A SINGLE-STAGE POWER CONVERSION PV-BATTERY SYSTEM USING RECONFIGURABLE SOLAR CONVERTER

Size: px
Start display at page:

Download "A SINGLE-STAGE POWER CONVERSION PV-BATTERY SYSTEM USING RECONFIGURABLE SOLAR CONVERTER"

Transcription

1 A SINGLE-STAGE POWER CONVERSION PV-BATTERY SYSTEM USING RECONFIGURABLE SOLAR CONVERTER G.MADHU MARAIAH M.Tech Student Scholar, Department of Electrical & Electronics Engineering, KSRM College of Engineering, Kadapa Kadapa(Dt), A.P, India Abstract-- This paper introduces a Reconfigurable Solar Converter (RSC). This RSC finds wide application in grid connected solar system since it uses single stage conversion instead of multistage conversion, reduced losses, low cost, simple in construction, improved efficiency and reduced volume. The main concept of the RSC is to prefer single stage power converter on behalf of multistage converter for dc/ac and dc/dc operation for solar energy storage applications. Index Terms: Converter, energy storage, photovoltaic (PV), solar. I. INTRODUCTION SOLAR photovoltaic (PV) electricity generation is not available and sometimes less available depending on the time of the day and the weather conditions. Solar PV electricity output is also highly sensitive to shading. When even a small portion of a cell, module, or array is shaded, while the remainder is in sunlight, the output falls dramatically. Therefore, solar PV electricity output significantly varies. From an energy source standpoint, a stable energy source and an energy source that can be dispatched at the request are desired. As a result, energy storage such as batteries and fuel cells for solar PV systems has drawn significant attention and the demand of energy storage for solar PV systems has been dramatically increased, since, with energy storage, a solar PV system becomes a stable energy source and it can be dispatched at the request, which results in improving the performance and the value of solar PV systems. There are different options for integrating energy storage into a utility-scale solar PV system. Specifically, energy storage can be integrated into the either ac or dc side of the solar PV power conversion systems which may consist of multiple conversion stages. This project presents a new kind of single-stage solar converter called reconfigurable solar converter (RSC). The key notion of the RSC is to use a single power conversion system to achieve different operation methods such M.LAKSHMI NARYANA Assistant Professor, Department of Electrical & Electronics Engineering, KSRM College of Engineering, Kadapa Kadapa(Dt), A.P, India lakshminarayana.218@gmail.com as PV to grid (dc to ac), PV to battery (dc to dc), battery to grid (dc to ac), and battery/pv to grid (dc to ac) for solar PV systems with energy storage. Fig. 1. Different scenarios for PV generation and load supply sequence. The RSC notion evolved from the fact that energy storage combination for utility-scale solar PV systems makes sense if there is an enough gap or a minimal overlap between the PV energy storage and release time. Fig. 1 shows different scenarios for the PV generated power time of use. In case (a), the PV energy is always delivered to the grid and there is basically no need of energy storage. In cases (b) and (c), the PV energy should be first stored in the battery and then the battery or both battery and PV supply the load. In cases (b) and (c), integration of the battery has the highest value and the RSC provides significant benefit over other integration options when there is the time gap between generation and consumption of power. A. Introduction II. PROPOSED RSC Fig. 2. Proposed RSC circuit

2 The schematic of the proposed RSC is presented in Fig. 2. The RSC has some modifications to the conventional three-phase PV inverter system. These modifications allow the RSC to include the charging function in the conventional three phase PV inverter system. Assuming that the conventional utility-scale PV inverter system consists of a three-phase voltage source converter and its associated components, the RSC requires additional cables and mechanical switches, as shown in Fig. 2. Optional inductors are included if the ac filter inductance is not enough for the charging purpose. B. Operation Modes of the RSC The five possible operation modes for the proposed system are as follows. a) Mode 1: PV to grid (S 1 and S 6 switches close remain open) In this mode the solar panels are directly connected to the grid with Maximum Power Point Tracking (MPPT) by a dc/ac operation of the RSC. d) Mode 4: battery to grid (switch S 4 & S 6 open remaining switches are closed) In this mode delivers the energy from battery to grid. Fig. 3(d) C. System Advantages of Solar Power Plant with the RSC Concept The RSC provides significant merits to solar power plants. The current state-of-the-art technology is to integrate the energy storage into the ac side of the solar system. It can be utilized as a mean for shifting peak hours to solar power plants. This technique allows the system owners to have a strong asset which helps them to plan and operate the power plant with respect to their needs. The RSC has reduced conversion stages, high efficiency, low cost & simple in design etc. Fig. 3(a) b) Mode 2: PV to battery (switch S 6 close & S 5, S 3 open) In this mode the solar panels charge the batteries through dc/dc operation of the converter. In this mode it is possible to track maximum power with the help of MPPT algorithm. Fig. 3(b) c) Mode 3: PV/battery to grid (switch S 6 open & remaining switches are close) In this mode both the solar panels and batteries are connected to the grid by closing the switch S 1. Fig. 4. Utility-scale PV-energy storage systems with the RSC and the current state-of-the-art solution. D. System Control Schemes In response to the request of the grid operator, different system control techniques can be realized with the RSC solar power plants and are as follows: 1) System control 1 for Pgen > Preq ; 2) System control 2 for Pgen < Preq ; 3) System control 3 for Pgen = Preq ; 4) System control 4 for charging from grid (Mode 5) Fig. 3(c)

3 error. For the pulse width modulation (PWM) scheme, the conventional space vector PWM scheme is utilized. Fig. 6 presents the overall control block diagram of the RSC in the dc/ac operation. For the dc/ac operation with the battery, the RSC control should be coordinated with the battery management system (BMS), which is not shown in Fig. 6. Fig. 5. Different system operation modes of a RSC based solar PV power plant III. RSC CONTROL A. Control of the proposed RSC in the DC/AC Operation Modes (Modes 1, 3 & 4) The dc/ac operation of the RSC is utilized for delivering power from PV to grid, battery to grid, PV and battery to grid, and grid to battery. The RSC performs the MPPT algorithm to deliver maximum power from the PV to the grid. Like the conventional PV inverter control, the RSC control is implemented in the synchronous reference frame. The Fuzzy logic control is employed. In a reference frame rotating synchronously with the fundamental excitation, the fundamental excitation signals are transformed into dc signals. As a result, the current regulator forming the innermost loop of the control system is able to regulate ac currents over a wide frequency range with high bandwidth and zero steady-state B. Control of the proposed RSC in the DC/DC Operation Mode (Mode 2) The dc/dc operation of the RSC is also utilized for delivering the maximum power from the PV to the battery. The RSC in the dc/dc operation is a boost converter that controls the current flowing into the battery. In this research, Li-ion battery has been selected for the PV-battery systems. Li-ion batteries require a constant current, constant voltage type of charging algorithm. In other words, a Li-ion battery should be charged at a set current level until it reaches its final voltage. At the final voltage, the charging process should switch over to the constant voltage mode, and provide the current necessary to hold the battery at this final voltage. Thus, the dc/dc converter per forming charging process must be capable of providing stable control for maintaining either current or voltage at a constant value, depending on the state of the battery. Typically, a few percent capacity losses happen by not performing constant voltage charging. However, it is not uncommon only to use constant current charging to simplify the charging control and process. The latter has been used to charge the battery. Fig. 6. Overall control block diagram of the RSC in the dc/ac operation

4 Fig. 7. Overall control block diagram of the RSC in the dc/dc operation Therefore, from the control point of view, it is just sufficient to control only the inductor current. Like the dc/ac operation, the RSC performs the MPPT algorithm to deliver maximum power from the PV to the battery in the dc/dc operation. Fig. 7 shows the overall control block diagram of the RSC in the dc/dc operation. In this mode, the RSC control should be coordinated with the BMS, which is not shown in Fig. 7. C. Design Considerations and Modifications to the Conventional Three-Phase PV Converter One of the most important requirements of the project is that a new power conversion solution for PV-battery systems must have minimal complexity and modifications to the conventional three-phase solar PV converter system. Therefore, it is necessary to investigate how a three-phase dc/ac converter operates as a dc/dc converter and what modifications should be made. It is common to use a LCL filter for a high-power three-phase PV converter and the RSC in the dc/dc operation is expected to use the inductors already available in the LCL filter. There are basically two types of inductors, coupled three-phase inductor and three single-phase inductors that can be utilized in the RSC circuit. Using all three phases of the coupled three-phase inductor in the dc/dc operation causes a significant drop in the inductance value due to inductor core saturation. Table I presents an example of inductance value of a coupled three-phase inductor for the dc/dc operation, which shows significant drop in the inductance value. The reduction in inductance value requires inserting additional inductors for the dc/dc operation which has been marked as optional in Fig. 2. To avoid extra inductors, only one phase can perform the dc/dc operation. However, when only one phase, for instance phase B, is utilized for the dc/dc operation with only either upper or lower three insulated-gate bipolar transistors (IGBTs) are turned OFF as complementary switching, the circulating current occurs in phases A and C through filter capacitors, the coupled inductor, and switches, resulting in significantly high current ripple in phase B current, as shown in Fig. 8. To prevent the circulating current in the dc/dc operation, the following two solutions are proposed; 1) All unused upper and lower IGBTs must be turned OFF; 2) The coupled inductor is replaced by three singlephase Inductors. While the first solution with a coupled inductor is straight-forward, using three single-phase inductors makes it possible to use all three phase legs for the dc/dc operation. There are two methods to utilize all three phase legs for the dc/dc operation: 1) Synchronous operation; 2) Interleaving operation. In the first solution, all three phase legs can operate synchronously with their own current control.

5 In this case, the battery can be charged with a higher current compared to the case with one-phase dc/dc operation. This leads to a faster charging time due to higher charging current capability. However, each phase operates with higher current ripples. Higher ripple current flowing into the battery and capacitor can have negative effects on the lifetime of the battery and capacitors. To overcome the aforementioned problem associated with the synchronous operation, phases B and C can be shifted by applying a phase offset. For the interleaving operation using three phase legs, phases B and C are shifted by 120 and 240, respectively. Fig.8. Circulating current path if one phase is used for the dc/dc operation of the RSC witha coupled three-phase inductor The inductor current control in interleaving operation re requires a different inductor current sampling scheme, as shown in Fig. 9. How-ever, for three-phase interleaving, a modified sampling scheme is required to measure the average currents for all three phases. Therefore, the sampling points for phases B and C must be shifted by 120 and 240, respectively [see Fig 9(b)], which may imply that computation required inductor current control for each phase should be done asynchronously. Using the interleaving operation reduces the ripples on the charging current flowing into the battery. Therefore, the filter capacitance value can be reduced significantly. Fig. 9. Inductor current sampling schemes in the interleaving operation (a) Two-phase interleaving, (b) Three-phase interleaving D) Mode Change Control The basic concept of the RSC is to use a single power electronics circuit to perform different operation modes such as PV to grid (dc to ac) and PV to battery (dc to dc) for PV systems with energy storage, as discussed earlier. Therefore, in addition to the converter control in each mode, the seamless transition between modes is also essential for the single stage converter operation. To change a mode, the single stage converter must be reconfigured by either disconnecting or connecting components such as the battery through contactors. It is very important to understand the dynamics of the single stage solar converter. Generally, it is necessary to understand the relay response time such as how much time it takes for a relay to completely close or open. Hence, the performance curves of all re-lays used in the RSC circuit must be investigated. All relays used in the RSC circuit have a maximum operating time equal to or smaller than 50 ms. All switching, which occur during mode change, are

6 done under zero or nearly zero current, except fault cases. To verify the operating time given in the datasheet of the relays, a test for one of the relays used is made. The operating time of the relay used for SChgDC in Fig. 8 is investigated during pre charging of the inverter capacitors. The captured waveforms are shown in Fig. 10.The relay signal inside the DSP is captured through a D/A converter. It takes 240 μs until the signal reaches a value, 12 V, that is high enough to trigger the relay switching. Once the operating voltage is applied to the relay, it takes 20 ms until the current starts flowing through the relay. In other words, it takes 20 ms for the relay to be fully closed. The measured relay operating time of 20 ms is only half of the value given in the datasheet. For all relays used in the circuit, 80 ms is used as the relay switching transient time for both closing and releasing Fig. 11. Highest layer of the RSC mode change control Fig, 12. States inside Normal Condition Fig. 10. Measured operating time of the relay The highest layer of the single stage solar converter mode change control is shown in Fig. 11. This layer consists of fault detection, fault reset, and normal operation. The basic fault detection such as detecting over current and overvoltage and fault management like turning off PWM signals are implemented inside the converter control executed in the inner most control loop. In this way, fast fault detection and protection are possible. In general, shutting down all PWM signals is able to clear the fault. In addition, all relays are forced to be opened. If the system is operating normal, the status of the system will be Normal Condition. Once the fault flag is set by detecting a fault, the status of the system will be changed to Fault Condition. In this status, all relays as well as PWM signals are turned off. When the system is in Fault Condition, the single stage converter control tries to clear a fault condition every 1 s. If a fault cannot be cleared, the system will remain in the Fault Condition. If a fault is cleared, Normal Condition will be reinstated. Inside Normal Condition, the system always starts with Mode 0, which is the shutdown mode. This allows the single stage converter to move to a new mode safely, after a fault is cleared. The control topology inside Normal Condition is presented in Fig. 12. The single stage converter control mode can be changed to any mode from the present mode. If Modes 1 or 2 are commanded, the state will change from Mode 0 to PVCharge1 and relay SChgDC will be closed. This will charge the capacitor Cdc through the resistor RChgDC. Once the dc voltage of the capacitor reaches 98% of the source voltage, the state will change to PVCharge2. This will also close relay SPV, while the re-lay SChgDC will remain closed, because no new action refers to this relay. To make sure that the relay SPV is fully closed, a delay of 80 ms, relay switching transient time, is used, as discussed earlier. For example, the procedure of Mode 1 is described. Let us assume that the current state is Mode1pre. The relay SChgDC is opened, so that the pre charging procedure is completed. Also, the three grid-switches Sag, Sbg, and Scg are closed and therefore the load is connected to the single stage converter. Furthermore, the relay SChg is opened and the control is set to Mode 1, which is dc/ac control. Because relay switching is included in the state Mode1pre, a delay of 80 ms is required to move to the state of Run Circuit. When the previous mode is 1, it is possible to directly move to Mode2pre. This would bypass the pre charging process since the capacitors of the inverter are required to be

7 connected to the PV side in both modes. All the actions from Mode2pre shown in Fig. 12 are executed. After 80 ms, the state moves to Run Circuit shown in Fig. 13. When the previous mode is Mode 2 and the new mode is Mode 1, the state directly moves from PWMOFF to Mode1pre and back to Run Circuit by avoiding the pre charge process. Fig. 15. Matlab/Simulink RSC modes tested in the lab Fig.13. Control topology inside Run Circuit The startup of Mode 4 is different from Modes 1 and 2, be-cause it connects the battery to the inverter instead of connecting the PV to it. But the pre charging procedure is quite the same. Only different relays are used STran for charging the capacitor Cdc through the resistance RTran and relay SBat for directly connecting the battery to the inverter. Then, the state Mode4pre closes the grid switches and sets the mode control to number 4, which is again dc/ac control. After Mode4pre, the state changes to Run Circuit. Going from Modes 1 or 2 to Mode 4 or vice versa is not as easy as the mode change between Modes 1 and 2. The dc voltage always has to be changed to either the battery voltage (coming from Mode 1 or 2) or the PV voltage (coming from Mode 4), which makes the mode change control to use Mode 0 for transition. This does not mean that the circuit needs to be fully de energized, since the pre charging resistances limit the current and can therefore take care of this process. IV. RESULTS OF THE RSC CIRCUIT B. Performance Investigation of the DC/AC Operation Modes Fig. 16 shows the steady-state performance of dc/ac control in Mode 1. In this test, the voltage on the dc side VDC of the inverter is set to 200 V. The current reference is set to 5 Apeak for the frequency of 60 Hz. As shown in Fig. 16, a satisfactory steady state performance is obtained. Fig. 17 shows the steady-state performance of dc/ac control in Mode 4. In the test, the voltage on the dc side VDC of the inverter is 118V which is the battery voltage. The current reference is set to 3 Apeak for the frequency of 60 Hz. As shown in Fig. 17, the satisfactory dc/ac steady-state performance is obtained. In Fig. 17, the current flowing into the battery is exhibited. The average battery charging current is 1.8 A. The battery charging current has about 0.85 Apk pk current ripple with the frequency of 60 Hz. Fig. 16. Steady state performance of dc/ac control in Mode 1 PV to grid A. Experimental Setup The RSC control algorithms are implemented with MATLAB/Simulink real-time workshop into TI DSP TMS320F The performance of the RSC in different operation modes has been tested extensively in the lab. In the following, the performance analysis of selected modes of operation shown in Fig. 15 will be presented. Fig. 17. Steady state performance of dc/ac control in Mode 4 battery to grid.

8 C. Performance Investigation of the DC/DC Operation Mode In Mode 2 (PV to battery), the three-phase inverter is used as a dc/dc converter. As explained, initially a coupled three phase inductor is used for the filter inductor to the inverter side. When only phase B is utilized for the dc/dc operation with only either upper or lower three IGBTs are turned off as complementary switching, the circulating current occurs in phases A and C through filter capacitors, the coupled inductor, and switches, resulting in significantly high current ripple in phase B current, as shown in Fig. 18(a), battery current is 0.55A. (a) (b) automatically. The result of the test is presented in Fig. 18(c) showing that the current in the other phases remains zero while the battery is charged. Fig. 19 shows the current going into the battery for the test shown in Fig. 18(c). The average phase B current is 5 A and the average battery current is also 5 A. The phase B ripple is 5 A pk pk and the battery current ripple is 1 Apk pk. The capacitor ripple current is about 4.2 Apk pk. Using three single- phase inductors enables the RSC to use all three phase legs in the dc/dc operation. As discussed earlier, there are two methods to utilize all three phase legs for the dc/dc operation. In the first approach, all three phase-legs operate synchronously with their own current controls. Fig. 20 shows the waveforms of the synchronous operation. The sum of all three phase currents is 5A, which means that each phase carries one-third of it. Therefore, it is possible to charge the battery with even a higher current, which leads to a faster charging time. However, each phase current shows the current ripple of 5 Apk pk. The battery current has the current ripple of 2 Apk pk and the capacitor current shows the current ripple of 12 A pk pk which is almost three times as high as the ripple current of the battery charging using a single phase leg. Higher ripple current flowing into the battery and capacitor can have negative effects on the lifetime of the battery and capacitors. As discussed earlier, using the interleaving operation can reduce the ripples on the charging current flowing into the battery. (c) Fig. 19. Steady-state capacitor and battery current for single-phase operation using three single-phase inductors in the dc/dc operation. Fig. 18. Steady state performance of the RSC with single phase operation in the dc/dc mode (Mode 2). (a) when switches unused are not turned OFF.(b) when switches unused are turned OFF. (c) when three single-phase inductors are used. To solve the aforementioned problem, as explained, two solutions are proposed. First, the switches unused are turned off and consequently the phase current presents much lower ripple as shown in Fig. 18(b). The average current in phase B is now 5 A with a ripple of 5 Apk pk while the current in phases A and C remains zero, battery current is 0.6A. This means no circulating current. The second solution is to use three single-phase inductors in the RSC circuit. As expected with single-phase operation in this mode, the circulating current is vanished Fig. 20. Steady state performance of the RSC with three-phase synchronous operation in the dc/dc mode.

9 (c) (d) Fig. 21. Steady state performance of the RSC with three-phase interleaved operation in the dc/dc mode. As shown in Fig. 21, the battery current has a ripple current of 0.2 Apk pk and the capacitor current has a ripple current of 1.5 Apk pk when the sum of all three phase currents is 5 A and the average battery current is 5 A. These current ripples are one third of the ripple currents for dc/dc control using a single phase leg and one-eighth of the ripple currents for dc/dc control using all three phase legs in synchronous operation, which means significant ripple reduction is achieved by interleaving operation. (e) (f) D. Performance Investigation of Mode Change Mode change control is the most important aspect of the RSC operation. To implement the mode change control, MATLAB/Simulink stateflow is used. Fig. 22 shows the experiment results of mode change control. As mentioned earlier, only Mode 0 (Shutdown), Mode 1 (PV to Grid), Mode 2 (PV to Battery), and Mode 4 (Battery to Grid) are tested with the experimental setup. All mode changes show satisfactory performance in both transient and steady states. As discussed in Section III, mode change either from or to Mode 4 is not as simple as the mode change between Modes 1 and 2, since the dc voltage must be changed to either the battery voltage or the PV voltage. In the mode transition either to or from Mode 4, Mode 0 is used for transition [see Figs.22(h) and 22(i)]. After Mode 0 as transition, the dc capacitor is either discharged or charged through the precharging resistance. Therefore, the dc voltage is changed to either the battery voltage or the PV voltage, as demonstrated in Fig. 22. (g) (i) (h) Fig. 22. Transient performance of mode change. (a) Modes 0 to 1. (b) Modes 0 to 2. (c) Modes 0 to 4. (d) Modes 1 to 0 and 0 to 2. (e) Modes 2 to 0. (f) Modes 4 to 0 and 0 to 2. (g) Modes 2 to 1. (h) Modes 2 to 4 and 4 to 0 and 0 to 2. (i) Modes 4 to 1. (a) (b) V. CONCLUSION This paper introduced a new converter called RSC for PV-battery application, particularly utility-scale PV-battery application. The basic concept of the RSC is to use a single power conversion system to perform different operation modes such as PV to grid (dc to

10 ac), PV to battery (dc to dc), battery to grid (dc to ac), and battery/pv to grid (dc to ac) for solar PV systems with energy storage. The proposed solution requires minimal complexity and modifications to the conventional three-phase solar PV converters for PVbattery systems. Therefore, the solution is very attractive for PV-battery application, because it minimizes the number of conversion stages, thereby improving efficiency and reducing cost, weight, and volume. Test results have been presented to verify the concept of the RSC and to demonstrate the attractive performance characteristics of the RSC. These results confirm that the RSC is an optimal solution for PVbattery power conversion systems. Although this paper focuses on three-phase application, the main concept can be applied to single-phase application. The proposed solution is also capable of providing potential benefits to other intermittent energy sources including wind energy. REFERENCES [1] U.S. Department of Energy, Solar energy grid integration systems-energy storage (SEGIS-ES), May [2] N.Benavidas and P.Chapman, Power budgeting of a multiple-input buck-boost converter, IEEE Trans.Power Electron., vol. 20, no. 6, pp , Nov [3] H. Konishi, T. Iwato, and M. Kudou, Development of large-scale power conditioning system in Hokuto mega-solar project, in Proc. Int. Power Electron. Conf., 2010, pp [4] J. H. Enslin and D. B. Snyman, Combined lowcost, high efficient inverter,peak power tracker and regulator for PV applications, IEEE Trans.Power Electron., vol. 6, no. 1, pp , Jan [5] H. Ertl, J. W. Kolar, and F. Zach, A novel multicell dc-ac converter for applications in renewable energy systems, IEEE Trans. Ind. Electron.,vol. 49, no. 5, pp , Oct [6] C. Zhao, S. D. Round, and J. W. Kolar, An isolated three-port bidirectional dc/dc converter with decoupled power flow management, IEEE Trans. Power Electron., vol. 23, no. 5, pp , Sep [7] M. Bragard, N. Soltau, R. W. De Doncker, and A. Schiemgel, Design and implementation of a 5 kw photovoltaic system with Li-ion battery and additional dc/dc converter, in Proc. IEEE Energy Convers. Congr. Expo., 2010, pp [8] W. Li, J. Xiao, Y. Zhao, and X. He, PWM plus phase angle shift control scheme for combined multiport dc/dc converters, IEEE Trans. Power Electron., vol. 27, no. 3, pp , Mar [9] P. Barrade, S.Delalay, and A. Rufer, Direct connection of super capacitors to photovoltaic panels with on-off maximum power point tracking, IEEE Trans. Sustainable Energy, vol. 3, no. 2, pp ,Apr [10] S. J. Chiang, K. T. Chang, and C. Y.Yen, Residential photovoltaic energy storage system, IEEE Trans. Ind. Electron., vol. 45, no. 3, pp , Jun [11] Z. Zhao, M. Xu, Q. Chen, J. Lai, and Y. Cho, Derivation, analysis, and implementation of a boostbuck converter-based high-efficiency PV inverter, IEEE Trans. Power Electron., vol. 27, no. 3, pp ,Mar [12] C. Ho, H. Breuninger, S. Pettersson, G. Escobar, L. Serpa, and A. Coccia, Practical design and implementation procedure of an interleaved boost converter using SiC diodes for PV applications, IEEE Trans. Power Electron., vol. 27, no. 6, pp , Jun [13] F. Ding, P. Li, B. Huang, F. Gao, C. Ding, and C. Wang, Modeling and Simulation of grid connected hybrid PV/battery distributed generation system, in Proc. China Int. Conf. Electr. Distrib., 2010, pp AUTHOR DETAILS: G.MADHU MARAIAH currently persuing his M.Tech in Electrical Power Systems from KSRM College of Engineering in Kadapa Affiliated to JNT University, Anantapuramu. He had done his B.Tech degree from KSRM College of Engineering in Kadapa Affiliated to SV University, Tirupati in 2012 and his field of interest includes Power Electronics and Power Systems. M. Lakshmi Naryana completed B.Tech in Electrical & Electronics Engineering from Narasaraopeta Engineering College in 2007, M.Tech in DSCE, PE&ED in Narasaraopeta Engineering College in Currently working as Asst. prof. in KSRM College of Engineering, Kadapa.

Single-Stage Reconfigurable Solar Converter for Grid-Linked System by using a fuzzy logic

Single-Stage Reconfigurable Solar Converter for Grid-Linked System by using a fuzzy logic www.ijecs.in International Journal Of Engineering And Computer Science ISSN:2319-7242 Volume 4 Issue 1 January 2015, Page No. 10195-10204 Single-Stage Reconfigurable Solar Converter for Grid-Linked System

More information

Grid Connected Hybrid Renewable Energy Power Generation by ZVS Based RSC with Single Stage Power Conversion

Grid Connected Hybrid Renewable Energy Power Generation by ZVS Based RSC with Single Stage Power Conversion Grid Connected Hybrid Renewable Energy Power Generation by ZVS Based RSC with Single Stage Power Conversion B. Madhava Dr. B. Venkata Prasanth, Dr. J. Viswanath Rao PG Scholar, Dept of EEE, Professor Dept.of

More information

A Novel DC-DC Converter Based Integration of Renewable Energy Sources for Residential Micro Grid Applications

A Novel DC-DC Converter Based Integration of Renewable Energy Sources for Residential Micro Grid Applications A Novel DC-DC Converter Based Integration of Renewable Energy Sources for Residential Micro Grid Applications Madasamy P 1, Ramadas K 2 Assistant Professor, Department of Electrical and Electronics Engineering,

More information

Multi-Port DC-DC Converter for Grid Integration of Photo Voltaic Systems through Storage Systems with High Step-Up Ratio

Multi-Port DC-DC Converter for Grid Integration of Photo Voltaic Systems through Storage Systems with High Step-Up Ratio Multi-Port DC-DC Converter for Grid Integration of Photo Voltaic Systems through Storage Systems with High Step-Up Ratio CH.Rekha M.Tech (Energy Systems), Dept of EEE, M.Vinod Kumar Assistant Professor,

More information

[Patil, 7(2) April-June 2017] ISSN: Impact Factor: 4.015

[Patil, 7(2) April-June 2017] ISSN: Impact Factor: 4.015 INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & MANAGEMENT A REVIEW PAPER BASED ON MULTI LEVEL INVERTER INTERFACING WITH SOLAR POWER GENERATION Sumit Dhanraj Patil 1, Sunil Kumar Bhatt 2 1 M.Tech. Student,

More information

International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering. (An ISO 3297: 2007 Certified Organization)

International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering. (An ISO 3297: 2007 Certified Organization) Modeling and Control of Quasi Z-Source Inverter for Advanced Power Conditioning Of Renewable Energy Systems C.Dinakaran 1, Abhimanyu Bhimarjun Panthee 2, Prof.K.Eswaramma 3 PG Scholar (PE&ED), Department

More information

Design and Implementation of Non-Isolated Three- Port DC/DC Converter for Stand-Alone Renewable Power System Applications

Design and Implementation of Non-Isolated Three- Port DC/DC Converter for Stand-Alone Renewable Power System Applications Design and Implementation of Non-Isolated Three- Port DC/DC Converter for Stand-Alone Renewable Power System Applications Archana 1, Nalina Kumari 2 1 PG Student (power Electronics), Department of EEE,

More information

INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET)

INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET) INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET) Proceedings of the 2 nd International Conference on Current Trends in Engineering and Management ICCTEM -2014 ISSN 0976 6545(Print)

More information

An Improved Efficiency of Integrated Inverter / Converter for Dual Mode EV/HEV Application

An Improved Efficiency of Integrated Inverter / Converter for Dual Mode EV/HEV Application An Improved Efficiency of Integrated Inverter / Converter for Dual Mode EV/HEV Application A. S. S. Veerendra Babu 1, P. Bala Krishna 2, R. Venkatesh 3 1 Assistant Professor, Department of EEE, ADITYA

More information

Page 1393

Page 1393 BESS based Multi input inverter for Grid connected hybrid pv and wind power system Seshadri Pithani 1, Mr.B,D.S.Prasad 2 1 PG Scholar, Pydah College of Engineering, Kakinada, AP, India. 2 Assistant Professor,

More information

APPLICATION OF BOOST INVERTER FOR GRID CONNECTED FUEL CELL BASED POWER GENERATION

APPLICATION OF BOOST INVERTER FOR GRID CONNECTED FUEL CELL BASED POWER GENERATION APPLICATION OF BOOST INVERTER FOR GRID CONNECTED FUEL CELL BASED POWER GENERATION P.Bhagyasri 1, N. Prasanth Babu 2 1 M.Tech Scholar (PS), Nalanda Institute of Engineering and Tech. (NIET), Kantepudi,

More information

Implementation of Bidirectional DC-DC converter for Power Management in Hybrid Energy Sources

Implementation of Bidirectional DC-DC converter for Power Management in Hybrid Energy Sources Implementation of Bidirectional DC-DC converter for Power Management in Hybrid Energy Sources Inturi Praveen M.Tech-Energy systems, Department of EEE, JBIET-Hyderabad, Telangana, India. G Raja Sekhar Associate

More information

Implementation Soft Switching Bidirectional DC- DC Converter For Stand Alone Photovoltaic Power Generation System

Implementation Soft Switching Bidirectional DC- DC Converter For Stand Alone Photovoltaic Power Generation System IJIRST International Journal for Innovative Research in Science & Technology Volume 1 Issue 6 November 2014 ISSN (online): 2349-6010 Implementation Soft Switching Bidirectional DC- DC Converter For Stand

More information

A Bidirectional Universal Dc/Dc Converter Topology for Electric Vehicle Applicationsand Photovoltaic Applications

A Bidirectional Universal Dc/Dc Converter Topology for Electric Vehicle Applicationsand Photovoltaic Applications International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 10, Issue 1 (February 2014), PP. 04-10 A Bidirectional Universal Dc/Dc Converter

More information

Research Paper MULTIPLE INPUT BIDIRECTIONAL DC-DC CONVERTER Gomathi.S 1, Ragavendiran T.A. S 2

Research Paper MULTIPLE INPUT BIDIRECTIONAL DC-DC CONVERTER Gomathi.S 1, Ragavendiran T.A. S 2 Research Paper MULTIPLE INPUT BIDIRECTIONAL DC-DC CONVERTER Gomathi.S 1, Ragavendiran T.A. S 2 Address for Correspondence M.E.,(Ph.D).,Assistant Professor, St. Joseph s institute of Technology, Chennai

More information

Bidirectional Intelligent Semiconductor Transformer

Bidirectional Intelligent Semiconductor Transformer Journal of Engineering and Fundamentals Vol. 2(2), pp. 9-16, December, 2015 Available online at http://www.tjef.net ISSN: 2149-0325 http://dx.doi.org/10.17530/jef.15.08.2.2 Article history Received: 24.05.2015

More information

POWER ELECTRONICS & DRIVES

POWER ELECTRONICS & DRIVES POWER ELECTRONICS & DRIVES S.No Title Year Solar Energy/PV Grid-Tied 01 Nonlinear PWM-Controlled Single-Phase Boost Mode Grid-Connected Photovoltaic Inverter With Limited Storage Inductance Current 02

More information

A.Arun 1, M.Porkodi 2 1 PG student, 2 Associate Professor. Department of Electrical Engineering, Sona College of Technology, Salem, India

A.Arun 1, M.Porkodi 2 1 PG student, 2 Associate Professor. Department of Electrical Engineering, Sona College of Technology, Salem, India A novel anti-islanding technique in a Distributed generation systems A.Arun 1, M.Porkodi 2 1 PG student, 2 Associate Professor Department of Electrical Engineering, Sona College of Technology, Salem, India

More information

Design and Development of Bidirectional DC-DC Converter using coupled inductor with a battery SOC indication

Design and Development of Bidirectional DC-DC Converter using coupled inductor with a battery SOC indication Design and Development of Bidirectional DC-DC Converter using coupled inductor with a battery SOC indication Sangamesh Herurmath #1 and Dr. Dhanalakshmi *2 # BE,MTech, EEE, Dayananda Sagar institute of

More information

EXPERIMENTAL VERIFICATION OF INDUCED VOLTAGE SELF- EXCITATION OF A SWITCHED RELUCTANCE GENERATOR

EXPERIMENTAL VERIFICATION OF INDUCED VOLTAGE SELF- EXCITATION OF A SWITCHED RELUCTANCE GENERATOR EXPERIMENTAL VERIFICATION OF INDUCED VOLTAGE SELF- EXCITATION OF A SWITCHED RELUCTANCE GENERATOR Velimir Nedic Thomas A. Lipo Wisconsin Power Electronic Research Center University of Wisconsin Madison

More information

INVESTIGATION AND PERFORMANCE ANALYSIS OF MULTI INPUT CONVERTER FOR THREE PHASE NON CONVENTIONAL ENERGY SOURCES FOR A THREE PHASE INDUCTION MOTOR

INVESTIGATION AND PERFORMANCE ANALYSIS OF MULTI INPUT CONVERTER FOR THREE PHASE NON CONVENTIONAL ENERGY SOURCES FOR A THREE PHASE INDUCTION MOTOR Man In India, 96 (12) : 5421-5430 Serials Publications INVESTIGATION AND PERFORMANCE ANALYSIS OF MULTI INPUT CONVERTER FOR THREE PHASE NON CONVENTIONAL ENERGY SOURCES FOR A THREE PHASE INDUCTION MOTOR

More information

Modeling and Simulation of Multi-input Bi-directional Boost Converter for Renewable Energy Applications using MatLab/Simulink

Modeling and Simulation of Multi-input Bi-directional Boost Converter for Renewable Energy Applications using MatLab/Simulink Modeling and Simulation of Multi-input Bi-directional Boost Converter for Renewable Energy Applications using MatLab/Simulink Ramya. S Assistant Professor, ECE P.A. College of Engineering and Technology,

More information

IJREE - International Journal of Research in Electrical Engineering ISSN:

IJREE - International Journal of Research in Electrical Engineering ISSN: ISSN: 2349-2503 SOLAR GRID WITH FAULT RIDE THROUGH WITH SINGLE AND DUAL STAGE INVERTER UNDER FAULT CONDITION E. Tej Deepti 1 M.Rama Subbamma 2 1 (Dept of EEE. MTech Scholar, Global College of Engineering

More information

Inverter with MPPT and Suppressed Leakage Current

Inverter with MPPT and Suppressed Leakage Current POWER ELECTRONICS IEEE Projects Titles -2018 LeMeniz Infotech 36, 100 feet Road, Natesan Nagar(Near Indira Gandhi Statue and Next to Fish-O-Fish), Pondicherry-605 005 Web : www.ieeemaster.com / www.lemenizinfotech.com

More information

IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 02, 2016 ISSN (online):

IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 02, 2016 ISSN (online): IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 02, 2016 ISSN (online): 2321-0613 Bidirectional Double Buck Boost Dc- Dc Converter Malatesha C Chokkanagoudra 1 Sagar B

More information

Development of Novel Connection Control Method for Small Scale Solar - Wind Hybrid Power Plant

Development of Novel Connection Control Method for Small Scale Solar - Wind Hybrid Power Plant Development of Novel Connection Control Method for Small Scale Solar - Wind Hybrid Power Plant Vu Minh Phap*, N. Yamamura, M. Ishida, J. Hirai, K. Nakatani Department of Electrical and Electronic Engineering,

More information

Simulation of Fully-Directional Universal DC- DC Converter for Electric Vehicle Applications

Simulation of Fully-Directional Universal DC- DC Converter for Electric Vehicle Applications Simulation of Fully-Directional Universal DC- DC Converter for Electric Vehicle Applications Saikrupa C Iyer* R. M. Sahdhashivapurhipurun Sandhya Sriraman Tulsi S Ramanujam R. Ramaprabha Department of

More information

Simulation Modeling and Control of Hybrid Ac/Dc Microgrid

Simulation Modeling and Control of Hybrid Ac/Dc Microgrid Research Inventy: International Journal of Engineering And Science Vol.6, Issue 1 (January 2016), PP -17-24 Issn (e): 2278-4721, Issn (p):2319-6483, www.researchinventy.com Simulation Modeling and Control

More information

Design of Three Input Buck-Boost DC-DC Converter with Constant input voltage and Variable duty ratio using MATLAB/Simulink

Design of Three Input Buck-Boost DC-DC Converter with Constant input voltage and Variable duty ratio using MATLAB/Simulink Design of Three Input Buck-Boost DC-DC Converter with Constant input voltage and Variable duty ratio using MATLAB/Simulink A.Thiyagarajan, B.Gokulavasan Abstract Nowadays DC-DC converter is mostly used

More information

Sensor less Control of BLDC Motor using Fuzzy logic controller for Solar power Generation

Sensor less Control of BLDC Motor using Fuzzy logic controller for Solar power Generation Sensor less Control of BLDC Motor using Fuzzy logic controller for Solar power Generation A. Sundaram 1 and Dr. G.P. Ramesh 2 1 Department of Electrical and Electronics Engineering, St. Peter s University,

More information

Soft Switching of Two Quadrant Forward Boost and Reverse Buck DC- DC Converters Sarath Chandran P C 1

Soft Switching of Two Quadrant Forward Boost and Reverse Buck DC- DC Converters Sarath Chandran P C 1 IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 02, 2015 ISSN (online): 2321-0613 Soft Switching of Two Quadrant Forward Boost and Reverse Buck DC- DC Converters Sarath

More information

A Novel GUI Modeled Fuzzy Logic Controller for a Solar Powered Energy Utilization Scheme

A Novel GUI Modeled Fuzzy Logic Controller for a Solar Powered Energy Utilization Scheme 1 A Novel GUI Modeled Fuzzy Logic Controller for a Solar Powered Energy Utilization Scheme I. H. Altas 1, * and A.M. Sharaf 2 ihaltas@altas.org and sharaf@unb.ca 1 : Dept. of Electrical and Electronics

More information

BIDIRECTIONAL DC-DC CONVERTER FOR INTEGRATION OF BATTERY ENERGY STORAGE SYSTEM WITH DC GRID

BIDIRECTIONAL DC-DC CONVERTER FOR INTEGRATION OF BATTERY ENERGY STORAGE SYSTEM WITH DC GRID BIDIRECTIONAL DC-DC CONVERTER FOR INTEGRATION OF BATTERY ENERGY STORAGE SYSTEM WITH DC GRID 1 SUNNY KUMAR, 2 MAHESWARAPU SYDULU Department of electrical engineering National institute of technology Warangal,

More information

International Journal Of Global Innovations -Vol.2, Issue.I Paper Id: SP-V2-I1-048 ISSN Online:

International Journal Of Global Innovations -Vol.2, Issue.I Paper Id: SP-V2-I1-048 ISSN Online: Multilevel Inverter Analysis and Modeling in Distribution System with FACTS Capability #1 B. PRIYANKA - M.TECH (PE Student), #2 D. SUDHEEKAR - Asst Professor, Dept of EEE HASVITA INSTITUTE OF MANAGEMENT

More information

The hierarchical three layer protection of photovoltaic generators in microgrid with co-ordinated droop control for hybrid energy storage system

The hierarchical three layer protection of photovoltaic generators in microgrid with co-ordinated droop control for hybrid energy storage system The hierarchical three layer protection of photovoltaic generators in microgrid with co-ordinated droop control for hybrid energy storage system Vignesh, Student Member, IEEE, Sundaramoorthy, Student Member,

More information

Analysis and Design of Improved Isolated Bidirectional Fullbridge DC-DC Converter for Hybrid Electric Vehicle

Analysis and Design of Improved Isolated Bidirectional Fullbridge DC-DC Converter for Hybrid Electric Vehicle Analysis and Design of Improved Isolated Bidirectional Fullbridge DC-DC Converter for Hybrid Electric Vehicle Divya K. Nair 1 Asst. Professor, Dept. of EEE, Mar Athanasius College Of Engineering, Kothamangalam,

More information

Power Electronics Projects

Power Electronics Projects Power Electronics Projects I. POWER ELECTRONICS based MULTI-PORT SYSTEMS 1. Analysis, Design, Modeling, and Control of an Interleaved- Boost Full-ridge Three-Port Converter for Hybrid Renewable Energy

More information

Design and Modelling of Induction Generator Wind power Systems by using MATLAB/SIMULINK

Design and Modelling of Induction Generator Wind power Systems by using MATLAB/SIMULINK Design and Modelling of Induction Generator Wind power Systems by using MATLAB/SIMULINK G. Hima Bindu 1, Dr. P. Nagaraju Mandadi 2 PG Student [EPS], Dept. of EEE, Sree Vidyanikethan Engineering College,

More information

SPIRO SOLUTIONS PVT LTD POWER ELECTRONICS 1. RENEWABLE ENERGY PROJECT TITLES I. SOLAR ENERGY

SPIRO SOLUTIONS PVT LTD POWER ELECTRONICS 1. RENEWABLE ENERGY PROJECT TITLES I. SOLAR ENERGY POWER ELECTRONICS 1. RENEWABLE ENERGY S.NO PROJECT CODE PROJECT TITLES I. SOLAR ENERGY YEAR 1 ITPW01 Photovoltaic Module Integrated Standalone Single Stage Switched Capacitor Inverter with Maximum Power

More information

Control Scheme for Grid Connected WECS Using SEIG

Control Scheme for Grid Connected WECS Using SEIG Control Scheme for Grid Connected WECS Using SEIG B. Anjinamma, M. Ramasekhar Reddy, M. Vijaya Kumar, Abstract: Now-a-days wind energy is one of the pivotal options for electricity generation among all

More information

Development and Analysis of Bidirectional Converter for Electric Vehicle Application

Development and Analysis of Bidirectional Converter for Electric Vehicle Application Development and Analysis of Bidirectional Converter for Electric Vehicle Application N.Vadivel, A.Manikandan, G.Premkumar ME (Power Electronics and Drives) Department of Electrical and Electronics Engineering

More information

Simulation Analysis of Closed Loop Dual Inductor Current-Fed Push-Pull Converter by using Soft Switching

Simulation Analysis of Closed Loop Dual Inductor Current-Fed Push-Pull Converter by using Soft Switching Journal for Research Volume 02 Issue 04 June 2016 ISSN: 2395-7549 Simulation Analysis of Closed Loop Dual Inductor Current-Fed Push-Pull Converter by using Soft Switching Ms. Manasa M P PG Scholar Department

More information

1. RENEWABLE ENERGY I.SOLAR ENERGY PROJECT TITLES WE CAN ALSO IMPLEMENT YOUR OWN CONCEPT/IDEA

1. RENEWABLE ENERGY I.SOLAR ENERGY PROJECT TITLES WE CAN ALSO IMPLEMENT YOUR OWN CONCEPT/IDEA 1. RENEWABLE ENERGY I.SOLAR ENERGY S.NO PROJECT CODE PROJECT TITLES YEAR 1 ITPW01 Highly efficient asymmetrical pwm full-bridge renewable energy sources converter for 2 ITPW02 A Three Phase Hybrid Cascaded

More information

COMPARISON OF PID AND FUZZY CONTROLLED DUAL INVERTER-BASED SUPER CAPACITOR FOR WIND ENERGY CONVERSION SYSTEMS

COMPARISON OF PID AND FUZZY CONTROLLED DUAL INVERTER-BASED SUPER CAPACITOR FOR WIND ENERGY CONVERSION SYSTEMS COMPARISON OF PID AND FUZZY CONTROLLED DUAL INVERTER-BASED SUPER CAPACITOR FOR WIND ENERGY CONVERSION SYSTEMS R. Vinu Priya 1, M. Ramasekharreddy 2, M. Vijayakumar 3 1 PG student, Dept. of EEE, JNTUA College

More information

A Novel Hybrid PV/Wind/Battery based Generation System for Grid Integration

A Novel Hybrid PV/Wind/Battery based Generation System for Grid Integration A Novel Hybrid PV/Wind/Battery based Generation System for Grid Integration B.Venkata Seshu Babu M.Tech (Power Systems), St. Ann s College of Engineering & Technology, A.P, India. Abstract: A hybrid wind/pv

More information

NOVEL MODULAR MULTIPLE-INPUT BIDIRECTIONAL DC DC POWER CONVERTER (MIPC) FOR HEV/FCV APPLICATION

NOVEL MODULAR MULTIPLE-INPUT BIDIRECTIONAL DC DC POWER CONVERTER (MIPC) FOR HEV/FCV APPLICATION NOVEL MODULAR MULTIPLE-INPUT BIDIRECTIONAL DC DC POWER CONVERTER (MIPC) FOR HEV/FCV APPLICATION 1 Anitha Mary J P, 2 Arul Prakash. A, 1 PG Scholar, Dept of Power Electronics Egg, Kuppam Engg College, 2

More information

Hybrid Three-Port DC DC Converter for PV-FC Systems

Hybrid Three-Port DC DC Converter for PV-FC Systems Hybrid Three-Port DC DC Converter for PV-FC Systems P Srihari Babu M.Tech (Power Systems) B Ashok Kumar Assistant Professor Dr. A.Purna Chandra Rao Professor & HoD Abstract The proposed a hybrid power

More information

Isolated Bidirectional DC DC Converter for SuperCapacitor Applications

Isolated Bidirectional DC DC Converter for SuperCapacitor Applications European Association for the Development of Renewable Energies, Environment and Power Quality (EA4EPQ) International Conference on Renewable Energies and Power Quality (ICREPQ 11) Las Palmas de Gran Canaria

More information

Design of Active and Reactive Power Control of Grid Tied Photovoltaics

Design of Active and Reactive Power Control of Grid Tied Photovoltaics IJCTA, 9(39), 2016, pp. 187-195 International Science Press Closed Loop Control of Soft Switched Forward Converter Using Intelligent Controller 187 Design of Active and Reactive Power Control of Grid Tied

More information

Photovoltaic Based EV/HEV for Bi-Directional operation in AC and DC Grid with PWM Control and PV Converters

Photovoltaic Based EV/HEV for Bi-Directional operation in AC and DC Grid with PWM Control and PV Converters Photovoltaic Based EV/HEV for Bi-Directional operation in AC and DC Grid with PWM Control and PV Converters Sahu Gopi Gowri Santosh Kumar M-Tech Student Scholar, Department of Electrical & Electronics

More information

Design and Implementation of an 11-Level Inverter with FACTS Capability for Distributed Energy Systems

Design and Implementation of an 11-Level Inverter with FACTS Capability for Distributed Energy Systems Design and Implementation of an 11-Level Inverter with FACTS Capability for Distributed Energy Systems Pinnam Swetha M.Tech Student KSRM College of Engineering, Kadapa, A.P. Abstract: In this paper, a

More information

Renewable Energy Sources Based EV/HEV for Bi-Directional Operation in AC and DC Grid

Renewable Energy Sources Based EV/HEV for Bi-Directional Operation in AC and DC Grid Renewable Energy Sources Based EV/HEV for Bi-Directional Operation in AC and DC Grid Routhu Trimurtulu M.Tech Student Scholar, Department of Electrical & Electronics Engineering, Thandra Paparaya Institute

More information

PERFORMANCE AND ENHANCEMENT OF Z-SOURCE INVERTER FED BLDC MOTOR USING SLIDING MODE OBSERVER

PERFORMANCE AND ENHANCEMENT OF Z-SOURCE INVERTER FED BLDC MOTOR USING SLIDING MODE OBSERVER PERFORMANCE AND ENHANCEMENT OF Z-SOURCE INVERTER FED BLDC MOTOR USING SLIDING MODE OBSERVER K.Kalpanadevi 1, Mrs.S.Sivaranjani 2, 1 M.E. Power Systems Engineering, V.S.B.Engineering College, Karur, Tamilnadu,

More information

Dual power flow Interface for EV, HEV, and PHEV Applications

Dual power flow Interface for EV, HEV, and PHEV Applications International Journal of Engineering Inventions e-issn: 2278-7461, p-issn: 2319-6491 Volume 4, Issue 4 [Sep. 2014] PP: 20-24 Dual power flow Interface for EV, HEV, and PHEV Applications J Ranga 1 Madhavilatha

More information

Design of Four Input Buck-Boost DC-DC Converter for Renewable Energy Application

Design of Four Input Buck-Boost DC-DC Converter for Renewable Energy Application Design of Four Input Buck-Boost DC-DC Converter for Renewable Energy Application A.Thiyagarajan Assistant Professor, Department of Electrical and Electronics Engineering Karpagam Institute of Technology

More information

Power Management with Solar PV in Grid-connected and Stand-alone Modes

Power Management with Solar PV in Grid-connected and Stand-alone Modes Power Management with Solar PV in Grid-connected and Stand-alone Modes Sushilkumar Fefar, Ravi Prajapati, and Amit K. Singh Department of Electrical Engineering Institute of Infrastructure Technology Research

More information

The Master of IEEE Projects. LeMenizInfotech. 36, 100 Feet Road, Natesan Nagar, Near Indira Gandhi Statue, Pondicherry

The Master of IEEE Projects. LeMenizInfotech. 36, 100 Feet Road, Natesan Nagar, Near Indira Gandhi Statue, Pondicherry An Interleaved Half-Bridge Three-Port Converter With Enhanced Power Transfer Capability Using Three-Leg Rectifier for Renewable Energy Applications Introduction: Renewable energy power systems attract

More information

A Study of Suitable Bi-Directional DC-DC Converter Topology Essential For Battery Charge Regulation In Photovoltaic Applications

A Study of Suitable Bi-Directional DC-DC Converter Topology Essential For Battery Charge Regulation In Photovoltaic Applications IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 11, Issue 2 Ver. I (Mar. Apr. 2016), PP 92-96 www.iosrjournals.org A Study of Suitable Bi-Directional

More information

Input-Series-Output-Parallel Connected DC/DC Converter for a Photovoltaic PCS with High Efficiency under a Wide Load Range

Input-Series-Output-Parallel Connected DC/DC Converter for a Photovoltaic PCS with High Efficiency under a Wide Load Range Input-Series-Output-Parallel Connected DC/DC Converter for a Photovoltaic PCS with 9 JPE 10-1-2 Input-Series-Output-Parallel Connected DC/DC Converter for a Photovoltaic PCS with High Efficiency under

More information

BI-DIRECTIONAL DC-DC CONVERTER FOR ENERGY STORAGE IN SOLAR PV SYSTEM

BI-DIRECTIONAL DC-DC CONVERTER FOR ENERGY STORAGE IN SOLAR PV SYSTEM Volume 120 No. 6 2018, 1101-1111 ISSN: 1314-3395 (on-line version) url: http://www.acadpubl.eu/hub/ http://www.acadpubl.eu/hub/ BI-DIRECTIONAL DC-DC CONVERTER FOR ENERGY STORAGE IN SOLAR PV SYSTEM M.Sairam

More information

To Increase System Efficiency for Portable Electronics Devices with DC-DC Converter

To Increase System Efficiency for Portable Electronics Devices with DC-DC Converter To Increase System Efficiency for Portable Electronics Devices with DC-DC Converter Miss. BHAGYASHREE N. PIKALMUNDE, Mr. VINOD BHONGADE 1 Student,R.C.E.R.T Chandrapur, bhaghyshree444@gmail.com, Mob.no.08421134324

More information

Power Electronics & Drives [Simulink, Hardware-Open & Closed Loop]

Power Electronics & Drives [Simulink, Hardware-Open & Closed Loop] Power Electronics & [Simulink, Hardware-Open & Closed Loop] Project code Project theme Application ISTPOW801 Estimation of Stator Resistance in Direct Torque Control Synchronous Motor ISTPOW802 Open-Loop

More information

SOLAR PHOTOVOLTAIC ARRAY FED WATER PUMP RIVEN BY BRUSHLESS DC MOTOR USING KY CONVERTER

SOLAR PHOTOVOLTAIC ARRAY FED WATER PUMP RIVEN BY BRUSHLESS DC MOTOR USING KY CONVERTER SOLAR PHOTOVOLTAIC ARRAY FED WATER PUMP RIVEN BY BRUSHLESS DC MOTOR USING KY CONVERTER B.Dinesh, Mail Id: dineshtata911@gmail.com M.k.Jaivinayagam, Mail Id: jaivimk5678@gmail.com M.Udayakumar, Mail Id:

More information

ANFIS CONTROL OF ENERGY CONTROL CENTER FOR DISTRIBUTED WIND AND SOLAR GENERATORS USING MULTI-AGENT SYSTEM

ANFIS CONTROL OF ENERGY CONTROL CENTER FOR DISTRIBUTED WIND AND SOLAR GENERATORS USING MULTI-AGENT SYSTEM ANFIS CONTROL OF ENERGY CONTROL CENTER FOR DISTRIBUTED WIND AND SOLAR GENERATORS USING MULTI-AGENT SYSTEM Mr.SK.SHAREEF 1, Mr.K.V.RAMANA REDDY 2, Mr.TNVLN KUMAR 3 1PG Scholar, M.Tech, Power Electronics,

More information

Fuzzy logic controlled Bi-directional DC-DC Converter for Electric Vehicle Applications

Fuzzy logic controlled Bi-directional DC-DC Converter for Electric Vehicle Applications IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 12, Issue 3 Ver. IV (May June 2017), PP 51-55 www.iosrjournals.org Fuzzy logic controlled

More information

DC Microgrids and Distribution Systems for Residences

DC Microgrids and Distribution Systems for Residences Microgrids and Distribution Systems for Residences Toshifumi ISE, Hiroaki KAKIGANO (Osaka University, JAPAN) Outline of the Presentation 1. Introduction 2. System Configuration and Control Scheme 3. System

More information

I.INTRODUCTION. INDEX TERMS Energy management, grid control, grid operation,hybrid microgrid, PV system, wind power generation.

I.INTRODUCTION. INDEX TERMS Energy management, grid control, grid operation,hybrid microgrid, PV system, wind power generation. International Journal of Advances in Applied Science and Engineering (IJAEAS) ISSN (P): 2348-1811; ISSN (E): 2348-182X Vol. 3, Issue 3, July 2016, 14-20 IIST Grid-Connected Photovoltaic System Based on

More information

Dynamic Modelling of Hybrid System for Efficient Power Transfer under Different Condition

Dynamic Modelling of Hybrid System for Efficient Power Transfer under Different Condition RESEARCH ARTICLE OPEN ACCESS Dynamic Modelling of Hybrid System for Efficient Power Transfer under Different Condition Kiran Kumar Nagda, Prof. R. R. Joshi (Electrical Engineering department, Collage of

More information

BIDIRECTIONAL FULL-BRIDGE DC-DC CONVERTER WITH FLYBACK SNUBBER FOR PHOTOVOLTAIC APPLICATIONS

BIDIRECTIONAL FULL-BRIDGE DC-DC CONVERTER WITH FLYBACK SNUBBER FOR PHOTOVOLTAIC APPLICATIONS INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET) Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14) ISSN 0976 6545(Print) ISSN 0976

More information

Fuzzy based STATCOM Controller for Grid connected wind Farms with Fixed Speed Induction Generators

Fuzzy based STATCOM Controller for Grid connected wind Farms with Fixed Speed Induction Generators Fuzzy based STATCOM Controller for Grid connected wind Farms with Fixed Speed Induction Generators Abstract: G. Thrisandhya M.Tech Student, (Electrical Power systems), Electrical and Electronics Department,

More information

Design and Simulation of Grid Connected PV System

Design and Simulation of Grid Connected PV System Design and Simulation of Grid Connected PV System Vipul C.Rajyaguru Asst. Prof. I.C. Department, Govt. Engg. College Rajkot, Gujarat, India Abstract: In this paper, a MATLAB based simulation of Grid connected

More information

A ZVS Interleaved Boost AC/DC Converter Using Super Capacitor Power for Hybrid Electrical Vehicles

A ZVS Interleaved Boost AC/DC Converter Using Super Capacitor Power for Hybrid Electrical Vehicles Vol. 3, Issue. 5, Sep - Oct. 2013 Pp-2786-2791 Issn: 2249-6645 A ZVS Interleaved Boost AC/DC Converter Using Super Capacitor Power for Hybrid Electrical Vehicles G. Rambabu 1, G. Jyothi 2 *(PG Scholar,

More information

A Novel Hybrid Smart Grid- PV-FC V2G Battery Charging Scheme

A Novel Hybrid Smart Grid- PV-FC V2G Battery Charging Scheme A Novel Hybrid Smart Grid- PV-FC V2G Battery Charging Scheme By E. Elbakush* A. M. Sharaf** *University of New Brunswick **SHARAF Energy Systems Inc. Contents Abstract Introduction System Configuration

More information

FOUR SWITCH THREE PHASE BRUSHLESS DC MOTOR DRIVE FOR HYBRID VEHICLES

FOUR SWITCH THREE PHASE BRUSHLESS DC MOTOR DRIVE FOR HYBRID VEHICLES INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET) Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14) ISSN 0976 6545(Print) ISSN 0976

More information

EFFICIENT GRID CONNECTED INVERTER TO OVERCOME THE LOAD DISTURBANCE IN HYBRID ENERGY STORAGE SYSTEM

EFFICIENT GRID CONNECTED INVERTER TO OVERCOME THE LOAD DISTURBANCE IN HYBRID ENERGY STORAGE SYSTEM ISSN: 2349-2503 EFFICIENT GRID CONNECTED INVERTER TO OVERCOME THE LOD DISTURBNCE IN HYBRID ENERGY STORGE SYSTEM T.Thiruppathi 1 S.ndal 2 M.Varatharaj 3 1 (UG Scholar of EEE, Christ the king engg college,

More information

Control Application of PV Solar Farm as PV- STATCOM for Reactive Power Compensation during Day and Night in a Transmission Network

Control Application of PV Solar Farm as PV- STATCOM for Reactive Power Compensation during Day and Night in a Transmission Network Control Application of PV Solar Farm as PV- STATCOM for Reactive Power Compensation during Day and Night in a Transmission Network 1 Kishor M. K, 2 T. R. Narasimhe Gowda, 3 R. D. Sathyanarayana Rao, 4

More information

IJSER. 1. Introduction. 2. Power flow of Doubly fed Induction Generator (DFIG) K. Srinivasa Rao 1 G. Kamalaker 2

IJSER. 1. Introduction. 2. Power flow of Doubly fed Induction Generator (DFIG) K. Srinivasa Rao 1 G. Kamalaker 2 International Journal of Scientific & Engineering Research, Volume 6, Issue 5, May-2015 798 Hybrid Protection to Enhance the LVRT Capability of a Wind Turbine Based DFIG K. Srinivasa Rao 1 G. Kamalaker

More information

A DIGITAL CONTROLLING SCHEME OF A THREE PHASE BLDM DRIVE FOR FOUR QUADRANT OPERATION. Sindhu BM* 1

A DIGITAL CONTROLLING SCHEME OF A THREE PHASE BLDM DRIVE FOR FOUR QUADRANT OPERATION. Sindhu BM* 1 ISSN 2277-2685 IJESR/Dec. 2015/ Vol-5/Issue-12/1456-1460 Sindhu BM / International Journal of Engineering & Science Research A DIGITAL CONTROLLING SCHEME OF A THREE PHASE BLDM DRIVE FOR FOUR QUADRANT OPERATION

More information

Analysis of high frequency ac link PV inverter

Analysis of high frequency ac link PV inverter Analysis of high frequency ac link PV inverter K.Vinay Kumar M Tech Assistant Professor SVS INSTITUTE OF TECHNOLOGY (SVSIT) WARANGAL T.s, India, JNTU,HYD Durgam Kumaraswamy Phd(Parsuing) ASSOCIATE PROFESSOR

More information

ADVANCED POWER CONTROL TECHNIQUES FOR HYBRID WIND-POWER GENERATION SYSTEM USED IN STANDALONE APPLICATION

ADVANCED POWER CONTROL TECHNIQUES FOR HYBRID WIND-POWER GENERATION SYSTEM USED IN STANDALONE APPLICATION ADVANCED POWER CONTROL TECHNIQUES FOR HYBRID WIND-POWER GENERATION SYSTEM USED IN STANDALONE APPLICATION T.Rangarajulu 1, M.Tamil Selvi 2, Professor 1,PG Student 2 Karpaga Vinayaga College of Engineering

More information

Power System Stability Analysis on System Connected to Wind Power Generation with Solid State Fault Current Limiter

Power System Stability Analysis on System Connected to Wind Power Generation with Solid State Fault Current Limiter IJSTE - International Journal of Science Technology & Engineering Volume 2 Issue 2 August 2015 ISSN (online): 2349-784X Power System Stability Analysis on System Connected to Wind Power Generation with

More information

A Double Input Buck Boost Converter for Wind Energy System with Power.. S.Kamalakkannan et al., International Journal of Power Control and Computation(IJPCSC) Vol 7. No.2 2015 Pp.54-60 gopalax Journals,

More information

Protection of Power Electronic Multi Converter Systems in AC and DC Applications

Protection of Power Electronic Multi Converter Systems in AC and DC Applications Protection of Power Electronic Multi Converter Systems in AC and DC Applications Prof. Norbert Grass Technische Hochschule Nürnberg, Institute for Power Electronic Systems, Nuremberg, Germany, Norbert.Grass@th-nuernberg.de

More information

Increasing the Battery Life of the PMSG Wind Turbine by Improving Performance of the Hybrid Energy Storage System

Increasing the Battery Life of the PMSG Wind Turbine by Improving Performance of the Hybrid Energy Storage System IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, PP 36-41 www.iosrjournals.org Increasing the Battery Life of the PMSG Wind Turbine by Improving Performance

More information

Reactive Power Compensation at Load Side Using Electric Spring

Reactive Power Compensation at Load Side Using Electric Spring IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331 PP 28-33 www.iosrjournals.org Reactive Power Compensation at Load Side Using Electric Spring Neethu

More information

Laboratory Tests, Modeling and the Study of a Small Doubly-Fed Induction Generator (DFIG) in Autonomous and Grid-Connected Scenarios

Laboratory Tests, Modeling and the Study of a Small Doubly-Fed Induction Generator (DFIG) in Autonomous and Grid-Connected Scenarios Trivent Publishing The Authors, 2016 Available online at http://trivent-publishing.eu/ Engineering and Industry Series Volume Power Systems, Energy Markets and Renewable Energy Sources in South-Eastern

More information

A NOVEL MULTIPHASE BIDIRECTIONAL FLY-BACK CONVERTER TOPOLOGY IS APPLIED TO INDUCTION MOTOR DRIVE

A NOVEL MULTIPHASE BIDIRECTIONAL FLY-BACK CONVERTER TOPOLOGY IS APPLIED TO INDUCTION MOTOR DRIVE A NOVEL MULTIPHASE BIDIRECTIONAL FLY-BACK CONVERTER TOPOLOGY IS APPLIED TO INDUCTION MOTOR DRIVE M.RAMA MOHANA RAO 1 & CH.RAMBABU 2 1,2 Department of Electrical and Electronics Engineering, Sri Vasavi

More information

Wind-Turbine Asynchronous Generator Synchronous Condenser with Excitation in Isolated Network

Wind-Turbine Asynchronous Generator Synchronous Condenser with Excitation in Isolated Network Wind-Turbine Asynchronous Generator Synchronous Condenser with Excitation in Isolated Network Saleem Malik 1 Dr.Akbar Khan 2 1PG Scholar, Department of EEE, Nimra Institute of Science and Technology, Vijayawada,

More information

Rotor Position Detection of CPPM Belt Starter Generator with Trapezoidal Back EMF using Six Hall Sensors

Rotor Position Detection of CPPM Belt Starter Generator with Trapezoidal Back EMF using Six Hall Sensors Journal of Magnetics 21(2), 173-178 (2016) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2016.21.2.173 Rotor Position Detection of CPPM Belt Starter Generator with Trapezoidal

More information

Fuzzy Logic Control Based MIMO DC-DC Boost Converter for Electric Vehicle Application Ans Jose 1 Absal Nabi 2 Jubin Eldho Paul 3

Fuzzy Logic Control Based MIMO DC-DC Boost Converter for Electric Vehicle Application Ans Jose 1 Absal Nabi 2 Jubin Eldho Paul 3 IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 10, 2015 ISSN (online): 2321-0613 Fuzzy Logic Control Based MIMO DC-DC Boost Converter for Electric Vehicle Application

More information

Design of Integrated Power Module for Electric Scooter

Design of Integrated Power Module for Electric Scooter EVS27 Barcelona, Spain, November 17-20, 2013 Design of Integrated Power Module for Electric Scooter Shin-Hung Chang 1, Jian-Feng Tsai, Bo-Tseng Sung, Chun-Chen Lin 1 Mechanical and Systems Research Laboratories,

More information

Load Frequency Control of a Two Area Power System with Electric Vehicle and PI Controller

Load Frequency Control of a Two Area Power System with Electric Vehicle and PI Controller Load Frequency Control of a Two Area Power System with Electric Vehicle and PI Controller Vidya S 1, Dr. Vinod Pottakulath 2, Labeeb M 3 P.G. Student, Department of Electrical and Electronics Engineering,

More information

Dual-Rail Domino Logic Circuits with PVT Variations in VDSM Technology

Dual-Rail Domino Logic Circuits with PVT Variations in VDSM Technology Dual-Rail Domino Logic Circuits with PVT Variations in VDSM Technology C. H. Balaji 1, E. V. Kishore 2, A. Ramakrishna 3 1 Student, Electronics and Communication Engineering, K L University, Vijayawada,

More information

DESIGN AND ANALYSIS OF CONVERTER FED BRUSHLESS DC (BLDC) MOTOR

DESIGN AND ANALYSIS OF CONVERTER FED BRUSHLESS DC (BLDC) MOTOR DESIGN AND ANALYSIS OF CONVERTER FED BRUSHLESS DC (BLDC) MOTOR 1 VEDA M, 2 JAYAKUMAR N 1 PG Student, 2 Assistant Professor, Department of Electrical Engineering, The oxford college of engineering, Bangalore,

More information

A HIGH EFFICIENCY BUCK-BOOST CONVERTER WITH REDUCED SWITCHING LOSSES

A HIGH EFFICIENCY BUCK-BOOST CONVERTER WITH REDUCED SWITCHING LOSSES Int. J. Elec&Electr.Eng&Telecoms. 2015 Mayola Miranda and Pinto Pius A J, 2015 Research Paper ISSN 2319 2518 www.ijeetc.com Special Issue, Vol. 1, No. 1, March 2015 National Level Technical Conference

More information

Design and Analysis of a Grid Connected Renewable Home Energy System

Design and Analysis of a Grid Connected Renewable Home Energy System Design and Analysis of a Grid Connected Renewable Home Energy System Rani T R Electrical & Electronics Department Government Engineering college Idukki Thrissur, India Raji Krishna Electrical & Electronics

More information

ENHANCEMENT OF ROTOR ANGLE STABILITY OF POWER SYSTEM BY CONTROLLING RSC OF DFIG

ENHANCEMENT OF ROTOR ANGLE STABILITY OF POWER SYSTEM BY CONTROLLING RSC OF DFIG ENHANCEMENT OF ROTOR ANGLE STABILITY OF POWER SYSTEM BY CONTROLLING RSC OF DFIG C.Nikhitha 1, C.Prasanth Sai 2, Dr.M.Vijaya Kumar 3 1 PG Student, Department of EEE, JNTUCE Anantapur, Andhra Pradesh, India.

More information

A Reduced switch count Soft-Switching Current-Fed Full-Bridge Isolated DC/DC Converter for Fuel Cell Vehicles

A Reduced switch count Soft-Switching Current-Fed Full-Bridge Isolated DC/DC Converter for Fuel Cell Vehicles A Reduced switch count Soft-Switching Current-Fed Full-Bridge Isolated DC/DC Converter for Fuel Cell Vehicles Julakanti Mounika M.Tech Student, Department of PEED, HITAM Engineering College. Abstract:

More information

DUAL BRIDGE RECTIFIER FOR PMSG VARIABLE SPEED WIND ENERGY CONVERSION SYSTEMS

DUAL BRIDGE RECTIFIER FOR PMSG VARIABLE SPEED WIND ENERGY CONVERSION SYSTEMS DUAL BRIDGE RECTIFIER FOR PMSG VARIABLE SPEED WIND ENERGY CONVERSION SYSTEMS Ch. Neelima, Dr. P. Mallikarjuna Rao 1PG scholar, Dept of Electrical Engineering, A.U. College of Engineering (A), Andhra Pradesh,

More information

A Two Stage TCDIC with Five-Level Inverter for Stand-Alone and Grid Connected Applications

A Two Stage TCDIC with Five-Level Inverter for Stand-Alone and Grid Connected Applications A Two Stage TCDIC with Five-Level Inverter for Stand-Alone and Grid Connected Applications Jagruthi Petrum(Regd No:14NR1D5409) M-tech Student Scholar Department of Electrical & Electronics Engineering,

More information