENGINE NO. TRANS NO. FIRE PUMP NO. FRONT AXLE NO. 1ST INT AXLE NO. 2ND INT AXLE NO. 3RD INT AXLE NO. 4TH INT AXLE NO. 5TH INT AXLE NO. 6TH INT AXLE NO. REAR AXLE NO. RATIO FOR COMPLETE PAINT INFORMATION SEE VEHICLE SPECIFICATION SHEET. L PART NO REV A A FOR One copy is in the Warranty Book and one copy is in the dash panel storage compartment Page 1-6

8 Label Location and Attachment Requirements VEHICLE NOISE EMISSION CONTROL INFORMATION (U.S. ONLY) VEHICLE NOISE EMISSION CONTROL INFORMATION FREIGHTLINER MT. HOLLY LLC DATE OF MANUFACTURE 5/08 THIS INCOMPLETE VEHICLE, AS DELIVERED BY FREIGHTLINER LLC, CONFORMS TO U.S. EPA REGULATIONS FOR NOISE EMISSION APPLICABLE TO MEDIUM AND HEAVY TRUCKS. IT IS THE RESPONSIBILITY OF THE FINAL STAGE MANUFACTURER TO COMPLETE THIS VEHICLE WHILE MAINTAINING CONFORMANCE TO 40 CFR PART 205, INCLUDING LABELING FOR COMPLIANCE (SEC ). Affixed to the left side door sill below striker INCOMPLETE VEHICLE THIS CHASSIS-CAB CONFORMS TO FEDERAL MOTOR VEHICLE SAFETY STANDARDS 101,102,103,104,106,107,111, ,105/121,124,205,206,207,208,209,210 & 302. CONFORMITY TO OTHER SAFETY STANDARDS APPLICABLE TO THIS VEHICLE WHEN COMPLETED IS NOT SUBSTANTIALLY AFFECTED BY THE DESIGN OF THE CHASSIS-CAB. TYPE: TRUCK MANUFACTURED BY VEHICLE ID NO. DATE OF MFR. GVWR-KG GVWR-LBS IF COMPLETED IN ACCORDANCE WITH INSTRUCTIONS IN THE INCOMPLETE VEHICLE DOCUMENT PURSUANT TO 49CFR,PART 568, THIS VEHICLE WILL CONFORM TO FMVSS 108. FREIGHTLINER MT. HOLLY LLC 2FZHCHBS68AY /08 14,686 33,000 FRONT AXLE FIRST INT AXLE SECOND INT AXLE THIRD INT AXLE FOURTH INT AXLE FIFTH INT AXLE SIXTH INT AXLE REAR AXLE GAWR-KGS GAWR-LBS TIRES RIMS KPA COLD PSI COLD "S INGLE/"D"UAL 5,443 12,000 11R22. 5(G) 22.5X S 9,525 21,000 11R22. 5(G) 22.5X D L PART NO REV A Affixed to the left side door sill Page 1-7

9 Label Location and Attachment Requirements TIRE AND RIM INFORMATION MAXIMUM GWR BY COMPONENT (KG) LB COMPONENET FRONT AXLE FIRST INT AXLE SECOND INT AXLE THIRD INT AXLE FOURTH INT AXLE FIFTH INT AXLE SIXTH INT AXLE REAR AXLE AXLE ( 5443) ( 9525) SUSPENSION ( 5443) ( 9525) TIRES ( 5601) (10596) RIMS ( 6622) (13426) HUBS/SPOKES ( 6350) (11793) BRAKES ( 6032) ( 9979) STEERING ( 6032) COMPONENT GVWR CHASSIS ENG/TRANS (36288) TH WHL PARK BRAKE AXLE VIN 1FVACXB539HAE4952 PART NO REV A Affixed to the right side door sill Engine Exhaust Emission Compliance Certification is contained on the label installed on each engine assembly by the engine manufacturer. Location of the label for each engine manufacturer is shown below. MANUFACTURER ENGINE LOCATION Cummins All Front Gear Housing on Fuel Pump Side Mercedes-Benz All Valve Cover Page 1-8

10 Federal Motor Vehicle Safety Standards (FMVSS) & Canadian Motor Vehicle Safety Standards (CMVSS) The purpose of this information and the following summarized text is to assist you in interpreting the Federal Motor Vehicle Safety Standards (FMVSS) and Canadian Motor Vehicle Safety Standards (CMVSS) for vehicles and how they apply to the sale of Freightliner Medium and Heavy Duty trucks sold in the U.S. and Canada. Vehicles sold for delivery in the U.S. are manufactured by Freightliner Trucks for completion in compliance with the U.S. Federal Motor Vehicle Safety Standards. The Canadian Motor Vehicle Safety Standards will apply to vehicles sold in Canada. The FMVSS and CMVSS regulations control the manufacture and sale of motor vehicles and their usage. Other laws apply to the application and use of vehicles. Owners or operators using vehicles are responsible for those vehicles meeting certain legal requirements. The MVSS laws, by contrast, put the burden of obeying the law on the manufacturer, dealer, or body manufacturer who sells the completed vehicle to the end user. For this reason, it is important that all concerned parties review information carefully to ensure compliance with the MVSS laws and related safety standards. It is recommended that dealers and others concerned review this information with their legal counsel. No modification or addition to the vehicle can be made which causes noncompliance with any FMVSS or CMVSS, as applicable, as certified by Freightliner Truck Corporation. Freightliner LISTS EACH STANDARD WITH A DESCRIPTION OF CERTIFICATION. FMVSS 101 / CMVSS 101 This vehicle, when completed, will conform to FMVSS / CMVSS No. 101, Control Location Identification and Illumination, if no alterations are made to the vehicle controls including their location, means of identification and method of illumination. Vehicle and system control, including but not limited to: steering wheel horn control transmission shift lever ignition switch headlight switch tail light turn signal control illumination intensity rheostat windshield wiper/washer control driver's sun visor automatic vehicle speed system high beam heating system controls HAZARD warning flasher clearance light control hand throttle identification light control service brake accelerator clutch winshield defrosting and defogging system contol FMVSS 102 / CMVSS 102 This vehicle, when complete, will conform to FMVSS / CMVSS No. 102, Transmission Shift Lever Sequence, Starter Interlock and Transmission Braking Effect, if no alterations are made to the shift pattern display(s). If the vehicle is equipped with an automatic transmission, the vehicle will conform if no alterations are made in the transmission, transmission controls, connecting linkages, and cables, starting motor, starting motor wiring or plumbing, neutral safety switch and ignition or equivalent switch and related wiring, and shift lever position identifications. Page 1-9

11 Federal Motor Vehicle Safety Standards (FMVSS) & Canadian Motor Vehicle Safety Standards (CMVSS) FMVSS 103 / CMVSS 103 This vehicle, when complete, will conform to FMVSS / CMVSS No. 103, Windshield Defrosting and Defogging Systems, if no alterations are made in the windshield defrosting and defogging systems, controls, wiring, plumbing and air flow to the windshield. Windshield and Defrosting Systems, including but not limited to: WINDSHIELD ASSEMBLY HEATER AND DEFROSTER ASSEMBLY - INCLUDING MOTOR AND BLOWER HEATER AND WATER HOSES AND HOSE ASSEMBLIES AND ROUTING DEFROSTER NOZZLES DEFROSTER DUCTS HEATER CONTROLS CHASSIS AND INSTRUMENT WIRING HARNESS BLOWER MOTOR RESISTOR FMVSS 104 / CMVSS 104 This vehicle, when complete, will conform to FMVSS / CMVSS No. 104, Windshield Wiping and Washing Systems, if no alterations are made in the windshield wiper arms, blades, washer, controls, wiring, or plumbing. Windshield Wiping and Washing Systems, including but not limited to: WINDSHIELD ASSEMBLY WINDSHIELD WIPER ARM ASSEMBLY WINDSHIELD WIPER BLADE ASSEMBLY HEATER CORE WATER VALVE ENGINE WATER OUTLET THERMOSTAT WINDSHIELD WIPER WINDSHIELD WASHER FLUID RESERVOIR WASHER RESERVOIR CAP WINDSHIELD WIPER LINKAGE ASSEMBLY WINDSHIELD WASHER NOZZLE WINDSHIELD WIPER AND WASHER CONTROL CHASSIS WIRING HARNESS WINDSHIELD WIPER AND WASHER MOTOR AND PUMP ASSEMBLY FMVSS 105 / CMVSS 105 This vehicle, when complete, will conform to FMVSS / CMVSS No. 105, Hydraulic Braking System Components and Fittings, if it does not exceed any of the gross axle or gross vehicle weight ratings and if no alterations or changes are made in, to the anti-lock system components or electrical circuitry (if present); tire size and wheelbase. FMVSS 106 / CMVSS 106 This vehicle, when complete, will conform to FMVSS / CMVSS No. 106, Brake Hoses, if no alterations are made to the air or hydraulic brake hoses, brake hose assemblies, and brake hose fittings including the labeling on these components. FMVSS 107 / CMVSS 107 This vehicle, when complete, will conform to FMVSS / CMVSS No. 107, Reflecting Surfaces, if no alterations are made in the windshield wiper arms or blades, in the inside windshield mouldings, and in the horn ring and hub of the steering wheel assembly. If an inside rearview mirror is installed by any subsequent manufacturer, it shall be the responsibility of that manufacturer to ensure that the specular gloss of the surface of the inside rearview mirror frame and mounting bracket conforms to the requirements of this standard. FMVSS 108 / CMVSS 108 For Truck Tractor This vehicle, when manufactured as a truck tractor, will conform to FMVSS / CMVSS No. 108, Lamps, Reflective Devices, and Associated Equipment, if no alterations are made to any associated items supplied on the vehicle and no obstructions are installed which limit visibility of any item. For Truck Conformity with FMVSS / CMVSS 108, Lamps, Reflective Devices, and Associated Equipment, is not substantially determined by the design of this chassis cab. The manufacturer makes no representation to conformity with the standard. Page 1-10

12 Federal Motor Vehicle Safety Standards (FMVSS) & Canadian Motor Vehicle Safety Standards (CMVSS) FMVSS 111 / CMVSS 111 This vehicle, when complete, will conform to FMVSS / CMVSS No. 111, Rearview Mirrors, if no alterations are made to mirrors, mounts, locations, or cab structure and no obstructions are installed which limit usage. FMVSS 113 / CMVSS 113 For Conventional Model Vehicles This vehicle, when complete, will conform to FMVSS / CMVSS No. 113, if no alterations are made in the Hood Latch System, including the attachments for the hood latches. hood front reinforcement sub-assembly hood lock assembly For Cab Forward or COE Vehicles This standard is not applicable to this vehicle. hood lock conrol cable assembly FMVSS 115 / CMVSS 115 This vehicle, when complete, will conform to FMVSS / CMVSS No. 115, Vehicle Identification Number, if no alterations are made to the identification number. VIN coding information for Freightliner trucks is shown on pages 1-15 and 1-16 of this manual. FMVSS 116 / CMVSS 116 This vehicle, when complete, will conform to FMVSS / CMVSS No. 116, Motor Vehicle Brake Fluid, if no changes are made that affect the physical or chemical properties of the brake fluid. Use only heavy duty fluid, DOT 3, in the hydraulic brake system if additional fluid is needed. FMVSS 120 / CMVSS 120 This vehicle, when complete, will conform to FMVSS / CMVSS No. 120, Tire Selection and Rims for Motor Vehicles Other Than Passenger Cars, if no changes are made to the tires, rims, or labeling. FMVSS 121 / CMVSS 121 This vehicle, when complete, will conform to FMVSS / CMVSS No. 121, Air Brake System, if it does not exceed any of the gross axle or gross vehicle weight ratings, and if no alterations or changes are made in, or affect the air system components, or circuitry (if present); electric wire circuit or components associated with the above, tire size and wheelbase. FMVSS 124 / CMVSS 124 This vehicle, when complete, will conform to FMVSS / CMVSS No. 124, Accelerator Control System, if no alterations are made to any components of the throttle control or fuel metering system. FMVSS 205 / CMVSS 205 This vehicle, when complete, will conform to FMVSS / CMVSS No. 205, Glazing Materials, if no alterations are made in the glazing material installed in the windshield and windows of the cab. FMVSS 206 / CMVSS 206 This vehicle, when complete, will conform to FMVSS / CMVSS No. 206, Door Locks and Door Retention Components, if no alterations are made in the door assembly, door latches, door striker assemblies, door hinges, door locks, door latch posts, door hinge posts, and supporting cab structure. FMVSS 207 / CMVSS 207 This vehicle, when complete, will conform to FMVSS / CMVSS No. 207, Seating Systems, if no alterations are made to the seats, seat adjusters, restraining devices, release and adjustment controls, seat risers, and supports, and the cab floor and supporting structure. Page 1-11

13 Federal Motor Vehicle Safety Standards (FMVSS) & Canadian Motor Vehicle Safety Standards (CMVSS) FMVSS 208 / CMVSS 208 This vehicle, when complete, will conform to FMVSS / CMVSS No. 208, Occupant Crash Protection, if no change is made in the number of designated occupants seating positions provided, and if no alterations are made in the cab and supporting structure, cab underbody, seat belt assemblies, seat belt anchorages, seats, and seating anchorages. FMVSS 209 / CMVSS 209 This vehicle, when complete, will conform to FMVSS / CMVSS No. 209, Seat Belt Assemblies, if no alterations are made in the seat belt assemblies, seat belt anchorages and attachments, and the cab structure to which the anchorages are attached. FMVSS 210 / CMVSS 210 This vehicle, when complete, will conform to FMVSS / CMVSS No. 210, Seat Belt Assembly Anchorages, if no additional occupant seats or seat belt assembly anchorages are added and if no alterations are made which affect the function, physical, or mechanical properties, environmental or vital clearance of the components, assemblies or systems identified below: Seat Belt Systems, including but not limited to: FMVSS 302 / CMVSS 302 This vehicle, when complete, will conform to FMVSS / CMVSS No. 302, Flammability of Interior Materials, if no alterations are made to the materials, including the surface material and padding or cushioning used in the interior of the vehicle s occupant compartment including but not limited to the following components: seat cushions, seat backs, seat belts, arm rests, all trim panels including door, front, rear, and side panels, compartment shelves, floor covering, headlining, sun visors, curtains, shades, engine compartment cover, mattress covers, and other interior materials, including padding that is designed to absorb energy on contact by occupants in the event of a crash. If the intermediate or final stage manufacturer installs any of the aforementioned items, those items must also meet the requirements of this standard. Summary The final stage manufacturer must complete the vehicle in such a manner that it conforms to all standards in effect on the date of manufacture by Freightliner Truck Corporation, the date of final completion or a date between those two dates. seat assemblies seat belt routing seat position and/or adjustment capability floor plan assemblies seat belt assemblies Seat belt anchorage brackets and/or reinforcement Page 1-12

14 Used in the U.S. National Traffic and Motor Vehicle Safety Act or Regulations Thereunder Assembler means a manufacturer engaged in the business of altering vehicles that bear the National Safety Mark. Definitions of Terms of the completed vehicle, that requires further manufacturing operations, other than the addition of readily attachable components, such as mirrors or tire and rim assemblies, or minor finishing operations such as painting, to become a completed vehicle. Chassis Cab means an incomplete vehicle, with a completed occupant compartment, that requires only the addition of cargo-carrying, work-performing or load-bearing components to perform its intended functions. Completed Vehicle means a vehicle that requires no further manufacturing operations to perform its intended function, other than the addition of readily attachable components, such as mirrors or tire and rim assemblies, or minor finishing operations such as painting. Dealer means any person who is engaged in the sale and distribution of new motor vehicles or motor vehicle equipment primarily to purchasers who in good faith purchase any such vehicle or equipment for purposes other than resale. Final-Stage Manufacturer means a person who performs such manufacturing operations on an incomplete vehicle that it becomes a completed vehicle. Gross Axle Weight Rating (GAWR) means the value specified by the vehicle manufacturer as the load carrying capacity of a single axle system as measured at the tire-ground interfaces. Gross Vehicle Weight Rating (GVWR) means the value specified by the vehicle manufacturer as the loaded weight of a single vehicle. Incomplete Vehicle means an assemblage consisting, as a minimum, of frame and chassis structure, power train, steering system, suspension system, and braking system, to the extent that those systems are to be part Manufacturer means any person engaged in the manufacturing or assembling of motor vehicles or motor vehicle equipment, including any person importing motor vehicles or motor vehicle equipment for resale. Truck means a motor vehicle with motive power, except a trailer, designed primarily for the transportation of property or special purpose equipment. Truck Tractor means a truck designed primarily for drawing other motor vehicles (semi trailers) and not so constructed as to carry a load other than a part of the weight of the vehicle and the load so drawn. Unloaded Vehicle Weight (UVW) means the weight of a vehicle with maximum capacity of all fluids necessary for operation of the vehicle, but without cargo, occupants, or accessories that are ordinarily removed from the vehicle when they are not in use. Vehicle Alterer as used in this book means a person who alters a vehicle that has previously been certified in accordance with Section or of Title 49 Code of Federal Regulations other than by the addition, substitution or removal of readily attachable components such as mirrors or tire and rim assemblies, or minor finishing operations such as painting, or who alters the vehicle in such a manner that its stated weight ratings are no longer valid, before the first purchase of the vehicle in good faith for purposes other than resale. Vehicle Capacity Mass means the rated cargo and luggage mass plus 150 pounds (70kg) multiplied by the designated seating capacity. Page 1-13

15 Freightliner VIN Coding Summary Sheet Example of VIN 1 F V A C X B S 3 9 H A Position Decoding Table A B C D E F G Serial Number World manufacturer identification Positions CODE MANUFACTURER Make Type 1FU Freightliner Corp. Freightliner Truck 1FV Freightliner Corp. Freightliner Incomplete Vehicle Chassis Position 4 CODE CONFIGURATION CHASSIS A 4 X 2 TRUCK B 4 X 2 TRUCK-TRACTOR D 4 X 4 TRUCK E 4 X 4 TRUCK-TRACTOR F 6 X 2 TRUCK G 6 X 2 TRUCK-TRACTOR H 6 X 4 TRUCK J 6 X 4 TRUCK-TRACTOR K 6 X 6 TRUCK L 6 X 6 TRUCK-TRACTOR X GLIDER GLIDER Model, cab, gvwr Position 5 6 CODE MODEL CAB GVWR Cs m2 100 CONVENTIONAL 14,001 X 16,000 LB CLASS 4 ct m2 100 CONVENTIONAL 16,001 X LB CLASS 5 CU m2 100 CONVENTIONAL 19,501 X 26,000 LB CLASS 6 CV m2 106 Medium Duty CONVENTIONAL 16,001 X 19,500 LB CLASS 5 CW m2 106 Medium Duty CONVENTIONAL 19,501 X 26,000 LB CLASS 6 CX m2 106 Medium Duty CONVENTIONAL 26,001 X 33,000 LB CLASS 7 CY m2 106 Medium Duty CONVENTIONAL 33,001 LBs and over CLASS 8 CZ m2 106 V Heavy Duty CONVENTIONAL 16,001 X 19,500 LB CLASS 5 C1 m2 106 V Heavy Duty CONVENTIONAL 19,501 X 26,000 LB CLASS 6 C2 m2 106 V Heavy Duty CONVENTIONAL 26,001 X 33,000 LB CLASS 7 C3 m2 106 V Heavy Duty CONVENTIONAL 33,001 LBs and over CLASS 8 C4 m2 112 Medium Duty CONVENTIONAL 26,001 X 33,000 LB CLASS 7 C5 m2 112 Medium Duty CONVENTIONAL 33,001 LBs and over CLASS 8 C6 m2 112 V Heavy Duty CONVENTIONAL 26,001 X 33,000 LB CLASS 7 C7 m2 112 V Heavy Duty CONVENTIONAL 33,001 LBs and over CLASS 8 C8 m2 106 Medium duty CONVENTIONAL 14,001 X 16,000 LB CLASS 4 F8 m2 106 medium glider CONVENTIONAL Glider FC m2 106 sport chassis CONVENTIONAL 16,001 X LB CLASS 5 FD m2 106 sport chassis CONVENTIONAL 19,501 X 26,000 LB CLASS 6 FE m2 106 sport chassis CONVENTIONAL 26,001 X 33,000 LB CLASS 7 Page 1-14

16 Freightliner VIN Coding Summary Sheet Example of VIN 2 F W P E C Y B 3 X A Position Decoding Table A B C D E F G Serial Number engine, brakes Position 7 8 CODE ENGINE FUEL DISPLACEMENT CONFIG BRAKES BS Cummins ISC Diesel 8.3 liter I-6 Air BT Cummins ISC Diesel 8.3 liter I-6 Hydraulic BU Cummins ISC Diesel 8.3 liter I-6 Air over Hyd Cn Mercedes-Benz MBE-900 Diesel 4.3 liter I-4 Air Cp Mercedes-Benz MBE-900 Diesel 4.3 liter I-4 Hydraulic Cr Mercedes-Benz MBE-900 Diesel 4.3 liter I-4 Air over Hyd cs Mercedes-Benz MBE-900 Diesel 6.4 liter I-6 Air ct Mercedes-Benz MBE-900 Diesel 6.4 liter I-6 Hydraulic cu Mercedes-Benz MBE-900 Diesel 6.4 liter I-6 Air over Hyd cv Mercedes-Benz MBE-4000 Diesel 12.8 liter I-6 Air cw Mercedes-Benz MBE-4000 Diesel 12.8 liter I-6 Hydraulic cx Mercedes-Benz MBE-4000 Diesel 12.8 liter I-6 Air over Hyd dg Mercedes-Benz MBE-900 Diesel 4.8 liter I-4 Air dh Mercedes-Benz MBE-900 Diesel 4.8 liter I-4 Hydraulic dj Mercedes-Benz MBE-900 Diesel 7.2 liter I-6 Air dk Mercedes-Benz MBE-900 Diesel 7.2 liter I-6 Hydraulic dt Cummins ISB Diesel 6.7 liter I-6 Air du Cummins ISB Diesel 6.7 liter I-6 Hydraulic Page 1-15

17 Freightliner VIN Coding Summary Sheet CHECK DIDGIT - Position 9 calculated from a mathmatical computation of all other vin characters Model Year Position 10 CODE model year A 2010 B 2011 C 2012 D 2013 build location - Position 11 code build location h mt. holly, nc d m-b mexico, santiago serial number - Position Sequentially assigned vehicle serial number Page 1-16

18 Rollover stability is an important factor which can influence the safe performance of the truck. Stability is influenced by many factors including chassis and body configuration, suspension, axle track width, tire size, tire pressure, etc. The cargo type and weight (payload), the body size, shape, and center of gravity height are particularly important. A guideline for rollover stability has been established in research conducted for the National Highway Traffic Safety Administration (HGTSA). This guideline is a value of lateral acceleration (0.35 g) corresponding to a certain speed, in a turn of a given radius, at which a truck will roll over. Freightliner has analyzed how this guideline relates to certain configurations and specifications which we produce for on-highway applications. Specialized configurations such as 4 x 4 and 6 x 6 all wheel drives, plus vehicles with loaded frame heights over 44 inches, are not covered. Freightliner vehicles rated up to 52,000 pounds GVWR, with Freightliner suspensions, conform to this guideline if the center of gravity of the combined body and maximum payload added to the Freightliner chassis is not higher than inches ( mm) above level ground for a vehicle/payload combination that loads the truck to its full gross vehicle weight (GVWR). For body and payload combinations that do not load the truck to 100% of its GVWR, the following graph can be used to determine the maximum allowable height of the combined body and payload center of gravity. These limits apply to payloads that are stable and laterally centered. If a vehicle configuration approaches or exceeds the limits shown on the graph, changes to the design of the vehicle should be considered. Two of the more effective modifications include specifying a wide track rear axle and, in certain cases, increasing the capacity of the rear suspension. The following graph shows that the use of a wide track rear axle results in a higher allowable CG for the combined body and payload. CG HEIGHT OF BODY PLUS PAYLOAD (Inches Above Ground) Vehicle Rollover Stability Guideline CG HEIGHT OF BODY PLUS PAYLOAD FOR ROLL THRESHOLD = 0.35 G WIDE REAR AXLE TRACK (78" Center to Center of Tire Pairs) NOMINAL REAR AXLE TRACK (72" Center to Center of Tire Pairs) PERCENT UTILIZATION OF RATED GVW [(Actual Vehicle Gross Weight) / (Total Max Rated Suspension Capacity)] * 100 NOTE: Conformance to this guideline does not ensure that a vehicle will be stable if safe operating practices are not followed. For example, excessive speed in turns or on nonlevel surfaces, unstable or offset loads, etc., can cause instability. Also, other factors influence handling and subjective feel such as suspension roll stiffness and steering geometry. These may influence drivers perceptions of whether a vehicle has satisfactory stability. IMPORTANT: Calculations of rollover stability are approximations. Confirmatory testing may be necessary in marginal circumstances. SAE J2180, a tilt table measurement procedure, can be utilized to more accurately establish rollover threshold. WARNING: Always consider rollover threshold when specifying a truck chassis and installing or modifying a body or major equipment. Otherwise, the vehicle could be unstable in curves or other steering maneuvers, possibly resulting in rollover and serious personal injury or death. Additional information can be obtained from Freightliner Truck Application Engineering at Page 1-17

19 SUSPENSION - FRONT AND REAR 1. No drilling or welding to the front axle I beam is permissible. Special equipment mounting or attaching brackets, requiring attachment to the front axle, may be clamped to axle I beams only. 2. Front or rear suspension member components should not be modified or relocated for any reason. AIR BRAKES Freightliner air brake equipped incomplete vehicle products to the extent completed, comply with Federal Motor Vehicle Safety Standard 121, Air Brake Systems. The statements contained in this section regarding FMVSS-121 compliance are accurate at the time of printing. However, these statements are not intended to replace the statements regarding FMVSS-121 in the Incomplete Vehicle Manual; consequently, that manual should be consulted for compliance conditions. Following are components and characteristics of the completed vehicle which are critical to overall performance of air braked vehicles. These items should be carefully considered in ordering a vehicle as well as planning vehicle completion by a subsequent stage manufacturer(s) to insure compliance (final certification) of the completed vehicle to FMVSS-121, as well as completed vehicle integrity. Center of Gravity The vertical center of gravity of the completed vehicle has a direct effect on the vehicle s stopping distance capability. As the vertical center of gravity increases or the wheelbase decreases, additional weight is transferred to the front axle during a stop, affecting the stopping distance. The Heavy Truck Incomplete Vehicle Document specifies that Trucks and Buses completed from chassis cabs and chassis cowls shall have center of gravity height/ wheelbase ratios of 0.50 or less when loaded to a weight not exceeding GVWR* distributed proportionately to, but not exceeding GAWR s* or, as measured from the ground to the center of gravity of the vehicle/payload combination, the center of gravity height must not exceed 70 inches on single rear axle vehicles or 75 inches on tandem rear axle vehicles, whichever is less. Truck Body and Special Equipment Installation Precautions As a guide, the vertical center of gravity height of the incomplete vehicle, as manufactured by Freightliner Trucks, may be assumed to be the distance from the ground to the top of the frame side rail measured at the longitudinal midpoint of the vehicle in the unladen condition for single axle vehicles and laden condition for tandem axle vehicles. The frame rail height may be calculated from the chassis diagrams in this publication. Also, if you are measuring an unloaded chassis, you may assume the loaded frame rail height to be two inches lower than the bare chassis. Vehicles completed as trucks could require a vertical center of gravity lower than the recommendations above based on the stability considerations of certain vocational body and/ or usage situations. The above recommendations consider only vehicle brake performance. If higher vertical center-of-gravity limitations are required for a specific vocational body or application, contact your Freightliner District Sales Manager, or submit all chassis specifications along with body and payload information in a request for advice to: Freightliner Trucks Customer Application Engineering 2477 Deerfield Dr. Ft. Mill, SC NOTE: *GVWR and GAWR s as indicated on the cover of the Incomplete Vehicle Document provided with the records. Page 1-18

20 ENGINE AND ENGINE ACCESSORIES Modifications to the engine-driven air compressor, the drive speed ratio of the air compressor, or the engine-governed RPM will directly affect the ability of the compressor to build up air brake system pressure. FMVSS-121 contains specific air brake system pressure build-up performance requirements which could be adversely affected by any of these modifications. Consequently, the representation as to conformity to FMVSS-121 provided in the Incomplete Vehicle Manual is conditional upon none of the above-mentioned modifications being made. Air-Functioned Accessories FMVSS-121 contains a pressure build-up performance requirement which states that the system pressure must build up from 85 to 100 psi in a specific time period under certain conditions. Therefore, the addition of any accessory or its associated plumbing which increases the volume of air subject to the build-up requirement will increase the build-up time and may affect compliance with FMVSS-121. The representation as to conformity of the completed vehicle to FMVSS-121 provided in the Incomplete Vehicle Document has the following conditions for air-operated accessories and associated plumbing added to a vehicle by a subsequent stage manufacturer. No connections are made into (1) the air line tubing or fittings for the parking brake system, (2) the rear axle emergency system (modulated spring brake system), (3) the air supply and signal lines to the rear chassis relay valve(s) or (4) the air delivery lines to the front axle brakes and quick release valve. No connections are made between the check valve and the reservoir port for air supply. Additional reservoir volume must be added with tag or pusher axles, etc. Added volume must be equal to 12 times the added brake chambers rated volume. Each added reservoir shall be capable of withstanding an internal hydrostatic pressure of five times the compressor cutout pressure or 500 psi, whichever is greater, for 10 minutes. Truck Body and Special Equipment Installation Precautions Air for a pneumatic accessory should be sourced directly from an air reservoir. If an unused reservoir tap is not available, fittings added to the system at the reservoir must not restrict air flow to any existing air lines. GENERAL GUIDELINES FOR CONNECTING TO AIR SYSTEM The following are to be observed when adding air accessories. Do s The secondary air system is the preferred connection point for auxiliary devices. However, the primary system may be used if connections to the secondary system are impractical. Connect to supply lines at or between service tanks and in-cab control valves only. Add drain valves to additional reservoirs. Add pressure protection valves with a minimum rating of 55 psi for all added non-brake components Do Not s Do not connect to lines between air tanks and relay valve. Do not connect to lines between foot valve and relay valves or front delivery to brakes (Delivery System). Do not connect to spring brake lines or lines to emergency system spring brake valve. Do not connect to supply tank or connecting lines. Do not tap between check valve at supply line to air reservoir and reservoir port. Above guidelines apply to accessories only and should not be used for additional axle installations. Page 1-19

21 Adding Brake Air Dryer Tanks and/or Additional Air Reservoirs Brake air dryer tanks, where used, must meet the requirements of FMVSS-121 for reservoirs. They must have drain valves which can be operated manually. Relocation of Air Reservoirs Relocation of air reservoirs may be accomplished with the following precautions: All air lines and fittings are to be same size and material as original equipment with no kinking or air passage restrictions. Original air reservoir volumes are not to be reduced. Relocation of an air reservoir in a direction farther from the relay valve will require testing for compliance to FMVSS-121 -S5.3.3 and S5.3.4 Brake Application and Release Timing. Relocation of Relay Valve The relay valve may be relocated, if necessary, subject to the following restrictions: Minor relocation without revisions to air lines would be acceptable provided no lines are kinked or restricted in size. Routing of all hoses must provide clearance to axle, air lines, and other components, as well as ensure adequate hose length throughout all axle articulations. Minor length changes and routings of air lines at the rear axle to air chambers are acceptable. All fittings, hoses and air lines utilized for the modified installation must be of the same size and specification of the original equipment on the chassis, and installations must be free of kinks and restrictions. All fasteners must be equivalent to the specifications of the original equipment. A vehicle final-stage manufacturer or alterer who chooses to lengthen or shorten wheelbases on vehicles with FMVSS-121 air brakes should note that he is responsible for the modification, including revisions to the frame, driveline, wiring, plumbing, suspension, etc. The vehicle final-stage manufacturer or alterer must also certify the vehicle for compliance to FMVSS-121. Truck Body and Special Equipment Installation Precautions Vehicle wheelbase modifiers should note the following conditions and instructions: It is possible to shorten the wheelbase without adversely affecting air brake timing. However, tractors should not be shortened to a wheelbase shorter than the shortest offered by Freightliner Trucks with the same front and rear axle combination. Trucks, also, should not be shortened to a wheelbase shorter than the shortest offered by Freightliner Truck Corporation with the same front and rear axle combination for truck service. It is possible to lengthen the wheelbase up to the maximum wheelbase offered by Freightliner Truck Corporation as a regular production option for that truck series without affecting air brake timing compliance. The plumbing for the modified wheelbase should be the same as used by Freightliner in regular production of that longer wheelbase. This will require following the air brake schematic as shown in this Freightliner Cab and Chassis Vocational Reference Guide and may require the addition of a quick release valve on the rear axle or to the relay valve signal line. Vehicle GVWR and GAWR s The representation as to conformity of the complete vehicle to FMVSS-121 provided in the Incomplete Vehicle Document is conditioned on the GVWR and the GAWR s of the completed vehicle being identical to the ratings designated on the front cover of the Incomplete Vehicle Document for the vehicle. The brake system on each air braked incomplete vehicle manufactured by Freightliner Trucks is designed to comply with FMVSS-121 when loaded to a specific completed vehicle GVWR distributed proportionate to specific GAWR s. Revised vehicle GVWR or GAWR s, or the addition of axles to the vehicle, will change loading conditions and may adversely affect compliance to FMVSS-121. Page 1-20

22 Wheelbase Modifications Persons intending to lengthen or shorten a vehicle frame and wheelbase are encouraged to contact Freightliner Truck Application Engineering at for precautionary recommendations prior to modification. Any deviation from the original vehicle specification will become the responsibility of the subsequent stage manufacturer or installer. All fittings, hoses and air lines used on vehicles with modified wheelbases must be the same size and specification as the original equipment on the chassis. There must be no kinking, added elbows, or other air passage restrictions. Any lengthening or splicing of wires should be in accordance with procedures described in the Electrical Section on page 1-24 of this section. Tires Tire size and tire traction characteristics (rubber composition and tread design) significantly affect vehicle stopping capability on both wet and dry road surfaces. Changes in tire size may also require the reprogramming of the vehicle ABS computer. Call Freightliner Truck Application Engineering at for additional information. Consequently, the representation as to conformity of the completed vehicle to FMVSS-121 provided in the Incomplete Vehicle Document is conditioned on the tires on the completed vehicle being those installed by Freightliner Truck Corporation on the incomplete vehicle. If the incomplete vehicle is fitted with temporary transportation tires, Freightliner Truck Corporation makes no representation as to conformity with FMVSS-121. Truck Body and Special Equipment Installation Precautions Suspension and Steering The representation as to conformity of the completed vehicle to FMVSS-121 provided in the Incomplete Vehicle Manual is conditioned on no modifications being made by a subsequent stage manufacturer(s) to the suspension or steering systems of an incomplete vehicle which could in any way adversely affect vehicle or related brake system performance. Addition of Tag or Pusher Axles - Air Braked Vehicles Any deviation from the original vehicle specification will become the responsibility of the subsequent stage manufacturer or installer. If tag and pusher axles are added to Freightliner FMVSS-121 air brake truck chassis, the following conditions must be met for each installation: Because of the added chamber volume accompanying the brakes on the added axle, the reservoir volume will have to be re-evaluated to ensure compliance to the 12X chamber volume criterion for reservoirs. Added reservoirs must meet the requirements of FMVSS-121. It is the responsibility of the subsequent installer to ensure that brake actuation and release timing and compressor capacity requirements of the modified system are met. Physical testing may be required by the installer if a body of correlation data to support an engineering analysis is absent. Engineering analysis should be made to ensure that the service, emergency and parking brake capabilities equal or exceed those of the base vehicle. If not, performance tests may be necessary to ensure compliance to the requirements of FMVSS-121. Engineering analysis to determine compliance and any added certification or incomplete vehicle labels should use the GAWR s and GVWR of the base vehicle, showing the added axle at its rated GAWR. Page 1-21