Web/SNMP Management Card Event Support Chart

Transcription

1 Web/SNMP Management Card Event Support Chart 0x0001 System: Coldstart. 0x0002 System: Warmstart. 0x0003 System: SNMP configuration change. System: Detected an unauthorized user attempting to access the SNMP 0x0004 interface. 0x0005 System: Detected an unauthorized user attempting to access the Control Console interface. 0x0006 System: Detected an unauthorized user attempting to access the Web interface. 0x0008 System: Password changed. 0x000C System: File transfer started. 0x000D System: File transfer started. 0x000F System: File transfer failed. 0x0014 System: Control Console User logged in. 0x0015 System: Web User logged in. 0x0016 System: FTP User logged in. 0x0018 System: Reset to Defaults. 0x0019 System: Initializing data. 0x0101 UPS: Communications established. 0x0102 UPS: Communications lost. 0x0103 UPS: Sensed a load greater than 100 percent of rated capacity. 0x0104 UPS: Overload condition cleared. 0x0105 UPS: Passed internal self-test. 0x0106 UPS: Failed internal diagnostic self-test. 0x0107 UPS: Batteries discharged. 0x0108 UPS: Battery discharge condition cleared. 0x0109 UPS: Switched to battery backup power; utility power failure. 0x010A UPS: Returned from battery backup power; utility power restored. 0x010B UPS: Enabled SmartBoost; low incoming line voltage. 0x010C UPS: Returned from SmartBoost. 0x010D UPS: Enabled SmartTrim; high incoming line voltage. 0x010E UPS: Returned from SmartTrim. 0x010F UPS: Battery power is low and will soon be exhausted. 0x0110 UPS: Returned from a Low-Battery condition. 0x0113 UPS: Turned on. 0x0114 UPS: Turned off. 0x0115 UPS: Entered sleep mode. 3 0x0116 UPS: Returned from sleep mode. 3 0x0117 UPS: Started reboot sequence. 0x0119 UPS: Batteries need immediate replacement. 0x011A UPS: Bad battery condition cleared. 0x011B UPS: In bypass due to an internal fault. 0x011C UPS: In bypass due to user command via software or panel. 0x011D UPS: In bypass initiated by user. 0x011E UPS: Returned from bypass. 0x011F UPS: Base module bypass power supply failure. 0x0120 UPS: Base module fan failure. 0x0121 UPS: External battery pack communications established. 0x0122 UPS: External battery pack communications lost. 0x0123 UPS: Battery calibration test initiated. 1

2 0x0124 UPS: Battery calibration complete. 0x0125 UPS: Graceful shutdown initiated. 0x0126 UPS: SmartBoost or SmartTrim relay failure. 0x0127 UPS: SmartBoost or SmartTrim relay failure cleared. 0x0128 UPS: Bad output voltage condition. 0x0129 UPS: Bad output voltage condition cleared. 0x012A UPS: Battery charger failure. 0x012B UPS: Battery charger failure cleared. 0x012C UPS: Internal battery temperature threshold violation. 0x012D UPS: Internal battery temperature threshold violation cleared. 0x012F UPS: No batteries installed. 1 0x0130 UPS: No batteries installed cleared. 1 0x0201 UPS: Power Module failure. 0x0202 UPS: Power Module failure cleared. 0x0203 UPS: Intelligence Module failure. 0x0204 UPS: Intelligence Module failure cleared. 0x0205 UPS: Redundant Intelligence Module failure. 0x0206 UPS: Redundant Intelligence Module failure cleared. 0x0207 UPS: Battery failure. 0x0208 UPS: Battery failure cleared. 0x0209 UPS: Load(kVA) alarm threshold violation. 0x020A UPS: Load(kVA) alarm threshold violation cleared. 0x020B UPS: Redundancy lost. 0x020C UPS: Redundancy returned. 0x020D UPS: Redundancy below alarm threshold. 0x020E UPS: Redundancy below alarm threshold cleared. 0x020F UPS: bypass not in range; either frequency or voltage. 0x0210 UPS: bypass not in range cleared; either frequency or voltage. 0x0211 UPS: Bypass contactor stuck in bypass position. 0x0212 UPS: Bypass contactor stuck in bypass position cleared. 0x0213 UPS: Bypass contactor stuck in on-line position. 0x0214 UPS: Bypass contactor stuck in on-line position cleared. 0x0215 UPS: In bypass due to an internal fault. 0x0216 UPS: In bypass due to an internal fault cleared. 0x0217 UPS: In bypass due to an overload. 0x0218 UPS: In bypass due to an overload cleared. 0x0219 UPS: In maintenance bypass. 0x021A UPS: In maintenance bypass cleared. 0x021B UPS: Input circuit breaker tripped open. 0x021C UPS: Input circuit breaker tripped open cleared. 0x021D UPS: System level fan failure. 0x021E UPS: System level fan failure cleared. 0x021F UPS: Redundant Intelligence Module in control. 0x0220 UPS: Redundant Intelligence Module in control cleared. 0x0221 UPS: IIC inter-module communications failure. 0x0222 UPS: IIC inter-module communications failure cleared. 0x0223 UPS: No working Power Modules. 0x0224 UPS: No working Power Modules cleared. 0x0225 UPS: Load shutdown from bypass; input frequency or voltage outside limits. 2

3 UPS: Load shutdown from bypass cleared; input frequency or voltage outside 0x0226 limits. 0x0227 UPS: Runtime below alarm threshold. 0x0228 UPS: Runtime below alarm threshold cleared. 0x0229 UPS: Extended Run Frame fault. 0x022A UPS: Extended Run Frame fault cleared. 0x022B UPS: Output voltage out of range. 0x022C UPS: Output voltage out of range cleared. 0x022D UPS: Not synchronized fault. 0x022E UPS: Not synchronized fault cleared. 0x022F UPS: No batteries installed. 0x0230 UPS: No batteries installed cleared. 0x0231 UPS: Battery voltage high. 0x0232 UPS: Battery voltage high cleared. 0x0233 UPS: Non-specific fault; Access UPS keyboard for details. 4 0x0234 UPS: Non-specific fault cleared. 4 0x0235 UPS: Site wiring fault. 1 0x0236 UPS: Site wiring fault cleared. 1 0x0237 UPS: Backfeed protection relay open. 2 0x0238 UPS: Backfeed protection relay open cleared. 2 0x0239 0x023A 0x023B 0x023C 0x023D 0x023E 0x023F UPS: Bit 28 of the abnormal condition register set. UPS: Bit 28 of the abnormal condition register cleared. UPS: Bit 29 of the abnormal condition register set. UPS: Bit 29 of the abnormal condition register cleared. UPS: Bit 30 of the abnormal condition register set. UPS: Bit 30 of the abnormal condition register cleared. UPS: Bit 31 of the abnormal condition register set. 0x0240 UPS: Bit 31 of the abnormal condition register cleared. 0x0241 UPS: Number of batteries increased. 0x0242 UPS: Number of batteries decreased. 0x0243 UPS: Number of Power Modules increased. 0x0244 UPS: Number of Power Modules decreased. 0x0245 UPS: Intelligence Module inserted. 0x0246 UPS: Intelligence Module removed. 0x0247 UPS: Redundant Intelligence Module inserted. 0x0248 UPS: Redundant Intelligence Module removed. 0x0249 UPS: Number of Extended Run Frames increased. 0x024A UPS: Number of Extended Run Frames decreased. 0x024B UPS: Number of System Power Supplies increased. 0x024C UPS: Number of System Power Supplies decreased. 0x024D UPS: External Switch Gear Q001 closed. 0x024E UPS: External Switch Gear Q001 opened. 0x024F UPS: External Switch Gear Q002 closed. 0x0250 UPS: External Switch Gear Q002 opened. 0x0251 UPS: External Switch Gear Q003 closed. 0x0252 UPS: External Switch Gear Q003 opened. 0x0253 UPS: External Switch Gear Q004 closed. 0x0254 UPS: External Switch Gear Q004 opened. 0x0A01 UPS: Peak Current Limiter active. 0x0A02 UPS: Peak Current Limiter active cleared. 3

4 0x0A03 UPS: Bypass Power Supply fault. 0x0A04 UPS: Bypass Power Supply fault cleared. 0x0A05 UPS: Delta Current Limiter active. 0x0A06 UPS: Delta Current Limiter active cleared. 0x0A07 UPS: Fan fault. 0x0A08 UPS: Fan fault cleared. 0x0A09 UPS: High DC warning. 0x0A0A UPS: High DC warning cleared. 0x0A0B UPS: Inverter Voltage fault. 0x0A0C UPS: Inverter Voltage fault cleared. 0x0A0D UPS: Parallel Synchronization fault. 0x0A0E UPS: Parallel Synchronization fault cleared. 0x0A0F UPS: Second Power Supply fault. 0x0A10 UPS: Second Power Supply fault cleared. 0x0A11 UPS: Internal Power Supply fault. 0x0A12 UPS: Internal Power Supply fault cleared. 0x0A13 UPS: Bit 9 of the UPS specific fault register set. 0x0A14 0x0A15 0x0A16 0x0A17 0x0A18 0x0A19 0x0A1A UPS: Bit 9 of the UPS specific fault register cleared. UPS: Bit 10 of the UPS specific fault register set. UPS: Bit 10 of the UPS specific fault register cleared. UPS: Bit 11 of the UPS specific fault register set. UPS: Bit 11 of the UPS specific fault register cleared. UPS: Bit 12 of the UPS specific fault register set. UPS: Bit 12 of the UPS specific fault register cleared. 0x0A1B UPS: High Temperature Bypass Static Switch. 0x0A1C UPS: High Temperature Bypass Static Switch cleared. 0x0A1D UPS: High Battery Temperature. 0x0A1E UPS: High Battery Temperature cleared. 0x0A1F UPS: Battery Weak. 0x0A20 UPS: Battery Weak cleared. 0x0A21 UPS: Bit 16 of the UPS specific fault register set. 0x0A22 UPS: Bit 16 of the UPS specific fault register cleared. 0x0A23 UPS: System is locked in Operation Mode. 0x0A24 UPS: System is locked in Operation Mode cleared. 0x0A25 UPS: RAM1 Memory Write fault. 0x0A26 UPS: RAM1 Memory Write fault cleared. 0x0A27 UPS: Memory Write fault. 0x0A28 UPS: Memory Write fault cleared. 0x0A29 UPS: Communication to VQ Bypass lost. 0x0A2A UPS: Communication to VQ Bypass restored. 0x0A2B UPS: Communication to VQ Output lost. 0x0A2C UPS: Communication to VQ Output restored. 0x0A2D UPS: Communication to DMU lost. 0x0A2E UPS: Communication to DMU restored. 0x0A2F UPS: Communication to Controller lost. 0x0A30 UPS: Communication to Controller restored. 0x0A31 UPS: Communication to Parallel IF lost. 0x0A32 UPS: Communication to Parallel IF restored. 0x0A33 UPS: External Shutdown accepted. 0x0A34 UPS: External Shutdown accepted cleared. 4

5 0x0A35 UPS: DC Capacitor Charge fault. 0x0A36 UPS: DC Capacitor Charge fault cleared. 0x0A37 UPS: Communication to VQ Mains lost. 0x0A38 UPS: Communication to VQ Mains restored. 0x0A39 UPS: Bypass Synchronization fault. 0x0A3A UPS: Bypass Synchronization fault cleared. 0x0A3B UPS: Charge fault. 0x0A3C UPS: Charge fault cleared. 0x0A3D UPS: Bit 30 of the UPS specific fault register set. 0x0A3E 0x0A3F 0x0A40 0x0A41 0x0A42 0x0A43 0x0A44 0x0A45 0x0A46 0x0A47 0x0A48 0x0A49 0x0A4A 0x0A4B 0x0A4C 0x0A4D 0x0A4E 0x0A4F 0x0A50 0x0A51 0x0A52 0x0A53 0x0A54 0x0A55 0x0A56 0x0A57 0x0A58 0x0A59 0x0A5A 0x0A5B 0x0A5C 0x0A5D 0x0A5E 0x0A5F 0x0A60 0x0A61 0x0A62 0x0A63 0x0A64 0x0A65 0x0A66 UPS: Bit 30 of the UPS specific fault register cleared. UPS: Bit 31 of the UPS specific fault register set. UPS: Bit 31 of the UPS specific fault register cleared. UPS: Bit 32 of the UPS specific fault register set. UPS: Bit 32 of the UPS specific fault register cleared. UPS: Bit 33 of the UPS specific fault register set. UPS: Bit 33 of the UPS specific fault register cleared. UPS: Bit 34 of the UPS specific fault register set. UPS: Bit 34 of the UPS specific fault register cleared. UPS: Bit 35 of the UPS specific fault register set. UPS: Bit 35 of the UPS specific fault register cleared. UPS: Bit 36 of the UPS specific fault register set. UPS: Bit 36 of the UPS specific fault register cleared. UPS: Bit 37 of the UPS specific fault register set. UPS: Bit 37 of the UPS specific fault register cleared. UPS: Bit 38 of the UPS specific fault register set. UPS: Bit 38 of the UPS specific fault register cleared. UPS: Bit 39 of the UPS specific fault register set. UPS: Bit 39 of the UPS specific fault register cleared. UPS: Bit 40 of the UPS specific fault register set. UPS: Bit 40 of the UPS specific fault register cleared. UPS: Bit 41 of the UPS specific fault register set. UPS: Bit 41 of the UPS specific fault register cleared. UPS: Bit 42 of the UPS specific fault register set. UPS: Bit 42 of the UPS specific fault register cleared. UPS: Bit 43 of the UPS specific fault register set. UPS: Bit 43 of the UPS specific fault register cleared. UPS: Bit 44 of the UPS specific fault register set. UPS: Bit 44 of the UPS specific fault register cleared. UPS: Bit 45 of the UPS specific fault register set. UPS: Bit 45 of the UPS specific fault register cleared. UPS: Bit 46 of the UPS specific fault register set. UPS: Bit 46 of the UPS specific fault register cleared. UPS: Bit 47 of the UPS specific fault register set. UPS: Bit 47 of the UPS specific fault register cleared. UPS: Bit 48 of the UPS specific fault register set. UPS: Bit 48 of the UPS specific fault register cleared. UPS: Bit 49 of the UPS specific fault register set. UPS: Bit 49 of the UPS specific fault register cleared. UPS: Bit 50 of the UPS specific fault register set. UPS: Bit 50 of the UPS specific fault register cleared. 5

6 0x0A67 UPS: Bit 51 of the UPS specific fault register set. 0x0A68 UPS: Bit 51 of the UPS specific fault register cleared. 0x0A69 UPS: Bit 52 of the UPS specific fault register set. 0x0A6A UPS: Bit 52 of the UPS specific fault register cleared. 0x0A6B UPS: Bit 53 of the UPS specific fault register set. 0x0A6C UPS: Bit 53 of the UPS specific fault register cleared. 0x0A6D UPS: Bit 54 of the UPS specific fault register set. 0x0A6E UPS: Bit 54 of the UPS specific fault register cleared. 0x0A6F UPS: Bit 55 of the UPS specific fault register set. 0x0A70 UPS: Bit 55 of the UPS specific fault register cleared. 0x0A71 UPS: Bit 56 of the UPS specific fault register set. 0x0A72 UPS: Bit 56 of the UPS specific fault register cleared. 0x0A73 UPS: Bit 57 of the UPS specific fault register set. 0x0A74 UPS: Bit 57 of the UPS specific fault register cleared. 0x0A75 UPS: Bit 58 of the UPS specific fault register set. 0x0A76 UPS: Bit 58 of the UPS specific fault register cleared. 0x0A77 UPS: Bit 59 of the UPS specific fault register set. 0x0A78 UPS: Bit 59 of the UPS specific fault register cleared. 0x0A79 UPS: Bit 60 of the UPS specific fault register set. 0x0A7A UPS: Bit 60 of the UPS specific fault register cleared. 0x0A7B UPS: Bit 61 of the UPS specific fault register set. 0x0A7C UPS: Bit 61 of the UPS specific fault register cleared. 0x0A7D UPS: Bit 62 of the UPS specific fault register set. 0x0A7E UPS: Bit 62 of the UPS specific fault register cleared. 0x0A7F UPS: Bit 63 of the UPS specific fault register set. 0x0A80 UPS: Bit 63 of the UPS specific fault register cleared. 0x0301 Environment: Contact fault. 0x0302 Environment: Contact fault cleared. 0x0303 Environment: Contact fault. 0x0304 Environment: Contact fault cleared. 0x0305 Environment: Contact fault. 0x0306 Environment: Contact fault cleared. 0x0307 Environment: Contact fault. 0x0308 Environment: Contact fault cleared. 0x0309 Environment: Temperature threshold violation on probe 1. 0x030A Environment: Temperature threshold violation on probe 1 cleared. 0x030B Environment: Temperature threshold violation on probe 1. 0x030C Environment: Temperature threshold violation on probe 1 cleared. 0x030D Environment: Humidity threshold violation on probe 1. 0x030E Environment: Humidity threshold violation on probe 1 cleared. 0x030F Environment: Humidity threshold violation on probe 1. 0x0310 Environment: Humidity threshold violation on probe 1 cleared. 0x0311 Environment: Temperature threshold violation on probe 2. 0x0312 Environment: Temperature threshold violation on probe 2 cleared. 0x0313 Environment: Temperature threshold violation on probe 2. 0x0314 Environment: Temperature threshold violation on probe 2 cleared. 0x0315 Environment: Humidity threshold violation on probe 2. 0x0316 Environment: Humidity threshold violation on probe 2 cleared. 0x0317 Environment: Humidity threshold violation on probe 2. 0x0318 Environment: Humidity threshold violation on probe 2 cleared. 6

7 0x0319 Environment: Communications established. 0x031A Environment: Communications lost. SU = Smart-UPS Model UPSs SUDP = Smart-UPS DP Model UPSs MX = Matrix-UPS Model UPSs SY = Symmetra Power Array Model UPSs DP300E = Silcon DP300E Series Model UPSs 1 = Only Smart-UPS RM 2U model UPSs support this event 2 = Only Symmetra RM model UPSs support this event 3 = DP300E Parallel System in Hot Standby Mode will signal this event 4 = Non-Specific fault will not be signaled if Silcon Triple Chassis supports the UPS Specific Fault Register. Instead the specifc fault event will be signaled (see 0x0A01-0x0A80). 7