HR-A-03, HR-A-05. Full manual EN OPERATION AND MAINTENANCE

Transcription

1 EN ISIS re c o v e r HR-A-03, HR-A-05 Full manual EN OPERATION AND MAINTENANCE 9

2 1. NEŽ ZAČNETE 1. BEFORE YOU BEGIN 2. VYBALENÍ 1.1 INSTRUCTION MANUAL For better orientation, the following symbols can befound in the text of the instruction manual. The following table describes the symbols and their meaning. Symbol Meaning 1.2 INFORMATION REGARDIN THE UNIT AND INSTALLATION ISIS Recover is a cased heat recovery unit for use in transferring air and the recovery of heat from the air taken from the interior to the fresh air transferred into the interiorwithout the two being mixed. The ventilation unit is particularly suitable for ventilating smaller appartments, offices, and other facilities. ATTENTION! YOU WILL NEED INFO TECHNICAL INFORMATION Warning or notice Important instructions Practical tips and information Further detailed technical information Reference to another section /part of the instruction manual/ TECHNICAL INFORMATION The ventilation unit is designed for operation in an interior, dry environment with a surrounding temperature, ranging from +0 C up to +40 C, with relative humidity up to 90%, for inlet of airfree of rough dust, grease, chemical vapours and other impurities with a temperature ranging from -20 C up to +40 C and with a relative humidity up to 90%. The unit installed in the pipeline is with IP20 electrical protection. Prior to operation, read carefully the section for the safety operation of the ventilation unit where you can find all the instructions for safe and correct product use. This instruction manual contains important instructions for the provision of the correct operation and maintenance of the ventilation unit. Read and observe the following instructions prior to operation and maintenance of the ventilation unit. The manufacturer reserves the right for any amendments including the technical documentation prior to previous notification. Keep the manual safe for future reference. Consider the manual instructions as part of the product. 2. OPERATION 2.1 Start of the unit and setting of revolutions 10

3 2. VYBALENÍ 2. OPERATION 2. OPERATION 2.2 Start and setting of heating 2.5 TERMINATION OF UNIT 2.3 Termination of hetaing 3. MAINTENANCE 3.1. FILTER REPLACEMENT YOU WILL NEED Imbus key, size 3 mm The need for a filter replacement is indicated on the display of the remote control FULL INSTALLATION Other functions Filter replacement Unscrew the revision lid HR-A Replace the air filter for the supply or outlet unit and the symbol will automatically disappear. HR-A

4 3. MAINTENANCE Remove the air filter. Insert a new air filter and screw on the revision lid In the event that you have installed the pressostat for indication of the blocked filter, the warning symbol will disappear from the display automatically. ATTENTION! In the event that the filter will not be cleaned properly (replaced), the functioning of the unit can be reduced and the ventilator can be damaged. 3.2 PERIODICAL CLEANING OF THE VENTILATION UNIT YOU WILL NEED Imbus key, size 3 mm Vacuum cleaner Small brash Cloth Non-aggressive cleaning product (soap water) Clean the ventilation unit, using a vacuum-cleaner, a small brush, a cloth and soapy water. Do not clean the ventilation unit with the following: Sharp objects, aggressive chemicals, solvents, abrasive cleaning products, pressured water, pressured air or steam. ATTENTION! Prior to maintenance, service or repair, the ventilation unit must be disconnected from the power supply and switched off, using the service switch which set at the 0 position (switched off) 4. FAULT REPAIRS 12 We recommend that regular checks of the ventilation unit are carried out accompanied with cleaning each half a year; however the interval must be adjusted according to the actual conditions. We recommend the overall cleaning of the unit at least once a year. In the event that the unit is not operated for a long period of time, we recommend that the unit is switched on at least once every six months for one hour. If you are not sure which steps should be taken, do not proceed with the repair and call out for a professional service! In the majority of cases, the fault is signalled on the controller see the page 13.

5 4. FAULT REPAIRS Flashing frequency Unit behaviour Anticipated problem Solution 3x in 10s The unit is not running Faulty channel sensor Check if the sensor is properly fixed in the regulation terminals. In the event that the sensor is damaged, replace it. 4x in 10s The unit is exceptionally noisy, vibrate The air filters are dirty Check if the filters are not dirty. If they are dirty and the remote control did not display a notification of such, install new filtration inserts The supply or output pipes are blocked Check the suction and exhaust pipes for blockage. (blocked suction lamellas, blocked distribution elements, closed valves etc.) 6x in 10s The unit is running Faulty outlet sensor Check if the sensor is properly fixed in the regulation terminals. In the event that the sensor is damaged, replace it. 8x in 10s The unit is not running Disconnected data cable Check if the controller is properly connected or if communication cable is not damged Interrupted power supply Check if the power supply of the outlet unit was not out of order. The unit cannot be started The electrical cable is not connected properly. Check all the connections of the electrical cables leading to the unit. The power supply was disconnected or it does not achiever required values. Measure the power supply at the connecting terminals on the main power supply of the unit, inside the regulator box. - After switching on, is undersized the unit switches off Performance circuit breaker The performance circuit breaker is undersized Short circuit accrued on the electroinstillation Check if correct type and size of the circuit breaker is used as per data on the manufacturer label of the unit. Check all the electrical connection in the unit regulator, engines,heater, connecting cable and connected external components for possible occurrence of short circuit. - Metal sounds coming out of the unit The rotor of the ventilator is loos or the engine bearings are damaged Check if the ventilators rotate freely. If not, replace the damaged ventilator - Smell is coming out of the unit The dust collected on the electrical heater is burning This happens when launching winter operation. If the filters areregularly cleaned, the impurities are not significant and the smell will soon disappear. If you will not be able to discover the fault or if the fault requires interference with the unit, contact an authorized service centre! 13

6 5. SERVICE 6. ACCESSORIES 5.1 WHEN YOU ARE UNABLE TO REPAIR THE FAULT In the event that you did not manage to solve the problem, contact the supplier or an exclusive distributor of the company 2VV. The warranty and after warranty service will be carried out by an authorized service organisation included on the list available; the 2VV company has exclusive distribution. To ensure the fast repair of the fault, please provide the following information: Product type Serial number Running period Accessories used, Place of installation, Conditions for installation (including electrical), Detailed description of the fault and the steps taken to repair the fault. 5.2 DISCARDING THE PRODUCT FROM OPERATION LIQUIDATION Prior to liquidation of the product, make it unusable. Even old products contain materials which can be recycled. Take those materials to a waste recycling centre. It is better to have the product liquidated in a specialised place where there is a guarantee that the materials will be recycled. Take the unusable parts of the product to the organised waste centre. It is necessary to follow the relevant national regulations concerning waste liquidation. Original accessories suitable for connecting to the ISIS Recover: KABEL HL136N + HL DM-SET-05-5 data cable siphon + connection pipe pressostat Further information is listed in the 2VV product catalog or on the website 7. FINALLY To ensure the correct use of the unit, it is necessary to read the instruction manual for the safe operation of the ventilation unit. In the event of any queries or questions, do not hesitate to contact our sales department or our technical support department. CONTACT Address 2VV, s.r.o., Poděbradská 289, Pardubice, Czech Republic Internet 14