33 URAI DSL Roots. Quick Specs. Also Available in: Part Number T

Transcription

1 33 URAI DSL Part Number T Detachable steel mounting feet Rigid one piece cast iron casing Connections in standard pipe sizes Straight, precision machined two lobe impellers Splash oil lubricated gear and drive ends Carburized and ground alloy steel spur timing gears Anti Friction gears Ground steel shafts Center Timed for rotation in either direction Also Available in: URAI URAI J (Whispair) URAI G (Gas) URAI J DSL URAI Metric Equivalent to: Sutorbilt Model 3MP Tuthill Model 3003* *Model size 3003 is supplied with 7/8 diameter drive shaft. When replacing with a Roots model you will need to adjust your drive components to accommodate the 3/4 drive shaft of the Roots blower Quick Specs Distributor Packager Repair Center Roots Flow Range to 95 CFM Max Pressure PSI Max Vacuum 5" Hg Maximum RPM 3600 Minimum RPM 090 Max T 5 F Connection Size " FPT Shaft Dia. 0.75" Min Sheave Dia. 5 Drive End Lubrication Oil Gear End Lubrication Oil Oil Sump Gear End Horiz Config ~0.5 oz Oil Sump Gear End Vert Config ~8.5 oz Oil Sump Drive End Horiz Config ~6.5 oz Oil Sump Drive End Vert Config ~4 oz Bare Unit Weight 77 lbs Shipping Weight 8 lbs Shipping Container Box Box Size (L x W x H) 7" x 6" x Can Ship via UPS Insured

2 Universal RAI-DSL Series Blowers Parts List 3-/" 5" Gear Diameter (Refer to drawing #T ) Item # Part Name Qty. Headplate Gear End Headplate Drive End 3 Gearbox 4 Timing Gears 7 Gasket, Gear Box, DE Cover 3 Cylinder Impeller & Shaft Drive 4 3 Impeller & Shaft Driven 4 Bearing, Ball 5 Bearing, Roller 3 6 Pin, Dowel 6 7 Gear Nut 9 Key * Plug, Pipe 4 3 Screw Hex 4 5 Breather (Plug Vent) 6 6 Screw, Hex 7 Seal, Lip Bearing 3 Screw, Hex, Nylock 3 Screw, Hex 4 33 Seal Lip-Drive 34 Clamp Plate 35 Foot 39 Washer Mounting 40 Screw Socket 4 Screw Hex 48 DE Oil Slinger Set Screw 4 50 Drive End Cover 5 Drive End Oil Slinger 53 Oil Sight Glass *Quantities vary by blower. 30 Table - Recommended Oil Grades 0 Ambient* Temperature F ( C) Above 90 (3 ) 3 to 90 (0 to 3 ) 0 to 3 (-8 to 0 ) Below 0 (-8 ) *Ambient temperature is defined as the temperature blower and drive are located. ISO Viscosity No of the space in which the Due to sludge build-up and seal leakage problems, Roots recommendation is DO NOT USE Mobil SHC synthetic oils in ROOTS blowers. Repair Kits Repair kits are bundled with the parts you need to complete a standard repair. It is more cost effective to buy a repair kit than to purchase individual parts. However, if you need parts not listed in the kit, it is recommended that you call Pathfinder Systems for parts pricing. P/N 65050RK Kit without Gears for 3, 33, 36 URAI, URAI-DSL, URAI-J, URAI-J-DSL, URAI-Metric, URAI-DSL-Metric Item Qty 3 Kit Description P/N 5 PLUG,OPENING FOR GSKT,GRBX 3-/ URAI TS BRG,BALL BRG,ROLLER NUT,HEX ESNA 5/ SEAL,LIP(VITON) 3/6 SF SCR,CAP HEXH NYL /4-0X SEAL,LIP for GREASE LUBE A SEAL,LIP for DSL T00800 P/N 65040RK Kit with Gears for 3, 33, 36 URAI, URAI-DSL, URAI-J, URAI-J-DSL, URAI-Metric, URAI-DSL-Metric Item Qty 3 Kit Description P/N 4 GEAR,ASSY 3-/ URAI T/ PLUG,OPENING FOR GSKT,GRBX 3-/ URAI TS BRG,BALL BRG,ROLLER NUT,HEX ESNA 5/ SEAL,LIP(VITON) 3/6 SF SCR,CAP HEXH NYL /4-0X SEAL,LIP for GREASE LUBE A SEAL,LIP for DSL T00800 ROOTS Synthetic Oil: ISO-VG-30 Grade Part Number Quart Gallon Case ( qts) ROOTS Synthetic Oil: ISO-VG-0 Grade Part Number Quart Gallon Case ( qts) ROOTS Synthetic Oil: ISO-VG-50 Grade Part Number Quart Gallon 3060 Case ( qts) Gallon Pail Gallon Drum ROOTS Synthetic Oil: ISO-VG-00 Grade Part Number Quart 3060 Gallon 3060 Case ( qts) Gallon Pail Gallon Drum 30606

3 Assembly of UNIVERSAL RAI Series - DSL with Splash Lubricated Drive End 3-5" Gear Diameter

4

5 S PECIFICATIONS ROOTS TM UNIVERSAL RAI DSL DUAL SPLASH LUBRICATED ROTARY POSITIVE BLOWERS Frames 3 thru 65 BASIC BLOWER DESCRIPTION Universal RAI DSL (Dual Splash Lubricated) blowers are heavy-duty rotary blowers designed with detachable, rugged steel mounting feet that permit easy, in-field adaptability to vertical or horizontal installation requirements. Because of the detachable mounting feet, these units can be easily adapted to any of four drive shaft positions: right, left, bottom, or top. The compact, sturdy design is engineered for continuous service when operated in accordance with speed and pressure ratings. This model consists of a cast iron casing, carburized and ground alloy steel spur timing gears secured to steel shafts with a taper mounting and locknut, and cast iron involute impellers. Oversized antifriction bearings are used, with a cylindrical roller bearing at the drive shaft to withstand V-belt pull. The Universal RAI DSL blower features splash oil lubrication on both the gear end AND drive end. ROOTS exclusive figure-eight gearbox design improves oil distribution to maximize gear and bearing life. Sight glasses (3/8 ) are provided for accurate oil level confirmation. After testing, the unit is sprayed with a protective paint, and boxed or skid mounted for delivery. Available accessories include driver, relief valve, inlet and discharge silencers, inlet filter, check valve, extended base, V-belt or flexible coupling and drive guards. OPERATING PRINCIPLE OUTLINE DRAWING & DIMENSIONAL TABLE INLET & DISCHARGE CONNECTIONS O R C B M U - 00 TOP SHAFT BOTTOM SHAFT D D LEFT DISCHARGE VERTICLE CONFIGURATION P A TOP DISCHARGE P AX AX D A BOTTOM DISCHARGE RIGHT DISCHARGE HORIZONTAL CONFIGURATION O' Two figure-eight lobe impellers mounted on parallel shafts rotate in opposite directions. As each impeller passes the blower inlet, it traps a definite volume of air and carries it around the case to the blower outlet, where the air is discharged. With constant speed operation, the displaced volume is essentially the same regardless of pressure or temperature. Timing gears control the impellers relative positions and maintain small but definite clearances. This allows operation without lubrication requirements inside the unit casing. INLET Frame A A B C D D D M O O P P R U DISCH. AX WGT NPT NPT NPT NPT NPT NPT NPT NPT NPT NPT NPT FLG S-7S03 September 003

6 Copyright 003 Dresser, Inc. All rights reserved. Dresser Design and Universal RAI DSL are registered trademarks of Dresser, Inc. ROOTS TM is a trademark of Dresser, Inc. All information subject to change without notice. website: ROOTS@dresser.com S-7S03 September 003 Dresser ROOTS 35 Hwy 6 South Houston, TX Ph: Fx: Toll Free (US): ROOT(S) Dresser ROOTS Connersville 900 West Mount Street Connersville, IN 4733 Ph: Fx: Dresser ROOTS Holmes Operation PO Box B7 Off St. Andrews Rd Turnbridge, Huddersfield England HD 6RB Ph: Fx: PERFORMANCE TABLE: ROOTS Universal URAI-DSL Frame 4 PSI 5 PSI 6 PSI 7 PSI 8 PSI 9 PSI 0 PSI PSI 3 PSI 4 PSI 5 PSI VACUUM DATA Size Speed CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP CFM BHP INHGV CFM BHP NOTES:. Performance based on inlet air at standard pressure of 4.7 psia, standard temperature of 68º F, and specific gravity of.0.. Vacuum ratings based on inlet air at standard temperature of 68º F, discharge pressure of 30 Hg and specific gravity of.0. DESIGN AND CONSTRUCTION FEATURES. Detachable steel mounting feet 4. Splash oil lubricated spur timing gears 7. Straight, precision machined two. Rigid one-piece cast iron casing 5. Connections in standard pipe sizes precision machined two-lobe impellers 3. Anti-friction bearings 6. Ground steel shafts

7 PERFORMANCE BASED ON AIR, INLET FLOW - ACFM PRESSURE PERFORMANCE FRAME 33 U-RAI MAX. PRESSURE RISE = PSI MAX. SPEED = 3600 RPM INLET AT 4.7 PSIA & 68 0 F DECEMBER PSI 6 PSI 8 PSI 0 PSI PSI TEMP. RISE - F PSI 0 PSI 8 PSI 6 PSI 4 PSI BRAKE HORSEPOWER PSI 0 PSI 8 PSI 6 PSI 4 PSI SPEED - RPM PC--33

8 INLET FLOW - ACFM VACUUM PERFORMANCE FRAME 33 U-RAI MAX. VACUUM = 5" HG MAX. SPEED = 3600 RPM PERFORMANCE BASED ON AIR, INLET AT 68 0 F DISCHARGE PRESSURE = 30" HG ABS. DECEMBER 004 6" HG 0" HG " HG 5" HG TEMP. RISE - F " HG " HG 0" HG 6" HG BRAKE HORSEPOWER " HG " HG 0" HG 6" HG SPEED - RPM VC--33