Bennett Pump Company SB-100 Meters

Transcription

1 Bennett Pump Company SB-100 Meters Operation, Service, and Parts Manual Rev B 11/17/16 Only Trained Personnel May Work on This Equipment READ THIS MANUAL This manual has important information for safe installation and operation of this equipment. Read and understand this manual before applying power. Keep this manual and tell all service personnel to read this manual. If you do not follow the instructions, you can cause bodily injury, death, or damage to the equipment. Bennett 1218 E. Pontaluna Road, Spring Lake, MI USA ~ Outside USA sales@bennettpump.com ~

2 The material included in this installation manual is accurate at the date of publication and may change without notice. The intent of this manual is to assist. If further assistance is required, please contact the Bennett Technical Service Department at Bennett Marketing Services can be contacted by mail, facsimile, telephone or at the locations specified below: Bennett Pump Company Marketing Services 1218 East Pontaluna Road Spring Lake, MI Telephone from USA Telephone from outside USA , Extension 287, or 269 Facsimile: or Website: For new manuals, visit our web page at IMPORTANT Examine the shipment immediately upon arrival to make certain there has been no damage or loss in transit. Bennett Pump Company, as shipper, is not liable for the hazards of transportation. Please make damage claims directly to the truck line. Revision History: Revision Date Description A Original Document B Update Kit Part Numbers, add certifications and approvals, add mechanical and electronic calibration information. Bennett 1218 E. Pontaluna Road, Spring Lake, MI USA ~ Outside USA sales@bennettpump.com ~

3 Table of Contents Table of Contents Safety Instructions ii 1 Standard Features... 1 Technical Specifications... 2 Approvals... 2 SB-100 Series Models... 2 Features and Constructions... 3 Abbreviations and Acronyms... 3 Dimensions & Mounting... 4 Theory of Operation... 5 Basic Concept... 6 Calibration 7 SB-100 Mechanical (M-Cal Option)... 8 Troubleshooting & Repair 11 Symptoms SB-100 Maintenance Parts 13 To Place an Order for Parts SB-100 Mechanical Meter SB-100 Electronic Meter SB-100 Meter Parts List Kit Lists i

4 Safety Instructions Safety Instructions For safe installation of this equipment, read and understand all dangers, warnings, and cautionary information. Save this safety information in a readily accessible location. Look for the following warnings throughout the manual: Red and White DANGER means: If you do not follow the instructions, severe injury or death will occur. Orange and Black WARNING means: If you do not follow the instructions, severe injury or death can occur. Yellow and Black CAUTION means: If you do not follow the instructions, damage can occur to the dispenser. DANGER PELIGRO DANGER FIRE, EXPLOSION, INJURY, OR DEATH WILL OCCUR IF FUEL FILTERS ARE CHANGED BY UNTRAINED PERSONNEL. MAKE SURE, ONLY TRAINED PERSONNEL CHANGE FILTERS. TO PREVENT INJURY TO YOU FROM VEHICLES AND ONLOOKERS, ALWAYS PLACE A BARRIER AROUND THIS EQUIPMENT BEFORE PERFORMING SERVICE OR MAINTENANCE. GASOLINE IS FLAMMABLE. NO SMOKING OR OPEN FLAME. DISCONNECT ALL POWER AND RELIEVE PRESSURE TO THIS EQUIPMENT AND ASSOCIATED SUBMERGED PUMP(S) DURING INSTALLATION, SERVICE, OR ANY MAINTENANCE I.E., CHANGING FILTERS. WARNING ADVERTENCIA MISE EN GARDE You must have training in the installation, service, or maintenance of this equipment (dispenser, pump, console, control box, or submerged pump) before working on it. Maintenance repairs must be done by authorized personnel only. Warranty work may only be performed by Bennett certified technicians. To prevent electric shock, keep the electrical parts of the dispenser dry. Electronic components are static sensitive. Use proper static precautions (e.g. static straps) before working on the equipment. The emergency shut-off valve (also called the fire valve, shear valve, or impact valve) must be closed when service or maintenance is performed on this equipment. You must have training in the operation and programming of this dispenser before using it. READ THE OPERATORS MANUAL. Make sure this equipment is correctly grounded. Failure to do will cause injury or damage equipment or improper operation. Improper grounding voids the warranty. Do not operate the equipment as a dispenser unless it is completely assembled. CAUTION PRECAUCIÓN MISE EN GARDE Do not drill holes in fuel dispensers. Holes can cause failure of the electronic equipment. THE WARRANTY WILL BECOME VOID. Use only adhesive backed sign mounting brackets.!! READ AND UNDERSTAND ALL WARNING LABELS ATTACHED TO THE DISPENSER!! ii

5 The SB-100 meter is the standard product for Bennett Dispensers. It can drive mechanical and electronic computers at any flow used in a basic gasoline dispenser. The SB-100 meter is a precision device built to maintain.3% accuracy for flow rates from 1.3 GPM (5 LPM) to 26 GPM (100 LPM). The SB-100 is a volumetric meter employing four pistons with seals and associated chambers. During the first year of use, the SB-100 meter's calibration should be checked upon installation, after 90 days and after 180 days in order to insure accurate measurement. After the break-in period, semi-annual calibration checks are all that is required. The SB-100 meter is a compact, lightweight unit built with the following main objectives: Excellent accuracy over a wide range of flows. Very good durability of performance and life up to 2 million gallons (7,500,000 liters) under laboratory conditions. Flexible mounting capability for layout in the dispenser (several product outlet positions). Minimal numbers of internal components to assemble or repair. Concept takes care of potential requirements for a meter: o o Adaptable to temperature compensation system Compatible with alternate fuels with up to 15% additives. Certain models available for higher fuel blends, contact factory for details. The positive displacement meter uses the general principle of four horizontal, single effect pistons equipped with "cup seals" moving in stainless steel sleeved cylinders and driving a vertical crankshaft. The crankshaft also of stainless steel is fitted with stainless steel connecting rod rollers and self-lubricated bearings throughout for minimum friction and maximum corrosion resistance. The patented SB-100 meter, patent number , is compatible with the Bennett T-75 Pumping Unit and is used in all of our electronic and mechanical dispensers sold worldwide and offers advanced features. At Bennett, we consider the meter the key to accurate product measurement and the fundamental source of information for the marketer s inventory systems. The SB-100 is designed to provide years of accurate and reliable service starting with the first liter! Standard Features 1. Volumetric, four-piston design. 2. Excellent accuracy over a wide range of flow rates. 3. Small number of internal components for easy field service. 4. Compatible with up to 15% ethanol/methanol blends, AL version available for higher concentrations 5. Mechanical calibration dial with seal pin. 6. Electronic calibration (e-cal) models available for increased accuracy. 7. U.S. Gallon or Liter models available. 8. Flanged bottom inlet for direct connection to T75 and T75HD Bennett Pumping Unit manifold options. 9. Flanged outlet port for direct connection to Bennett Optional outlet manifolds. 10. Adjustable outlet orientation and multiple mounting arrangements to fit most all alignment options. 1

6 Technical Specifications Crankshaft Eccentricity (inches/millimeters) in. / mm Cylinder Diameter (inches/millimeters) in. / 72 mm External Dimensions Mechanical - Horizontal in. x 8.66 in. / 200 mm x 220 mm Electronic - Horizontal in. x 7.87 in. / 200 mm x 200 mm Mechanical and Electronic Vertical (Including Drive) in. / 189 mm Flow Rate Capacity within +/- 0.3% Accuracy Minimum Flow (gallons per minute / liters per minute) gpm / 5 lpm Maximum Flow Objective (gallons per minute / liters per minute) gpm / 100 lpm Minimum Mechanical Adjusting Device Increment (percent) % Outlet Shaft Diameter (inches / millimeters) in. / 10 mm Rotation Direction of Outlet Shaft (top view)... Clockwise Stroke (Pistons 1 & 4) Adjustable Between (inches / millimeters) in. / mm And (inches / millimeters) in. / mm Volume per revolution (liters / gallons) liters / gallon Weight (pounds / kilograms) lbs. / 4.54 kg Working Pressure psi / 3.5 bar Approvals U.L Listed Flammable Liquid Meter Certificate Number MH28133 Report Reference MH Approved in USA by N.T.E.P., Certificate #91-095A1 Approved to Comply w/ OIML R117 ZR 141/ Other Weights & Measure and Safety approvals available, contact Bennett Pump at the location below. Bennett Pump Company Jim Biesecker (Component Business Manager) 1218 East Pontaluna Road Spring Lake, MI Telephone from USA Telephone from outside USA , Extension 262 or Facsimile: JBiesecker@bennettpump.com or salesintl@bennettpump.com Website: SB-100 Series Models SB-100 Up to 15% Methanol, Ethanol, or MTBE. SB-100 AL Up to 100% Methanol or Ethanol SB-100 E Electronic Calibration & 15% Blends SB-100 E AL Electronic Calibration & 100% Alcohol AL = For use with Gasoline/Ethanol blends with nominal ethanol concentrations up to 85%. E = Electronic Calibration 2

7 Features and Constructions The meter is a positive displacement, four-piston device featuring a rotary distributor valve and "cup seal" pistons. Because of these features, the meter shows superior accuracy and repeatability by eliminating internal product slippage. The composition of the "cup seal" piston is such as to provide long life and low calibration drift. The SB-100 Meter features improved linearity allowing the calibration to remain within tolerance from 1.3 GPM (5 LPM) flow rate to 27 GPM (100 LPM). Currently the standard SB-100 Meter is compatible with up to 15% ethanol/methanol blends. The SB-100 can be manufactured of materials that are compatible with M85 and 100% methanol. The SB-100 is fully compatible with Methyl tert-butyl Ether (MTBE) additives to 15% concentrations. The SB-100 weighs only 10 pounds (4.7 kg) making service, installation, and handling very easy. The SB-100 Meter is the result of seven years of product development. Abbreviations and Acronyms Term E-CAL FCC GPM HZ IFC IN. LPM M-CAL MM NEC NIST NO. QTY UL W&M Description Electronic Calibration Federal Communications Commission Gallons Per Minute Hertz International Fire Code Inches Liters Per Minute Mechanical Calibration Millimeters National Electrical Code National Institute of Standards and Technology Number Quantity Underwriters Laboratories, Inc. Weights and Measures 3

8 Dimensions & Mounting 4

9 Theory of Operation The meter body (1) is cast aluminum with a gasket flange at the base for rigid mounting with other components using four to six screws. The cylinder covers (2, 3) are also cast aluminum with an O-ring seal and each is secured to the body by four screws. The calibrator cover (3) has a threaded shaft extending through it that limits the piston stroke to effect calibration. The shaft is sealed with an O-ring Note: Electronic calibration meters do not have the calibrator cover (3). Fastened to the top of the meter body is a cast aluminum collector housing (4), which can be assembled in several outlet positions. An O-ring and four screws make the seal and connection. Extending through the top of the collector is the output of the crankshaft that is sealed against leakage by a lip seal (5) held in place by a retainer (6) and three screws. Refer to the circled numbers in Figure 1 for description locations. PRODUCT OUTLET PRODUCT INLET Figure 1 - Mechanical Meter Shown 5

10 Basic Concept 2 The liquid to be measured enters the bottom part of the meter body (1) and pressure seals the rotating distributor (2) down on its mating surface through a diaphragm (3) and a countervalve (3). The pressure differential on the two sides of pistons 1 and 2 pulls the connecting rods (4) and makes the crankshaft (5) turn clockwise (top view). The crankshaft drives the distributor, which changes the distribution of liquid; piston 2 and 3 become active, then 3 and 4 and finally 4 and 1 before the cycle starts again. Each cylinder is closed with cover (6), one of them being fitted with a calibrating device (7-mechanical only) that allows adjustment of the stroke of the corresponding piston to get the exact value of the volume per revolution dispensed by the meter. The crankshaft and connecting rods are supported by self-lubricating bearings to minimize the wear and make the moving parts run smoothly. The crankshaft may drive a mechanical computer or an electronic pulser that can be fixed directly to the collector (8) which forms the upper part of the meter Figure 2 - Flow Diagram 6

11 Calibration Calibration The Bennett SB-100 Meter is built to maintain accurate measurement under normal operating conditions. The meter is a positive displacement device with rods and pistons, which require a break in period. The meter is calibrated at the factory using a solvent for safety purposes, and MUST BE calibrated after it has been installed. We strongly suggest recalibration of the meter after a 90-day break in period. The accompanying Meter Accuracy Curve is typical of the SB-100; 0.3% accuracy from 1.3 gpm (5 lpm) to 27 gpm (100 lpm). 0.3 Tenths of 1% Deviation Based on metering gasoline with an approximate viscosity of 30 SSU Flow Rate (gpm) Typical Meter Accuracy Curve 7

12 Calibration SB-100 Mechanical (M-Cal Option) Calibration Calibration of the SB-100 mechanical meter is achieved by adjustment of the dial and screw assembly on the cover attached to cylinder No.1. A clockwise adjustment decreases delivery while counterclockwise increases delivery. Total adjustment is +/- 15 cubic inches (+/- 240 ml) in minimum increments of 0.05%. Once the meter is adjusted to zero, a pin is inserted through the dial and into the cover and wire sealed through a cross drilled hole in the pin. Mechanical Calibration has been simplified by placing the calibration dial wheel on the piston cover face, out where it is easily accessible as shown in Figure 3. The minimum mechanical calibration adjustment is 0.05%. Each SB-100 meter is provided with the following calibration information: The dial adjusting cover has (+) and (-) arrows to indicate the correct direction to rotate the dial to either increase or decrease delivery. A self-adhesive metal label listing the minimum incremental adjustment is attached to the collector housing immediately above the adjusting dial. Figure 3 - SB-100 Mechanical 8

13 Calibration Calibration The dial cover has two pin hubs, one to the left of the shaft and one to the right. The seal pin may be inserted in either hub as shown in Figure 4. The smallest adjustment (.6 cu. in.) occurs when the pin is pulled from one side and inserted in the other side by moving the dial the least amount or half a hole. A 1.2 cu. in. adjustment is made by pulling the pin and turning the dial until the next adjacent hole aligns with the same hub and reinserting the pin. To calibrate the meter, follow this procedure: 1. Measure the actual delivery of the meter at fast flow in an accurate test measure. Dispense a minimum of 5 gallons (20 liters). 2. Cut and remove the existing seal wires and remove the seal pin. See Figure Turn the dial the necessary amount in the (+) or (-) direction to increase or decrease the quantity of fuel delivered. 4. Re-insert the seal pin in the desired pin hub. Figure 4 - Dial Cover and Seal Pin 5. Dispense 5 gallons (20 liters) of fuel to allow the meter to adjust to the new settings. Do not make any adjustments based on this delivery. 6. Make sure the meter is properly calibrated. Dispense another 5 gallons (20 liters) of fuel into an official test measure to check the calibration. EXAMPLE 1 1. A fast flow test at 11 GPM shows a +3 cu. In. reading in a five-gallon test measure. 2. Remove the existing seal and pin and turn the dial clockwise (-) five minimum adjustments (half holes) and reinsert the pin. 3 cu.in. = 5 half holes (-) CW.6 cu. in./adjustment 3. Test and Reseal. EXAMPLE 2 1. A fast flow test at 11 GPM shows a -2 cu. in. reading in a five-gallon test measure. 2. Remove the existing seal and pin and turn the dial counterclockwise (+) three minimum adjustments (half holes) and reinsert the pin. 2 cu.in. = 3 half holes (+) CCW.6 cu. in./adjustment 3. Test and Reseal. 9

14 Calibration SB-100 Electronic (E-Cal Option) Calibration Electronic calibration is a simple method to calibrate the meters in the dispenser. This method uses a mathematical algorithm in the software to account for meter wear rather than mechanical methods to limit the piston throw within the meter. This method also eliminates the parts associated with mechanical calibration in the meter. The result is a more symmetrical meter that will be intrinsically more accurate. Figure 5 - SB-100 Electronic Meter WARNING You must perform the E-Cal prior to dispensing fuel. If the E-Cal is not performed properly, the dispenser will produce a Calibration error. Prior to entering E-Cal Mode, you must slide a switch on the electronics to the right on the CPU Board to gain access. During normal operation, this switch is in Normal Operating Mode. If you attempt to dispense with the switch in E- Cal Mode, the dispenser will give you an Error. Notes: Before performing the calibration gallons of fuel needs to be dispensed from each meter. All programming must be performed including pricing. The E-Cal switch much be in calibrate mode. There are three types of Calibration. Refer to your dispenser operator s manual for electronic calibration instructions. Calibration procedures vary. Refer to the electronic calibration formula located below. Basic Calibration For test cans with a sight glass that is graduated in units of cubic inches or centimeters (milliliters). Operation Calibration For test cans with a sight glass that is graduated in percentage units. Direct Percentage Test can used only to verify calibration or used to zero or overwrite the E-CAL setting. 10

15 Troubleshooting & Repair Troubleshooting & Repair CAUTION: This section provides basic troubleshooting and component replacement procedures. It is not a substitute for technical training. Improper handling of equipment and/or improperly performing the included procedures could damage your DISPENSER. Symptoms The following section provides basic troubleshooting solutions based on the problem encountered with your meter. The troubleshooting procedures are written in progressive steps. As each step is completed, check the operation of the equipment. If the step repaired the problem, discontinue troubleshooting the symptom. Symptom Cause Solution The meter will not run-fuel flows A. Diaphragm is damaged A. Replace the Diaphragm out of the nozzle. B. Broken Rod B. Replace Meter The meter will not run-no fuel flows out of the nozzle. Nozzle is fuel open but delivers only 2 gpm (7 lpm) or less. Meter turns jerky at slow flow. Runs but hesitates. Meter calibrates high at fast flow. Meter Calibrates high at slow flow, but calibrates normal at fast flow. A. Solenoid valve not functioning B. Filter is plugged C. Pumping unit not operating properly D. Faulty impact/safety valve E. Inlet check valve blocked (suction pump) F. No fuel in storage tank G. Distributor is locked A. Check valve & replace if necessary. B. Clean all filters and/or replace. C. Verify proper operation & replace if necessary D. Replace/repair impact valve E. Clean check valve and/or replace F. Fill storage tank with fuel G. Replace the distributor (KR446). Note: If corrosion is noticed during kit installation, clean tank, and find source of corrosion. A. Diaphragm or distributor is damaged A. Replace the diaphragm and distributor (KR446) A. Diaphragm or distributor is damaged A. Replace the diaphragm and distributor (KR446) A. Diaphragm is damaged. A. Replace diaphragm (KR446) B. Damaged or worn pistons. B. Replace all pistons (KR436) C. Worn Crankshaft rollers. C. Replace rollers ( kit) A. Diaphragm is damaged. B. Damaged or worn pistons. C. Leakage between distributor and valve plate. A. Replace diaphragm (KR446) B. Replace all pistons (KR436) C. Damaged countervalve assembly, distributor, and countervalve. Replace components (KR446). See lapping instructions in manual Part Number N Meter calibrates low at slow A. Friction A. Replace diaphragm (KR446) flow. Over delivery and out of tolerance difference between A. Dirty or gummed pistons and/or piston chambers. A. Remove cylinder covers. Remove screwholding piston to connecting rod. Use fast and slow delivery. vise grips to secure the center hub of the piston and pull straight out. Clean piston seal and piston chamber using mineral spirits. Re-assembly in reverse order. B. Damage or worn piston seals. B. Replace all pistons. Use piston repair kit KR Leakage at the output shaft. A. Top lip seal is damaged. A. Replace top lip seal s Meter calibration drifts positive over time. A. Worn crankshaft rollers A. Replace crankshaft roller ( kit) Calibration dial is turned all the way In and still cannot calibrate the meter. A. Worn crankshaft rollers B. Diaphragm Damaged A. Replace crankshaft rollers ( kit) B. Replace the diaphragm (KR446) Meter will not calibrate. A. Diaphragm and/or distributor is A. Replace diaphragm/distributor (KR446) damaged. B. Damaged or worn pistons B. Replace all pistons (KR436) C. Worn crankshaft rollers C. Replace crankshaft rollers ( kit) Large over delivery amount. A. Damaged distributor and/or diaphragm. A. Use distributor/diaphragm kit KR

16 Troubleshooting & Repair SB-100 Maintenance Troubleshooting & Repair The Bennett SB-100 is a precision instrument. Flatness tolerance specifications for distributor, valve and counter valve are 5 light bands (50 millionths of an inch). To ensure the continued integrity of the precision parts during the life of the meter, proper filtration before the meter is essential. Filters protect the meter, the pumping unit (if present), flow control solenoids, the nozzle, and ultimately the customer s automobile components. Filters should be replaced or cleaned on a regular basis or anytime the flow rate has dropped by a noticeable amount. Bennett dispensers or any dispensers using Bennett meters should NEVER be operated without proper filtration. Failure to maintain the filtration in the Bennett dispenser voids the warranty protection offered by Bennett. Note: Good filtration practices extends the life of the Bennett hydraulic components. CAUTION: Under no circumstances should the meters be exposed to filtration larger than 70 Micron. Figure 6 - Filter Replacement 12

17 Parts Parts This section covers the SB-100 mechanical and electronic parts. To Place an Order for Parts To place an order for parts please contact us by mail, , phone, fax, or web using the information provided below. Note: Verbal orders cannot be accepted. A signed purchase order must be faxed or ed to the Bennett Order Entry Department at or customerservice@bennettpump.com. Bennett Pump Company Marketing Services 1218 East Pontaluna Road Spring Lake, MI Telephone from USA Telephone from outside USA , Extension 287 or 269 Customer Service Telephone , Facsimile sales@bennettpump.com or salesintl@bennettpump.com Website: For new manuals, visit our web page at All orders must include the following information: Note: Many electronic circuit boards have a factory-rebuilt equivalent. All rebuilt boards have a part number prefix of RB. Please refer to the Distributor Policy Manual for program terms and details. The part number, description, and quantity required. Provide a complete model and serial number, including the date code when ordering parts. The serial tag can be found inside the upper cabinet on side 1 of the dispenser. Rebuilt parts must be used for warranty claims. Rebuilt exchange program parts are identified by a RB prefix to the part number. Your company s name and address (if different from the shipping destination) for billing purposes. The complete ship to address. A purchase order number for order identification. Serial Number Identification The SB-100 meter can be identified by the date code on an adhesive metallic tag, metal Part Number/Serial Tag, or an adhesive white tag as shown in Figure 7. The serial number #3E shown in Figure xx consists of a number 1 to 12 to designate month of manufacture followed by a letter to designate year. For example 3E is the date code signifying manufacturing in March (month 3), 2003 (E = 2003). Current models use the white adhesive tag as shown below. Note: Letters I, O, and Q are not used. Figure 7 - Serial and Model Number 13

18 Parts Parts SB-100 Mechanical Meter Refer to the SB-100 Meter Parts Lists on page 16 and 17 for part numbers, description, and comments. Figure 8 - SB-100 Mechanical Meter 14

19 Parts Parts SB-100 Electronic Meter Refer to SB-100 Meter Parts Lists on pages 16 and 17 for part numbers, descriptions, and comments. Figure 9 - SB-100 Electronic Meter 15

20 Parts Parts SB-100 Meter Parts List Refer to the SB-100 Mechanical and Electronic views on the previous pages for reference number locations. Note: Not all parts are shown. Item Part No. Description Comment 1 N/A Lead Seal Wire Please Call for details 2 N/A Universal Link Please Call for details 3 H Half Coupling Unthreaded See Kit List 4 H Half Coupling Threaded 5 H Screw 6 A Screw, Flat Head M X 8 mm 7 N Shaft Seal Retainer S Shaft Seal 9 A Screw, Hex Head M6-1.0 X 20 mm 9 N Screw, Hex Head M6-1.0 X 20 mm with Seal Hole 10 A O-Ring, Square Section 11 N Collector Cover Collector Cover High Alcohol 12 A O-Ring, Square Section 13 N Gasket Spring 15 A Screw, Fil Head M4-0.7 X 10 mm Stainless Steel 16 N Inner Diaphragm Retainer Diaphragm 18 N Gasket 19 N Counter Valve Counter Valve Assembly 21 N Outer Diaphragm Retainer 22 A Screw, Pan Head M5-0.8 X 12 mm Collector Cover Assembly Collector Cover Assembly High Alcohol 24 N Drive Pin 25 N Distributor 26 A Retaining Ring 27 A Washer Crankshaft Support Meter Body Assembly Meter Body Assembly High Alcohol 29 N Roller & Bearing Assembly 30 A Washer 31 A Lock Nut 32 N Crank Shaft Assembly Gallons 32 N Crank Shaft Assembly Liters Pin Cylinder Cover Gallons Pin Cylinder Cover Liters Pin Cylinder Cover High Alcohol Gallons Pin Cylinder Cover High Alcohol Liters 33 N Cylinder Cover (Non Pin) 34 A O-Ring, Square Section 35 N Piston Screw, Hex Head With Nylon Patch (also use with High Alcohol) 36 N Piston Assembly Piston Assembly High Alcohol 38 N Connecting Rod 39 A Retaining Ring 40 N Calibrating Cover Calibrating Cover High Alcohol 16

21 Parts Parts Item Part No. Description Comment O-Ring 42 N Calibrating Diag & Screw Assembly 43 N Seal Pin 44 N Calibration Cover Assembly Calibration Cover Assembly High Alcohol Calibration Cover Assembly Temperature Compensation Gasket, Meter Inlet (Cork) Not Shown - Obsolete Seal Square Not Shown 46 N902401S Valve Plate Not Shown 47 A Screw, Valve Plate Not Shown 48 A DU Bearing, Meter Body Not Shown, for meters built since N DU Bearing and Retainer, Meter Body Not Shown, for meters built since 1995 Kit Lists Refer to the SB-100 Mechanical and Electronic views on the previous pages for item number locations and description. Part Number Description Comment Kit, SB-100, V'Plate/C'Valve Replacement Includes 1 each of items 8, 10, 12, 13, 14, 20, 25 & 46 KR Kit, SB-100 Piston Retail, 4 Per Includes 4 of items 34, 35, & 36, 1 each of 10 & Kit, SB-100 Piston Retail, Alcohol Meters Includes 4 of items 34, 35, & 36, 1 each of 10 & Kit, Crankshaft Bearing Replacement Includes 2 of item 29, 1 ea. of 10, 31 & Kit, Lower Hydraulic Gallon SB-100 Includes 4 of items 34, 35, & 36, 1 ea. of 8, 10, 12, 26, 32, 45 & Kit Lower Hydraulic Gallon SB-100 Alcohol Includes 4 of items 34, 35, & 36, 1 ea. of 8, 10, 12, 26, 32, 45 & Kit Lower Hydraulic Liter SB-100 Includes 4 of items 34, 35, & 36, 1 ea. of 8, 10, 12, 26, 32, 45 & Kit Lower Hydraulic Liter SB-100 Alcohol Includes 4 of items 34, 35, & 36, 1 ea. of 8, 10, 12, 26, 32, 45 & 48 KR Kit, SB-100 Diaphragm/Distributor Includes 4 of item 15, 1 ea. of 8, 10, 12, 13, 14, 17, 25 & Kit, SB-100 Meter Coupling Includes items 3, 4 & Kit, Tools for Du Bearing Replacement Field Du Bearing Install/Removal Tool Kit, Meter Gallon Pin Covers M-Calibration Includes 3 of items 33 & 34, 2 ea. of 29, 1 ea. of 10, 8, 38, 48, Kit, Meter Gallon Pin Covers E-Calibration Includes 4 of items 33 & 34, 2 ea. of 29, 38, 1 ea. of 10, 8, 45, Kit, Meter Liter Pin Covers M-Calibration Includes 3 of items 33 & 34, 2 ea. of 29, 1 ea. of 10, 8, 38, 48, Kit, Meter Liter Pin Covers E-Calibration Includes 4 of items 33 & 34, 2 ea. of 29, 38, 1 ea. of 10, 8, 45, 48 Kits - SB-100 meters built after 1995 Part Number Description Comment KR Kit, SB-100 Meter, Crankshaft, Gallons Includes 4 of item 34, 1 ea. of 8, 10, 12, 26, 32, 45 & 48 KR Kit, SB-100 Meter, Crankshaft, Liters Includes 4 of item 34, 1 ea. of 8, 10, 12, 26, 32, 45 & Kit SB-100 Meter External Gasket/Seals Includes 4 of item 34, 1 ea. of 8, 10,12,41, 45 Kits SB-100 meters built before 1995 Part Number Description Comment KR044701* Kit, SB-100 Meter, Crankshaft, Gallons Includes 4 of item 34, 1 ea. of 8, 10, 12, 26, 32, 45 & 49 KR044702* Kit, SB-100 Meter, Crankshaft, Liters Includes 4 of item 34, 1 ea. of 8, 10, 12, 26, 32, 45 & 49 * Obsolete 17

22 Bennett 1218 E. Pontaluna Road, Spring Lake, MI USA ~ Outside USA sales@bennettpump.com ~