Sewage ejection units

Transcription

1 Sewage ejection units Kompaktboy Operation manual 1

2 Table of contents: Page Declaration of conformity General Introduction Enquiries and orders Technical data Range of application Accessories Safety Marking of the notes contained in the operation manual Personnel development and training Dangers in case of non-observance of the safety notes Safety-conscious way of working Safety notes for the operator/user Safety notes concerning maintenance, inspection, and assembly works Unauthorised modification of the machine and fabrication of spare parts Unauthorised modes of operation Transport and temporary storage Transport Temporary storage/conservation Description General Composition and mode of operation Installation Preparation Assembly Placement Inlet Pressure pipe Ventilation Electrical connection Commissioning Maintenance/repair Inspection- and maintenance intervals Maintenance works Collecting tank Non-return valve Miscellaneous Malfunctions; causes and elimination Warranty Technical modifications Appendix: A Example of installation B Dimensions C Sectional drawing and spare parts list

3 Declaration of conformity We, the ZEHNDER Pumpen GmbH Zwönitzer Straße Grünhain-Beierfeld, herewith declare that the sewage ejection units of the type series Kompaktboy conform to the following relevant regulations: - EC low voltage directive 2006/95/EC - EMC directive 2004/108/EC - Machinery directive 2006/42/EC Applied conform standards, particularly - EN EN EN EN EN Grünhain, 03/04/2010 Matthias Kotte Product devlopment 3

4 1. General 1.1 Introduction This operating manual is valid for the sewage ejection units of the type series Kompaktboy. If the instructions of the operation manual especially the safety instructions - are not observed, or in case of unauthorized modifications of the unit or the installation of non-original spare parts, the guarantee expires automatically. The manufacturer assumes no liability for damages resulting from such behaviour! Such as any other electrical device, this product may fail due to absence of mains voltage or a technical failure. If damage could occur, an emergency power supply, a hand diaphragm pump, a second unit (duplex unit) and/or an off-grid alarm device should be provided according to the application. We as manufacturer are at your disposal for consultation also after the purchase. In case of failures or damages, please contact your retailer. Manufacturer ZEHNDER Pumpen GmbH Zwönitzer Straße Grünhain-Beierfeld Manufactured sizes: Kompaktboy 1.1 W Kompaktboy 1.1 D Kompaktboy 1.5 D Kompaktboy 3.0 D - 2P State of the operation manual: April Enquiries and orders In case of enquiries or orders, address yourself to your specialist retailer. 1.3 Technical data Type Kompaktboy Output power P 1 (kw) Output power P 2 (kw) Voltage U (V) Power reception I max (A) Rotational speed (n /min) 1.1 W D D D-2P Pressure socket DN 100 Inlet 3 x DN 50 2 x DN 100* 1 x DN x DN 50/100 Inlet heights h (mm) * / 428 Type Kompaktboy Condenser C (µf) Gross volume V (l) Required place LxW (mxm) Mass (kg) Discharge flow Q max (m³/h) Discharge height H max (m) Cable length L (m) Running wheel shape 1.1 W x Impeller 1.1 D x Impeller 1.5 D x Impeller 3.0 D-2P x Impeller * = these inlets may not be used in Kompaktboy 3.0 D-2P Minimum diameter of the feed opening for the complete pump station: 600 mm Maximum media temperature: 55 C Materials Tank...PE-LD Running wheel...grp (impeller), Seal carrier...pp Motor shaft...stainless steel Seals...NBR 4

5 1.4 Range of application The sewage ejection units of the type series Kompaktboy are used for the disposal (collection and conveyance) of domestic and industrial wastewater, which accumulates below the backwater level of the canal in basement apartments or one-family houses. Limits of application The pump station is not designed for continuous operation! The conveyance data mentioned on the type plate apply only to periodic duty (S3 25 %). The maximum permitted inlet quantity must always be less than the discharge flow of a pump (see type plate) 1.5 Accessories The sewage ejection units of the type series Kompaktboy are completely delivered with: - Control - Fixing material - Flexible connection for ventilation - Non-return valve (integrated in tank) - Flexible connection for pressure junction 2. Safety: ( from: VDMA sheet ) The operation manual at hand provides basic notes which must be taken into account during assembly, operation and maintenance works. Therefore, before assembly and commissioning, this operation manual must be read by the assembler as well as by the responsible personnel/operator at all costs. It always must be available on site of operation of the machine/unit. The general safety notes listed under the main point safety are not the only notes to be taken into account. Please also observe the specific safety instructions, such as those for private use, listed under other main points. 2.1 Marking of the notes contained in the operation manual The safety notes contained in this operation manual which can cause danger to persons are specifically marked by the following general danger symbol Safety sign according to DIN W 9, The following symbol warns against dangers caused by voltage Safety sign according to DIN W 8. In case of safety notes the non-observance of which can cause danger to the machine and its functioning, the word ATTENTION! is inserted. Notes that are directly attached to the machine, such as. - arrow indicating the direction of rotation - marking of liquid connections must be observed and kept in completely readable condition at all costs. 5

6 2.2 Personnel development and training The personnel responsible for operation, maintenance, inspection and assembly must have the corresponding qualifications for those types of work. Area of responsibility, competence and the surveillance of the personnel must be regulated precisely by the operator. If the personnel do not possess the necessary knowledge, they must be trained and instructed. By order of the operator, the instruction and training, if necessary, can be carried out by the manufacturer/supplier. Furthermore the operator must make sure that the personnel have completely understood the content of the operation manual. 2.3 Dangers in case of non-observance of the safety notes The non-observance of the safety notes can cause dangers to persons as well as to the environment and the machine. If the safety notes are not observed, this can result in the loss of all compensation claims. In detail, non-observance can for instance result in the following damages: - Failure of important functions of the machine/unit - Failure of the prescribed methods for maintenance and repair - Endangerment of persons through electrical, mechanical and chemical influences - Endangerment of the environment through leakage of hazardous substances 2.4 Safety-conscious way of working The safety notes listed in this operation manual, the existent national regulations on accident prevention as well as possible internal working, operating, and safety instructions of the operator must be observed. 2.5 Safety notes for the operator/user - Hot or cold machine components which could cause danger must be secured against contact by the customer. - Protection against contact with moving parts (e.g. coupling) must not be removed while the machine is operating. - Leakages (e.g. of the shaft sealing) of hazardous materials to be conveyed (e.g. explosive, toxic, hot) must be discharged in such a way that no danger arises for persons or the environment. The legal requirements must be observed. - Endangerments through electric power must be eliminated (details concerning this, see e.g. the regulations of the VDE (German Association for Electrical, Electronic and Information Technology) and the local energy suppliers). 2.6 Safety notes concerning maintenance, inspection, and assembly works The operator must make sure that all maintenance, inspection, and assembly works are carried out by authorised, skilled, and qualified personnel which are adequately informed by having thoroughly studied the operation manual. Generally, works on the machine are only to be carried out when the machine is turned off. The procedure of switching off the machine, which is described in the operation manual, must be observed at all costs. Pumps or pump units which convey media that are hazardous to health must be decontaminated. Immediately after completion of the works, all safety and protection devices must be reattached or reactivated. Before restart, the points listed in the chapter commissioning must be taken into consideration. 6

7 2.7 Unauthorised modification of the machine and fabrication of spare parts Retrofitting or modifications of the machine are permitted only after having consulted the manufacturer. Original spare parts and accessories authorised by the manufacturer ensure the safety. The use of other parts can lead to the removal of liability for the resulting damages. 2.8 Unauthorised modes of operation The operational reliability is only guaranteed, if the machine is used as intended according to chapter 1 General. The limit values stated in the data sheet must not be exceeded. 3. Transport and temporary storage 3.1 Transport The sewage ejection units of the type series Kompaktboy must not be thrown or dropped. Furthermore, they should be transported in horizontal position. 3.2 Temporary storage/conservation For temporary storage and conservation, it suffices if the unit is stored in a cool, dark, dry, and frost-protected place. The unit should be stored in horizontal position. 4. Description 4.1 General The sewage ejection units of the type series Kompaktboy are simplex units ready for connection, short-time flood-proof with gas tight and odour-tight collecting tanks made of plastics. They are operated with vertical, blockage-free sewage pumps with automatic, pneumatic level control. They are delivered with all necessary connectors Composition and mode of operation Due to the lateral inlets DN 50 and DN 100 or the upper inlet DN 50 / DN 100 (high temperature plastic sewage tube) Sewage (natural incline) is guided into the collecting tank of the sewage ejection unit Kompaktboy. In the impact pipe screwed into the top side of the tank the water rises and compresses the air in the impact pipe until the pressure actuates the dynamic pressure switch in the switch box. In doing so, the pump is switched on and transports the water from the tank through the pressure pipe into the higher located channel. A non-return valve integrated into the collecting tank prevents the backflow of the water from the pressure pipe into the tank The switching device is equipped with an alarm buzzer activated in case of a failure of the pump(s) or in case of an excessive water level in the tank. Furthermore, there are alarm contacts inside of the switching device for alarm systems (bell, buzzer, etc.) to be connected external. For the location, please refer to the circuit diagram of the switching device 7

8 5. Installation 5.1 Preparations - A correct and proper montage is pivotal for the failure-free operation of the pump station. For this reason, the following points must be observed: - The place of installation should be a well ventilated, dry and rust-free room. - The place of installation must be large enough. The ceiling heights should be approx. 2 to 2.5 m. According to DIN 1986 part 3, the following applies:...all parts of the unit...(and)...all control elements...must always be safely accessible and easy to operate....these parts of the unit must not be obstructed by stored parts, furniture, cover panels or several - The foundation of the installation room must be constructed for the possible loads depending on the dimensions of the unit. - In rooms mostly located lower, ground and leakage water is accumulated. Due to this fact, a small chamber should be located in a corner of the room, where the liquids will be accumulated and can be disposed of using a cellar drainage pump. - A ceiling hook below the place of installation of the pump station facilitates the assembly as well as possible maintenance and repair works on the pump. - Before starting the assembly, all structural and cable dimensions should be controlled and compared with the dimensions of the unit. In doing to, it is important to ensure that the continuously declining inlet pipe is located not deeper than the inlet height of the collecting tank Assembly During assembly, it is essential to ensure a zero-potential and tight installation of the pipelines and valves Placement The sewage ejection units of the type series Conpactboy will be adjusted on place of installation to existing pipelines. Here, it is placed in an exactly vertical position and fixed onto the floor using the included fixation screws. DIN part 1:...The excrements pump station must be designed in such a way that the fixing devices prevent torsion and buoying upwards Inlet The inlet pipe(s) will be connected to the included inlet bend and/or to the lateral inlets. It must be constantly declining. Inclining passages within the inlet are forbidden. The necessary inlets must be opened on the provided cutting edge using a saw. Important: When using the minimum inlet height of 180 mm it must be ensured, that the level control is adjusted in such a way, that the water level of the tank in normal operation slightly increases the lower edge up to a maximum filling of ½ of the inlet pipe before the pump switches on. In case of inlet pipes, dirt depositions in the inlet line are not excluded in this area and in extreme cases, the line could be blocked. This applies in particular to the lateral DN 50, due to the fact that they are entirely filled in every case before the pump is switched on. A connected drainage object must have its inlet minimum 180 mm above the installation level of the pump station! 8

9 5.2.3 Pressure pipe DIN part 3:...After breaking the discharge flow, backflow preventers must automatically prevent the backflow of the sewage from the pressure pipe. With the activation of the discharge, the backflow preventer must open automatically... This necessary non-return valve is already integrated into the pump station. It is recommended to mount a gate valve behind the non-return valve, in order to facilitate the cleaning and/or a possible replacement of the non-return valve The included seal ring (o-ring DN 100) for the connection of pressure sire of the pump station is mounted into the groove of the pressure outlet. The gate or, if no gate shall be used, the flange piece DN 100 included in the scope of delivery shall be fixed using 4 screws M 16. Otherwise the flange piece is mounted onto the gate. The flexible hose is plugged onto the flange piece and fixed using both included hose clamps. Now, the pressure pipe is inserted into the flexible hose and fixed using the 2 nd hose clamp. The pressure pipe must be laid in a constantly inclining manner and without unnecessary steps in a bend via the level of backedup water and afterwards constantly declining to the sewer junction. If necessary, pipelines and valves must be supported using pipe clamps or consoles Ventilation The tank ventilation (DN 75) is directly connected to the breather pipe of the building or installed through the roof Electrical connection Safety regulations All used electric devices must comply with the standard IEC 364 / VDE 0100, that means, that the electrical sockets must be equipped with earthing terminals. The electrical connection may only be effected by an electrically skilled person! The relevant VDE regulations 0100 must be respected! The mains to which the unit is connected must be equipped with a highly sensitive separate earth leakage circuit breaker IA <30 ma in front of the control or, in order to prevent a failure of the control when the earth leakage circuit breaker is activated, one earth leakage circuit breaker per pump must be installed between the control and the pump. In case of an installation in bath or shower rooms, the respective DIN VDE 0100 part 701 regulations must be respected. Please respect the regulations of the EN In case of a three-phase current supply, an external protection with automatic circuit breakers of characteristic K, in general 3-terminal mechanically blocked, must be executed. In doing so, the complete disconnection from supply is ensured and a 2- phase operation is excluded. All electrical devices, such as control, alarm sensor and power socket must be installed on a flood-proof position in dry rooms. Attention! Prior to every assembly and disassembly of the pump or other works on the unit, the unit must be disconnected from the mains. Due to an overload, the motor can overheat. Never touch the heat surfaces of the motor in case of an overheating. In case of using an extension cable, it must comply with the included connector cable concerning quality. The switching box must be mounted in such a way that the blue pneumatic hose for the pneumatic level control can be laid in a constantly inclining manner. This is indispensable to ensure a proper function of the automatic control. The connector of the simplex unit (CEEand/or earthing type) is directly connected before commissioning. The wiring diagram for the wiring of the pump station is located in the switching box and should be leaved there in order to facilitate the work of maintenance and after-sales-service staff. 9

10 6. Commissioning Before commissioning the unit, all connections must be checked for correct assembly; the non-return valve must be open. Now, the connector is plugged into the power socket and, in case of three-phase units, the rotational direction of the pump is checked. This is effected with briefly adjusting the hand/0/automatic-switch to hand and immediately actuating the stop switch. During running down of the motor, the rotational direction can be compared via the inspection glass on the upper side with the right rotational direction (directional arrow). If the pump rotates in wrong direction, two of the three phases must be changed. Disconnect the power supply before carrying out any kind of work on the unit! In case of using inlets DN 100 with 180 mm inlet height, the control is already adjusted. If inlets with higher inlet heights are exclusively used, other switching points can be adjusted on the control, in order to increase the backwater volume. Minimum inlet height Switching-off point N1 Switching-on point N2 High water HW Switching capacity 180 mm 0 cm 5 cm 7 cm 19 l 250 mm 0 cm 10 cm 13 cm 26 l 428 mm 0 cm 25 cm 29 cm 45 l Now, the button automatic is actuated and a test run is effected. For this purpose, a collecting tank is filled via the normal inlet (washbowl, toilet etc.). The unit must be automatically activated, pump out the tank and deactivated. After switching off, no water shall flow back from the pressure pipe into the tank. Depending on mounting conditions and discharge height, the follow-up time must be adjusted in such a way that the pump discharges the collecting tanks as far as possible and runs dry for a short time (loud noise during pumping). After the pumping process, the impact pipe shall not dip into the liquid (indication in the control 0 cm). The follow-up time may be adjusted in control device. During test run, all pipes and valves are checked again for tightness and tightened again, if necessary. If the pump station works properly, the switch rests in automatic position. 7. Maintenance/repair 7.1 Inspection- and maintenance intervals Inspection- and maintenance intervals according to DIN 1986 part 31: Sewage ejection units shall be checked by the operator once per month for serviceability and tightness by observing a monitoring cycle... The unit shall be maintains by an expert. The time intervals shall not be greater than 1 st ¼ year in case of units in industrial companies 2 nd ½ year in case of units in apartment buildings 3 rd 1 year in case of units in single family houses 7.2 Maintenance works Disconnect the power supply before carrying out any kind of work on the unit! 10

11 7.2.1 Collecting tank Open the inspection cover and squirt the tank using a hose, in order to lose sediments from the tank walls Non-return valve Close the gate valve of the pressure pipe, if existing. For exhaustion of sewage from the non-return valve, there is a drilled hole with a 1 internal thread and equipped with a dummy plug on the right side of the tank. On this point, it is possible to install e.g. a F+E stop cock. Open the inspection cover and clean the non-return valve from the inside Miscellaneous All continuative maintenance works must be effected by the after-sales-service. The following substances must not be fed: Solid materials, fibrous materials, tar, sand, cement, ash, rough paper, paper towels, paper boards, rubbish, garbage, offal, greases, oils. All drainage objects lying above the backwater level (EN ). Sewage with dangerous substances (DIN ), e.g. fatty sewage in industrial kitchens. The inlet may only be effected through a fat separator according to DIN

12 8. Malfunctions; causes and elimination Disconnect the power supply before carrying out any kind of work on the unit! In order to disassemble the motor unit from the tank, only the 8 Allen head screws (pos. 13 of the spare parts list) must be loosed. The 4 hexagon screws (pos. 5 of the spare parts list) must not be loosed, because otherwise, the seal ring will be destroyed, oil will escape and the guarantee expires! Failure Cause Removal - Voltage too low, no voltage - Check the supply 1. No motor rotation 2. Motor rotates but does not convey 3. Motor rotates and switches off 4. Motor does not switch off - Faulty power supply - Corrective measure - Electric cable defective - Replacement/after-salesservice - Failure in the condenser only in case of a 230 V pump - Replacement/after-salesservice - Running wheel blocked - Cleaning - Motor protection is switched off due to - Check/after-sales-service overheating, blockage, voltage failure - Control failure - Check/after-sales-service - Pneumatic hose and/or connection not tight - Check/replacement - Motor defective - Replacement/after-salesservice - Running wheel blocked or worn - Cleaning/replacement - Non-return valve blocked - Cleaning - Gate valve blocked or worn - Cleaning/open - Pressure pipe blocked - Cleaning - Intake fitting blocked - Cleaning - Wrong rotational direction - Corrective measure - Water deficiency in the tank - Deactivation/after-salesservice - Tank ventilation blocked - Cleaning - Pump housing ventilation blocked - Cleaning - Faulty voltage and/or variable - Corrective measure/after-salesservice - Over current release wrongly adjusted - Adjust it correctly - Power reception too high - After-sales-service - Control failure - After-sales-service 9. Warranty As manufacturer, for this product we provide a warranty of 24 months from date of purchase. Your sales receipt passes for verification. During that warranty period, we gratuitously remedy all deficiencies which are attributed to material or fabrication defects by either repairing the unit, or by replacing the defective parts (to our choice). Defects which are attributed to misuse or wear are excluded from warranty. We will assume no responsibility for consequential damages that are caused by a breakdown of the unit. 10. Technical modifications We reserve the possibility of technical modifications for the purpose of further development. 12

13 Appendix A: Installation example Flange piece DN110 with flexible connection piece Gate Flexible connection piece DN65 for the ventilation pipe 13

14 Appendix B: Dimensios Kompaktboy Revision hole Integrated nonreturn valve 1 Exhaustion Non-return valve 1 ½ connection hand diaphr. pump Inspection cover Impact pipe Pressure outlet 14

15 Appendix C: Sectional drawing and spare parts list Pos. Qty. Designation Article no. 2 1 Motor unit 1.1 kw-230 V with impeller Motor unit 1.1 kw-400 V with impeller Motor unit 1.5 kw-400 V with impeller Motor unit 3.0 kw-400 V with impeller O-ring 190 x Seal carrier Hexagon head screw M 12x25 ZE Oil filling 0.5 l Seal ring Fitting key ZE Impeller (1.1 kw) Ø 175 mm Impeller (1.5 kw) Ø 190 mm Impeller (3.0 kw) Ø 125 mm Running wheel cover compl. incl. pos.10,11,24 ZE O-ring 190x5 ZE Allen head screw M8x25 ZE Oil filling screw M 8x10 ZE Angle nozzle R 3/ Ventilation hose 0.25 m Hose clamp ZE Switching device simplex unit Condenser 50 µf for three phase current pump 1 Impact pipe cpl. simplex unit Control hose 5.5 m Collecting tank Kompaktboy with RSK Substitution gate for non-return valve E/ Seal for inspection cover of the non-return valve Inspection cover of pump station with seal

16 2010 by Zehnder GmbH 16