Energetic independence

Transcription

1 Energetic independence Control cabinet

2 Manual - automatic - parallel Control cabinet MANUAL CONTROL CABINET KO-R MRS Manual control cabinet can be mounted on genset or delivered separately. It includes the entire control and management of the engine and generator, and remote start of the genset. By pressing a button (key) genset starts and stops (also from a remote location). Genset can also start and stop by signals to be obtained from the outside (remote start). It consists of a metal electrical cabinet, manual control panel of the genset SMC10, the generator protection circuit breaker, emergency stop key and fuses. The cabinet is ready to connect the power cable for consumers on a copper strip or staples. AUTOMATIC CONTROL CABINET KO-A AMF Automatic control cabinet can be mounted on genset or delivered separately. It includes the entire control and management of the engine and generator, and remote start of the genset. It allows the automatic start of the genset at main power network failure and stop on its return. Automatic control cabinet can operate in the following modes: AUTO / MANUAL / TEST / OFF. Genset management is provided by the keys with mechanical feedback and a large graphic display. Management and control can be run also through remote computer (PC). It is possible to connect generating sets in the network. It consists of a metal electrical cabinet, automatic control panell of the genset SAC35, the generator safety switch, emergency stop key and fuses. The cabinet is ready to connect the cable of the consumers on a copper strip or staples.

3 Control panel SMC 10 Control panel SAC 35 Optional equipment (controls, SMC, SAC) RS232, RS485, USB Mode Bus Adapter, GSM-modem, software, remote screen, interface for starting the device, internet module, expansion I / O module. Functions / controllers Stubelj SMC 10 Stubelj SAC 35 Binary inputs / outputs 6/6 7/7 Analog inputs 3 3 Magnetic pick-up AMF function - Input configuration Output configuration Voltage measurement Genset / Mains 3 ph/- 3 ph/3 ph Current measurement 3 ph 3 ph, IDMT overcurrent kw/kwh measurement /- / History file - RTC with battery GCB/MCB control with feedback -1)/- / Battery charging alternator circuit J1939 interface - Internet support with IB-LITE with IB-LITE Extension modules - IGL-RA15, IG-IOM, IGS-PTM 8 analog gauge drivers o o RS232 or RS485 interface o o Modem interface o o MODBUS interface o o Remote display o o Cummins Modbus o o Legend: included - excluded o optional - plug-in module required 1) Automatic GCB control without feedback 2) Manual / Automatic GCB control, but without feedback

4 3ph Microprocessor control Stubelj SMC10 / SAC35 includes the following management and control for the genset: 3 phase AMF function* Over/Under frequency Over/Under voltage Voltage asymmetry 3-phase generator protections Over/Under frequency Over/Under voltage Current/Voltage asymmetry Overcurrent/Overload True RMS Voltage measurement 3 phase generator and mains* voltages Voltage range 277 V p-n, 480 V p-p Maximal measured voltage 300 V p-n PT ratio range True RMS current measurements 3 generator phase currents Current range 5 A Maximal measured current 10 A CT ratio range Power measurements Act / React Power and Power Factor per phase Active and Reactive Energy counter Event and performance log + RTC Event based history with 119 events Reason, Data and Time + all important values are stored Battery backed-up RTC Test Run scheduler User interface Graphic pixels display Multiple language capability Setpoints adjustable via keyboard or PC Buttons with mechanical feedback Inputs and outputs 3 analog inputs (0 20 ma or Resistive jumper selectable) 6 or 7* Binary inputs 6 or 7* Binary outputs Magnetic pick-up input D+ preexcitation terminal Optional 8 analog gauge drive outputs, compatible with VDO, Datcon gauges EFI engine support Cummins MODBUS Engine specific J1939 for all major manufacturers Diagnostic messages in plain text Communication interfaces Optional USB and RS232 plug-in modules MODBUS RTU (requires RS232 module) Internet Mechanical and operation parameters Unit dimension mm Sealed front face rated for IP65 Hard plexiglass LCD cover Hard plexiglass LCD cover -20 C +70 C standard version -40 C +70 C low temperature version Power supply voltage 8 36 V Voltage drops shorter than 50 ms do not affect operation * - Only for model SAC V OR OR OR PC MODEM SMC/SAC/SPC IG-IB C 8 GAUGE DRIVERS PLUG IN MODULE STOP BINARY INPUTS 6x MRS xx 7x AMF xx POWER SUPPLY 8 to 36 VDC + - ALARM BINARY OUTPUTS (OPEN COLLECTOR) 4x MRS xx 5x AMF xx SMC/SAC GENERATOR RS 232 MAINS INTERFACE PLUG IN MODULE MEASUREMENT VOLTAGE CAN - J1939 I/O EXTENSION OR IG-IOM IGS-PTM IGL-RA15 ENGINE D+ BINARY OUTPUTS (OPEN COLLECTOR) ANALOG INPUTS MEASUREMENT VOLTAGE CURRENT GENERATOR C.B. CONTROL MAINS C.B. CONTROL Aux Alternator Preexcitation Oil pressure Starter Fuel Solenoid 2 RPM 3ph 3ph MAINS LOAD DIESEL/GAS ENGINE GENERATOR J1939 Start/Stop - Speed Request Values + Fault Codes

5 PARALLEL SYNCHRONIZATION CONTROL CABINET KO-P AMF Automatic sync control cabinet can be mounted on genset or separately. It includes the entire control and management of the engine and generator, and remote start of the genset. It enables the automatic start of the genset when main power network fails and stops on its return. It also enables synchronization of network and genset and parallel operation of the genset and main electric network. The parallel synchronization control cabinet can also cover electrical spikes. In case that the designated facility needs additional electricity, genset in parallel operation can add this deficit to the main electrical grid. Genset can also cover a specific part of the power so that is no need to be collected from the main electricity network and pay credits at a higher rate. Genset performs uninterrupted switching between the network and genset. It is also possible for uninterrupted test of the genset at full or partial load. Genset management is possible by keys with mechanical feedback and a large graphical display. Management and control can be run also through remote computer (PC). It is possible to connect generating sets in the network. It consists of a metal electrical cabinet, parallel control panel of the genset Stubelj SPC50, the generator safety switch, battery charger emergency stop key and fuses. The cabinet is ready to connect the cable to consumers on a copper strip or staples. Parallel control SPC 50 Extensions: 4 analog inputs Ω, 8 digital inputs, 8 binary outputs, 1 analogue output, 4 analog inputs Ω/0-20 ma/ mv, 8 digital inputs, 8 binary outputs, 1 analogue output, 15 green / yellow / red LED indicators. Communication Extensions: Ethernet / Internet communication supports control of multiple generating sets over the Internet, an active on error on genset, internet function call / callback. Direct or modem control of multiple generating sets RS232 / RS485 / ModeBus support for direct connection, analog / GSM / ISDN modem support, call-back feature on your modem. Software for PC or PC SCADA. Software for PC for long-term monitoring of events multiple generating sets. Controller software for automatic acquisition of data on multiple genset via modem. Remote display connected via RS232, to transfer all of the displayed values to 1.2 km away - the exact copy of the OSD control.

6 UPGRADING ATS automatic transfer switch genset / mains Control power (for one genset in parallel with the network): automatic synchronization and control of power, cutting peaks, uninterrupted reverse synchronization, voltage control PF (AVR), basic load export / import. Load sharing (for more isolated parallel operation): automatic synchronization and control of power, voltage and PF control (AVR), active load sharing. Load sharing and power management (for more isolated parallel operation or more motors parallel with the network): automatic synchronization and control of power, voltage control PF (AVR), active load sharing, the sharing of Var (via CAN bus). All data in this catalogue are informative and are subiect to changes without prior notice. Optimizing the number of operating generating sets: power management (via CAN bus) in kw or % of the power, monitoring and control of multiple generating sets via MultiEdit. Austria Hungary Italy Stubelj d.o.o. Anhovo Nova Gorica Udine Trieste Croatia STUBELJ d.o.o., Anhovo 14, 5210 Deskle, Slovenia, EU, tel: / , fax: / , info@stubelj.si,