GKC1825L

Transcription

1 GKC1825L

2 A B C D E 2

3 F G H I J K 3

4 L M N O P Q 4

5 R S T U V 5

6 ENGLISH (Original instrctions) Intended se Yor BLACK+DECKER TM chainsaw has been designed for prning and felling trees and ctting logs. This tool is intended for consmer se only. Safety instrctions General power tool safety Warning! Read all safety warnings and all instrctions. Failre to follow the warnings and instrctions listed below may reslt in electric shock, fire and/or serios injry. Save all warnings and instrctions for ftre reference. The term "power tool" in all of the warnings listed below refers to yor mains operated (corded) power tool or battery operated (cordless) power tool. 1. Work area safety a. Keep work area clean and well lit. Clttered or dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, sch as in the presence of flammable liqids, gases or dst. Power tools create sparks which may ignite the dst or fmes. c. Keep children and bystanders away while operating a power tool. Distractions can case yo to lose control. 2. Electrical safety a. Power tool plgs mst match the otlet. Never modify the plg in any way. Do not se any adapter plgs with earthed (gronded) power tools. Unmodified plgs and matching otlets will redce risk of electric shock. b. Avoid body contact with earthed or gronded srfaces sch as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if yor body is earthed or gronded. c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d. Do not abse the cord. Never se the cord for carrying, plling or nplgging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e. When operating a power tool otdoors, se an extension cord sitable for otdoor se. Use of a cord sitable for otdoor se redces the risk of electric shock. f. If operating a power tool in a damp location is navoidable, se a residal crrent device (RCD) protected spply. Use of an RCD redces the risk of electric shock. 3. Personal safety a. Stay alert, watch what yo are doing and se common sense when operating a power tool. Do not se a power tool while yo are tired or nder the inflence of drgs, alcohol or medication. A moment of inattention while operating power tools may reslt in serios personal injry. b. Use personal protective eqipment. Always wear eye protection. Protective eqipment sch as dst mask, non-skid safety shoes, hard hat, or hearing protection sed for appropriate conditions will redce personal injries. c. Prevent nintentional starting. Ensre the switch is in the off-position before connecting to power sorce and/or battery pack, picking p or carrying the tool. Carrying power tools with yor finger on the switch or energising power tools that have the switch on invites accidents. d. Remove any adjsting key or wrench before trning the power tool on. A wrench or a key left attached to a rotating part of the power tool may reslt in personal injry. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in nexpected sitations. f. Dress properly. Do not wear loose clothing or jewellery. Keep yor hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caght in moving parts. g. If devices are provided for the connection of dst extraction and collection facilities, ensre these are connected and properly sed. Use of dst collection can redce dst-related hazards. 4. Power tool se and care a. Do not force the power tool. Use the correct power tool for yor application. The correct power tool will do the job better and safer at the rate for which it was designed. b. Do not se the power tool if the switch does not trn it on and off. Any power tool that cannot be controlled with the switch is dangeros and mst be repaired. c. Disconnect the plg from the power sorce and/or the battery pack from the power tool before making any adjstments, changing accessories, or storing power tools. Sch preventive safety measres redce the risk of starting the power tool accidentally. 6

7 (Original instrctions) ENGLISH d. Store idle power tools ot of the reach of children and do not allow persons nfamiliar with the power tool or these instrctions to operate the power tool. Power tools are dangeros in the hands of ntrained sers. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before se. Many accidents are cased by poorly maintained power tools. f. Keep ctting tools sharp and clean. Properly maintained ctting tools with sharp ctting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instrctions, taking into accont the working conditions and the work to be performed. Use of the power tool for operations different from those intended cold reslt in a hazardos sitation. 5. Battery tool se and care a. manfactrer. A charger that is sitable for one type of another battery pack. b. designated battery packs. Use of any other battery packs may create c. When battery pack is not in se, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may case brns d. Under absive conditions, liqid may be ejected from the battery; avoid contact. If contact accidentally additionally seek medical help. Liqid ejected from the battery may case irritation or brns. 6. Service a. person sing only identical replacement parts. This will ensre that the safety of the power tool is maintained. b. Power to the tool shold always be spplied via residal crrent device with a rated residal crrent of 30mA or less. Additional power tool safety Warning! Additional safety warnings for chainsaws Keep all parts of the body away from the saw chain when the chainsaw is operating. Before yo start the chainsaw, make sre the saw chain is not contacting anything. A moment of inattention while operating chain saws may case entanglement of yor clothing or body with the chain saw. Always hold the chainsaw with yor right hand on the rear handle and yor left hand on the front handle. increases the risk of personal injry and shold never be done. Hold the power tool by inslated gripping srfaces only, becase the saw chain may contact hidden wiring. Saw chains contacting a "live" wire may make exposed metal parts of the power tool "live" and cold give the operator an electric shock. Wear safety glasses and hearing protection. Frther protective eqipment for head, hands, legs and feet is recommended. Adeqate protective clothing will redce the saw chain. Do not operate a chainsaw in a tree. Operation of a chainsaw while p in a tree may reslt in personal injry. Always keep proper footing and operate the chain saw Slippery or nstable srfaces sch as ladders may case a loss of balance or control of the chainsaw. When ctting a limb that is nder tension be alert for spring back. released the spring loaded limb may strike the operator and/or throw the chain saw ot of control. Use extreme cation when ctting brsh and saplings. The slender material may catch the saw chain and be whipped toward yo or pll yo off balance. Carry the chain saw by the front handle with the chain saw switched off and away from yor body. When gide bar cover. Proper handling of the chain saw will redce the likelihood of accidental contact with the moving saw chain. Follow instrctions for lbricating, chain tensioning and changing accessories. Improperly tensioned or lbricated chain may either break or increase the chance for kickback Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery casing loss of control. 7

8 ENGLISH (Original instrctions) Ct wood only. Do not se chainsaw for prposes not intended. For example: do not se the chainsaw for ctting plastic, masonry or non-wood bilding materials. Use of the chainsaw for operations different than intended cold reslt in a hazardos sitation. Cases and operator prevention of kickback Kickback may occr when the nose or tip of the gide bar toches an object, or when the wood closes in and pinches the saw chain in the ct. Tip contact in some cases may case a sdden reverse reaction, kicking the gide bar p and back towards the operator. Pinching the saw chain along the top of the gide bar may psh the gide bar rapidly back towards the operator. Either of these reactions may case yo to lose control of the chainsaw which cold reslt in serios personal injry. Do not rely exclsively pon the safety devices bilt into yor chainsaw. As a chainsaw ser, yo shold take several steps to keep yor ctting jobs free from accident or injry. Kickback is the reslt of tool misse and / or incorrect operating procedres or conditions and can be avoided by taking proper precations as given below: Maintain a firm grip, with thmbs and fingers encircling the chainsaw handles. With both hands on the chainsaw, position yor body and arm to allow yo to resist kickback forces. Kickback forces can be controlled by the operator, if proper precations are taken. Do not let go of the chainsaw. Do not overreach and do not ct above sholder height. This helps prevent nintended tip contact and enables better control of the chainsaw in nexpected sitations. Only se replacement gide bars and chains specified by the manfactrer. Incorrect replacement gide bars and chains may case chain breakage and/ or kickback. Follow the manfactrer's sharpening and maintenance instrctions for the saw chain. Decreasing the depth gage height can lead to increased kickback. Striking metal, cement or any other hard material near the wood, or bried in the wood can case kickback. A dll or loose chain can case kickback. Do not try to insert into a previos ct. As this cold case kickback. Make a fresh ct every time. Safety recommendations for the chainsaw We strongly recommend that first time sers obtain practical instrction in the se of the chainsaw and protective eqipment from an experienced ser. Initial practice shold be completed sawing logs on a saw horse or cradle. We recommend that when carrying the chainsaw that yo remove the battery and make sre that the saw chain is facing backwards. 8 Maintain yor chainsaw when not in se. Do not store yor chainsaw for any length of time withot first removing the saw chain and gide bar which shold be kept immersed in oil. Store all parts of yor chainsaw in a dry, secre place ot of reach of children. We recommend yo drain the oil reservoir prior to storage. Be sre of yor footing and pre-plan a safe exit from a falling tree or branches. Use wedges to help control felling and prevent binding the gide bar and saw chain in the ct. Saw chain care. Keep the saw chain sharp and sng on the gide bar. Ensre the saw chain and gide bar are clean and well oiled. Keep handles dry, clean and free from oil and grease. Avoid ctting Prepared timber. Into the grond. Into wire fences, nails. etc. Additional safety instrctions Ensre someone is nearby (bt at a safe distance) in case of an accident. If for any reason yo have to toch the saw chain, make sre yor chainsaw is disconnected from the mains. The noise from this prodct can exceed 85 db(a). We therefore recommend yo take appropriate measres for the protection of hearing. When handling the prodct the chain bar may become hot, handle with care. Safety of others This appliance is not intended for se by persons (inclding children) with redced physical, sensory or mental capabilities, or lack of experience and knowledge, nless they have been given spervision or instrction concerning se of the appliance by a person responsible for their safety. Children shold be spervised to ensre that they do not play with the appliance. Residal risks. Additional residal risks may arise when sing the tool which may not be inclded in the enclosed safety warnings. These risks can arise from misse, prolonged se etc. Even with the application of the relevant safety reglations and the implementation of safety devices, certain residal risks can not be avoided. These inclde: Injries cased by toching any rotating/moving parts. Injries cased when changing any parts, blades or accessories.

9 (Original instrctions) ENGLISH Injries cased by prolonged se of a tool. When sing any tool for prolonged periods ensre yo take reglar breaks. Impairment of hearing. Health hazards cased by breathing dst developed when sing yor tool (example:- working with wood, especially oak, beech and MDF.) Vibration The declared vibration emission vales stated in the technical data and the declaration of conformity have been measred in accordance with a standard test method provided by EN and may be sed for comparing one tool with another. The declared vibration emission vale may also be sed in a preliminary assessment of exposre. Warning! The vibration emission vale dring actal se of the power tool can differ from the declared vale depending on the ways in which the tool is sed. The vibration level may increase above the level stated. When assessing vibration exposre to determine safety measres reqired by 2002/44/EC to protect persons reglarly sing power tools in employment, an estimation of vibration exposre shold consider, the actal conditions of se and the way the tool is sed, inclding taking accont of all parts of the operating cycle sch as the times when the tool is switched off and when it is rnning idle in addition to the trigger time. Labels on tool The following pictograms are shown on the tool: Switch the tool off. Before performing any maintenance on the tool, remove the battery from the tool. 92 Directive 2000/14/EC garanteed sond powe r. Chain oil. Moving direction of the chain (Marked nder teh sprocket cover).. Hold and operate the saw properly with both hands. Do not operate the saw sing only one hand. Contact of teh gide bar tip with any object shold be avoided! Tip contact may case the gide bar to move sddenly pward and backward, which may case serios injry. Warning! Do not toch chain at the chip ejection point. Cation: Do not over tighten. Tighten by hand. Finger tight only. : R Warning! Read the manal prior to operation. Warning! To redce the risk of injry, the ser mst read the instrction manal. Wear eye, ear and head protectionwhen sing this prodct. Wear non-silp safety footwear when sing the prodct. Wear non-silp, heavy dtygloves when sing this prodct. Do not expose the tool to rain or high hmidit y. Additional safety instrctions for batteries and chargers Batteries Never attempt to open for any reason. Do not expose the battery to water. Do not store in locations where the temperatre may exceed 40 C. Charge only at ambient temperatres between 10 C and 40 C. Charge only sing the charger provided with the tool. When disposing of batteries, follow the instrctions given in the section "Protecting the environment". p Do not attempt to charge damaged batteries. Keep bystanders away. 9

10 ENGLISH (Original instrctions) Chargers Use yor BLACK+DECKER charger only to charge the battery in the tool with which it was spplied. Other batteries cold brst, casing personal injry and damage. Never attempt to charge non-rechargeable batteries. Have defective cords replaced immediately. Do not expose the charger to water. Do not open the charger. Do not probe the charger. $ + Electrical safety Featres 1. On/off switch 2. Lock-off btton 3. Oil cap 4. Front gard 5. Chain tension adjstment ring 6. Chain 7. Gide bar 8. Chain sheath 9. Chain adjst locking knob 10. Chain cover assembly 11. Oil level indicator 12. @ The charger is intended for indoor se only. Read the instrction manal before se. # Yor charger is doble inslated; therefore no earth wire is reqired. Always check that the mains voltage corresponds to the voltage on the rating plate. Never attempt to replace the charger nit with a reglar mains plg. If the spply cord is damaged, it mst be replaced by the manfactrer or an athorised Black & Decker Service Centre in order to avoid a hazard. Warning! Always wear protective gloves when working on yor chainsaw. Warning! Before performing any assembly or maintenance on power tools, switch off and remove the battery. Warning! Remove the cable tie that attaches the chain to the chainbar before assembly. Trn the tension adjst ring (5) anti-clockwise as far as it will go so the arrow on the tension adjst ring (5) lines p Place the chain (6) over the gide bar (7) making sre that the saw chain ctters on the pper part of the gide bar Gide the chain (6) arond the gide bar (7) and pll it to create a loop to one side at the rear end of the gide bar (7). Gide the chain (6) arond the drive sprocket (14). Place G). Place the chain cover assembly (10) onto the chainsaw Trn the chain adjst locking knob (9) clockwise to attach Trn the chain adjst locking knob (9) 180 degrees anti Trn the chain tension adjst ring (5) clockwise ntil the chain (6) is tight. Make sre that the chain (6) is sng Check the tension as described below. Do not overtighten. Tighten the chain adjst locking knob (9) (L). Before se and after every 10 mintes of se, yo mst check the chain tension. Remove the battery (12). The tension is correct when the chain (6) snaps back after being plled 3 mm away from the gide bar (7). There shold be no "sag" between the gide bar (7) and the chain (6) on the nderside. Note: Do not over-tension the chain as this will lead to excessive wear and will redce the life of the gide bar and the chain. Note: When the chain is new, check the tension freqently se becase a new chain stretches slightly. Trn the chain adjst locking knob (9) 180 degrees anti Tension the chain sing the chain tension adjsting ring T A). 10

11 (Original instrctions) ENGLISH tool. Slide the battery into the receptacle and psh ntil the battery snaps into place. To remove the battery, psh the release bttons (16) while at the same time plling the battery ot of the receptacle. Use Warning! Let the tool work at its own pace. Do not overload. battery is defective and shold be retrned to a service centre for recycling. If the new battery gives the same indication as the original battery, take the charger to be tested at an athorised services centre. Note: It may take as long as 30 mintes to determine that the battery is defective. If the battery is too hot or too cold, the charging indicator will alternately blink red, fast done before. The battery may become warm while charging; this is normal and does not indicate a problem. Warning! Do not charge the battery at ambient temperatres below 10 C or above 40 C. Recommended charging temperatre: approx. 24 C. Note: The charger will not charge a battery if the cell temperatre is below approximately 10 C or above 40 C. The battery shold be left in the charger and the charger will begin to charge atomatically when the cell temperatre warms p or cools down. To charge the battery (12), insert it into the charger (19). not force. Be sre that the battery is flly seated in the charger. Plg in the charger and switch on at the mains. The charging indicator (18) will blink. The charge is complete when the charging indicator (18) switches to continosly on. The charger and the battery switch on as the charger occasionally tops p the battery charge. Charge discharged batteries within 1 week. Battery life will be greatly diminished if stored in a discharged state. Leaving the battery in the charger The charger and battery pack can be left connected with the the battery pack fresh and flly charged. Charger diagnostics If the charger detects a weak or damaged battery, the chargfollows: Re-insert the battery (12). rate, se a different battery to determine if the charging process works properly. If the replaced battery charges correctly, the original - recommended chain oil. Yo can see the oil level in the oil Periodically switch off and check the oil level indicator (11); if it is less than a qarter fll, remove the battery from Oiling the chain We recommend that yo se only Black & Decker oil (A )dring the lifetime of yor chainsaw becase mixtres of different oils cold lead to the oil becoming degraded, which can drastically shorten the lifetime of the saw chain and create additional risks. It is normal for a small amont of excess oil drip from the chain saw bar and chain dring storage. Do not store chain saw on top of any thing that may be damaged by the dripping oil. Never se waste oil, thick oil or very thin sewing machine oil. These may damage yor chainsaw. The saw chain (6) mst be oiled before each se and after cleaning sing only the correct grade of oil (cat. no. A6023- QZ). Lbricate the saw chain (6) by slowly pressing the blb each ct. Hold the blb down for 1 second each time. f btton (2) with yor thmb and then psh the on/off switch (1) to start. When the motor starts, remove yor thmb from the lock- Do not force the tool, allow the tool to do the work. It will do a better and safer job at the speed for which it is designed. Excessive force will stretch the saw chain (6). If the saw chain (6) or gide bar (7) becomes jammed Switch the tool off. Remove the battery (12). Open the ct with wedges to relieve the strain on the gide bar (7). Do not try to wrench the chainsaw free. Start a fresh ct. 11

12 ENGLISH (Original instrctions) Inexperienced sers shold not attempt to fell trees. The ser may sffer injry or case damage to property as a reslt of failre to control the direction of fall, the tree may splinter or damaged/dead branches may fall dring ctting. The safe distance between a tree to be felled and bystanders, bildings and other objects is at least 2 1/2 times the height of the tree. Any bystander, bilding or object within this distance is at risk from being strck by the tree when felled. Before attempting to fell a tree: Make sre that there are no local by-laws or reglations that wold prohibit or control the felling of the tree. Consider all conditions that may affect the direction of fall, inclding: The intended direction of fall. The natral lean of the tree. Any nsal heavy limb strctre or decay. Srronding trees and obstacles inclding overhead lines and ndergrond drains. The wind speed and direction. Pre-plan a safe exit from falling trees or branches. Make sre that the exit rote is clear of obstacles that wold prevent or hinder movement. Remember that wet grass and freshly ct bark is slippery. Do not attempt to fell trees where the tree diameter is greater than the ctting length of the chainsaw. Ct a direction notch to determine the direction of fall. Make a horizontal ct to a depth of between 1/5th and 1/3rd of the diameter of the tree, perpendiclar to the line and make a notch of abot 45. Make a single horizontal felling ct from the other side 25 Q). Do not ct throgh to the direction notch, yo cold lose control of the direction of fall. Drive a wedge or wedges into the felling ct to open it and Prning trees Make sre that there are no local by-laws or reglations that wold prohibit or control the prning of the tree limbs. Prning shold only be ndertaken by experienced sers there is an increased risk of the saw chain pinching and kick back. Before prning consideration shold be given to conditions affecting the direction of fall inclding: The length and weight of the branch to be ct. Any nsal heavy limb strctre or decay. Srronding trees and obstacles inclding overhead. The wind speed and direction. 12 The branch being intertwined with other branches. The operator shold consider access to the tree limb and the direction of fall. The tree branch is liable to swing towards the tree trnk. In addition to the ser bystanders, objects and property below the branch will be at risk. T - tion to a maximm depth of one third the diameter of the branch. How yo shold ct depends on how the log is spported. Use a saw horse whenever possible. Always start a ct with the saw chain rnning and the spiked bmper (20) in contact - tion of the spiked bmper against the wood. When spported along its whole length: Make a downward ct, bt avoid ctting the earth as this will blnt yor saw chain qickly. When spported at both ends: First, ct one third down to avoid splintering and second, When spported at one end: First ct one third p to avoid splintering and second, ct down to prevent splintering. When on a slope: Always stand on the phill side. Secre the workpiece sing chocks or wedges. The ser or a bystander shold not steady the log by sitting or standing on it. Make sre that the saw chain does not contact the grond. This is strongly recommended whenever possible. Position the log in a stable position. Always ct on the otside of the saw horse arms. Use clamps or straps to secre the workpiece. Removing the branches from a fallen tree. When limbing, leave larger lower limbs to spport the log off the grond. Remove the small limbs in one ct. Branches nder tension shold be ct from the bottom of the branch towards the top to avoid binding the chain saw. Trim limbs from opposite side keeping tree stem between yo and saw. Never make cts with saw between yor legs or straddle the limb to be ct.

13 (Original instrctions) ENGLISH Trobleshooting Problem Possible case Possible soltion Tool will not start Lock btton not pressed. Press the lock btton. Fit the battery Battery not charged Charge the battery corectly battery Chain does not stop within 2 seconds when the tool is switched off Bar/chain appear hot/ smoking Chainsaw does not ct well Chainsaw not sing oil Chainsaw stops sddnely dring se Chain tension is too Check chain tension slack Oil tank empty Check oil tank level Oil hole blocked on chain bar E) and clear the groove arond the edge of the chainbar. Chain tension is too Check chain tension tight Gide bar sprocket Oil the gide bar nose needs greasing sprocket nose Chain on backwards Check/modify chain direction Sharpen Debris in tank Empty oil from tank and replace Oil hole in cap blocked Remove debris from hole Debris in chain bar Remove debris and clean the chain bar Debris in oil otlet Remove debris Battery depleted Re-charge battery if reqired. Battery too hot Leave the battery to cool for atleast 30 mintes before proceeding or charging. Voltage limit protection Restart the chainsaw. Let the tool work at its own pace. Do not overload. Maintenance Reglar maintenance ensres a long effective life for the tool. We recommend yo make the following checks on a reglar basis. Warning! Before performing any maintenance on power tools: Switch off and disconnect the tool from the mains spply. Oil level The level in the reservoir shold not be allowed to fall below a qarter fll. Saw chain and gide bar After every few hors of se and before storage, remove the gide bar (7) and the saw chain (6) and clean them thoroghly. Make sre that the gard is clean and free from debris. Oil sprocket nose and chain bar via the sprocket lbricawear arond the gide bar rails. Saw chain sharpening If yo are to get the best possible performance from the tool it is important to keep the teeth of the saw chain sharp. Gidance for this procedre is fond on the sharpener package. Replacing worn ot saw chains Replacement saw chains are available throgh retailers or Black & Decker service agents. Always se genine spare parts. (Replacements chain part nmber A6125CSL-XJ). Saw chain sharpness The saw chain ctters will blnt immediately if they toch the grond or a nail while ctting. Saw chain tension Reglarly check the saw chain tension. What to do if yor chainsaw needs repair. Yor chainsaw is manfactred in accordance with the relevant safety reqirements. Repairs shold only be carried ot may reslt in considerable danger to the ser. We recommend yo keep this ser manal in a safe place. 13

14 ENGLISH (Original instrctions) Protecting the environment Separate collection. This prodct mst not be disposed of with normal hosehold waste. Shold yo find one day that yor Black & Decker prodct needs replacement, or if it is of no frther se to yo, do not dispose of it with hosehold waste. Make this prodct available for separate collection. Separate collection of sed prodcts and packaging allows materials to be recycled and z sed again. Re-se of recycled materials helps prevent environmental polltion and redces the demand for raw materials. Local reglations may provide for separate collection of electrical prodcts from the hosehold, at mnicipal waste sites or by the retailer when yo prchase a new prodct. Black & Decker provides a facility for the collection and recycling of Black & Decker prodcts once they have reached the end of their working life. To take advantage of this service please retrn yor prodct to any athorised repair agent who will collect them on or behalf. Yo can check the location of yor nearest athorised repair agent by contacting yor local Black & Decker office at the address indicated in this manal. Alternatively, a list of athorised Black & Decker repair agents and fll details of or after-sales service and contacts are available on the Internet at: Technical data GKC1825L20 (H1) Voltage V dc 18 Bar length mm 250 Max bar length mm 250 Chain speed (No-load) m/sm 3.5 Max ctting length mm 250 Oil capacity ml 55 Weight kg 3.1 Battery BL2018 Voltage V DC 18 Capacity Ah 2.0 Type Li-Ion Charger ** (typ. 1) Inpt Voltage V AC Otpt Voltage V DC 8-20 Crrent ma 400 Approx. charge time h 5 Level of sond pressre according to EN 60745: L pa (sond pressre) 70.5 db(a), Uncertainty (K) 1.5 db(a) L WA (sond power) 90.5 db(a), Uncertainty (K) 1.5 db(a) Vibration total vales (triax vector sm) according to EN 60745: Vibration emission vale (a h ) 4.49 m/s 2, ncertainty (K) 1.5 m/s 2 14

15

16 Astralia & New Zealand Stanley Black & Decker Tel (Ast) or Tel (NZ) /2015