ARMTRAC 20T MK2. A r m t r a c 2 0 T M K 2 M a i n U n i t. Armtrac Limited. Specification Sheets

Transcription

1 ARMTRAC 20T MK2 Specification Sheets Page 1 of 8

2 Machine Features 1. 74hp (55.4kW) 4 cylinder Kohler engine 5. Self-tightening tracks 9. Independent cooling for hydraulics 2. Ignition panel with warning system 6. High capacity water radiator 10. Double acting ram (attachment height) litre fuel tank capacity 7. Self-cleaning reversible fan 11. Quick access for servicing 4. Tracks hydraulically driven litre hydraulic oil reservoir 12. Master Switch Page 2 of 8

3 3870mm 3210mm 2460mm Page 3 of 8

4 1601mm 1900mm BACK VIEW 1370mm FRONT VIEW mm Page 4 of 8

5 Remote Features 1. 1 km working range with built-in antenna 8. Rotor start/stop 16. Engine Step 2. Radio frequency CE certified 9. Soft-start rotor engagement & 17. Cruise Control 3. Proportional joystick drive controls 10. Engine RPM control 18. Aux 2 4. Proportional joystick utility controls 11. Engine start with safety warning hooter 19. Aux 1 5. Steering bias (Trim) for working on slopes 12. Battery & remote link status indicators 20. Aux 3 6. Emergency stop (instant mechanical + electrical safety isolation) 13. LCD display indications of critical machine systems (oil press, etc.) 7. Two (2) speed control High / Low range 14. Engine Step Power on/off 15. Aux 4 Raise and Lower Rear Lift Arms/Winch In/Winch Out Page 5 of 8

6 Remote Features cont. Video Display System GHz HD LCD Screen Diversity Receiver 22 Receiver Antenna #1. (Omni-directional clover) 23 Receiver Antenna ~1. (High gain directional) Page 6 of 8

7 ENGINE Make KDI 45042TCR Turbo common rail, 4 cylinder HP 74 hp 1500 RPM (Maximum) Torque 300 Nm Fuel Diesel Fuel Tank Capacity 100 litres Fuel consumption (maximum) 16 litres per hour at max power Dependent on workload Water cooled Radiator Self-cleaning (Reversible fan) Transmission Hydrostatic Noise Levels 80 dbs Acoustic power level = db (A) LWA HYDRAULICS Independent flail/tiller head circuit Closed circuit piston hydraulic system 120 litres per minute RPM 300bar Independent track drive circuit 2 X closed circuit hydraulic piston pumps 52 Litres per minute 300bar Auxiliary service 1 double acting auxiliary service 9 litres per minute 210 bar Independent intercooler Oil tank capacity 80 litres Hydraulic 68 Attachment lifting capability 600kg HEADER (Flail/Tiller) Oil flow 120 litres per minute Pressure 300 BAR Rotor speed 600 to 800 RPM Picks 42 picks Header width 1986mm Flail diameter 800mm Cutting height range (vegetation cutting) 1.5 meters depending on conditions Hydraulic lift 2000mm Floatation (Angle) 14 up & down (+/-) Cutting / digging width 1566mm Digging tiller depth 200mm Max. TRACKS Rubber Working range up to 45 degrees Self-tightening Length (Axle to axle) Gear 1 Max Speed Gear 2 Max Speed 1429mm 5km/h 8km/h Page 7 of 8

8 REMOTE CONTROL Working range Frequency Battery Proportional joysticks WEIGHTS Armtrac 20T (Base unit) Tiller Flail Remote handset (Including battery) 1000 meters 2.4Ghz 3.6 Volt, 2.0 Ah, Ni-MH, rechargeable 2230 kg 374 kg 342 Kg 500 grams Page 8 of 8