EAGL 2000 & EAGL 3000S Laser Levels
|
|
- Marvin Curtis Higgins
- 5 years ago
- Views:
Transcription
1 EAGL 2000 & EAGL 3000S Laser Levels Owner s Manual
2 GENERAL INFORMATION Thank you for buying the EAGL laser. Although it is very simple to use, we recommend that you read this manual before operating the laser. Specifications Operating range EAGL 2000: 2,000 ft. (600m) diameter EAGL 3000S: 3,000 ft. (900m) diameter Self-leveling range ± 4 (± 7%) Accuracy Better than 100 (± 4mm/100m) ± 8 arc seconds H.I. Alert Windy mode Matching slope Rotation speed Laser shut-off; user chooses mode as desired Reduces sensitivity; does not change accuracy EAGL 3000S only: ± 6% manual slope in X axis; Y axis is self-leveling 600 rpm Beam type/output Infrared diode; 785nm; 1.0mW; Class 1 Power sources Battery life Mounting base Water resistance (1) 4 D size alkaline battery pack (2) optional NiCd rechargeable battery pack (3) AC charger with optional NiCd battery pack Approximately 100 hours (alkaline) 40 hours (NiCd) 5/8 x 11 flat or domed IP55 Operating temperature 14º to 122º F (-10º to 50º C) Storage temperature -4 to 140 F (-20 to 60 C) Dimensions 8 h x 6.5 w x 6 d (20 x 16 x 15cm) 5 lbs. (2.3kg) 2
3 Overview of Laser & Keypad Alignment grove (3000S only) X axis calibration port Y axis calibration port Battery compartment COMPLIES WITH 21CFR AND EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JULY 26, CLASS 1 LASER PRODUCT Safety label on side of laser EAGL 2000 Keypad EAGL 3000S Keypad Windy mode H.I. Alert Windy mode H.I. Alert On/Off Match slope in X axis Positive slope On/Off Negative slope Battery indicator Level indicator Battery indicator Level indicator 3
4 OPERATION Setup The laser mounts to any 5/8 x 11 tripod (flathead or domed) or can rest on any stable flat surface (floor, bricks, etc.). Position tripod, attach laser, then adjust tripod until rough leveled (within ±4 self-leveling range). Turning on the Laser Press the on/off key to power-up the laser. The unit s self-checking system will start automatically. The LEDs will flash if anything goes wrong during the self check procedure. Battery LED should be green; if batteries are low, LED will be red. Leveling When laser is turned on, the level indicator will flash red until unit is level. If it fails to self-level within 90 seconds, the red LED will be constantly lit. Re-adjust tripod to bring into self-leveling range. When unit is level, the rotor head will begin spinning (600 rpm). Level Alert If laser is disturbed, the level alert system will stop head rotation. Unless disturbed out of self-leveling range ( ±4 ), unit will self-level and return to operation automatically. Always recheck beam height against benchmark when releveling is required. Windy Mode Windy mode allows continuous operation during high winds, slight vibrations, and shocks on the job site. It prevents the laser from constantly re-leveling from high vibration. Selection of Windy mode lowers the sensitivity but does not decrease the accuracy. To use this mode, press the Windy key. H.I. Alert H.I. (height of instrument) alert stops the laser automatically if it s disturbed, preventing inaccurate readings. It functions only when selected. To activate this safeguard, press the H.I. key after the laser has leveled. The H.I. LED blinks slowly for about 30 seconds before turning solid green. If laser is disturbed, the head will stop rotating, the green H.I. LED will flash rapidly, and the red level indicator will come on. Press the H.I. key to turn off the alert, allowing the laser to level itself. 4
5 After it has releveled, check if the beam elevation has changed from its original benchmark position. Press the H.I. key again to return to H.I. alert. Windy mode can be on on or off when H.I alert is used. Matching Slope (EAGL 3000S only) The EAGL 3000S can be used to match a single slope in X axis, up to 6% positive or 6% negative slope. While the X axis is in manual mode, the Y axis continues to be self-leveling. Position laser so the +X axis faces direction of the slope. (The laser s battery compartment will be toward the slope, with handle facing away.) Sight down the alignment groove on top of the laser to roughly aim laser to the grade reference. Turn the laser on and allow it to self-level. Press both Manual keys simultaneously. The two green LEDs on the keys will be constantly lit, indicating you re in the grade mode. TOP VIEW X Axis FRONT Use the right key to match a positive slope; the left key for a negative slope. While slope is being entered, the LED on that key will flash. Avoid moving laser when pushing the keys, as this may Negative slope Positive slope cause rotation to stop; grade cannot be entered if laser stops rotating. Press both keys again at the same time to return to automatic mode (no slope). Checking Your Laser The laser is a precision instrument and it is important that you keep it calibrated and in proper condition. The accuracy of your work is completely your responsibility and you should check your instrument daily, or at a minimum before beginning each job, and definitely after the instrument has taken a sharp jolt or been dropped, or temperature changes greater than 50 degrees F (28 degrees C) have occurred. See simple instructions to check calibration in this manual. + X Power Sources The laser can be operated from 4 D-size alkaline batteries or the optional NiCd rechargeable battery pack (charge before first use). The NiCd battery pack can also be charged while working. If electricity is available on the job site, simply plug in the charger and keep working. 5
6 BATTERY PACK To replace the alkaline batteries, or to charge the NiCd pack, first remove the battery pack. The NiCd pack must be charged before first use. Removing the Battery Pack 1. Press the battery unlock button -- see (1) in the diagram at right. 2. Supporting the battery, press battery release (2) to remove it. A) Battery Replacement 1. Raise the battery cover release to remove the battery cover. 2. Insert 4 D batteries. The insertion direction of the batteries is indicated on the battery pack. 3. Attach the battery cover, inserting the guide lips into the guide slots. B) Recharging (optional NiCd pack) 1. Remove charging connector cap on the battery pack and plug in the charger. 2. Plug charger into electrical outlet. A red light on the charger indicates it s charging. 3. When the red light blinks (lights on for 6 seconds, off for 20 seconds), the charging is finished. Charging time is about 7.5 hours. The unit can be charged while working. For optimum life of the battery, it s recommended to charge the battery after fully discharged. To assure battery life, do not charge over 20 hours. C) Installing the Battery Pack 1. Fit the guide posts of the battery into the guide slots of laser. 2. Attach the battery to the laser by pressing the top of the battery against the laser until a click is heard. 6 Battery Unlock Button Battery Release Battery Cover Battery Cover Release Guide Lip Guide Slot Guide Post Guide Slot
7 CALIBRATION Calibration should be checked regularly. For convenience you should establish a range for routine and quick checks. Your AGL dealer can assist you in setting up one. Allow at least 15 minutes of warm-up time before checking or adjusting calibration. Steps 1-7 deal with checking calibration. If adjustment is needed, Steps 8-12 explain the procedure. Follow the instructions carefully. Checking Calibration 1. Select a level range at least 100 ft. (30 m) long. Set up the laser on a flat surface or tripod. Approximately 100 ft. (30 m) away, erect a vertical pole or rod. 2. Position laser so one axis is aligned toward pole at end of range. 3. Turn laser on and allow to level. 4. Using a detector, mark elevation of beam at pole (this is mark A). 5. Rotate laser 180 so the axis is again aligned with pole but in opposite direction. Use detector again to mark elevation of beam on pole (mark B). 6. If marks A and B are within 1/8 (2.5 mm), calibration is correct. 7. Repeat the above procedure for the other axis. If marks are more than 1/8 (2.5 mm) apart, proceed to Step 8 for calibration adjustment. Calibration Adjustment 8. Make new A and B marks (repeat Steps 2-7). Make a third mark halfway between the new A and B. Call this mark C. This is the correct beam center. 9. The calibration port for each axis is located on the top front of the laser (see photo in Laser Overview). Choose the port matching the axis you are calibrating. Open only one cover at a time to avoid adjusting the wrong axis. 10. Using a small screwdriver, carefully turn the exposed calibration port until beam is centered at mark C. Make adjustments in small, careful increments. After each adjustment, check beam movement at Top View the pole. 11. Double check the axis. Rotate the laser 180 X Axis and again check the beam. Beam should now strike within 1/16 (1.5 mm)of mark C. If not, repeat Steps 8-10, adjusting as needed until axis is calibrated. 12. Repeat Steps 2-11 for the other axis. Calibration is complete when mark C is the same for both axes in both directions. FRONT If you experience difficulty or have questions regarding this procedure, call your AGL dealer or the factory. Our toll-free number is Outside the continental U.S., call Y Axis 7
8 LS100 DETECTOR For Grade Rod or Handheld Applications FRONT Choice of accuracy Choice of sound level On/Off LEDs: To turn on or off, press Accuracy and Sound level keys at the same time LCD (front) Detection window Sound output Fast beep: Too low Continuous: On-grade Slow beep: Too high BACK 2 (50 mm) Tab slot locks clamp in place LCD (rear) Offset notch for transferring reference marks Clamp slots Compartment for 2 AA batteries. Open with coin; follow polarity indications inside. 8
9 LCD DISPLAY Accuracy Sound Loud Normal Fine Medium Wide Grade indication arrows (see 11 channels below) High On-grade Low No horn: Mute Indicates that LEDs are on OK Initial warning Change batteries Battery status LEDs Grade can also be indicated by LEDs. Ideal for use in low light or above eye level, or for long range jobs like slope match. Press the top two keys at the same time to get the 5-channel display. LEDs are muli-color and solid or blinking. Red Green Blue High Near grade high On-grade Near Low grade low 9
10 Using the Detector 1. Press On/Off key to turn on the detector. 2. Press top key to select the accuracy (deadband) and middle key to select sound level. (The detector retains in memory the last settings used.) 3. Turn the detection window towards the laser beam, and move the detector up or down according to the information given on the LCD display. A down arrow indicates you must move the detector down to reach the laser reference; an up arrow, move it up. When a horizontal line appears on the display, the detector is at the same level as the laser beam. 4. To turn on the LED grade indicators, press the accuracy and sound level keys at the same time. 5. Press the On/Off key to turn the detector off. It will automatically shut off after 30 minutes if not used. 6. Keep the detection window and LCDs clean, using a soft cloth and glass cleaner or mild soap and water. Do not wipe with a dry cloth, which can scratch the windows. Detector may be submerged under water or sprayed with a low pressure hose. Side View Securing the clamp to the detector 1. Align the two dovetails of the clamp (1) to the slots on the back of the detector. Slide down; you should hear a click. 2. Turn clamping screw (4) counterclockwise to open the clamp s jaws; turn clockwise to tighten onto a rod. 3. The top of the bar (3) is aligned with the detector s on-grade location and marking notches. 4. To remove clamp from detector, press thumb release tab (2) and slide clamp upward. Using clamp on oval rods The traveling jaw (5) is reversible, and has a slant face for use on oval or round rods. To change, remove screw with a flathead screwdriver, flip the face over, and replace screw Rectangular Rods Top View Reversible jaw Bubble vial to plumb rod Oval/Round Rods
11 Detector Specifications Working radius Beam reception range ± 45 Beam window height Detection accuracy Display channels Power supply Battery life Up to 1,500 ft. (450m) 2 (50 mm) Fine: ~ ±1/32 (± 1 mm) Medium: ~ ±1/16 (± 2 mm) Wide: ~ ±1/8 (± 3 mm) 11 on LCD; 5 with LEDs 2 AA alkaline batteries 70+ hours with LEDs off 50+ hours with LEDs on Operating temperature -4 F to 140 F (-20 C to 60 C) Storage temperature -40 F to 158 F (-40 C to 70 C) Automatic shut-off Strobe rejection Environmental Weight (with batteries) Dimensions (HxWxD) *Specifications subject to change without notice. 30 minutes / no use Detector does not respond to strobe Waterproof (IP67) 1 lb. with clamp (0.45 kg) 6.4 x 2.9 x 1.14 in. (163 x 74 x 29 mm) AGL Limited Warranty EXPRESS WARRANTY FOR HARDWARE. AGL Corporation ( AGL ) warrants to the original end user ( Customer ) that this Product will be free from defects in workmanship and materials, under normal use, for two (2) years and non-agl-manufactured products for which ninety (90) days shall apply, unless such warranty period has been extended by AGL, and provided any and all operating and maintenance instructions are strictly respected, in particular in case of extreme and/or continuous applications/use of the Product. The warranty period begins on the proved purchase date, or if applicable, date of delivery or date of acceptance report. AGL s sole obligation under this express warranty shall be, at AGL s sole option and expense, to replace or repair the Product or part, or refund the purchase price paid for the Product. AGL warrants any repaired or replaced Product or part for a period of ninety (90) days from shipment, or through the end of the original warranty, whichever is longer. All Products or parts that are replaced become the property of AGL. This express warranty does neither cover consumables, such as batteries, bulbs and fuses, nor third party products. OBTAINING WARRANTY SERVICE. Customer must contact an authorized service center of AGL or AGL s Service Center within the applicable warranty period to obtain warranty service authorization. Dated proof of original purchase from AGL s authorized distributor and a description of the defect will be required. AGL is not responsible for Products or parts received without a warranty service authorization. Repaired or replacement Products will be shipped to Customer at AGL s expense. The repaired product or part will be shipped as soon as reasonably possible. AGL shall not be responsible for any damages occurring during such shipment. For Products forming part of a fixed installation, such place of performance shall be the site of such installation and AGL shall have the right to charge for additional costs for such services under warranty if the site of the Product is other than where the Product was originally shipped or installed. CONTINUED ON BACK PAGE. 11
12 CONTINUED FROM PAGE 11 WARRANTY EXCLUSIVE. Customer s sole remedy for breach of the warranty shall be the express warranty. The foregoing warranty is exclusive and is in lieu of all other warranties, terms, or conditions, express or implied, either in fact or by operation of law, statutory or otherwise, including warranties, terms or conditions of merchantability, fitness for a particular purpose, satisfactory quality and non-infringement, all of which are expressly disclaimed. AGL shall not be liable if the alleged defect or malfunction was caused by Customer s or any other person s misuse, neglect, improper installation, unauthorized attempts to open, repair or modify the Product, inadequate maintenance, disregard of operating instructions, excessive load or stress, normal wear and tear, or any other cause beyond the range of its intended use, by accident, fire, or other hazards, or other cause not due or attributable to AGL. This warranty does not cover physical damage to the Product or malfunctions resulting from the use of the Product in conjunction with any sort of ancillary or peripheral equipment and AGL determines that there is no fault with the Product itself. LIMITATION OF LIABILITY. AGL also excludes any liability, whether based on contract or tort (including negligence), for incidental, consequential, indirect, special, or punitive damages of any kind, or costs of procurement of substitute products by customer, or for the loss of revenue or profits, loss of business, loss of information or data, or other information or financial loss arising out of or in consequence with the sale, installation, maintenance, use, performance, failure, or interruption of this product, even if AGL or its distributors have been advised of the possibility of such damages, and limits its liability to replacement, repair, or refund of the purchase price paid, at AGL s option. This limitation of liability for damages will not be affected if any remedy provided herein shall fail of its essential purpose. DISCLAIMER. Should a court of jurisdiction not allow the entire exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to Customers, or the limitation of liability for personal injury, such implied warranties and such liabilities will be limited to the duration of the applicable express warranty. With this Limited Warranty, AGL grants Customer specific legal rights which do not restrict any statutory consumer rights. This Limited Warranty shall be governed by the laws of Arkansas, USA Redmond Rd., Jacksonville, AR sales@agl-lasers.com Toll Free: Phone: Fax: Specifications subject to change without notice. AM /2007 Printed in USA
EAGL 1-Touch Laser Level
EAGL 1-Touch Laser Level Owner s Manual GENERAL INFORMATION Thank you for buying the EAGL 1-Touch laser. Although it is very simple to use, we recommend that you read this manual before operating the laser.
More informationOPERATING MANUAL PLS HLE 1000 PACIFIC LASER SYSTEMS. The Professional Standard
OPERATING MANUAL PLS HLE 1000 PACIFIC LASER SYSTEMS The Professional Standard TABLE OF CONTENTS Introduction...Page 1 Safety Information...Page 2 Batteries...Page 3 Keypad...Page 4 Functions...Page 5 Applications...Page
More informationOPERATING MANUAL PLS HVR 505
OPERATING MANUAL PLS HVR 505 PACIFIC LASER SYSTEMS The Professional Standard TABLE OF CONTENTS Introduction...Page 1 Safety Information...Page 2 Batteries...Page 3 Keypad...Page 4 Operation...Page 5 Functions...Page
More informationOPERATING MANUAL PLS HVR 505 PACIFIC LASER SYSTEM S. The Professional Standard
OPERATING MANUAL PLS HVR 505 PACIFIC LASER SYSTEM S The Professional Standard TABLE OF CONTENTS INTRODUCTION Introduction...Page 1 Safety Information...Page 2 Batteries...Page 3 Keypad...Page 4 Operation...Page
More informationLaser Receiver Model MCR3. Operator's Manual
Laser Receiver Model MCR3 Operator's Manual Thank you for purchasing a Futtura product. Your receiver is a premium quality tool that has been designed and manufactured to provide years of precise and reliable
More informationUsers Guide for Ac-sync
Problem solved. Users Guide for Ac-sync Thank you for choosing Anywhere Cart! The AC-SYNC is designed to sync, charge and store 1-36 ipads or tablets. Adjustable device divider bays allow fitment of any
More information031266_Umschlag_HV_301.qxd :36 Uhr Seite 1 HV301
HV301 www.trimble.com www.trimble.com TABLE OF CONTENTS GB FOR YOUR SAFETY 12 Important Information 12 COMPONENTS 13 SETTING TO WORK 13 Rotation mode 13 Pointing mode 13 Line/scanning mode 14 Self-leveling
More informationSUNTURA HD SOLAR TRACKER
WindyNation SUNTURA HD SOLAR TRACKER SOT-TRKS-NFHD User s Manual Page 1 of 11 WindyNation 08/09/2012 Table of Contents 1! Introduction... 3! 1.1! Limited Warranty... 3! 1.2! Restrictions... 3! 1.3! Warranty
More informationSUNTURA SOLAR TRACKER
WindyNation SUNTURA SOLAR TRACKER SOT-TRKS-NF User s Manual Page 1 of 10 WindyNation 08/09/2012 Table of Contents 1 Introduction... 3 1.1 Limited Warranty... 3 1.2 Restrictions... 3 1.3 Warranty Claims
More informationGradeLight Pipe Laser. Owner s Manual
GradeLight 2700 Pipe Laser Owner s Manual AGL Construction Lasers & Machine Control Systems 2202 Redmond Rd., Jacksonville, AR 72076 sales@agl-lasers.com www.agl-lasers.com Toll Free: 800.643.9696 Phone:
More informationPVI 1800/PVI Residential/Commercial Grid-Tied Photovoltaic Inverter WARRANTY MANUAL. Subject to Change REV , Solectria Renewables
PVI 1800/PVI 2500 WARRANTY MANUAL Residential/Commercial Grid-Tied Photovoltaic Inverter 2009, Solectria Renewables Subject to Change REV 10.09 1 Product Warranty & RMA Policy 1.1 Warranty Policy The Solectria
More informationDUSTTRAK AEROSOL MONITOR SOLAR POWER KIT MODEL
DUSTTRAK AEROSOL MONITOR SOLAR POWER KIT MODEL 854060 (USED FOR POWERING ENVIRONMENTAL ENCLOSURE MODELS MODELS 854030, 8535 AND 8537) OPERATION AND MAINTENANCE MANUAL P/N 6008416, REVISION C JUNE 2017
More informationWARRANTY POLICY. Grid-Tied Photovoltaic Inverters. Revision D. 2014, Solectria Renewables, LLC DOCIN
WARRANTY POLICY Revision D 2014, Solectria Renewables, LLC DOCIN-070360 1 Product Warranty & RMA Policy 1. Warranty Policy Warranty Registration: It is important to have updated information about the inverter
More informationInstallation and Operation Instructions Safety Director Arrow
Installation and Operation Instructions Safety Director Arrow! WARNING! Failure to install or use this product according to manufacturers recommendations may result in property damage, serious bodily/personal
More informationPLS SLD. Laser Detector PACIFIC LASER SYSTEMS. For use with your PLS pulsed laser alignment tool. The Professional Standard
PLS SLD Laser Detector For use with your PLS pulsed laser alignment tool. 9 PACIFIC LASER SYSTEMS The Professional Standard GENERAL DESCRIPTION IMPORTANT: YOUR PLS SLD DETECTOR IS DESIGNED FOR USE WITH
More informationTABLE OF CONTENTS 10.0 LIMITED WARRANTY
10.0 LIMITED WARRANTY ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the original purchaser that this product is of merchantable quality and confirms in kind and quality with the descriptions
More informationInstallation Power Management Unit Battery Cables and Battery Harness
Installation Power Management Unit Battery Cables and Battery Harness Important Safety Messages SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation
More informationPVI 60KW, PVI 82KW, PVI 95KW
PVI 60KW PVI 82KW PVI 95KW WARRANTY MANUAL Commercial, Grid-Tied Photovoltaic Inverters 2008, Solectria Renewables LLC Subject to Change DOC-020099 rev 024 1 1 Product Warranty & RMA Policy Warranty Policy
More informationInstallation Instructions Winch Quick Connect Kit Part # (8 ) Part # (24 )
Please read instructions entirely before installing/using this part. Parts Included (Part# 35220) Qty Parts Included (Part# 35210) Qty 3 Winch Quick Connect Wire 1 3 Winch Quick Connect Wire 1 8 Quick
More informationCRD610 Automatic Fitting Inserter
CRD610 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 1.2 LAST EDITED 12.12.2018 cleanroomdevices.com 1 Table of Contents Title Page. 1 Table of Contents...2 1.0 General Product & Safety Information....3
More informationDo not install and/or operate this safety product unless you have read and understand the safety information contained
Installation and Operation Instructions ED3766 TRI Color Directional LED Available in various color combinations, the ED3766 Directional LED is a surface mount, tri-color warning light that is ideal for
More informationInstruction Manual for Globe Price Computing Scale Models GS30 and GS30T
Model GS30 Model #: Serial #: Model GS30T NTEP Approved Meets NIST Handbook 44 Criteria Legal for Trade Instruction Manual for Globe Price Computing Scale Models GS30 and GS30T For Service on Your Scale:
More informationInstruction Manual for Globe Price Computing Scale Models GS30 and GS30T
Model GS30 Model #: Serial #: Model GS30T NTEP Approved Meets NIST Handbook 44 Criteria Legal for Trade Instruction Manual for Globe Price Computing Scale Models GS30 and GS30T For Service on Your Scale:
More informationPOWER TILT ACCESSORY FUZE T50 STELLAR GL STELLAR LEAP OWNER S OPERATION AND MAINTENANCE MANUAL
POWER TILT ACCESSORY FUZE T50 STELLAR GL STELLAR LEAP OWNER S OPERATION AND MAINTENANCE MANUAL PAGE 2 WARNING Do not install, maintain or operate this equipment without first reading and understanding
More information2060F / 2062F / 2064F
Operation & Installation Guide 060F / 06F / 064F DIGITAL ANTI-THEFT SAFE MANUAL # M08-070-000 Index / Overview of Your Safe INDEX Overview of Your Safe...1 Initial Set Up... Programming a Personal Passcode...
More informationIAQ-CALC INDOOR AIR QUALITY METER MODEL 7515
IAQ-CALC INDOOR AIR QUALITY METER MODEL 7515 OPERATION AND SERVICE MANUAL P/N 1980571, REVISION D FEBRUARY 2016 Copyright TSI Incorporated / May 2007-2016 / All rights reserved. Address TSI Incorporated
More informationIntelligent Electronic Safe
Operation & Installation Guide 1036616 / 1036617 / 1036618 Intelligent Electronic Safe Please do not keep emergency keys in your safe! MANUAL # M08-0566-155041 Index / Proper Use of Your Safe INDEX Proper
More informationCRD600 Automatic Fitting Inserter
CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.3 LAST EDITED 12.07.2018 cleanroomdevices.com 1 Table of Contents Title Page.. 1 Table of Contents. 2 1.0 General Product & Safety Information...3
More informationGradeLight Pipe Laser
GradeLight 3000 Pipe Laser CONTENTS GENERAL INFORMATION... 2 Specifications... 2 Laser Overview... 3 POWER... 5 Charging... 5 Removing the Battery Pack and Using Alkaline Batteries... 5 OPERATION... 6
More informationMEX (55) QRO (442) Web Controls
Web Controls SINGLE AND DUAL ROTOR TENSION CONTROL BRAKES MODELS:,,,, AND INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS Read this manual carefully, making full use of its explanations and instructions.
More informationThermometer models / 00831A
Instruction Manual Thermometer models 00822 / 00831A CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries...
More information4-Hour. Rapid Charger. for AA/AAA NiMH & NiCd Rechargeable Batteries. Owner's Manual
4-Hour Rapid Charger for AA/AAA NiMH & NiCd Rechargeable Batteries Owner's Manual Thank you for purchasing the Watson 4-Hour Rapid Battery Charger. Be sure to read this manual and note the precautions
More informationOperation & Installation Guide 2074F / 2079F. Manual # M Digital Anti-Theft Drawer Safe. Manual # M
Operation & Installation Guide 07F / 079F Manual # M08-07-000 www.firstalert.com Digital Anti-Theft Drawer Safe Manual # M08-07-000 Index / Overview of Your Safe Index Overview of Your Safe Package contents
More informationWARNING. Laser light is extremely bright and can potentially cause permanent eye damage or interfere with critical operations if improperly used.
TG7630G / TG7630R TRUGLO, Inc. 525 International Parkway RICHARDSON, TEXAS 75081 MADE IN CHINA Green Laser: POWER OUTPUT
More informationwill result in death or serious injury. could result in death or serious injury. Indicates a hazardous situation which, if not avoided,
SAFETY SETUP OPERATION MAINTENANCE WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this
More informationModel 2008 I Battery Operated Irrigation Timer with 3/4 in. Anti-Siphon Valve
i n s t r u c t i o n m a n u a l Model 2008 I Battery Operated Irrigation Timer with 3/4 in. Anti-Siphon Valve Features Weekly or cyclical programming 4 start times per day in weekly program Irrigation
More informationOperation & Installation Guide 2087DF / 2092DF. Manual # M DIGITAL WATERPROOF. Manual # M
Operation & Installation Guide DF / DF Manual M-- www.firstalert.com DIGITAL WATERPROOF FIRE Safe Manual M-- L--XZ Index Index Overview of Your Safe... Opening Your Safe for the First Time... Test Locking
More informationXLR-IR850 Long-Range Infrared Illuminator
XLR-IR850 Long-Range Infrared Illuminator USER MANUAL Description Armasight s extra long-range infrared illuminators provide greater, image-intensified viewing capabilities for operations in little to
More informationSAFETY AND CERTIFICATIONS
77-189 SAFETY AND CERTIFICATIONS Working safely with this instrument is possible only when the operating and safety information are read completely and the instructions contained therein are strictly followed.
More informationPower Controller IMPORTANT INFORMATION. What s In the Box? Assembly, Operation, & Maintenance
Power Controller Assembly, Operation, & Maintenance Congratulations on your purchase, and thank you for selecting the Power Controller from Blichmann Engineering. We are confident that it will provide
More informationLifeGuardLift. LifeGuard Power Lift Model #100287A OWNERS MANUAL. Rev: 2/14/11
LifeGuardLift OWNERS MANUAL LifeGuard Power Lift Model #100287A Rev: 2/14/11 Table of Contents 1. ASSEMBLY INSTRUCTIONS A. Lift Assembly B. Setup C. Disassembly 2. CONTROL SYSTEM A. Batteries B. Battery
More informationInstallation Instructions
Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual
More informationThank you for purchasing a 911EP GALAXY Light Bar! Every light bar is carefully inspected for defects prior to shipment.
OWNER S MANUAL Safety First Thank you for purchasing a 911EP GALAXY Light Bar! Every light bar is carefully inspected for defects prior to shipment. Questions or Concerns? 911EP wants to quickly resolve
More informationAIR VELOCITY METER ALNOR MODEL AVM410 AIRFLOW INSTRUMENTS MODEL TA410
AIR VELOCITY METER ALNOR MODEL AVM410 AIRFLOW INSTRUMENTS MODEL TA410 OPERATION AND SERVICE MANUAL P/N 1980575, REV F FEBRUARY 2016 Copyright TSI Incorporated / 2007-2016 / All rights reserved. Address
More informationCustomer Support
Portable auxiliary air tanks owner's Manual aux05 aux05a aux10 WWW.CALIFORNIAAIRTOOLS.COM Customer Support 1-866-409-4581 TAbLe OF CONTeNTS INTROduCTION IntroductIon Important Safety InStructIonS components
More informationModel:M5B/M5W/M5N. Installation Guide. Specifications Desktop Weight Capacity Keyboard Tray Weight Capacity Height Adjustable Range
Model:M5B/M5W/M5N Installation Guide Website: www.flexispot.com Tel: 1-855-421-2808 Specifications Desktop Weight Capacity Keyboard Tray Weight Capacity Height Adjustable Range 33 Ibs (15 KG) 4.4 Ibs (2
More informationThe function of this Dynamic Active Probe has divided into three preferences on the screen main Menus:
1.0 Introduction: This probe is designed to provide an additional help to automotive technicians in trouble shooting of electrical circuits problems in the car. Apart from using the normal multi tester,
More informationInstruction Manual. OEM Frameless Rear View Replacement Mirror Monitor with 7.2" Dual Display RVS Reverse With Confidence 1
Instruction Manual OEM Frameless Rear View Replacement Mirror Monitor with 7.2" Dual Display RVS-718-7 1 NOTE! Please read all of the installation instructions carefully before installing the product.
More informationCLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600AF Automatic Fitting Inserter With Auto Feed OPERATIONS MANUAL (Shown with optional alcohol dispenser) 1 VERSION 1.1 LAST EDITED
More informationINSTRUCTION MANUAL WARNING
INSTRUCTION MANUAL WARNING Please make sure you read the entire instruction manual to become familiar with the features of your aircraft before operating. Failure to operate this product correctly can
More informationGen 2 Electrically Released Motor Brake Module for EM-MBFB and EUM-MBFB
Gen 2 Electrically Released Motor Brake Module for EM-MBFB and EUM-MBFB P-273-8 819-0531 Installation Instructions Vented Enclosed Version Optional An Altra Industrial Motion Company Warner Electric s
More informationThermometer model 00826
Instruction Manual Thermometer model 00826 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries... 4 Set
More informationSubmersible Pond Pump with UV 800 Gallons Per Hour
Submersible Pond Pump with UV 800 Gallons Per Hour REMINDER CALL 1-888-755-6750 BEFORE RETURNING TO STORE. PACKAGE CONTENTS ITEM #PP800UV Questions, problems, missing parts? Before returning to your retailer,
More informationCLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.1 LAST EDITED 7.25.14 DOCUMENT NUMBER 001 cleanroomdevices.com 1 Table of
More information2087DF-BD / 2092DF-BD
Operation & Installation Guide DF-BD / DF-BD Manual M-- www.firstalert.com DIGITAL WATERPROOF FIRE Safe with Ready-Seal Manual M-- L--XZ Index / Overview of Your Safe Overview of Your Safe Index Overview
More information3.5mm Coaxial Calibration Kit
User Guide 3.5mm Coaxial Calibration Kit DC to 26.5 GHz Models: 8050CK10/11 8050CK20/21 8050-511 (A) 2/15 User Guide 3.5mm Coaxial Calibration Kit DC to 26.5 GHz Models: 8050CK10/11 8050CK20/21 2900 Inland
More informationCONTENTS. User Safety 2 Introduction and CX440 Accessories 3 CX440 Diagram 4 CX440 Keypad and Remote Control 5 Operating Instructions 6
CONTENTS User Safety 2 Introduction and CX440 Accessories 3 CX440 Diagram 4 CX440 Keypad and Remote Control 5 Operating Instructions 6 Batteries 6 Power and Horizontal Lines 7 Vertical Lines 8 Pulse (Outdoor)
More informationDigital echo-charge. Owner s Manual. Xantrex Digital echo-charge Battery Charger
Digital echo-charge Owner s Manual Xantrex Digital echo-charge Battery Charger INTRODUCTION The Xantrex Digital echo-charge is specially developed for charging an auxiliary battery with Freedom TM or Fleet
More informationUniversal 8-Bay Charger. for AA/AAA/C/D/9 NiMH & NiCd Rechargeable Batteries. Owner's Manual
Universal 8-Bay Charger for AA/AAA/C/D/9 NiMH & NiCd Rechargeable Batteries Owner's Manual Thank you for purchasing the Watson Universal 8-Bay Charger. Be sure to read this manual and note the precautions
More informationThermometer models 02023/02028/02053/02054
Instruction Manual Thermometer models 02023/02028/02053/02054 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Set the Time & Units...
More information2-Pack Indoor Simulated Dome Security Cameras
2-Pack Indoor Simulated Dome Security Cameras Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
More informationMQ4C-24/6485 WIRELESS INDOOR/OUTDOOR QUAD-COPTER
AGES 14+ MQ4C-24/6485 WIRELESS INDOOR/OUTDOOR QUAD-COPTER INSTRUCTION MANUAL PLEASE READ ALL INSTRUCTIONS CAREFULLY & RETAIN FOR FUTURE USE Welcome! Thank you for purchasing Wireless Indoor/Outdoor Quad-copter.
More informationDWS404 DWS524 DWS654 DWS684 DWS694. DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers
DWS404 DWS524 DWS654 DWS684 DWS694 DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers PREPARATION Safety Guidelines Thank you for purchasing the DWS Series car speakers. Although Dual has attempted
More informationOwners Manual. LifeGuard Power Lift Model # Rev. 2/1/13
Owners Manual LifeGuard Power Lift Model #100287 Rev. 2/1/13 Table of Contents 1. ASSEMBLY INSTRUCTIONS 3-5 A. Lift Assembly 3 B. Setup 3 1. Clinch Pin Location Drawings 4 2. Down Tube and Seat Assembly
More informationDAP-625S and DAP-875S
AIR CHAMP PRODUCTS DAP-625S and DAP-875S (i) FORM NO. L-20078-B-0501 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject
More informationInstallation Guide. Marine Filter SURT023M SURT024M
Installation Guide Marine SURT023M SURT024M suo0738a Product Description The APC by Schneider Electric Marine Application reduces the EMI (electro magnetic interference), produced by a connected that
More information12 Volt Utility Controller for 4, 6 or 8 Brakes No P
12 Volt Utility Controller for 4, 6 or 8 Brakes No. 1300-77 P-1379 819-0094 Installation Instructions Introduction The Warner Electric manually operated Utility Controller operates 4, 6, or 8 twelve-volt
More informationElectrically Released Motor Brake Module for EM-MBFB and EUM-MBFB Size 50, 100, 180
Electrically Released Motor Brake Module for EM-MBFB and EUM-MBFB Size 50, 100, 180 P-273-8-WE 819-0531 Installation Instructions Vented Enclosed Version Optional Warner Electric s MBFB series of Electrically
More informationWireless Thermometer model 00380
Instruction Manual Wireless Thermometer model 00380 CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries...
More informationIAQ-CALC TM Indoor Air Quality Meter
ENERGY AND COMFORT Indoor Air Quality IAQ-CALC TM Indoor Air Quality Meter Model 7515 Operation and Service Manual Copyright TSI Incorporated / May 2007 / All rights reserved. LIMITATION OF WARRANTY AND
More informationKIT CONSISTS OF: FEATURES. S-Digit mini
S-Digit mini FEATURES POWER On/Off switch ZERO Calibrate the unit (see instructions below) DEG/GRAD Set reading to degrees ( ) or percent (%) HOLD Current reading will be frozen by pressing HOLD. By pressing
More informationEND USER TERMS OF USE
END USER TERMS OF USE The following is the End Users Terms of Use as it currently appears in the Mobileye User Manual and Warranty information. This is here for your review and information; it is subject
More informationPLEASE ENSURE THE JUMP STARTER IS FULLY CHARGED PRIOR TO FIRST USE.
PLEASE ENSURE THE JUMP STARTER IS FULLY CHARGED PRIOR TO FIRST USE.. (1) RG1000 EMERGENCY JUMP STARTER PORTABLE POWER SUPPLY (1) 3-IN-1 USB CABLE (1) RG1000 EMERGENCY JUMP STARTER PORTABLE POWER SUPPLY
More informationUsing the power override wire. LED Interior Light System (Optional) Adjusting the shelves: TIPS:
Using the power override wire LED Interior Light System (Optional) If your keypad does not respond, don t be alarmed. Most likely the batteries are dead and need replacing. You will be able to open the
More informationDo not install and/or operate this safety product unless you have read and understand the safety information contained in this manual.
Installation and Operation Instructions MR Tri- Light Available in various color combinations, the MR Directional LED surface mount, tri-color warning light is ideal for a wide variety of auxiliary warning
More informationFirstmate Installation Manual and User's Guide May, 2003
Firstmate Installation Manual and User's Guide May, 2003 Aqualogic Marine, Inc. 506-D Terry Lane - Washington - Missouri - 63090 Warning No user serviceable parts are located inside your Firstmate unit.
More information"WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD200SS TUBE EXPANDER OPERATIONS MANUAL VERSION 4.3 LAST EDITED 06.17.15 cleanroomdevices.com Table of Contents Table of Contents....1
More informationModel P-40 & Model P-25 POWER PUSHER
Power Pusher Description INSTRUCTION MANUAL The Power Pusher provides ram capability by using the spreading power of the POWER HAWK P-16 Rescue Tool. (The Power Pusher may also be used with other spreader
More informationA Member of the. Integrated Metering Technologies
I n s t a l l a t i o n M a n u a l A Member of the Integrated Metering Technologies 1.0 General and safety Do not install, operate or maintain this flow meter without reading, understanding and followingthe
More informationStraight-Bore Clutch LSCC-32, 44, 54
Straight-Bore Clutch LSCC-32, 44, 54 1 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject to change without notice. Technical
More informationElectrically Released Motor Brake Module for EM-MBFB and EUM-MBFB
Electrically Released Motor Brake Module for EM-MBFB and EUM-MBFB P-1337-WE 819-0314 Installation Instructions An Altra Industrial Motion Company Warner Electric s MBFB series of Electrically Released
More informationFCB-450, LCB-600, MCB-800
AIR CHAMP PRODUCTS User Manual FCB-450, LCB-600, MCB-800 Clutch-Brakes (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are
More information182-LED Solar-Powered Motion Security Light. Owner s Manual
182-LED Solar-Powered Motion Security Light Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
More informationDigital Anti-Theft Wall Safe
Operation & Installation Guide 2070AF Manual # M08-0271-000 www.firstalert.com Digital Anti-Theft Wall Safe Manual # M08-0271-000 4 7 8 9 DIGITAL ELECTRONIC S AFE Index / Overview of Your Safe Index Overview
More informationNEW GEN OWNER S MANUAL
NEW GEN OWNER S MANUAL For Models: LT-ELP223Q LT-ELP116Q 1 2! Turn off the light when not in use to conserve battery power. CAUTION! If you need to mount the flashlight onto a firearm, make sure firearm
More information2-Pack Indoor/Outdoor Simulated Security Cameras. Owner s Manual
2-Pack Indoor/Outdoor Simulated Security Cameras Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
More informationTable of Contents. Page 2. midlandusa.com. Model PPG100
Table of Contents WELCOME TO THE WORLD OF MIDLAND... FEATURES... FCC NOTIFICATION... CONTROLS AND INDICATORS... LCD DISPLAY... CHARGING YOUR PPG100... AC Charging... 12V DC Car Charging... Solar Charging...
More informationTension your belts at the speed of light!
Tension your belts at the speed of light! OVERVIEW The Carlisle Frequency-Finder (part number 109061) is an electronic measuring instrument that precisely measures the static tension in Synchronous, V-Belts,
More informationDigital Clock model 75100C
Instruction Manual Digital Clock model 75100C CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Clock Setup... 4 Set the Time & Date... 5 Care
More information1000 lb. Adjustable Gantry Crane
1000 lb. Adjustable Gantry Crane Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationIMEX 66R ROTATING LASERS
IMEX 66R ROTATING LASERS OPERATION MANUAL OPERATING MANUAL ROTATING LASER IMEX 66R Introduction Congratulations on your purchase of a quality Imex rotating laser. These lasers have been designed for the
More informationMICROMANOMETER ALNOR MODEL AXD610 AIRFLOW INSTRUMENTS MODEL PVM610
MICROMANOMETER ALNOR MODEL AXD610 AIRFLOW INSTRUMENTS MODEL PVM610 OPERATION AND SERVICE MANUAL P/N 1980587, REV F SEPTEMBER 2014 Copyright TSI Incorporated / 2007-2014 / All rights reserved. Address
More informationWireless Thermometer model 00782W
Instruction Manual Wireless Thermometer model 00782W CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Setup... 4 Install or Replace Batteries...
More information10 Year Limited Warranty
Power. On Your Terms. 10 Year Limited Warranty PHI 2.7 TM PHI 3.5 TM 60A SIMPLIPHI POWER, INC. REV020618 10 Year Limited Warranty: PHI 2.7 TM PHI 3.5 TM 60A 24V 48V Limited Pro-Rated Warranty Coverage
More informationCONTENTS. Calibration Self Check & Technical Specifications 13 Care & Maintenance, Trouble Shooting 15 Warranty 16
CONTENTS User Safety 2 Introduction and 3L360 Accessories 3 3L360 Diagram 4 Operating Instructions 7 Batteries 7 Power 8 Manual Mode. 9 Pulse Mode 10 LLR705 Receiver (optional 3L360R only) 11 Mounting
More information2000 lb Adjustable Gantry Crane
2000 lb Adjustable Gantry Crane Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationDolly with Pneumatic Tires
Dolly with Pneumatic Tires Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More information3000-Lb. Vehicle Positioning Jacks. Owner s Manual
3000-Lb. Vehicle Positioning Jacks Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationSeries 2100 Operating Instructions
Series 2100 Operating Instructions Installation Instructions Visit the link below or scan the QR code to watch a detailed installation video: http://triteqlock.com/fresh After the lock, temperature probe,
More informationCONTENTS. Introduction. Thank you for purchasing the AlcoSense Precision+ breathalyser.
User Manual Introduction CONTENTS Thank you for purchasing the AlcoSense Precision+ breathalyser. The AlcoSense Precision+ is certified to Australian Standard AS3547 Type 2 Quantitative Device and is one
More information