ATS - Automatic Transfer Switch. AMF - Automatic Mains Failure. Synchro/Parallel applications like: MPM - Multiple Prime Mover

Transcription

1 SICES Srl provides a wide range of smart genset controllers for several applications like: ATS - Automatic Transfer Switch AMF - Automatic Mains Failure Synchro/Parallel applications like: MPM - Multiple Prime Mover MSB - Multiple Stand-by SPtM or MPtM - Single or Multiple Parallel to Mains SPtM or MPtM - Single or Multiple Parallel to Mains in stand-by and back syncro

2 - SPM - Single Prime Mover No Mains Circuit Breaker (MCB) Genset Circuit Breaker (GCB) control Engine and alternator protections monitoring Remote start control and date / time scheduler Models of genset controllers: GC315 / GC310 / GC350 AMF & ATS - Automatic Mains Failure & Automatic transfer switch Mains Circuit Breaker (MCB) control Genset Circuit Breaker (GCB) control Engine and alternator protections monitoring (AMF) Remote start control and date / time scheduler Models of genset controllers: GC315 / GC310 / GC350 / ATS100

3 GC315 New AMF&ATS and SPM Genset controller which includes the main engine and alternator protections with True RMS readings. Just one product for analogue (with sensors) and CANBUS J1939 engines. GC310 AMF&ATS and SPM Genset controller which includes the main engine and alternator protections with True RMS readings. Just one product for analogue (with sensors) and CANBUS J1939 engines. GC350 - GC350R AMF&ATS and SPM Genset controller which includes the main engine and alternator protections with True RMS readings. Just one product for analogue (with sensors) and CANBUS J1939 engines. ATS100 ATS controller able to manage the switch between two sources (Mains or Gensets).

4 - Up to 16 gensets connected on the same bus. Advanced Synchro/Parallel controller for Island mode and Mains parallel function (integrated PLC editor). Up to 24 gensets connected on the same bus. When the load is supplied by several gensets connected on a bus and working in parallel, we talk about SYNCHR/PARALLEL applications. Supervisor controller for multiple mains parallel applications For example big factories, hospitals, datacentre need more than one genset able to supply the load in case of mains failure. Additionally, in case of desert plants where the Mains is not available, It s required the power of several gensets in order to supply the load. SICES Srl provides different types of Genset controllers able to monitor up to 24 gensets connected on the same bus and able to control all the operations for the synchronization and load sharing.

5 MPM - Multiple Prime Mover No Mains Circuit Breaker (MCB) Genset Circuit Breakers (GCB) control Engine and alternator protections monitoring Synchronization, Load sharing and Paralleling function Models of genset controllers: GC500Plus / DST4602 MSB - Multiple Stand-by Mains Circuit Breaker (MCB) control Genset Circuit Breakers (GCB) control Engine and alternator protections monitoring Synchronization, Load sharing and Paralleling function Models of genset controllers: GC500Plus / DST4602 SPtM Single Parallel to Mains with possibility of back synchro Mains Circuit Breaker (MCB) control Genset Circuit Breaker (GCB) control Engine, alternator, Mains protections monitoring Synchronization and Paralleling function Models of genset controllers: GC500Plus / DST4602 MPtM - Multiple Parallel to Mains with possibility of back synchro Mains Circuit Breaker (MCB) control Genset Circuit Breakers (GCB) control Engine, alternator, Mains protections monitoring Synchronization, Load sharing and Paralleling function Models of genset controllers: GC500Plus / DST4602 / MC100

6 DST4602 The most advanced Genset controller for synchro/parallel applications. Controller particularly suggested for complex plants like CHP plants where PLC functions are required. DST4602 is available in two versions: compact or split (one box to be mounted into the control panel and one display to be mounted on the door of the panel). GC500Plus - GC500R Genset controller for synchro/parallel applications (Island mode either Mains parallel). Just one controller able to cover a wide range of applications. Synchronizer and Load sharing included. MC100 Supervisor controller for multiple mains parallel applications with several gensets working in emergency mode

7 - GC315 GC310 GC350 ATS100 GC500Plus DST4602 MC100 AMF Functions (single stand-by) ATS Functions SYNCHR/PARALLEL applications (in island and/or with the mains, soft return) Internal Load Sharing and Synchronizer Load shedding Load management Mains circuit breaker (MCB) management, Master circuit breaker management (MGCB), Bus tie breaker management (BTB) Reverse synchronizing of the gen-set group operating in multi-island mode to the mains PLC Functions with PID Block Master and Gen set changeover switch or MCB management Management of multiple mains incomers True RMS readings on generator and mains voltages and currents Active, Reactive and apparent power measurement Frequency and power measurement on Mains input Mains protections Rate of Change of Frequency (81R RCF) Vector shift, 27, 59, 81<, 81> Additional mains protections: 27Q, 27T J1939 and MTU CAN interface RS232 Modbus RTU interface RS485 Modbus RTU (insulated) (insulated) MDEM GSM/PSTN Standard ption

8 - GC315 GC310 GC350 ATS100 GC500Plus DST4602 MC100 RJ45 Ethernet port (on board) (on board) SMS Management GPRS/GSM/GPS communications USB Port DIGITAL INPUT DIGITAL UTPUT 8 (6 programmable) 8 (6 programmable) 16 8 (6 programmable) Additional DIGITAL INPUT/UTPUT 16/16 16/16 16/ Additional ANALGICAL INPUT/ UTPUT 10+10/4 (1) 10+10/4 (1) 10+10/4 (1) 10+10/4 (1) 64/32 Periodical test Auto starting with timer Auto starting inhibition Events and data logging Fuel management Four alternative configurations SPLIT Version available (box + separated display) Dimensions 247x187x70 247x187x70 247x187x70 247x187x70 247x187x70 260x205x76mm 247x187x70 Display (pixel) 128 x x x x x x x 64 Marine Certication (RI.NA) (GC350R) (GC500R) Display languages UK, FR, ITA, RU, PT UK, FR, ITA, RU, PT UK, FR, ITA, RU, PT UK, FR, ITA, RU, PT UK, FR, ITA, RU, PT UK, FR, ITA, RU, DE, ES UK, ITA, RU (1) 10 Programmable analogical Input + 10 Analogical input listed in J1939 list + 4 Programmable and analogical output Standard ption

9 DITEL Expansion module for additional, digital and programmable I/. Model with CPU including 16 INPUTS Model without CPU including 8 UTPUTS. Compatibility with: GC315, GC310, GC350, GC500Plus, DST4602. DITHERM, DIVIT, DIGRIN, DANUT Expansion modules for additional, analogue I/. Different models based on the type of the sensor Compatibility with: GC315, GC310, GC350, GC500Plus, DST4602. REWIND, DANCE Communication modules for GPRS/GSM/GPS interface (Rewind) and for Ethernet interface (Dance) using the monitoring system SI.M.NE. MDEM GSM GL865 - Traditional modem GSM Compatibility with: ATS100, GC315, GC310, GC350, GC500Plus, DST4602.

10 GATEWAY MDBUS TCP/IT It s used to connect one or several Modbus RTU devices to an Ethernet network. Inbuilt Web server and possibility to manage up to 4 contemporary connections coming from different PC stations. Compatibility with: GC315, GC310, GC350, GC500Plus, DST4602, MC100 ELECTRIC FUEL PUMP 230V MANAGEMENT It s a kit which allows the detection of the fuel levels into the tank and the control of a refilling fuel pump 230V. Compatibility with: GC315, GC310, GC350, GC500Plus, DST4602. RUTER GSM Extensive device which allow to use one GSM modem for several controllers. The same for Gateway module- Compatibility with: GC315, GC310, GC350, GC500Plus, DST4602, MC100

11 SICES SUPERVISR It s a software by means it s possible to monitor, reset, and even program the controller from any remote place. It is a configurable tool able to display the single line of the diagram. In addition, by means different password levels it s possible to start and stop the genset. SI.M.NE Web based software for remote control of gensets using GPRS/GPS technology. It s particularly useful for rental gensets due to it s possible to know and to be advised in case of events (alarm, shut-down, change of status) or in case of the genset is moved from the set position. That software allows to contemporary control many gensets displayed in one screen shot. SI.M.NE has to be supported by two hardware: REWIND Modem GSM/GPRS and GPS (if a special antenna is connected) DANCE Device for an Ethernet connection

12 - - -