MODEL PA. Chimney and Exhaust Systems. Underwriters c. Laboratories Inc. LISTED

Transcription

1 MODEL P Chimney and Exhaust Systems UL UL Underwriters c Laboratories Inc. LISTED

2 LISTINGS The Schebler Model P chimney and exhaust system is listed by Underwriters Laboratories Inc. (UL) under file number MH739 for use as a 00 F Chimney, a 00 F Building Heating ppliance Chimney for positive pressures to 0"WC and for Grease Duct. It also has the Underwriters Laboratories Mark for Canada (cul). The system is also approved by the New York City Department of Buildings for use in New York City. ME # 22794M. SYSTEM CONCEPT The Model P is a modular double wall prefabricated exhaust system with 1" air gap for use in venting appliances that require a positive, neutral or negative draft exhaust system. Sections are provided in lightweight, easytohandle lengths. Connections are sealed with pressure tight drawbands and high temperature sealant. Straight sections, expansion joints, tees, elbows and support devices are offered, allowing a complete exhaust system to be assembled from standard components. SURROUNDINGS The Model P Chimneys are suitable for use with Building Heating ppliances and other low heat appliances as described in the Chimney Selection chart of the National Fire Protection ssociation Standard Number 2 which produce flue exhaust gases not exceeding 00 F under continuous operation or 0 F intermittent operation. These chimneys are to be installed as required for metal chimneys. They are not to be enclosed within combustible construction. n unenclosed chimney may be placed adjacent to walls of combustible construction at the clearances specified. COMPLETE LINE OF FITTINGS ND SIZES VILBLE The Model P chimney system is available in even and odd diameters ranging from " to 4". complete line of Straight Sections, Expansion Joints, Tee's, Elbows, Rain Caps, Roof Penetration components and support members are offered. In addition to the standard components virtually any conceivable fitting is available as a special order item. MTERILS VILBLE The Model P is available in a variety of materials allowing the proper material selection for your specific application. The standard product features a 4 stainless steel liner and an aluminized steel outer shell. For greater corrosion resistance 3 stainless steel is available for the liner and 4 or 3 stainless steel for the outer shell. For most applications the standard 4SS inner, aluminized outer material selection is sufficient. Under the following conditions you may consider the use of alternate materials: Boilers firing oils heavier than #2 use 3SS for the inner shell. Exterior installations which are not easily accessible for periodic painting you should consider a 4SS outer shell which will require no maintenance. MTERIL THICKNESS The standard material thickness for liners is ga. (.03 ); for shells it is 22 ga. (.034 ). Fittings larger than diameter utilize 1 ga. (.04 ) on the shell. Pipe diameters larger than 3 utilize 1 ga. on the liners and the shells. TESTS PERFORMED The Model P has endured rigorous tests by Underwriters Laboratories. Just a few of the tests performed are: Structural Tests The support plates and wall supports have been physically tested to carry a load 4 times that allowed by our listing. Wind Load Tests Loads equivalent to 0 mph wind have been applied to the chimney with acceptable results. Skin Temperature Rise Tests The chimney has been subjected to a series of burn tests at temperatures up to 0 F. The purpose of these tests is to determine safe clearances from the chimney wall to combustible materials. Rain Tests The rain caps have been tested to ensure that an unsatisfactory amount of water does not enter the rain cap. UNIQUE FETURES The Model P offers some unique features that no other chimney manufacturer can provide. ll of our liners and shells are continuously seam welded. We do not use spot welds on any of our seams. This assures a leak proof joint and maximum strength. This also minimizes corrosion, adding longevity to the stack. Our pipe sections utilize a stiffening bead on the liners. This bead maintains concentricity of the pipe. We do not use captive nuts and bolts. If you have ever installed a system that uses these types of bolts you know how difficult it can be to align and get a nut started on a bolt. lso you do not scrap a band if a nut gets stripped or damaged. ll hardware can be easily located at your local hardware store in case of emergency. Our boiler adapters include a seal ring to cover the gap between the liner and shell. The seal ring will provide a neat and completed appearance as well as preventing rodents and birds from entering the area between the shells. Union made by members of Sheet Metal Workers International ssociation. SUPPORT LIMITS Support plates and Wall supports are utilized to support the weight of the chimney and to provide a fixed point to allow proper operation of expansion joints. In horizontal runs supports should be placed adjacent to fittings that are not otherwise supported. See the individual part description for allowable support charts. 2

3 OPERTING TEMPERTURES ND CLERNCES CHRT The model P has been tested and listed for continuous use at both 00 F and 00 F as well as for use as Grease Duct at the following clearances to combustible materials. The clearance shown is from the shell to combustibles. P Clearance to Combustibles Section Inside 00 F (0 C) 00 F (70 C) Grease Diameter Chimney* Chimney Duct " " (2mm) 7" (mm) " (2mm) " 7" (mm) " (3mm) " (3mm) " 7" (mm) " (3mm) " (3mm) " " (3mm) 9" (2mm) " (mm) 1 (3mm) 9" (2mm) " (mm) 1" 9" (2mm) " (mm) " (279mm) " 9" (2mm) " (mm) " (279mm) 22" " (mm) " (279mm) " (mm) " " (mm) " (279mm) " (mm) " " (279mm) " (mm) " (3mm) 2" " (279mm) " (mm) " (3mm) " " (mm) " (3mm) " (40mm) " " (mm) " (3mm) " (40mm) 34" " (3mm) " (3mm) 1" (47mm) 3" " (3mm) " (3mm) 1" (47mm) 3" " (3mm) " (31mm) 1" (47mm) 40" " (3mm) " (31mm) 1" (47mm) 42" " (31mm) " (40mm) 1" (47mm) 44" " (31mm) " (40mm) 1" (47mm) 4" 1" (47mm) " (1mm) 1" (47mm) 4" 1" (47mm) " (1mm) 1" (47mm) JOINT SSEMBLY 1. pply a continuous 1 4" bead of the proper sealant to one of the flanges being joined. 2. Fill the V in the inner band with the proper sealant. 3. Join the two flanged ends of the sections. 4. Install the inner band around the flanges and tighten the screws.. Place the outer band over the space between the shells of the adjoining sections and tighten the screws. NOTE: For outdoor installations, apply a bead of S00 sealant in the groove at the upper end of the outer band. SELNT Schebler offers three types of sealant, S00, S00, and S01. The S00 is used for applications with flue gas temperatures up to 00 F (3 C). This includes most boilers and water heaters. The S00 is used for grease duct systems. S01 is used for installations operating under positive pressure, such as generator exhaust. *Building Heating ppliance Chimney Clearance to noncombustible materials for all diameters and applications is 1" (2mm). PRT NUMBERS ll standard parts manufactured by Schebler are identified by a part number which describes their make up and function. The part numbers are made up as follows 1. The first series is the model designation, P, P1, P2, P2, P4, or SW. 2. This is followed by the part name. For example 47S, 90T, and CC. 3. Next is the part s internal diameter in inches, such as 0,,. 4. Last is the liner/shell material designation. CODE LINER/SHELL MTERIL 4/luminized B 3/luminized C 4/4 or all 4 D 3/4 E 3/3 or all 3 F Galvanized G luminized H Painted Carbon Steel For example the part number for an " ID, Model P, 47" long straight section with a 4 stainless steel liner and aluminized steel shell is: P47S0. STEP 1 STEP 2 STEP 3 STEP 4 STEP STEP 3

4 SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILBLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES DPTER KIT (FLNGED) Part No. BKF The dapter Kit Flanged is used for securing pipe to a flanged appliance outlet. Beam clamps are provided for connection of the flanges or the flange can be drilled in the field to match the appliance. 1 seal ring to cover the gap between the inner and outer shells. DPTER KIT (RW) Part No. BKR The dapter Kit Raw is used for securing pipe to an unflanged appliance outlet. 1 seal ring to cover the gap between the inner and outer shells. STRIGHT SECTION Part No. 1S, S, 47S, and 9S Standard lengths are as follows: Diameter " is 1", " and 47" Diameter "" is 1", ", 47" and 9 Diameter "4" is 1", " and 47" Custom parts can be manufactured to any length over ". Includes 1 inner and 1 outer band. DJUSTBLE LENGTH Part No. 1L, 22L, L, and 4L The djustable Length is used to provide adjustment during installation as well as compensate for thermal expansion between fixed points. The adjustment in length available for each part is as follows: 1L = " to " 22L = " to 21" L = " to " 4L = " to 44" Includes 1 inner and Part No. BKF CLMPS " 3 " 4 " " " 7 " 1" 9 " 22" " " 2" " " 34" 3" 1 3" 19 40" 42" 21 44" 22 4" 4" Part No. BKR " " " " " " 1" " 22" " 2" " " 34" 3" 3" 40" 42" 44" 4" 4" Part No. 1S/S/47S/9S 1" " " 22" " " " 2" 2" " " " Part No. 1L/22L/L/4L 1" " " 22" " " " 2" 2" " " " 4

5 VRIBLE LENGTH SECTION Part No. 1VS, VS, VS The Variable Section adjusts to provide a fixed odd length between 2 sections. The minimum length is ", the maximum is 1", ", or 40". This part does not provide for thermal expansion. Includes liner, shell, slip joint, and 1 inner band. Part No. 1VS/VS/VS 1" " " 22" " " " 2" 2" " " " BELLOWS SECTION Part No. BS The Bellows Section is offered as an option to the djustable Length. This part is recommended for diesel engine and turbine exhaust systems. Compensates for 3" of thermal expansion. Includes liner, shell, and 1 inner band. Part No. BS 1" " " 22" " " " 2" 2" " " " TPERED INCRESER Part No. TI The Tapered Increaser is used when a change in pipe diameter is required. Includes 1 inner and 1 outer band of both smaller and larger size. Part No. TI B B B B " " 1" " 21" " " " " 1" " 21" 1" " " 1" 21" " " " 1" 1" " 21" " " 1" 22" 21" " " 1" " " 22" 1" " 21" " " " 22" " " 1" " 21" 2" " " " 1" 2" 21" " " " " " 2" 1" " 21" " " " 2" " " 1" " 21" 34" " 2" " " " 1" 34" 21" 3" " " " " 34" 1" 3" 21" 3" " " 3" 1" 3" 21" 40" " " 3" 1" 40" 21" 42" " " 40" 1" 42" 21" 44" " " 42" 1" 44" 21" 4" " " 44" 1" 4" 21" 4" " " 4" 1" 4" 21" ~ ~ " 4" 1" ~ ~ ~ ~ " ~ ~ ~ ~ ~ ~ 4" ~ ~ ~ ~ ~ ~ ~ ~ *ny size diameter change is possible. **Call for height if not shown. BRUPT INCRESER Part No. I The brupt Increaser is used to connect 2 sections of different diameters in a shorter space than a Tapered Increaser. Includes 1 inner band of larger and smaller sizes and 1 seal ring.

6 SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILBLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES 90 TEE Part No. 90T The 90 Tee is used to join horizontal and vertical sections, as well as to provide for connection of drain or inspection fittings. Use either the Drain Tee Cap or the End Cap for closure of the unused opening. Includes 2 inner bands and 2 outer bands. Note: Grease Tees available 1 1 2" containment dam located at one opening. REDUCING 90 TEE Part No. R90T The Reducing 90 Tee is used to join horizontal and vertical sections of different sizes, as well as provide for connection to drain or inspection fittings. Use either the Drain Tee Cap or the End Cap for closure of the unused opening. Specify size of branch required. Includes 1 each inner band and outer band for larger and smaller opening. 4 LTERL TEE Part No. 4LT The 4 Lateral Tee is used for low flow resistance entry into a stack or breeching. Includes 2 inner bands and 2 outer bands. Note: Grease Tees available 1 1 2" containment dam located at one opening. REDUCING 4 LTERL TEE Part No. R4LT The Reducing 4 Lateral Tee is used for low flow resistance entry into a stack or breeching when the stack or breeching is a larger size. Specify size of branch required. Includes 1 each inner band and outer band for larger and smaller opening. Part No. 4LT Part No. 90T " 1 2" " 1 2" " 1 2" " 1 2" " 1 2" " 1 2" 1" 1 2" " 1 2" 22" 1 1 2" " " " 1 2" 2" " " " " 1 2" 34" 1 2" 3" 2 1 2" 3" 1 2" 40" " 42" 2 1 2" 44" 1 2" 4" 1 2" 4" 1 2" Part No. R90T " 1 2" " 1 2" " 1 2" " 1 2" " 1 2" " 1 2" 1" 1 2" " 1 2" 22" 1 1 2" " " " 1 2" 2" " " " " 1 2" 34" 1 2" 3" 2 1 2" 3" 1 2" 40" " 42" 2 1 2" 44" 1 2" 4" 1 2" 4" 1 2" B C " 7" " 19" " 7 3 " 2 3 4" 21 3 " " 7 3 4" 1 2" 3 4" " 1 4" " 1 4" " " " 2 " " 9 1 " 40 1 " 1 " 1" 9 1 2" 43" " " 9 7 " 4 3 4" 3 7 " 22" " 4 " 3 " " 3 4" 1 1 2" " " 1 " 4 1 4" 43 1 " 2" 9 " 7 1 " 4 9 " " " 0" 4" " 3 " 2 3 4" 0 3 " 34" 3 4" 1 2" 2 3 4" 3" 3 " 3 " 3 " 3" " " 7 " 40" " 74" 0" 42" 7 " 7 7 " 2 7 " 44" 7 " " 4 7 " 4" 1 4" 2 1 2" 7 1 4" 4" " 3 " 9 " Part No. R4LT B C " 7" " 19" " 7 3 " 2 3 4" 21 3 " " 7 3 4" 1 2" 3 4" " 1 4" " 1 4" " " " 2 " " 9 1 " 40 1 " 1 " 1" 9 1 2" 43" " " 9 7 " 4 3 4" 3 7 " 22" " 4 " 3 " " 3 4" 1 1 2" " " 1 " 4 1 4" 43 1 " 2" 9 " 7 1 " 4 9 " " " 0" 4" " 3 " 2 3 4" 0 3 " 34" 3 4" 1 2" 2 3 4" 3" 3 " 3 " 3 " 3" " " 7 " 40" " 74" 0" 42" 7 " 7 7 " 2 7 " 44" 7 " " 4 7 " 4" 1 4" 2 1 2" 7 1 4" 4" " 3 " 9 "

7 90 BOOT TEE Part No. BT The 90 Boot Tee is used to join horizontal and vertical sections with lower resistance as well as to provide for connection of drain or inspection fittings. Use either the Drain Tee Cap or the End Cap for closure of the unused opening. Includes 2 inner bands and 2 outer bands. 90 WYE Part No. 90Y The 90 Wye is used for joining runs where low flow resistance is desired. ll openings must be the same size. For connection to smaller diameter sections use the Tapered or brupt Increasers. Includes 2 inner bands and 2 outer bands. Note: Grease Wye available 1 1 2" containment dam located at one opening. END CP Part No. EC The End Cap is used to close an unused tee opening and to provide a means of accessing the interior of the system for inspection and cleaning. Includes 1 inner band. DRIN TEE CP Part No. DTC The Drain Tee Cap is used to close an unused tee opening and to provide a drain at the base of a vertical chimney. Includes 1 inner band. Part No. EC Part No. DTC Part No. BT " 1 2" " 1 2" " 1 2" " 1 2" " 1 2" " 1 2" 1" 1 2" " 1 2" 22" 1 1 2" " " " 1 2" 2" " " " " 1 2" 34" 1 2" 3" 2 1 2" 3" 1 2" 40" " 42" 2 1 2" 44" 1 2" 4" 1 2" 4" 1 2" Part No. 90Y B " 1 2" 7" " 1 2" 7 " " 1 2" 7 " " 1 2" 7 " " 1 2" " " 1 2" 9 1 " 1" 1 2" 9 7 " " 1 2" 9 7 " 22" 1 1 2" 9 " " " " " 1 2" 1 " 2" " " " " " " 1 2" 3 " 34" 1 2" 2 " 3" 2 1 2" 3 " 3" 1 2" " 40" " 1 " 42" 2 1 2" " 44" 1 2" 27 " 4" 1 2" 1 4" 4" 1 2" " 1" " " 22" " " " 2" 2" " " " 1" " " 22" " " " 2" 2" " " " 7

8 SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILBLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES 90 ELBOW Part No. 90L The 90 Elbow is used when making a 90 directional change. The 90 Elbow is available in sizes " through ". For a 90 directional change in diameters from " through 4" use two 4 Elbows. 4 ELBOW Part No. 4L The 4 Elbow is used when a vertical or horizontal direction change of 4 is desired. ELBOW Part No. L The Elbow is used when a vertical or horizontal direction change of is desired. Part No. 90L " 1 2" " 1 2" " 1 2" " " " " " 1 2" 1" 2 1 2" " " 22" 1 2" " 1 2" Part No. 4L ID B C D " 7" 9 " " " " 7 3 " 7 " 2 3 " " " 7 3 " 3 4" 43 4" 1 4" " 1 4" 43 4" 2 4" " " " 4" 4" 3 4" " 9 1 " 1 " " 21 7 " 1" 9 1 2" 7 " 7 " 22 " " 9 7 " " 33 " 27 " 22" " 37 4" 3 4" 7 4" " 3 4" 4" 3 4 4" 2 1 4" " 1 " 47 4" " 4" 2" 9 " 4" 39 4" " " " 7 " " 2 " " 3 " 1 2" " 7 " 34" 3 4" 1 1 " 43 " 2 " 3" 3 " 1 21 " 4 1 " 27 " 3" " 19 4" " 7 4" 40" " " " " 42" 7 " 27 4" 19 4" 34 4" 44" 7 " 21 1 " 0 2 " 3 4" 4" 1 4" 21 9 " 2 1 " 3 " 4" " 22 3 " 3 9 " 37 7 " Part No. L ID B C D " 1 " 1 " 22 4" 4" " 3 " 3 " 1 4" 47 34" " " " " 9 " " " " 2 7 4" 1 4" " 7 3 " 7 3 " 3 4" 4" " 7 7 " 7 7 " " 1 " 1" 7 3 4" 7 3 4" 2 9 4" 4 4" " " " 4" 4 22" 1 4" 1 4" 1 4" " " 1 2" 1 2" " 1 " " 3 4" 3 4" 21 " 1 4" 2" 9 1 " 9 1 " " 19 " " 9 " 9 " " 1 " " 9 9 " 9 9 " 3 " 39 4" 34" 9 7 " 9 7 " 3 4" 21 9 " 3" 1 " 1 " 37 2 " 21 " 3" 3 " 3 " 3 " 22 4" 40" " " " " 42" " " 40 " 9 " 44" 3 " 3 " " 7 4" 4" 1 2" 1 2" " 2 " 4" 3 4" 3 4" 43 4" 2 "

9 DRIN SECTION Part No. DS The Drain Section is used to drain rain water and condensation from within the stack. The NPT nipple should be connected to a suitable drain. HORIZONTL DRIN Part No. HD The Horizontal Drain is used to attach grease traps and drain pipes to grease duct. NOZZLE SECTION Part No. NS The Nozzle Section is used to attach plumbing equipment to grease ducts. BSE DRIN SECTION Part No. BD The Base Drain Section provides a bottom closure and drain attachment for base supported chimneys. Part No. DS Part No. HD Part No. NS Part No. BD 1" " " 22" " " " 2" 2" " " " 1" " " 22" " " " 2" 2" " " " 1" " " 22" " " " 2" 2" " " " 1" " " 22" " " " 2" 2" " " " 9

10 SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILBLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES FLSHING Part No. FL The Flashing is used in conjunction with the Rain Collar to seal roof penetrations. This part is designed for flat roofs. Custom Pitched Flashings are available upon request. RIN COLLR Part No. RC The Rain Collar is used in conjunction with the Flashing to seal roof penetrations. INSULTED THIMBLE Part No. IT The Insulated Thimble is used when penetrating a combustible wall or roof. This part is designed for flat roofs. Custom Pitched Thimbles are available upon request. RIN CP Part No. CC The Rain Cap is used at stack terminations to prevent water from entering the flue. drain should be used at the base of stacks to drain off water that may be blown into flue. 1 closure ring to seal outer shell joint. Part No. RC Part No. FL B " 1 " 1 " " " 2" " 19" 27" " 21" " " " " " 2" 33" 1" 27" 3" " " 37" 22" " 39" " 33" 41" " 3" 43" 2" 37" 4" " 39" 47" " 41" " 34" 43" 1" 3" 4" 3" 3" 47" " 40" " 7" 42" 1" 9" 44" 3" 1" 4" " 3" 4" 7" " " 3 " " 1 " " 1 " " 1 " " 1 " " 1 1 " 1" 1 " " 22 1 " 22" 1 " " 1 " " 2 1 " 2" 1 " " 1 " " 34 1 " 34" 3 1 " 3" 3 1 " 3" 40 1 " 40" 42 1 " 42" 44 1 " 44" 4 1 " 4" 4 1 " 4" 0 1 " Part No. IT " " " " " " " " " 1" " " 1" 22" " " 22" " " 2" " " 2" " " 34" " 3" 34" 3" 3" 40" 3" 42" 40" 44" 42" 4" 44" 4" 4" 0" 4" 2" Part No. CC B " " 4 1 2" " 22" " " " 7 1 2" " " 9" " 2" 1 2" " " " 1" " 1 2" " 34" " 22" 3" 1 2" " 3" 1" " 40" " 2" 42" 21" " 44" " " " " 34" 2" 2 1 2" 3" " 27" 3" " 2 1 2" 40" 1" " 42" 4" 1 2" 44" 7" 33" 4" 70" " 4" 72" 3"

11 TOP SECTION EXIT CONE FLIP TOP CP Part No. FTC FN DPTER Part No. TS Part No. EXC Part No. F The Top Section is used to protect the insulating space between the inner and outer shells when an open termination is required. drain should be used at the base of stacks to drain off water that enters the system. shell joint. The Exit Cone is used to increase the flue gas velocity exiting the stack. drain should be used at the base of stacks to remove any water that enters the stack. 1 closure ring to seal outer shell joint. The Flip Top Cap is used in generator systems when the cap remains closed until pressure opens the cap. 1 closure ring to seal outer shell joint. The Fan dapter is used to attach grease duct to an exhaust fan or kitchen hood. Note: Plenum boxes available for multiple fan systems. Part No. TS 1" " " 22" " " " 2" 2" " " " Part No. EXC B " 4 7 " 3 " " 1 2" 1 " " 1 " 3 4" " 9 3 4" 7 1 2" " 3 " 1 " " 1 " 7 " 1" 3 4" 9 1 2" " 3 " 1 4" 22" 1" 7 " " 19 " " " " 1 4" 2" 22 7 " " " 1 2" " " 1 " 3 " 34" " " 3" 3 " 3 4" 3" " 3 " 40" " 1 " 42" " 3 4" 44" 3 7 " 1 1 2" 4" " 19 1 " 4" " " Part No. FTC 1" " " 22" " " " 2" 2" " " " Part No. F 1" " " 22" " " " 2" 2" " " "

12 SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILBLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES HORIZONTL TERMINTION Part No. HT The Horizontal Termination is used when the stack terminates in a horizontal position. Birdscreen covers the opening to prevent any birds or rodents from entering. SUPPORT PLTE Part No. SP The Support Plate is the primary load carrying member of the chimney assembly. This part is designed to support (B) (See Chart below) feet of vertical chimney section as well as provide fixed points in breeching runs. 2 half bands. NOTE: THIS PRT MUST BE PLCED T THE CONNECTION OF TWO FLUE SECTIONS. WLL SUPPORT Part No. WS The Wall Support is used to provide chimney support along a wall. The Wall Support will maintain the required clearance to combustible structures when properly installed and can support (C) (See Chart Below) feet of vertical chimney. 2 half bands. NOTE: THIS PRT MUST BE PLCED T THE CONNECTION OF TWO FLUE SECTIONS. GUY SECTION Part No. GS The Guy Section is to be used when the chimney extends beyond the vertical limits above the roof line. The Guy Section should be connected to guy wires or a rigid guying structure. 2 half bands. NOTE: THIS PRT MUST BE PLCED T THE CONNECTION OF TWO FLUE SECTIONS. Part No. HT " 19 9 " " 7 " " " " " " 1 2" " 1 2" 1" 2 1 2" " 1 2" 22" " " 2 1 2" Part No. SP B(FT.) " 19 3 " ' " 21 3 " 9' " 3 " 2' " 2 3 " 7' " 27 3 " 227' " 3 " 2' 1" 3 " 1' " 34 3 " 192' 22" 3 3 " ' " 3 3 " 2' " 40 3 " 1' 2" 42 3 " 1' " 44 3 " 2' " 4 3 " 1' 34" 4 3 " 1' 3" 0 3 " 3' 3" 2 3 " 1' 40" 4 3 " 93' 42" 3 " ' 44" 3 " 7' 4" 0 3 " ' 4" 2 3 " 0' Part No. WS B C(FT.) " " 3 " 193' " " 3 " 1' " " 3 4" 4' " " 1 " 3' " " 19 1 " ' 7 " 0' 1" " " 4' " 21" 1 " 9' 22" " 3 " 3' " " " 9' " " 1 2" 3' 2" 27" 7 " ' " " 7 " 3' " " " 1' 34" " 3 1 4" 4' 3" 33" 37 " ' 3" 3" 39 9 " 1' 40" 3" 40 " 77' 42" 3" 42 " 73' 44" 39" 44 " ' 4" 44" 47" 4' 4" 4" " 0' Part No. GS B " " " " " 3 " " 3 " " 19 3 " " 21 3 " 1" 3 " " 2 3 " 22" 27 3 " " 3 " " 3 " 2" 34 3 " " 3 3 " " 3 3 " 34" 40 3 " 3" 42 3 " 3" 44 3 " 40" 4 3 " 42" 4 3 " 44" 0 3 " 4" 2 3 " 4" 4 3 " 2

13 FULL RING Part No. FR HLF RING Part No. HR FLOOR/ROOF GUIDE WLL GUIDE Part No. WG Part No. FRG The Full Ring is used to guide horizontal and vertical runs. The part is simply bolted around the outer shell then rigidly connected to the building structure. The Half Ring has the same dimensions as the full ring. This Half Ring is used to support long horizontal runs. This part would be placed under the flue and then supported by rods connecting to the building structure. The Floor/Roof Guide is used at the penetration of floors and roofs to guide the chimney. This part is designed to absorb lateral loads only. It will not support vertical chimney sections. The Wall Guide is used to guide long vertical runs that are placed adjacent to walls. This part will maintain proper clearance to combustibles when properly installed. Part No. FR FLUE ID RING ID NGLE SIZE # HOLES HOLE SIZE B.C. " 1 " 1 1 4"x1 1 4"x 1 " 3 " 9 1 2" " 1 " 1 1 4"x1 1 4"x 1 " 3 " 1 2" " 3 " 1 1 2"x1 1 2"x 1 " 7 " " " 3 " 1 1 2"x1 1 2"x 1 " 7 " " " 3 " 1 1 2"x1 1 2"x 3 " 7 " 1 1 " " 1 3 " 1 1 2"x1 1 2"x 3 " 7 " 1 " 1" 3 " 1 1 2"x1 1 2"x 3 " 7 " 22 1 " " 22 3 " 1 1 2"x1 1 2"x 3 " 7 " 1 " 22" 3 " 1 1 2"x1 1 2"x 3 " 7 " 1 " " 3 " 2"x2"x 3 " 7 " 2 1 2" " 2 3 " 2"x2"x 3 " 7 " 1 2" 2" 3 " 2"x2"x 3 " 2 7 " 1 2" " 3 " 2"x2"x 3 " 2 7 " " " 34 3 " 2"x2"x 3 " 7 " 3 1 2" 34" 3 3 " 2"x2"x 3 " 7 " 3 1 2" 3" 3 3 " 2"x2"x 3 " 3 7 " " 3" 40 3 " 2"x2"x 3 " 3 7 " " 40" 42 3 " 2"x2"x 3 " 40 7 " " 42" 44 3 " 2"x2"x 3 " 40 7 " 4 1 2" 44" 4 3 " 2"x2"x 3 " 44 7 " 4 1 2" 4" 4 3 " 2"x2"x 3 " 44 7 " 0 1 2" 4" 0 3 " 2"x2"x 3 " 4 7 " 2 1 2" Part No. FRG " 9 3 " " 3 " " 3 " " 3 " " 3 " " 3 " 1" 3 " " 3 " 22" 3 " " 1 3 " " 19 3 " 2" 3 " " 21 3 " " 22 3 " 34" 3 " 3" 3 " 3" 2 3 " 40" 3 " 42" 27 3 " 44" 2 3 " 4" 3 " 4" 3 " Part No. WG B " " 7 " " " 1 2" " " " " " 9" " " 9 7 " 9 3 4" 1" " 1 4" " 21" 9 " 22" " 1 " " " " " " 7 " 2" 27" 1 " " " " " " " 34" " 1 2" 3" 33" " 3" 3" " 40" 3" 1 2" 42" 3" 1 " 44" 39" " 4" 44" " 4" 4" 7 "

14 SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILBLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES PRESSURE RELIEF VLVE Part No. PRV The Pressure Relief Valve is used in generator exhaust systems to prevent damage resulting in the ignition of unburned fuel. This component complies with NFP 37. SQURETOR0UND TRNSITIONS The SquaretoRound Transitions are used when connecting to appliances with square or rectangular outlets. The base can be raw for field welding or flanged for field drilling and bolting. Valves are set to 1 PSI. Part No. PRV " 9 1 " " " " " " " " " " 19" 1" 21" " " 22" 2" OUTER SHELL TEMP CHRT 700 F COLDFCE TEMPERTURE 00 F 00 F 400 F 0 F 0 F 0 F 0 F 30 F 00 F 00 F 00 F MIDFLUE TEMPERTURE

15 P WEIGHT CHRT Part Part Description Number " " to " djustable 1L lbs. " to 21" djustable 22L lbs. " to " djustable L lbs " to 44" djustable 4L lbs. " Straight Section S lbs. Degree Elbow L lbs. 4 Degree Elbow 4L 9lbs. 4 Degree Tee 4LT 1lbs. 47" Straight Section 47S lbs. 9" Straight Section 9S 90 Degree Elbow 90L lbs. 90 Degree Grease Tee 90GT lbs. 90 Degree Tee 90T lbs. brupt Increaser I 7lbs. Base Drain BD lbs. Bellows Section BS lbs. Boiler Kit Flanged BKF 7lbs. Boiler Kits Raw BKR 4lbs. Drain Section DS lbs. Drain Tee Cap DTC lbs. End Cap EC 4lbs. Fan dapter F 7lbs. Flashing FL lbs. Floor/Roof Guide FRG lbs. Full Ring FR 3lbs. Guy Section GS 9lbs. Half Ring HR 2lbs. Horizontal Drain HD lbs. Insulated Thimble IT lbs. Nozzle Section NS lbs. Rain Cap CC 9lbs. Rain Collar RC 4lbs. Support Plate SP lbs. Tapered Increaser TI lbs. Top Section TS 3lbs. Variable Section VS lbs. Wall Guide WG lbs. Wall Support WS 1lbs. " " " " " " " " Inside Diameter (Inches) " " 2" " " ll weights shown above are actual weights, for shipping weights multiply by " " " " " " " " SMPLE SPECIFICTION MODEL P The factory built modular chimney shall be laboratory tested and listed in accordance with Underwriters Laboratories Standard UL 3 for use with building heating equipment burning gas, solid or liquid fuels with flue gases not exceeding 00 F continuous operations and 0 F intermittent operation. It shall also be tested and listed for use as a Grease Duct in accordance with UL 197. Sections shall bear the UL listing mark and the cul listing mark for Canada. Sections shall be sealed with banded flanges and silicone joint sealant for temperatures up to 00 F and Grease Duct. Inner shell material shall be type 4 stainless steel for natural gas and number 2 oil fired appliances, type 3 stainless steel for coal, number 4 and number oil fired appliances. Inner shell thickness shall be.03" for " to 3" diameter systems and.04" for 3" to 4" diameter systems. ll inner shell seams shall be full penetration welded the entire length of the pipe section. Riveted, tack or spot welded seams are not permitted. Outer shell material shall be aluminized steel with a thickness of.034" for " to 3" diameter systems and.02" for 3" to 4" systems. (Outer shell thickness of optional type 4 or 3 stainless steel shall be.0" for " to 3" diameter systems and.04" for 3" to 4" diameter systems). ll outer shell seams shall be full penetration welded the entire length of the pipe section. Riveted, tack or spot welded seams are not permitted. Between the inner and outer shells there shall be a minimum of a 1" air gap. Stainless steel centering clips shall be welded to the outer shell to maintain the 1" spacing and ensure concentricity of the shells. Breeching and chimney sections, when installed according to manufacturers instructions, shall comply with national safely standards and building codes. Stacks terminating above a roof must terminate as required by code or NFP 2. Chimney sections exposed to atmospheric conditions shall be protected by a minimum of one base coat and one finish coat of heat resistant paint after installation. Outer shells of type 4 or 3 stainless steel need not be painted.

16 1 2 MODEL P STNDRD 1YER WRRNTY The Schebler Model P Chimney, where installed according to manufacturer s installation instructions, is warranted by the Schebler Company for a period of one (1) year from date of system startup, against defects in material and workmanship of the product for parts only. ny defective part in the product will, at Schebler s option, either be repaired or replaced. Should the part be returned, the owner must pay all transportation charges. The repaired or replacement part will, in turn, be shipped by Schebler to the owner, freight prepaid. The warranty on any repaired or replacement part shall be for a duration of time no longer than the remaining or unexpired term of the original warranty. This warranty does not cover labor or other service charges incurred by the owner, nor any parts not manufactured by The Schebler Company, or any other components that are not part of the Model P Chimney Systems. This limited warranty is extended to the purchaser subject to the satisfaction of the following conditions: Generally accepted engineering practices have been followed to determine that sizing and material specifications are suitable for the application and environment involved. The undamaged components have been correctly installed in accordance with the installation instructions published by The Schebler Company at the time of shipment. The Schebler Company assumes no liability for incidental or consequential damages of any kind or for any damages resulting in whole or part from misuse, improper installation, or inadequate maintenance of the system or component part thereof. This warranty is in lieu of all other express warranties or guarantees of any kind. ll implied warranties, including merchantability and fitness, are limited to the duration of the express warranty contained herein. The Schebler Company neither assumes nor does it authorize any other person to assume on its behalf any other liability in connection with the sale of its products. Inner shell 1/2 rolled flange Outer shell Inner shell Inner Vband with clips Outer band with clips 1 air gap Model P spacer clip MODEL P EXTENDED YER WRRNTY The Schebler Company warrants owners of its Model P Chimney against defects in material and workmanship in normal use for ten () years from the date of delivery to the construction site when installed, maintained and used as part of a Schebler Model P Chimney System and in accordance with The Schebler Company specifications. The Schebler Company further warrants any portion of the chimney system repaired or replaced under this warranty for the remainder of the original warranty period. This warranty is limited to repair or replacement of the product plus shipping cost to the failure location. This warranty does not cover any labor costs for removal or replacement of the defective product nor does this warranty cover any system components not furnished by The Schebler Company and installed as part of the system. This limited warranty is extended to the purchaser subject to the satisfaction of the following conditions: System sizing and design has been performed by Schebler personnel and design parameters provided to The Schebler Company by the responsible engineer were and are accurately representative of the operating conditions. The undamaged components have been correctly installed in accordance with system design and sizing as performed by Schebler and installation instructions published by The Schebler Company at the time of shipment. Proper precautions have been taken to insure that appliance air is free of solvent or refrigerant vapors or any halogenated compound which may cause acid condensate to form within the chimney. The Schebler Company has supplied the entire chimney or exhaust system from the appliance outlet to the termination of the stack. Prior to startup and thereafter, exposed aluminized steel surfaces are protected with a minimum of one base coat of primer and one finish coat of heat resistant paint at all times. The Schebler Company assumes no liability for incidental or consequential damages of any kind or for any damages resulting in whole or part from misuse, improper installation, or inadequate maintenance of the system or component part thereof. This warranty is in lieu of all other express warranties or guarantees of any kind. ll implied warranties, including merchantability and fitness, are limited to the duration of the express warranty contained herein. The Schebler Company neither assumes nor does it authorize any other person to assume on its behalf any other liability in connection with the sale of its products. Hwy. 7 & Fenno Road P.O. Box 0 Bettendorf, Iowa 2722 Phone (3) 3900 Fax (3) 394