TABLES. Caterpillar Performance Handbook Edition 44

Transcription

1 TABLES Caterpillar Performance Handbook Edition Caterpillar. All Rights Reserved. CAT, CATERPILLAR, BUILT FOR IT, their respective logos, Caterpillar Yellow, the Power Edge trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

2 TABLES SWELL VOIDS LOAD FACTORS SWELL (%) VOIDS (%) LOAD FACTOR BUCKET FILL FACTORS Loose Material Fill Factor Mixed Moist Aggregates % Uniform Aggregates up to 3 mm (1/8") % 3 mm-9 mm (1/8"-3/8") % 12 mm-20 mm (1/2"-3/4") % 24 mm (1") and over % Blasted Rock Well Blasted 80-95%0 Average Blasted % Poorly Blasted % Other Rock Dirt Mixtures % Moist Loam % Soil, Boulders, Roots % Cemented Materials % NOTE: Loader bucket fill factors are affected by bucket penetration, breakout force, rackback angle, bucket profile and ground engaging tools such as bucket teeth or bolt-on replaceable cutting edges. NOTE: For bucket fill factors for hydraulic excavators, see bucket payloads in the hydraulic excavator section. TYPICAL ROLLING RESISTANCE FACTORS Various tire sizes and inflation pressures will greatly reduce or increase the rolling resistance. The values in this table are approxi mate, particularly for the track and track + tire machines. These values can be used for estimating purposes when specific performance information on particular equipment and given soil conditions is not available. See Mining and Earthmov ing Section for more detail. ROLLING RESISTANCE, PERCENT* Tires Track Track UNDERFOOTING Bias Radial ** +Tires A very hard, smooth roadway, con crete, cold asphalt or dirt surface, no penetration or flexing.. 1.5%* 1.2% 0% 1.0% A hard, smooth, stabilized surfaced roadway without penetration under load, watered, maintained % 1.7% 0% 1.2% A firm, smooth, rolling roadway with dirt or light surfacing, flex ing slightly under load or undulating, main tained fairly regularly, watered % 2.5% 0% 1.8% A dirt roadway, rutted or flexing under load, little maintenance, no water, 25 mm (1") tire penetration or flexing % 4.0% 0% 2.4% A dirt roadway, rutted or flexing under load, little maintenance, no water, 50 mm (2") tire penetration or flexing % 5.0% 0% 3.0% Rutted dirt roadway, soft under travel, no maintenance, no stabilization, 100 mm (4") tire penetration or flexing % 8.0% 0% 4.8% Loose sand or gravel % 10.0% 2% 7.0% Rutted dirt roadway, soft under travel, no maintenance, no stabilization, 200 mm (8") tire penetration and flexing % 14.0% 5% 10.0% Very soft, muddy, rutted roadway, 300 mm (12") tire penetration, no flexing % 20.0% 8% 15.0% **Percent of combined machine weight. ** Assumes drag load has been subtracted to give Drawbar Pull for good to moderate conditions. Some resistance added for very soft conditions. ANGLE OF REPOSE OF VARIOUS MATERIALS ANGLE BETWEEN HORIZONTAL AND SLOPE OF HEAPED PILE MATERIAL Ratio Degrees Coal, industrial :1 1.3: Common earth, Dry :1 1.0: Common earth, Moist :1 1.0: Common earth, Wet :1 1.7: Gravel, Round to angular :1 0.9: Gravel, Sand & clay :1 1.4: Sand, Dry :1 1.7: Sand, Moist :1 1.0: Sand, Wet :1 1.0: Edition

3 ROUND REINFORCED CONCRETE PIPE APPROXIMATE WEIGHT PER FOOT INSIDE DIAMETER WEIGHT PER FT. mm ft/in kg lb " " " '9" '0" '3" '6" '9" '0" '6" '0" '6" '0" '6" '0" '6" '0" '6" '0" '6" '0" NOTE: Table courtesy of American Concrete Pipe Assn. COEFFICIENT OF TRACTION FACTORS TRACTION FACTORS MATERIAL Rubber Tires Tracks Concrete Clay loam, dry Clay loam, wet Rutted clay loam Dry sand Wet sand Quarry pit Gravel road (loose not hard) Packed snow Ice Semi-skeleton shoes Firm earth Loose earth Coal, stockpiled NOTE: The elevated sprocket design Track-type Tractors (D11T, D10T2, D9T, D9R, D8T, and D8R), with their suspended undercarriage, provide up to 15% more efficient tractive effort than rigid tracked Track-type Tractors. SPEED CONVERSION km/h Equivalents in m/min MPH Equivalents in FPM km/h m/min km/h m/min mph fpm mph fpm NOTE: Since 1 km/h equals NOTE: Since 1 mph equals 88 fpm 16.7 m/min ( ), to ( ), to interpolate inter polate add 1.67 m/min add 8.8 fpm for every for each 0.1 km/h. 0.1 mph. 1 mph = 26.9 m/min. BEARING POWERS BEARING POWER MATERIAL Bar lb/ in 2 Metric t/m 2 U.S. tons/ft 2 Rock (semi- shattered) Rock (solid) Clay, dry Clay, medium dry Clay, soft Gravel, cemented Sand, compact dry Sand, clean dry Quicksand & alluvial soil AGRICULTURAL COMMODITIES CONVERSION FACTORS lb kg Metric Ton 1 Bushel of Corn* Bushel of Soybean* Bushel of Oats* Bushel of Wheat* Bale of Cotton metric ton of Corn Bushels* 1 metric ton of Soybean Bushels* 1 metric ton of Oats Bushels* 1 metric ton of Wheat Bushels* 1 metric ton of Cotton 4.61 Bales * Bushel is a volume measurement, 1 Bushel = liters = 9.31 U.S. Gallons. In the agricultural mercantile exchange, the Bushel is widely used for grains as weight. For the above weights, the market assumes a standard density for each type of grain Edition 44

4 CURVE SUPERELEVATION IN PERCENT GRADE, TO PROVIDE NO LATERAL TIRE FORCE Negotiating curves can generate high lateral tire forces. These forces contribute to high tire wear and ply separation. Superelevating the curve helps eliminate these forces. The amount of superelevation depends on the curve s radius and the speed at which it is negotiated. The following table is a guide for providing the superelevation necessary to eliminate lateral forces. Superelevated turns present a danger when slippery. For this reason, curves superelevated over 10% should be used with caution. Unless the proper speed is maintained, matching the elevation of the curve, a vehicle may slide off of the lower edge of the roadway. Superelevated curves should be maintained in good tractive conditions. Speed Speed Speed Speed Speed Speed Speed Speed TURN RADIUS 16 km/h 24 km/h 32 km/h 40 km/h 48 km/h 56 km/h 64 km/h 72 km/h m ft 10 mph 15 mph 20 mph 25 mph 30 mph 35 mph 40 mph 45 mph % 30% % 15% 27% % 10% 18% 28% % 8% 13% 21% 30% % 5% 9% 14% 20% 27% % 3% 5% 8% 12% 16% 21% 27% % 2% 4% 6% 9% 12% 15% 19% % 2% 3% 4% 6% 8% 11% 14% MAXIMUM SPEED ON CURVES FOR VARIOUS SUPERELEVATION GRADES WITH A 0.20 LATERAL COEFFICIENT OF TRACTION Another approach to superelevated curves is to determine the safe speed for negotiating a turn at a certain lateral tire force. In general, a 20% lateral coefficient of traction is conservative for all but ice and slippery conditions, making table values safe to use for most applications. The following table shows maximum speed with various superelevations to maintain a 0.20 lateral coefficient of traction. A transition section may be necessary at higher speeds when entering or departing from a superelevated turn. 5% Superelevation 10% Superelevation TURN RADIUS Flat Curve m ft km/h mph km/h mph km/h mph Edition

5 LOOSE BANK LOAD WEIGHT* OF MATERIALS kg/m 3 lb/yd 3 kg/m 3 lb/yd 3 FACTORS Basalt Bauxite, Kaolin Caliche Carnotite, uranium ore Cinders Clay Natural bed Clay Dry Clay Wet Clay & gravel Dry Clay & gravel Wet Coal Anthracite, Raw Coal Anthracite, Washed Coal Ash, Bituminous Coal Coal Bituminous, Raw Coal Bituminous, Washed Decomposed rock 75% Rock, 25% Earth % Rock, 50% Earth % Rock, 75% Earth Earth Dry packed Earth Wet excavated Earth Loam Granite Broken Gravel Pitrun Gravel Dry Gravel Dry 6-50 mm (1/4"-2") Gravel Wet 6-50 mm (1/4"-2") Gypsum Broken Gypsum Crushed Hematite, iron ore, high grade Limestone Broken Limestone Crushed Magnetite, iron ore Pyrite, iron ore Sand Dry, loose Sand Damp Sand Wet Sand & clay Loose Sand & clay Compacted Sand & gravel Dry Sand & gravel Wet Sandstone Shale Slag Broken Snow Dry Snow Wet Stone Crushed Taconite Top Soil Taprock Broken Wood Chips** **Varies with moisture content, grain size, degree of compaction, etc. Tests must be made to determine exact material characteristics. ** Weights of commercially important wood species can be found in the last pages of the Logging & Forest Products section. To obtain wood weights use the following equations: lb/yd 3 = (lb/ft 3 ).4 27 kg/m 3 = (kg/m 3 ) Edition 44

6 ALTITUDE DERATION PERCENT FLYWHEEL HORSEPOWER AVAILABLE AT SPECIFIED ALTITUDES m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') D3K XL D3K LGP D4K XL D4K LGP D5K XL D5K LGP D5N XL & LGP D6K XL & LGP N/A N/A D6N XL & LGP N/A N/A D6N XL & LGP** D6G D6G Series 2 XL D6G Series 2 LGP D6R D6R Series 3 (All) D6T (Tier 4 Interim/Stage IIIB) D7E D7G *100* *100* *100* D7G Series D7R Series 2 (All) D8R D8T D9R D9T U.S. EPA Tier 4 Final D9T Tier 3 equivalent NACD Std. Altitude D9T Tier 3 equivalent NACD High Altitude D9T EU Stage IIIA equivalent D9T Tier 2 equivalent D10T2 Tier 2 equivalent *** D10T2 Tier 4 Final*** D11T/D11T CD Tier 2 equivalent**** D11T/D11T CD Tier 4 Final**** H STD M H STD H STD M ****Refer to Captive Vehicle Fuel Specifications microfiche at your local dealer. ****Information not available at time of printing. ****In forward gears. ****D11T High altitude arrangement available. 30 Edition

7 ALTITUDE DERATION (Continued) m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') 140H STD M * * 160H STD M * * 14M * 16M M * * 216B B D N/A N/A 242D N/A N/A 246D N/A N/A 257D N/A N/A 259D N/A N/A 262D N/A N/A 272D N/A N/A 272D XHP N/A N/A 277D N/A N/A 279D N/A N/A 287D N/A N/A 289D N/A N/A 299D N/A N/A 299D XHP N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 303 SR/CR N/A N/A N/A 303E (Japan) N/A N/A 303.5E N/A N/A 304 CR N/A N/A N/A 304E N/A N/A 305 SR/CR N/A N/A N/A 305E N/A N/A 305.5E N/A N/A 307C (4M40) * * * * 308C SR/CR * * * * 308E N/A N/A 311D LRR * * * 312D/312D L** * * * 312D/312D L*** * * * 313C SR/CR D CR/314D LCR * * * 315D L** * * * 315D L*** * * * 319D L/319 D LN * * * ***Information not available at time of printing. ***Japan Sourced. ***France Sourced Edition 44

8 ALTITUDE DERATION (Continued) m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') M313C N/A N/A M315C N/A N/A M316C * * * * * * M318C N/A N/A M322C N/A N/A M313D * * * * * * M315D * * * * * * M316D M318D M322D D/320D RR/323D * 320D L/320D LRR/323D L * 320C N * 321D LCR * 322C D L C LN C D LCR D L D LN C D L D LN D D L C L C/385C L C FS F (NA) N/A N/A 416E (Turbo) N/A N/A 422F (Turbo) N/A N/A 428F (Turbo) N/A N/A 432F (Turbo) N/A N/A 434F (Turbo) N/A N/A 444F (Turbo) N/A N/A 428F (Electronic) N/A N/A 432F (Electronic) N/A N/A 434F (Electronic) N/A N/A 444F (Electronic) N/A N/A 416F (Electronic) N/A N/A 420F/420F IT (Electronic) N/A N/A 430F/430F IT (Electronic) N/A N/A 450E/F (Electronic) N/A N/A *Information not available at time of printing. 30 Edition

9 ALTITUDE DERATION (Continued) m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') Forest Products: 320C FM ** 320D FM ** 322C FM D FM C FM D FM C FM ** 330D FM D FM ** ** ** ** ** ** ** ** ** ** ** ** 522 ** ** ** ** ** ** 525B ** ** ** ** ** ** ** ** ** ** ** ** 535B ** ** ** ** ** ** 541 ** ** ** ** ** ** 545 ** ** ** ** ** ** 551 ** ** ** ** ** ** 552 ** ** ** ** ** ** PL N/A N/A 572R2 100* 100* 100* PL PL H H H Tractor H Scraper G G Tractor G Scraper *100* *100* G Tractor G Scraper **Refer to Captive Vehicle Fuel Specifications microfiche at your local dealer. **Information not available at time of printing. EUI engine Automatic altitude deration. NOTE: Contact factory for deration estimates based upon site specific temperatures and altitudes for altitude range of 3800 to 4600 m (12,500 to 15,000 ft) Edition 44

10 ALTITUDE DERATION (Continued) m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') 770G Tier 4 Final G G Tier 4 Final G E G Tier 4 Final G G Tier 4 Final G D G Tier 4 Final G C D D 1900 HP D 2100 HP D 2100 HP D D HAA F F HAA F F F HAA F2 * * * * * * 824H * * * * * * 834H * * * * * * 844H K F2 * * * * * * 825H * * * * * * 816F2 * * * * * * 826H * * * * * * 836H * * * * * * 901C (Japan) N/A N/A 902C (Japan) N/A N/A 903C (Japan) N/A N/A N/A N/A 906H N/A N/A N/A N/A 907H N/A N/A N/A N/A 908H N/A N/A 914G/IT14G N/A N/A * 1 EPA Tier 1 Capable * 2 EPA Tier 2 Certified **Information not available at time of printing. Automatic altitude deration. NOTE: Contact factory for deration estimates based upon site specific temperatures and altitudes for altitude range of 3800 to 4600 m (12,500 to 15,000 ft). 30 Edition

11 ALTITUDE DERATION (Continued) m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') 924K K K K K K K K H N/A 962H N/A 966H K XE M H M H K H K K D ** ** 994F ** ** 994H ** ** 939C * * 953D N/A N/A 963D N/A N/A 973C TH220B N/A N/A TH330B N/A N/A TH360B N/A N/A TH560B N/A N/A TH580B N/A N/A PM-565B * * * RM-250C RM-350B * * * AP-800C N/A N/A AP-900B * * * * * * AP-1000B AP-650B AP-655C * * AP-1050B AP-1055B **Information not available at time of printing. **Automatically derates 3%/300 m (1000 ft) above 3000 m (10,000 ft). NOTE: The 950K, 962K, 966K, 972K and 980K are Tier 4 Interim/Stage IIIB machines and only available in North America and Europe. Contact your local Cat dealer for product availability. NOTE: The 950H, 962H, 966H, 972H and 980H are not available in all regions. Contact your local Cat dealer for product availability Edition 44

12 ALTITUDE DERATION (Continued) m m m m m m MODEL (0-2500') ( ') ( ') ( ,000') (10,000-12,500') (12,500-15,000') BG N/A N/A BG-240C BG-260C BG-225C N/A N/A BG-245C BG-2455C BG N/A N/A CS-323C N/A N/A CS-423E CS-433E CS-533E CS-563E CS-573E CS-583E CS-663E * * CS-683E CP-323C CP-433E CP-533E CP-563E CP-573E CP-583E CP-663E * * CB-214E CB-224E/CB-225E CB-334E CB-335E CB-434D N/A N/A CB-534D/CB-534D XW CB-634D PS-150C N/A N/A PS-360B N/A N/A PF-300B N/A N/A PS-300B N/A N/A R1300G R1600H (Tier 3) R1600H (VR)^ R1700G (Tier3) R1700G (VR)^ * * * * * * R2900G (Tier 3) * * * * * * R2900G (VR)^ R3000H (Tier 3) * * * * * * R3000H (VR)^ AD30 (Tier 3) AD30 (VR)^ AD45B (Tier 3) AD55 (Tier 3) * * * * * * AD60 * * * * * * *Information not available at time of printing. ^Ventilation Reduction engine option. Assumes ambient air temperature of 25 C (77 F). 30 Edition

13 GRADE COMPARISON CHART DEGREES PERCENT SLOPE DEGREES SLOPE PERCENT GRADE IN DEGREES AND PERCENTS DEGREES PERCENT Edition 44

14 CONVERSION FACTORS Multiply Metric Unit By To Obtain English Unit kilometer (km) mile meter (m) yard meter (m) 3.28 foot centimeter (cm) foot millimeter (mm) inch sq kilometer (km 2 ) square mile hectare (ha) acre sq meter (m 2 ) square foot sq meter (m 2 ) 1550 square inch sq centimeter (cm 2 ) square inch cu centimeter (cm 3 ) cubic inch cu meter (m 3 ) cubic yard liter (L) cubic inch liter (L) cubic yard km/h mph liter (L) U.S. gallon liter (L) 0.22 Imperial gallon metric ton (t) long ton metric ton (t) short ton kilogram (kg) pound, avdp. gram (g or gr).0353 ounce, avdp. kilonewton (kn) 225 pound (force) newton (N) pound (force) cu centimeter (cm 3 ) fluid ounce kilograms/cu meter pounds/cu yd kilograms/cu meter pounds/cu ft kilograms/sq cm (kg/cm 2 ) pounds/sq in kilocalorie (kcal) Btu kilogram-meter (kg m) foot-pound meter-kilogram (m kg) pound-foot metric horsepower (CV) hp kilowatt (kw) hp kilopascal (kpa) psi bar 14.5 psi tons/m pounds/cu yd decaliter bushel Multiply English Unit By To Obtain Metric Unit mile, statute (m) kilometer yard (yd) meter foot (ft) meter inch (in) 25.4 millimeter sq mile (mile 2 ) sq kilometer acre hectare sq foot (ft 2 ) sq meter sq inch (in 2 ) sq meter cu yard (yd 3 ) cu meter cu inch (in 3 ) cu centimeter cu foot (ft 3 ) cu meter cu inch (in 3 ) liter cubic yard (yd 3 ) liter mph 1.61 km/h Ton mph tkm/h U.S. gallon (US Gal) liter U.S. gallon Imperial gallon long ton (lg ton) metric ton short ton (sh ton) metric ton pound (lb) kilogram ounce (oz) gram pound (lb) (force) kilonewton pound (lb) (force) 4.45 newton fluid oz (fl oz) cu centimeter lb/cu ft (lb/ft 3 ) kg/cu meter lb/cu yd (lb/yd 3 ) kg/cu meter pounds/sq. in kilogram/sq cm psi bar psi 6.89 kilopascal Btu kilogram-calorie foot-pound (ft-lb) kilogram-meter horsepower (hp) metric horsepower horsepower (hp) kilowatt pounds/cu yd tons/m 3 pounds (No. 2 diesel fuel) U.S. gallon bushel decaliter NOTE: Some of the above factors have been rounded for convenience. For exact conversion factors please consult International System of Units (SI) table. 30 Temperature conversion Degree C Degree F C = ( F 32) 1.8 F = (C 1.8) + 32 Edition

15 METRIC UNIT EQUIVALENTS 1 km = 1000 m 1 m = 100 cm 1 cm = 10 mm 1 km 2 = 100 ha 1 ha = 10,000 m 2 1 m 2 = 10,000 cm 2 1 cm 2 = 100 mm 2 1 m 3 = 1000 liters 1 liter = 1000 cm 3 1 metric ton = 1000 kg 1 quintal = 100 kg 1 N = kg m/s 2 1 kg = 1000 g 1 g = 1000 mg 1 bar = psi 1 cal = 427 kg m = cv h = kw h torque unit 1 CV = 75 kg m/s 1 kg/cm 2 = 0.97 atmosph. ENGLISH UNIT EQUIVALENTS 1 mile = 1760 yd 1 yd = 3 ft 1 ft = 12 in 1 sq mile = 640 acres 1 acre = 43,560 sq ft 1 sq ft = 144 sq in 1 cu ft = 7.48 gal liq 1 gal = 231 cu in = 4 quarts liq 1 quart = 32 fl oz 1 fl oz = 1.80 cu in 1 sh ton = 2000 lb 1 lg ton = 2240 lb 1 lb = 16 oz, avdp 1 Btu = 778 ft lb = hph = kwh 1 mechanical hp = 550 ft-lb/sec 1 atmosph. = 14.7 lb/in 2 POWER UNIT EQUIVALENTS kw = Kilowatt hp = Mechanical Horsepower CV = Cheval Vapeur (Steam Horsepower) French Designation For Metric Horsepower PS = Pferdestärke (Horsepower) German Designation For Metric Horsepower 1 hp = CV = PS = kw 1 PS = 1 CV = hp = kw 1 kw = hp = 1.36 CV = 1.36 PS Edition 44

16 Machine Machine Machine Track-Type Tractors Excavators Forest Machines D3K XL/LGP C4.4 ACERT 300.9D Yanmar 3TNV70 320D 6.4 ACERT D4K XL/LGP C4.4 ACERT 301.4C Yanmar 3TNV76 General Forestry (HW) D5K XL/LGP C4.4 ACERT 301.7D Yanmar 3TNV76 General Forestry (HD/LC) D5N XL/LGP 3126B T 301.7D CR Yanmar 3TNV76 Log Loader (U/U) D6K XL/LGP C6.6 ACERT 302.2D Yanmar 3TNV76 324D C7 ACERT D6N XL/LGP C6.6 ACERT 302.4D Yanmar 3TNV76 General Forestry D6G 3306 T 302.7D Yanmar 3TNV76 Log Loader (O/U) D6G Series 2 XL 3306 T 303E (Japan) C1.3 Log Loader (U/U) D6G Series 2 LGP 3306 T 303.5E C D C7 ACERT D6R C9 ACERT 304E C2.4 General Forestry D6T C9 ACERT 305E C2.4 Log Loader (O/U) D6T Tier 4 Interim C9.3 ACERT 305.5E C2.4 Log Loader (U/U) D7E C9.3 ACERT 306E (LRC) C D C9 ACERT D7G 3306 DITA 307E (LRC) C2.6 General Forestry D7G Series DITA 308E C3.3B Log Loader (O/U) D7R Series 2 (All) 3176C SCAC 308E2 C3.3B Log Loader (U/U) D8R/D8R LGP 3406C TA 311D LRR C4.2 ACERT 568 FM C9.3 ACERT D8T/D8T LGP C15 ACERT 312D/312D L C4.2 ACERT General Forestry D9R 3408C TA 313C SR/CR 3064 T Log Loader (O/U) D9T C18 ACERT 314D CR/LCR C4.2 ACERT Log Loader (U/U) D10T C27 ACERT 315D L C4.2 ACERT D11T C32 ACERT 319D L/319D LN C4.2 ACERT Track Harvesters M313D C4.4 ACERT 501HD C6.6 ACERT Motor Graders M315D C4.4 ACERT 120H STD 3116 TA M316D C6.6 ACERT Wheel Harvester 120M C6.6 ACERT M318D C6.6 ACERT 550 C7 ACERT 135H STD 3116 TA M322D C6.6 ACERT 12H STD D/320D L/320D C6.4 ACERT Wheel Skidders 12M C6.6 ACERT RR/320D LRR 525C C7 ACERT 140H STD 3306 T 321D LCR C6.4 ACERT 535C C7 ACERT 140M C7 ACERT 323D/323D L C6.4 ACERT 545C C7 ACERT 160H STD 3306 T 324D L Cat C7 ACERT 160M C9 ACERT 328D LCR Cat C7 ACERT Track Skidders 14M C11 ACERT 329D L C7 ACERT TA 16M C13 ACERT 336D L C9 ACERT TA 24M C18 ACERT 345B L Series II 3176C ATAAC 345D L C13 ACERT Forwarders Skid Steer/Multi-Terrain/ 365C L C15 ACERT 564 C6.6 ACERT Compact Track Loaders 385C/385C L C18 ACERT 574 C6.6 ACERT 216B2 C B 3412B HEUI 584 C7 ACERT 226B2 C2.2T 5130B 3508B (EUI) TA 584HD C7 ACERT 236D C3.3B 5230B 3516B (EUI) TA 242D C3.3B Pipelayers 246D C3.3B Front Shovels PL61 C6.6 ACERT 257D C3.3B 385C FS C18 ACERT 572R2 3176C T 259D C3.3B 5130B 3508 (EUI) TA PL83 C15 ACERT 262D C3.3B 5230B 3516B (EUI) TA PL87 C15 ACERT 272D C D XHP C3.8 Backhoe Loaders Wheel Tractor-Scrapers 277D C3.3B 416E 3054C 621H, 623H, 627H Tractor C13 ACERT 279D C3.3B 416F 3054C, C H Scraper C9 ACERT 287D C3.3B 420F 3054C, C G C18 ACERT 289D C3.3B 430F 3054C, C G Tractor C18 ACERT 299D C F 3054C, C G Scraper C9 ACERT 299D XHP C F 3054C 657G Tractor C18 ACERT 428F 3054C, C G Scraper C15 ACERT 432F 3054C, C F 3054C, C F 3054C, C4.4 *Not sold in U.S., Canada or Europe. 30 Edition

17 Machine Machine Machine Track Feller Bunchers* Wheel Dozers Track Loaders 511 C9 ACERT 814F 3176C ATAAC 939C 3046 T 521 C9 ACERT 814F II C9 ACERT 953D C6.6 ACERT 521B C9 ACERT 824G Series II 3406E ATAAC 963D C6.6 ACERT 522 C9 ACERT 824H C15 ACERT 973C C9 ATAAC 522B C9 ACERT 834G 3456 TA 532 C9 ACERT 834H C18 ACERT Telehandlers 541 C9 ACERT E ATAAC TH255 C4.4 DIT 541 Series 2 C9 ACERT 844H C27 ACERT TH336 C4.4 DITAAC 551 C9 ACERT 854G 3508B TA TH337 C4.4 DITAAC 552 C9 ACERT 854K C32 ACERT TH406 C4.4 DITAAC 552 Series 2 C9 ACERT TH407 C4.4 DITAAC Soil Compactors TH414 C4.4 DITAAC Knuckleboom Loaders 815F 3176C ATAAC TH417 C4.4 DITAAC 519 C6.6 Tier 3 815F II C9 ACERT TH514 C4.4 DITAAC 529 C6.6 Tier 3 825G Series II 3406E ATAAC TL642 C4.4 EDIT 559C C6.6 Tier 4 Interim 825H C15 ACERT TL943 C4.4 EDIT 569 C6.6 Tier 3 TL1055 C4.4 EDITAAC 579C C6.6 Tier 4 Interim Landfill Compactors TL1255 C4.4 EDITAAC 816F 3176 TA Wheel Feller Buncher 816F II C9 ACERT Wheel Material Handlers 553 C6.6 ACERT 826G Series II 3406E TA M318D MH C6.6 ACERT 563 C7 ACERT 826H C15 ACERT M322D MH C6.6 ACERT 573 C7 ACERT 836G 3456 TA M325D MH C7 ACERT 836H C18 ACERT M325D LMH C7 ACERT Mining & Off-Highway Trucks MH3037 Tier 3/ C7.2 ACERT 770G Tier 4 Final C15 ACERT Wheel Loaders/Integrated Toolcarriers Stage IIIA 770G C15 ACERT 901C (Japan) C1.8 MH3037 Tier 4 Final/ C7.1 ACERT 772G Tier 4 Final C18 ACERT 902C (Japan) C2.4 Stage IV 772G C18 ACERT 903C (Japan) C2.4 MH3049 C9 ACERT 773G Tier 4 C27 ACERT 906H C3.4 MH3059 C9 ACERT 773G C27 ACERT 906H2 C3.3B 775G Tier 4 C27 ACERT 907H C3.4 Track Material Handlers 775G C27 ACERT 907H2 C3.3B 385C MH C18 ACERT 777D 3508B (EUI) TA 908H C G Tier 4 C32 ACERT 908H2 C3.3B Paving Products 777G C32 ACERT 914G/IT14G 3054 T Cold Planers 785C 3512B (EUI) TA 924K C6.6 ACERT PM102 C7 ACERT 785D 3512C HD (EUI) ATAAC 930K C6.6 ACERT PM200 C18 ACERT 789C 3516B (EUI) TA 938K C6.6 ACERT PM201 C18 ACERT 793D 3516B (EUI) TA 950K C7.1 ACERT 793F C (EUI) ATAAC 962K C7.1 ACERT Reclaimer/Soil Stabilizers 797F C (EUI) ATAAC 966K C9.3 ACERT RM300 C11 ACERT 972K C9.3 ACERT RM500 C15 ACERT Articulated Trucks 980K C13 ACERT 725 C11 ATAAC 950H C7 ATAAC Asphalt Pavers 730 C11 ATAAC 962H C7 ATAAC AP600 C6.6 ACERT 730 Ejector C11 ATAAC 966H C11 ATAAC AP600 (EAME) 3056E ATAAC 735 C15 ATAAC 966M C9.3 ACERT AP800D 3054 DIT 740 C15 ATAAC 972H C13 ATAAC AP1000D C7 ACERT 740 Ejector C15 ATAAC 972M C9.3 ACERT AP655D C6.6 ACERT 980H C15 ATAAC AP655D (EAME) C6.6 ACERT 988K C18 ACERT AP755 (EAME) C7 ACERT 990H C27 ACERT AP1055D C7 ACERT 992K C32 ACERT BG-230D 3054C ATAAC 993K C32 ACERT BG-260D C7 ACERT 994D 3516B TA BG-225C 3054C 994F Cat 3516B HD EUI *s 511 through 552 are also available as a Track Harvester. NOTE: The 950K, 962K, 966K, 972K and 980K are Tier 4 Interim/Stage IIIB machines and only available in North America and Europe. Contact your local Cat dealer for product availability. NOTE: The 950H, 962H, 966H, 972H and 980H are not available in all regions. Contact your local Cat dealer for product availability Edition 44

18 Machine Machine Machine Compactors Double Drum and Combi Pneumatic Tire-Asphalt Single Drum, Smooth CB14 C1.1 PS150C 3054C CS-323C 3054C CB14 XW C1.1 PS360C 3054C ATAAC CS-423E 3054C CB14 Full Flush C1.1 PF300C 3054C CS-433E 3054C T CB22 C1.5 PS300C 3054C CS54 C4.4 ACERT CB24 C1.5 CS56 C6.6 ACERT CB32 C1.5 Underground Mining CS64 C6.6 ACERT CC24 C1.5 R1300G 3306B DITA CS74 C6.6 ACERT CB34 C2.2 R1600H C11 ACERT ATAAC CS76 C6.6 ACERT CB34 XW C2.2 R1700G C11 ACERT ATAAC CS76 XT C6.6 ACERT CC34 C2.2 R2900G C15 ACERT ATAAC CB-434D 3054C R3000H C15 ACERT ATAAC Single Drum, Padded CB434D XW 3054C AD30 C15 ACERT ATAAC CP-323C 3054C CB-534D/CB-534D XW 3054C AD45B C18 ACERT ATAAC CP-433E 3054C T CB564D 3054C AD55 C18 ACERT ATAAC CP54 C4.4 ACERT AD60 C27 ACERT CP56 C6.6 ACERT CP64 C6.6 ACERT CP74 C6.6 ACERT CP76 C6.6 ACERT 30 Edition

19 and (Cylinders) Machine Aspiration Mitsubishi L3E (3) Mitsubishi S3L2 (3) Mitsubishi S3Q2 (3) Mitsubishi S4Q2 (4) Fuel Injection System Bore Stroke Displacement mm in L in C, 301.8C NA DI C NA DI C CR NA DI C CR T 304C CR NA DI C CR T 3013C (3) CB-214E, CB-224E, CB-225E NA DI Mitsubishi 307C, 307C SB, 308C CR NA DI M40EI (4) C E (Japan) NA DI C E, 901C (inside Japan only) NA DI C2.2 CB-334E, CB-335E, 902, 216B3 NA DI B3, 247B3 T C E, 305E, 305.5E, 902C (Japan), NA DI C (Japan) C E (China), 307E (China) T DI C3.3B 308E, 906H2, 907H2, 908H2, 236D, T DI D, 246D, 257D, 259D, 262D, 277D, 279D, 287D, 289D C D, 272D XHP, 299D, 299D XHP T DI Yanmar 3TNV D NA IDI Yanmar 3TNV C, 301.7D, 301.7D CR, 302D, NA IDI D, 302.7D 3046 D3G XL, D3G LGP, D4G XL, NA DI CS-533E, D4G LGP, D5G XL, D5G LGP, CP-533E, 315C/315C L*, 939C T DI 3054C (I-4) 416E, 416F, 420F, 430F, 450F, 422F, 428F, 432F, 434F, 444F NA/T*** DI E (I-4) CB-434D, CS-323C, CS-423E, CP-323C, PS-150C AP-800C, BG-230, BG-650, 908, 914G, IT14G, PS-360B, PF-300B, PS-300B, CS-433E, CP-433E, CB-534C M313C, M315C, AP-650B, 315C L**, BG-225C NA DI T (optional) TA ***Japan sourced. ***France sourced. ***Turbo optional on some models. DI Direct Injection TA Turbocharged and Aftercooled T Turbocharged NA Naturally Aspirated NOTE: Materials and specifications subject to change without notice. Component commonality of Cat s for all applications does not imply complete interchangeability. Contact your Cat dealer for specific information Edition 44

20 and (Cylinders) Machine Aspiration (I-4) (I-4) CS-563E, CS-573E, CS-583E, CS-663E, AP-655C, CS-683E, CP-563E, CP-573E, CP-583E, CP-663E, M316C, M318C, M322C 311C U, 312C, 314C CR/LCR, 313C SR/CR 320C, 320C L, 320C LN, 320C S, 321C LCR Fuel Injection System Bore Stroke Displacement mm in L in 3 ATAAC DI T DI T DI CB-634D, BG-240C, AP-900B T DI BG-260C, BG-245C, AP-1050B, AP-1055B, 120H STD, 135H STD, BG-2455C, AP-1000B TA DI D5**, D6N**, 561N, 953C, 963C T DI B, 535B TA 325C LN ATAAC 527, 517 TA DI C4.2 ACERT 311D, 311D LRR, 312D, 312D L, ATAAC DI D CR, 314D LCR, 315D L, 319D C4.4 ACERT D3K, D4K, D5K, 416F, 420F, 430F, T DI F, 428F, 432F, 434F, 444F C6.4 ACERT 320D, 320D L, 320D RR, 320D LRR, ATAAC DI D LCR, 323D L C6.6 R1300G II ATAAC DI C6.6 ACERT D6K, D6N, 953D, 963D, 120M, 12M, PL61, 924K, 930K, 938K, M318D MH, M322D MH TA DI C7 ACERT 324D L, 328D LCR, 329D L, 950H, 962H, IT62H, M325D MH, M325D LMH ATAAC DI C7.1 ACERT 950K, 962K, MH3037 Tier 4 Final/ ATAAC DI Stage IV C7.2 ACERT MH3037 Tier 3/Stage IIIA ATAAC DI C9 ACERT C9 ACERT D L, 814F II, 815F II, D6T, MH3049, MH M, 336D, 336D L, 336D LN, 627G Sc., 637G Sc., 973C 572R2, 345B L Series II, D7R Series 2 (All), 814F, 815F, 816F ATAAC DI TA DI ATAAC DI C9.3 ACERT D6T Tier 4 Interim, D7E, 568 and ATAAC DI other models, 966K, 966M, 966K XE, 972K, 972M **France sourced. **Not sold in U.S., Canada or Europe. DI Direct Injection TA Turbocharged and Aftercooled T Turbocharged ATAAC Air/Air Aftercooled NOTE: Materials and specifications subject to change without notice. Component commonality of Cat s for all applications does not imply complete interchangeability. Contact your Cat dealer for specific information. 30 Edition

21 and (Cylinders) Machine Aspiration C11 C11 ACERT C13 ACERT C15 ACERT (V-8) R1300G, 12H STD, D6G, 140H STD, 160H STD Fuel Injection System Bore Stroke Displacement mm in L in 3 T DI D7G TA DI 545 ATAAC DI 365B L Series II ATAAC DI RM-250C, RM-350B, D8R, D8R LGP TA DI G Series II, 825G Series II, 824G Series II, AD30 ATAAC DI 725, 730, 730 Ejector ATAAC DI R1600H, R1700G, 14M, 966H TA DI ATAAC 16M, 345D L, 972H, 621H, TA DI H, 627H Tr, 980K D8T, D8T LGP, PL83, PL87, TA DI G Sc., 770G Tier 4 Final, 770G R2900G, R3000H, AD30, 735, 740, ATAAC DI Ejector, 824H, 825H, 826H, 980H 834G, 836G, 385B, 385B L, 5090B ATAAC DI D9R, 589, PM-565B TA DI ATAAC TA DI C18 ACERT AD45B, AD55, D9T, 631G, 637G Tr., 657G Tr., 988K, 772G Tier 4 Final, 772G, 834H, 836H, 385C MH C27 ACERT (V-12) 3412 (V-12) 3508 (V-8) 3512 (V-12) 3512 HD (V-12) 3516 (V-16) 3516 HD (V-16) AD60, D10T, 773G Tier 4 Final, 773G, 775G Tier 4 Final, 775G, 990H, 844H TA DI D10R, 5110B TA DI , 773E ATAAC DI D11R, 5130B, 992K, 854G, 777D TA DI C TA DI D ATAAC DI C, 994D, 5230B, 994F TA DI D ATAAC DI D TA DI TA DI C32 ACERT 777G Tier 4 Final, 777G, 854K, 992K, 993K, D11T, D11T CD C F, 795F ATAAC DI (V-16) C (V-20) 797F ATAAC DI DI Direct Injection TA Turbocharged and Aftercooled T Turbocharged ATAAC Air/Air Aftercooled NOTE: Materials and specifications subject to change without notice. Component commonality of Cat s for all applications does not imply complete interchangeability. Contact your Cat dealer for specific information Edition 44