10MFP 10MFP Filtration Trolley with icountpd

Size: px

Start display at page:

Download "10MFP 10MFP Filtration Trolley with icountpd"

Erik Barton
6 years ago
Views:

1 10MFP GB 10MFP Filtration Trolley with icountpd DD _EN Rev- 2012, Parker Hannifin Manufacturing (UK) Ltd

2 Contents Overview...3 Exclusion of Liability...3 Conditions for safe use...3 Safety Information...3 Dangers of maloperation or mishandling...3 Symbol glossary...4 Laser information...5 Calibration...5 Registration of icountpd...5 Contact Information...5 Technical specification...6 Product features...7 Electrical connections...7 Connecting/Disconnecting...8 Product operation...9 Maintenance...11 Ordering information Parker Hannifin Manufacturing (UK) Ltd

Overview Parker Hannifin s Filtration trolley allows you to transfer, condition monitor and filter fluid, whilst reporting contamination levels using the icountpd product The 10MFP Filtration Trolley

3 Overview Parker Hannifin s Filtration trolley allows you to transfer, condition monitor and filter fluid, whilst reporting contamination levels using the icountpd product The 10MFP Filtration Trolley measures particle contamination continuously and updates the results to the output display on the icountpd. Exclusion of Liability Parker has made every endeavour to ensure the accuracy of the content of this document, however errors cannot be ruled out. Consequently, we accept no liability for such errors as may exist or for any damage or loss whatsoever which may arise as a result of such errors. Technical specifications are subject to change without notice. Conditions for safe use WARNING : When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury. To ensure compliance with the certification, users are NOT permitted to open the unit s electrical or icountpd source under any circumstances. Doing so will invalidate the unit s calibration and it would NOT be suitable for calibrated use. Safety Information Please read and understand the Operating Instructions before using the equipment This filtration trolley weighs approximately 62kg (137 lbs). Two persons are required to lift the trolley one either side of the trolley gripping the handle and the trolley base. Before operating the Filtration trolley ensure all electrical connections, hoses and fittings are securely fitted to the appropriate standards. Check all hoses and fittings for wear and or damage. If replacements are required, please contact your local Parker Hannifin representative. Do NOT use or store this product in wet or damp environmental conditions. Best practice mounting orientation is to have the unit placed on a stable surface with easy access to the power switch and icountpd screen. The Filtration cart is designed for use in dry, indoor environments. There is no need to hold the trolley, but you may need to hold or secure the hose / wand assembly during operation. DO NOT attempt to move the trolley when in use. Do not remove the hose / wand assembly when in use. CAUTION: High pressure oil systems can be a hazard to life and limb. Dangers of maloperation or mishandling In case of maloperation, mishandling or abuse, as well as in cases ignoring the application limits and safety regulations, the following threats can occur: General Danger / Operator Injury Possible Equipment Damage when incorrectly connected to machines / systems or component devices. 10MFP Filtration Trolley with icountpd 3

Symbol glossary The following symbols are used in this manual.

personal injury exist in this equipment or may be associated with its use.

Caution A Caution notice is used in situations where inattention or misuse could cause damage to the equipment.

Check Notes merely call attention to information that is especially significant to understanding and operating the equipment.

Safety equipment Some operations require special attention to safety, such as the use of safety glasses.

4 Symbol glossary The following symbols are used in this manual. Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. A Warning notice is used in situations where inattention or misuse could cause personal injury. Caution A Caution notice is used in situations where inattention or misuse could cause damage to the equipment. If the equipment is used in a manner not specified by the manufacturer, the protection/performance may be impaired. Check Notes merely call attention to information that is especially significant to understanding and operating the equipment. You may need to check the orientation or tightness of connections, for example. Safety equipment Some operations require special attention to safety, such as the use of safety glasses. Service/Repair Any servicing or repair work must be carried out by a Parker-approved service centre. Warning A red band around a picture or instruction is used to emphasize that particular care is required to avoid the danger of personal injury or other hazard. Caution A yellow band around a picture or instruction is used to emphasize that particular care is required in carrying out the instruction. Examples are checking that plugs are keyed (i.e. correctly polarized) before they are fully inserted, or that hoses are fitted carefully so they do not leak. 4 Parker Hannifin Manufacturing (UK) Ltd

Laser information This product contains an infrared 5mW laser.

source and should never do so. Calibration Every 12 months www.

com/hfde/condition/service NOTE: Any servicing or repair work

5 Laser information This product contains an infrared 5mW laser. Any dismantling of the product may result in dangerous exposure to laser radiation. The following information about the laser is located on the side panel of the product. WARNING: Users are not required to access the laser radiation source and should never do so. Calibration Every 12 months NOTE: Any servicing or repair work must be carried out by a Parker-approved service centre. Registration of icountpd 12 Months Contact Information conmoninfo@parker.com See back page for contact details 10MFP Filtration Trolley with icountpd 5

6 Technical specification Feature Specification Dimensions (Approx.) (mm / inches) Height : 1029mm / 40.5" Width : 648mm / 25.5 Depth : 483mm / 19 Weight (Approx.) (Kg / llbs) Principle of operation IPD 62kg / 137 lbs Laser diode for optical detection of actual particulates International codes ISO 7 22 icountpd calibration icountpd recalibration Unit Ambient storage temperature Unit Operating Environment Recommended Fluid operating Viscosity (maximum) Pump Flow Rate 1st Stage Filtration (Suction / Inlet Filter) 2nd Stage Filtration (Pressure / Outlet Filter) By recognised online methods confirmed by the relevant ISO procedures: MTD via a certified primary ISO automatic particle detector using ISO principles, with particle distribution reporting to ISO 4406:1996 Every 12 months: conmoninfo@parker.com 26 C to +70 C ( 79 F to +158 F) DO NOT use the filtration trolley in wet or damp environmental conditions Up to 108 cst (500 SUS) (0.85 Specific Gravity) 38 l/min (10 GPM) Micron rating specified in MF Part number, Visual indicator (Optional), 0.2 bar (3 psi) bypass preventing MF pump cavitation Micron rating specified in MF Part number, Visual indicator, 1.7 Bar (25 psi) prevents excessive pressures Suction / Pressure Hose PVC (standard), 1 metre (39") Suction Pressure Wand PVC (standard), 1 metre (39") Certification IP22 rating EN Electrical equipment for measurement, control and laboratory EN A11:2010 Modified Safety of transportable motor operated electric tools 2006/42/EC Machinery Directive 6 Parker Hannifin Manufacturing (UK) Ltd

Product features 8 8 1 7 1 2 3 6 5 4 3 9 Key 1 2 3 4 Service covers Visual indicator Dual filters Gear pump 5 Motor 6 7 8 9 Electrical enclosure icountpd (icount Particle Detector) - refer to icount

The Filtration cart should not be used in wet or very humid environments. Electrical connections The Parker supplied power cables can only be used with the 10MFP products.

7 Product features Key Service covers Visual indicator Dual filters Gear pump 5 Motor Electrical enclosure icountpd (icount Particle Detector) - refer to icount user guide supplied on CD Hose and Wand assemblies Oil drip tray Parker recommend placing the 10MFP on a stable surface with easy access to the power switch and icountpd screen. The Filtration cart should not be used in wet or very humid environments. Electrical connections The Parker supplied power cables can only be used with the 10MFP products. UK plug (230V~, 5A fuse *) EUR plug 110VAC Industrial plug CAUTION: Only use the Parker-supplied Power Supply Cable. It is the responsibility of the end-user to ensure that the cables are connected and stored correctly to avoid any damage. Keep the power cord away from heat and sharp edges. Never yank the cable from the power socket. The use of any accessory or attachment other than recommended in this instruction leaflet may result in product damage or personal injury. * Anti-surge T LBC fuse, 5A 5x20mm 10MFP Filtration Trolley with icountpd 7

Connect electrical mains socket to trolley and lower the anti-yank wire clip. Connect mains plug to mains socket.

8 Connecting/Disconnecting 1 2 Ensure the panel power switch is in the OFF position. 3 Ensure hydraulic connections are made before starting unit. Connect electrical mains socket to trolley and lower the anti-yank wire clip. Connect mains plug to mains socket Turn overload switch ON. To remove electrical connections, switch off at trolley and mains supply and disconnect power cable. Turn panel switch ON. 8 Parker Hannifin Manufacturing (UK) Ltd

Product operation 1 2 Insert suction hose into the container for the fluid under test. Ensure the trolley is on a flat, stable surface and in dry conditions.

9 Product operation 1 2 Insert suction hose into the container for the fluid under test. Ensure the trolley is on a flat, stable surface and in dry conditions. Secure hoses if necessary, to avoid leakage/spray. 3 4 CAUTION: Make sure that the hose is not kinked. Insert pressure hose into waste fluid container. 5 See Electrical Connections set up (pages 7 8) 6 7 Turn overload switch ON. Turn panel switch ON. Parker recommend that you position the trolley in a safe stable area, as close as possible to the system output, using only the hose assemblies provided. NOTE: The correct hydraulic connection fittings have been supplied with this Filtration trolley and correct safety standards must be applied when using them. 10MFP Filtration Trolley with icountpd 9

8 9 Allow 30 60 seconds for filters to fill after starting trolley system For very

DO NOT restrict the discharge hose with a shut off valve.

10 8 9 Allow seconds for filters to fill after starting trolley system For very viscous fluids it may be necessary to put 1 2 litres of oil into the inlet filter to prime the pump. WARNING: The outlet filter bypass spring acts as a relief valve for the pump. DO NOT restrict the discharge hose with a shut off valve. This will cause excessive pressures in the product which may be harmful to personnel or your equipment. 9 bk A visual indicator monitors the condition of the filters and indicates CLEAN, CHANGE or BYPASS. bl Turn panel switch OFF when the specified fluid condition is met. Turn the overload switch OFF. 10 Parker Hannifin Manufacturing (UK) Ltd

Maintenance 1 2 See Electrical Connections set up (pages 7 8) Ensure the trolley is on a

Remove the suction and pressure hoses from fluid containers and place in trolley.

Care must be taken when removing hoses and the correct safety and disposal methods used.

5 6 Twist the cover to free the bolts and lift off.

7 8 Pull filter element assembly from housing.

11 Maintenance 1 2 See Electrical Connections set up (pages 7 8) Ensure the trolley is on a flat, stable surface and in dry conditions. Remove the suction and pressure hoses from fluid containers and place in trolley. CAUTION: The trolley may contain oil. Care must be taken when removing hoses and the correct safety and disposal methods used. 3 4 Loosen the bolts on the filter cover using a ½ socket set. 5 6 Twist the cover to free the bolts and lift off. Inspect the cover O-ring and replace if damaged or worn. 7 8 Pull filter element assembly from housing. Caution Wear appropriate protection if testing hydraulic fluids. Replace the filter media. Wire mesh elements can be ultrasonically cleaned (contact Parker for advice). Install new elements and replace filter O-ring. Caution Ensure O-ring is seated correctly before fitting filter cover. 10MFP Filtration Trolley with icountpd 11

bm Wipe traces of oil from trolley with paper or cloth and dispose in an appropriate

12 9 bk Check the notch of the element and cap are aligned. bl Replace the cover. Ensure washers are free of cover and twist to close. bm Wipe traces of oil from trolley with paper or cloth and dispose in an appropriate manner. Do not wet parts that could penetrate the motor, electrical unit or icountpd. Tighten the bolts. 12 Parker Hannifin Manufacturing (UK) Ltd

Ordering information icountpd FITTED: Part number Model Motor option Inlet element Outlet element Filter bowl length Electrical plug type Standard fitted elements Inlet Outlet 10MFP140SA10Q1UKPD

13 Ordering information icountpd FITTED: Part number Model Motor option Inlet element Outlet element Filter bowl length Electrical plug type Standard fitted elements Inlet Outlet 10MFP140SA10Q1UKPD 10MFP 1 40 SA 10Q 1 UK Q 10MFP140SA10Q1EURPD 10MFP 1 40 SA 10Q 1 EUR Q 10MFP240SA10Q1INDPD 10MFP 2 40 SA 10Q 1 IND Q STANDARD TROLLEY: Part number Model Motor option Inlet element Outlet element Filter bowl length Electrical plug type Standard fitted elements Inlet Outlet 10MFP140SA10Q1UK 10MFP 1 40 SA 10Q 1 UK Q 10MFP140SA10Q1EUR 10MFP 1 40 SA 10Q 1 EUR Q 10MFP240SA10Q1IND 10MFP 2 40 SA 10Q 1 IND Q KEY: Motor option 1 = 220/240V~ Motor option 2 = 110V~ IND = Industrial 110V~ UK option PD = icountpd, type IPD ACCESSORY PART NUMBERS Description Mains cable (UK 2m cable, 230V~, 5A antisurge fuse) Part number ACC6JE001 Mains cable (EUR 2m cable, 230V~) ACC6JE002 N72530 Filter cover O-ring replacement (x2) ACC6NX003 10MFP Filtration Trolley with icountpd 13

14 REPLACEMENT FILTER ELEMENT PART NUMBERS Parker Moduflow inlet filter (suction) 0.2 bar bypass Nitrile 20µ Microglass III element Q 40µ synthetic element µ stainless steel element Parker Moduflow inlet filter (pressure) 2.4 bar bypass Nitrile 2µ Microglass III element Q 5µ Microglass III element Q 10µ Microglass III element Q 20µ Microglass III element Q Water removal element Parker Hannifin Manufacturing (UK) Ltd

15 Parker Worldwide AE UAE, Dubai Tel: parker.me@parker.com AR Argentina, Buenos Aires Tel: AT Austria, Wiener Neustadt Tel: +43 (0) parker.austria@parker.com AT Eastern Europe, Wiener Neustadt Tel: +43 (0) parker.easteurope@parker.com AU Australia, Castle Hill Tel: +61 (0) AZ Azerbaijan, Baku Tel: parker.azerbaijan@parker.com BE/LU Belgium, Nivelles Tel: +32 (0) parker.belgium@parker.com BR Brazil, Cachoeirinha RS Tel: BY Belarus, Minsk Tel: parker.belarus@parker.com CA Canada, Milton, Ontario Tel: CH Switzerland, Etoy Tel: +41 (0) parker.switzerland@parker.com CN China, Shanghai Tel: CZ Czech Republic, Klecany Tel: parker.czechrepublic@parker.com DE Germany, Kaarst Tel: +49 (0) parker.germany@parker.com DK Denmark, Ballerup Tel: parker.denmark@parker.com ES Spain, Madrid Tel: parker.spain@parker.com FI Finland, Vantaa Tel: +358 (0) parker.finland@parker.com FR France, Contamine s/arve Tel: +33 (0) parker.france@parker.com GR Greece, Athens Tel: parker.greece@parker.com HK Hong Kong Tel: HU Hungary, Budapest Tel: parker.hungary@parker.com IE Ireland, Dublin Tel: +353 (0) parker.ireland@parker.com IN India, Mumbai Tel: IT Italy, Corsico (MI) Tel: parker.italy@parker.com JP Japan, Fujisawa Tel: +(81) KR South Korea, Seoul Tel: KZ Kazakhstan, Almaty Tel: parker.easteurope@parker.com LV Latvia, Riga Tel: parker.latvia@parker.com MX Mexico, Apodaca Tel: MY Malaysia, Subang Jaya Tel: NL The Netherlands, Oldenzaal Tel: +31 (0) parker.nl@parker.com NO Norway, Ski Tel: parker.norway@parker.com NZ New Zealand, Mt Wellington Tel: PL Poland, Warsaw Tel: +48 (0) parker.poland@parker.com PT Portugal, Leca da Palmeira Tel: parker.portugal@parker.com RO Romania, Bucharest Tel: parker.romania@parker.com RU Russia, Moscow Tel: parker.russia@parker.com SE Sweden, Spånga Tel: +46 (0) parker.sweden@parker.com SG Singapore Tel: SK Slovakia, Banská Bystrica Tel: parker.slovakia@parker.com SL Slovenia, Novo Mesto Tel: parker.slovenia@parker.com TH Thailand, Bangkok Tel: TR Turkey, Istanbul Tel: parker.turkey@parker.com TW Taiwan, Taipei Tel: UA Ukraine, Kiev Tel parker.ukraine@parker.com UK United Kingdom, Warwick Tel: +44 (0) parker.uk@parker.com US USA, Cleveland Tel: VE Venezuela, Caracas Tel: ZA South Africa, Kempton Park Tel: +27 (0) parker.southafrica@parker.com European Product Information Centre (24-hour) Freephone: (from AT, BE, CH, CZ, DE, EE, ES, FI, FR, IE, IT, PT, SE, SK, UK) 2012 Parker Hannifin Corporation. All rights reserved. DD _EN Rev -

Parflare ECO. Mobile Flaring Machine for Triple-Lok Hydraulic Fittings

Parflare ECO. Mobile Flaring Machine for Triple-Lok Hydraulic Fittings 37 Parflare ECO Mobile Flaring Machine for Triple-Lok Hydraulic Fittings It s also a piggy bank! Parflare ECO Economical. Simple. Safe. A full-fledged Triple-Lok fitting flaring machine at an economical