Stainless One-touch Fittings. Applicable Tubing Tubing material Tubing O.D. Specifications. Ambient and fluid temperature

Transcription

1 Stainless One-touch Fittings Series KG Guide Collet Chuck Suitable for use with nylon, soft nylon and urethane. Large retaining force. as large retaining force while holding force is increased by the collet. Release button (White) Light force for removal When the fitting is removed from the, the chuck and collet are released, thus preventing them from biting into the tube excessively. Seal Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0 MPa The use of a special profile ensures sealing and reduces resistance when the tube is inserted. PAT. Body (White) O-ring Tube Stud Effective when piping in a confined space. The body and the ed portion can rotate. Stainless specifications applicable to corrosive environments Stainless steel 303 adopted for metal elements Suitable for use in CRT production lines where contact with copper must be avoided, food processing machines where water or salt water splashes and clean room where discoloration of copper material and corrosion must be avoided. Tubing Tubing material Tubing O.D. Specifications Ambient and fluid temperature Mounting section Thread Nut section Seal (Thread portion) Principal Parts Material Nylon, Soft nylon, Polyurethane ø, ø, ø, ø, ø, ø1 Fluid Air/Water (1) Maximum operating pressure 1.0 MPa Operating vacuum pressure 0 kpa Proof pressure 3.0 MPa 5 to 0 C (Water: 0 to 0 C) (No freezing) JIS B 0203 (Taper for piping) JIS B 0211 Class 2 (Metric fine ) With seal or none (2) Note 1) for general industrial water. Please consult with SMC if using for other kinds of fluid. Also, the surge pressure must be under the maximum operating pressure. Note 2) Suffix S to the part number, if w/ seal is desired. Body Stud Chuck Guide Collet, Release button Seal, O-ring Stainless steel 303, PBT Stainless steel 303 Stainless steel 30 Stainless steel 30, Stainless steel 303, POM POM NBR 15-3-

2 Stainless One-touch Fittings Series KG ex. socket head male connector KGS P. Internal hex. allows connection by using an allen wrench for confined spaces. Bulkhead union KGE P. 1 Use to connect tubes through a panel. Universal male elbow KGV P. Extended male elbow KGW P. 1 Basically, it is used together with male elbow. Different point is that it is used for fittings to avoid from interfering with each other by making the piping two-level. K M Universal male elbow allows connection by using a socket wrench for confined spaces. Bulkhead connector KGE P. 1 Use to connect male thead and tube through a panel. D MS T Male connector KG P. Use to pipe in the same direction from female. Most general style. Male elbow KGL P. 11 Use to pipe at right angles to female. Most general style. Male branch tee KGT P. 1 Use to branch line from female in both 90 directions. VMG Female connector Union elbow Union tee KGF P. 11 Use to pipe from male such as pressure gauge. KGL Use to connect tubes at right angles. KGT P. 1 Use to connect tubes in both 90 directions. P. 13 Straight union KG P. 11 Use to connect tubes in the same direction. Plug-in elbow KGL P. 13 Use to change by 90 in a tube fetching direction from Onetouch fittings. Different diameter tee KGT P. 15 Use to connect tubes with size down in both 90 directions. Different diameter straight KG P. 11 Use to connect different sized tubes. Male delta union KGD Use to branch line in 90 direction from female. Male run tee KGY P. 15 Use to branch line in the same direction from female and in 90 direction. P. 15 Male branch connector Delta union Different dia. double union Y KGLU P. Use to branch line KGD P. 1 Use to branch KGUD P. at right angles to line in tripple 90 female. direction. Use to four-branch line in the same direction. Branch union elbow KGLU P. 13 Use to branch line at right angles. Delta branch KGUD P. 1 Use to four-branch line in the same direction from female. Union Y KGU P. Use to branch line in the same direction

3 Series KG Different dia. union Y KGU P. Use to connect tubes in the same direction, reducing the size of tubes. Plug-in reducer KGR P. Tube cap KGC P. 1 Use to change size of One-touch fittings. Use to plug unused. Branch KGU P. 1 Use to branch line in the same direction from the female. Male Connector: KG 1 (1) across ød L A M R M5 x 0. KG0-M KG KG (2) M5 x 0. KG0-M KG KG KG KG KG KG KG KG KG KG KG KG KG KG (1) KG (9) 7 Reference dimensions after R installation. Note 1) ød: Max. diameter Note 2) ( ): Values for nylon. exagon Socket ead Male Connector: KGS L A M across ød KGS0-M KGS KGS0-M KGS KGS KGS KGS KGS KGS KGS KGS KGS KGS KGS KGS Reference dimensions after R installation. ød: Max. diameter R M5 x 0. 1 M5 x

4 Stainless One-touch Fittings Series KG Female Connector: KGF Straight Union: KG 2-applicable L1 L2 M across ød Rc 1 KGF KGF KGF0-01 KGF KGF0-03 KGF0-01 KGF0-02 KGF KGF KGF KGF KGF KGF ød: Max. diameter L M ød KG KG KG KG KG ød: Max. diameter K M D MS T VMG Different Diameter Straight: KG a b L M1 ød M2 a b KG KG KG KG ød: Max. diameter Male Elbow: KGL 1 R M5 x M5 x KGL0-M5 KGL0-01 KGL0-02 KGL0-M5 KGL0-01 KGL0-02 KGL0-03 KGL0-01 KGL0-02 KGL0-03 KGL-01 KGL-02 KGL-03 KGL-0 KGL-02 KGL-03 KGL-0 KGL1-03 KGL1-0 across (1) ød1 ød2 L1 L2 A M (2) mm (71) 1 0 () 5 Reference dimensions after R installation. Note 1) ød1: Max. diameter Note 2) ( ): Values for nylon

5 Series KG Male Branch Connector: KGLU R M5 x 0. 1 across 1 KGLU0-M5 KGLU0-01 KGLU M5 x 0. KGLU0-M5 1 KGLU KGLU0-02 KGLU0-03 KGLU0-01 KGLU0-02 KGLU KGLU-02 3 KGLU KGLU-0 KGLU-02 KGLU KGLU-0 ød L1 L2 L3 A M P Q1 Q Reference dimensions after R installation. ød: Max. diameter 2-applicable Universal Male Elbow: KGV M3 x 0.5 R M5 x 0. 1 M5 x KGV0-M5 KGV0-01 KGV0-M5 KGV0-01 KGV0-02 KGV0-01 KGV0-02 KGV0-03 KGV-02 KGV-03 KGV-03 KGV-0 across 1 1 ød1 ød2 L1 L2 L3 A M Reference dimensions after R installation. ød1: Max. diameter 15-3-

6 Stainless One-touch Fittings Series KG Union Elbow: KGL 2-applicable Branch Union Elbow: KGLU ød L Q ød (1) L1 L2 Q1 KGLU KGLU KGLU KGLU KGLU ød: Max. diameter Q2 M P (2) KGL KGL KGL KGL KGL KGL () 29 Note 1) ød: Max. diameter Note 2) ( ): Values for nylon. M2 K M D MS T VMG 3-applicable Plug-in Elbow: KGL fitting size ød tube O.D. mm fitting size ød ød1 ød2 L1 L2 A M KGL KGL KGL KGL KGL ød1: Max. diameter

7 Series KG Extended Male Elbow: KGW M5 x 0. O.D. (mm) ød1 ød2 L1 L2 A across M R M5 x 0. KGW0-M KGW KGW M5 x 0. KGW0-M KGW KGW KGW KGW0-01 KGW KGW KGW KGW KGW KGW KGW KGW-0.5 Reference dimensions after R installation. ød1: Max. diameter Male Branch Tee: KGT 2-applicable (1) (2) O.D. ød1 ød2 L1 L2 A M across (mm) R M5 x 0. KGT0-M KGT KGT M5 x 0. KGT0-M KGT KGT KGT KGT0-01 KGT KGT KGT KGT KGT KGT KGT KGT KGT KGT (71) KGT (0) 11 Reference dimensions after R installation. Note 1) ød1: Max. diameter Note 2) ( ): Values for soft nylon Union Tee: KGT 3-applicable O.D. (mm) 1 (1) (2) ød L Q M KGT KGT KGT KGT KGT KGT () 0 Note 1) ød: Max. diameter Note 2) ( ): Values for nylon

8 Stainless One-touch Fittings Series KG Different Diameter Tee: KGT a b ød1 ød2 L1 L2 Q M1 M2 KGT KGT KGT KGT ød1: Max. diameter K M Male Run Tee: KGY 2-applicable 2-applicable (1) O.D. ød1 ød2 L1 L2 A (2) M (mm ) across L3 (mm) R M5 x 0. KGY0-M KGY KGY M5 x 0. KGY0-M KGY KGY KGY KGY KGY KGY KGY KGY KGY KGY KGY KGY KGY KGY (1) KGY (113) 11 Reference dimensions after R installation. Note 1) ød1: Max. diameter Note 2) ( ): Values for nylon. D MS T VMG Male Delta Union: KGD 2-applicable 2-applicable O.D. (mm) ød L1 L2 A across M Q R M5 x 0. KGD0-M KGD KGD M5 x 0. KGD0-M KGD KGD KGD KGD KGD KGD KGD KGD KGD KGD-02 KGD KGD Reference dimensions after R installation. ød: Max. diameter

9 Series KG Delta Union: KGD 3-applicable ød KGD KGD KGD KGD KGD L M ød: Max. diameter Q Branch Y : KGU 2-applicable 2-applicable R M5 x 0. 1 KGU0-M5 KGU KGU M5 x KGU0-M5 KGU0-01 KGU0-02 KGU0-03 KGU KGU KGU KGU-02 3 KGU KGU-0 1 KGU-02 3 KGU KGU-0 ød A M across L P Reference dimensions after R installation. ød: Max. diameter Delta Branch: KGUD -applicable across R 1 KGUD KGUD KGUD KGUD0-02 ød1 ød2 L I A Q M P Reference dimensions after R installation. ød1: Max. diameter

10 Stainless One-touch Fittings Series KG Union Y : KGU Different Diameter Union Y : KGU 3-applicable ød L1 KGU KGU KGU KGU KGU M1 ød1 ød2 L1 L2 P Q M2 a b KGU KGU KGU KGU ød1, ød2: Max. diameter L2 M ød: Max. diameter P Q K M D MS T VMG Different Diameter Double Union Y : KGUD M1 ød1 ød2 L1 L2 P I Q M2 a b KGUD KGUD ød1, ød2: Max. diameter -applicable a b Plug-in Reducer: KGR fitting size ød fitting size ød 1 1 (1) (2) ød L A M KGR KGR KGR KGR KGR KGR KGR KGR KGR0-2. KGR KGR (29.5) 2 KGR (.1) 37 Note 1) ød: Max. diameter Note 2) ( ): Values for nylon

11 Series KG Bulkhead Union: KGE Mounting plate thickness 11 mm or less (1) Mounting M T (M) across L hole KGE0-00 M x KGE0-00 M1 x KGE0-00 M1 x KGE-00 M20 x KGE-00 M x KGE1-00 M2 x (9) 115 Dimensions in ( ) are the case of soft nylon tube. Bulkhead Connector: KGE Mounting plate thickness 7 mm or less (1) T (M) L1 L2 Mounting M across across Rc hole 1 KGE M x KGE KGE KGE0-02 M1 x KGE KGE KGE0-02 M1 x KGE KGE M20 x KGE KGE M x KGE KGE M2 x (9) 2 KGE Dimensions in ( ) are the case of soft nylon tube. Tube Cap: KGC L M ød KGC KGC KGC KGC KGC KGC ød: Max. diameter

12 Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 1 Note 1), JIS B 370 Note 2) and other safety practices. Caution : Operator error could result in injury or equipment damage. Warning : Operator error could result in serious injury or loss of life. Danger : In extreme conditions, there is a possible result of serious injury or loss of life. Note 1) ISO 1: Pneumatic fluid power--general rules relating to systems. Note 2) JIS B 370: General Rules for Pneumatic Equipment Warning 1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements. The expected performance and safety assurance will be the responsibility of the person who has determined the compatibility of the system. This person should continuously review the suitability of all items specified, referring to the latest catalog information with a view to giving due consideration to any possibility of equipment failure when configuring a system. 2. Only trained personnel should operate pneumatically operated machinery and equipment. Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators. 3. Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1. Inspection and maintenance of machinery/equipment should only be performed once measures to prevent falling or runaway of the driver objects have been confirmed. 2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply pressure for this equipment and exhaust all residual compressed air in the system. 3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston rod, etc.. Contact SMC if the product is to be used in any of the following conditions: 1. Conditions and environments beyond the given specifications, or if product is used outdoors. 2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and brake circuits in press applications, or safety equipment. 3. An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis

13 Common Precautions Be sure to read before handling. For detailed precautions on every series, refer to main text. Warning Selection 1. Confirm the specifications. Products represented in this catalog are designed for use in compressed air appllications only (including vacuum), unless otherwise indicated. Do not use the product outside their design parameters. Please contact SMC when using the products in applications other than compressed air (including vacuum). Warning Mounting 1. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. 2. Securing the space for maintenance When installing the products, please allow access for maintenance. 3. Tightening torque When installing the products, please follow the listed torque specifications. Caution Piping 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe s or sealing material do not get inside the piping. Also, when the pipe tape is used, leave 1.5 to 2 ridges exposed at the end of the s. Warning Air Supply 1. Operating fluid Please consult with SMC when using the product in applications other than compressed air (including vacuum). Regarding products for general fluid, please ask SMC about applicable fluids. 2. Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines. If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed. For compressed air quality, refer to Air Preparation Equipment catalog.. Use clean air If the compressed air supply is contaminated with chemicals, cynthetic materials, corrosive gas, etc., it may lead to break down or malfunction. Warning Operating Environment 1. Do not use in environments where the product is directly exposed to corrosive gases, chemicals, salt water, water or steam. 2. Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibrations and/or shocks.. Do not mount the product in locations where it is exposed to radiant heat. Warning Maintenance 1. Maintenance procedures are outlined in the operation manual. Not following proper procedures could cause the product to malfunction and could lead to damage to the equipment or machine. 2. Maintenance work If handled improperly, compressed air can be dangerous. Assembly, handling and repair of pneumatic systems should be performed by qualified personnel only. 3. Drain flushing Remove drainage from air filters regularly. (Refer to the specifications.). Shut-down before maintenance Before attempting any kind of maintenance make sure the supply pressure is shut of and all residual air pressure is released from the system to be worked on. 5. Start-up after maintenance and inspection Apply operating pressure and power to the equipment and check for proper operation and possible air leaks. If operation is abnormal, please verify product set-up parameters.. Do not make any modifications to be product. Do not take the product apart

14 Quality Assurance Information (ISO 9001, ISO 1001) Reliable quality of products in the global market To enable our customers throughout the world to use our products with even greater confidence, SMC has obtained certification for international standards ISO 9001 and ISO 1001, and created a complete structure for quality assurance and environmental controls. SMC products pursue to meet its customers expectations while also considering company s contribution in society. Quality management system ISO 9001 This is an international standard for quality control and quality assurance. SMC has obtained a large number of certifications in Japan and overseas, providing assurance to our customers throughout the world. SMC s quality control system Quality system education Training of suppliers Make customers our first priority, offering them reliable and friendly service. Produce the highest quality with the participation of all employees. Quality policies Market research Product planning After service Sales coordination Research Education Design Training Development Production Process control Inspection, testing, etc. Initial production control Create new products using the latest technology, and offer the finest products in a timely manner. Quality control activities New product evaluation Reliability design Reliability testing New technical development Environmental management system ISO 1001 This is an international standard related to environmental management systems and environmental inspections. While promoting environmentally friendly automation technology, SMC is also making diligent efforts to preserve the environment

15 SMC Product Conforming to Inter SMC products complying with EN/ISO, CSA/UL standards are supporting CE Mark The CE mark indicates that machines and components meet essential requirements of all the EC Directives applied. It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and components are exported to the member Nations of the EU. Once A manufacturer himself declares a product to be safe by means of CE marking (declaration of conformity by manufacturer), free distribution inside the member Nations of the EU is permissible. CE Mark SMC provides CE marking to products to which EMC and Low Voltage Directives have been applied, in accordance with CETOP (European hydraulics and pneumatics committee) guide lines. As of February 9, the following 1 countries will be obliged to conform to CE mark legislation Iceland, Ireland, United Kingdom, Italy, Austria, Netherlands, Greece, Liechtenstein, Sweden, Spain, Denmark, Germany, Norway, Finland, France, Belgium, Portugal, Luxembourg EC Directives and Pneumatic Components Machinery Directive The Machinery Directive contains essential health and safety requirements for machinery, as applied to industrial machines e.g. machine tools, injection molding machines and automatic machines. Pneumatic equipment is not specified in Machinery Directive. owever, the use of SMC products that are certified as conforming to EN Standards, allows customers to simplify preparation work of the Technical Construction File required for a Declaration of Conformity. Electromagnetic Compatibility (EMC) Directive The EMC Directive specifies electromagnetic compatibility. Equipment which may generate electromagnetic interference or whose function may be compromised by electromagnetic interference is required to be immune to electromagnetic affects (EMS/immunity) without emitting excessive electromagnetic affects (EMI/emission). Low Voltage Directive This directive is applied to products, which operate above 50 VAC to 00 VAC and 75 VDC to 1500 VDC operating voltage, and require electrical safety measures to be introduced. Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/l. Such vessels require EC type examination and then CE marking

16 national Standards SMC Product Conforming to International Standards you to comply with EC directives and CSA/UL standards. Mark of compliance for CSA/UL Mark of compliance for CSA CSA Standards & UL Standards UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric products, and are defined to mainly prevent danger from electric shock or fire, resulting from trouble with electric products. Both UL and CSA standards are acknowledged in North America as the first class certifying body. They have a long experience and ability for issuing product safety certificate. Products approved by CSA or UL standards are accepted in most states and governments beyond question. Since CSA is a test certifying body as the National Recognized Testing Laboratory (NRTL) within the jurisdiction of Occupational Safety and ealth Administration (OSA), SMC was tested for compliance with CSA Standards and UL Standards at the same time and was approved for compliance with the two Standards. The above CSA NRTL/C logo is described on a product label in order to indicate that the product is approved by CSA and UL Standards. TSSA (MCCR) Registration Products TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi (0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation. Products conforming to CE Standard With CE symbol for simple visual recognition In this catalog each accredited product series is indicated with a CE mark symbol. owever, in some cases, every available models may not meet CE compliance. Please visit our web site for the latest selection of available models with CE mark

17 SMC s Global Service Network America U.S.A. SMC Corporation of America 3011 North Franklin Road Indianapolis, IN, U.S.A. TEL: FAX: CANADA SMC Pneumatics (Canada) Ltd. 7 Financial Drive Mississauga, Ontario, L5N 7J Canada TEL: FAX: MEXICO SMC Corporation (Mexico), S.A. DE C.V. Carr. Silao-Trejo K.M. 2.5 S/N, Predio San Jose del Duranzo C.P. 30, Silao, Gto., Mexico TEL: FAX: /2-59- CILE SMC Pneumatics (Chile) S.A. Av. La Montaña 1,115 km. 1,5 P. Norte Parque Industrial Valle Grande, Lampa Santiago, Chile TEL: FAX: ARGENTINA SMC Argentina S.A. Teodoro Garcia 30 (127) Buenos Aires, Argentina TEL: FAX: BOLIVIA SMC Pneumatics Bolivia S.R.L. Avenida Beni Numero 5 Santa Cruz de la Sierra-Casilla de Correo 1, Bolivia TEL: FAX: VENEZUELA SMC Neumatica Venezuela S.A. Apartado 0152, Avenida Nueva Granada, Edificio Wanlac, Local 5, Caracas 0-A, Venezuela TEL: FAX: PERU (Distributor) IMPECO Automatizacion Industrial S.A. AV. Canevaro 752, Lince, Lima, Peru TEL: FAX: URUGUAY (Distributor) BAKO S.A. Galicia 150 esq. Gaboto C.P. 100, Montevideo, Uruguay TEL: FAX: BRAZIL SMC Pneumaticos Do Brasil Ltda. Rua. Dra. Maria Fidelis, nr. 130, Jardim Piraporinha-Diadema-S.P. CEP: , Brasil TEL: FAX: COLOMBIA (Distributor) Airmatic Ltda. Calle Apart. Aereo 05 Santa Fe de Bogotá, Colombia TEL: FAX: Europe U.K. SMC Pneumatics (U.K.) Ltd. Vincent Avenue, Crownhill, Milton Keynes, MK 0AN, Backinghamshire, U.K. TEL: FAX: GERMANY SMC Pneumatik Gmb Boschring D-3329 Egelsbach, Germany TEL: FAX: ITALY SMC Italia S.p.A. Via Garibaldi 2 I-2001 Carugate Milano, Italy TEL: FAX: FRANCE SMC Pneumatique S.A. 1 Boulevard de Strasbourg, Parc Gustave Eiffel, Bussy Saint Georges, F-7700 Marne La Vallee Cedex 3 France TEL: FAX: SWEDEN SMC Pneumatics Sweden AB Ekhagsvägen 29-31, S uddinge, Sweden TEL: FAX: SWITZERLAND SMC Pneumatik AG Dorfstrasse 7, Postfach 1, C- Weisslingen, Switzerland TEL: FAX: AUSTRIA SMC Pneumatik Gmb (Austria) Girakstrasse, A-20 Korneuburg, Austria TEL: FAX: SPAIN SMC España, S.A. Zuazobidea 1 Pol. Ind. Júndiz 015 Vitoria, Spain TEL: FAX: IRELAND SMC Pneumatics (Ireland) Ltd Citywest Business Campus, Naas Road, Saggart, Co. Dublin, Ireland TEL: FAX: NETERLANDS (Associated company) SMC Pneumatics BV De Ruyterkade 0, NL-11 AB Amsterdam, Netherlands TEL: FAX: GREECE (Distributor) S.Parianopoulos S.A. 7, Konstantinoupoleos Street 1155 Athens, Greece TEL: FAX: DENMARK SMC Pneumatik A/S Knudsminde B DK-300 Odder, Denmark TEL: FAX:

18 SMC s Global Service Network Europe FINLAND SMC Pneumatics Finland OY PL72, Tiistinniityntie, SF-031 ESP00, Finland TEL: FAX: NORWAY SMC Pneumatics Norway A/S Vollsveien 13C, Granfoss Næringspark N-13 LYSAKER, Norway TEL: FAX: BELGIUM (Distributor) SMC Pneumatics N.V./S.A. Nijverheidsstraat 20 B-210 Wommelgem Belguim TEL: FAX: POLAND SMC Industrial Automation Polska Sp.z.o.o. ul. Konstruktorska 11A, PL Warszawa, Poland TEL: FAX: TURKEY (Distributor) Entek Pnömatik San.ve Tic. Ltd. Sti Perpa Tic. Merkezi Kat:11 No Okmeydani Istanbul, Türkiye TEL: FAX: RUSSIA SMC Pneumatik LLC. 3/0 Sredny prospect V.O. St. Petersburg 900, Russia TEL: FAX: CZEC SMC Industrial Automation CZ s.r.o. udcova 7a, CZ-00 Brno, Czech Republic TEL: FAX: UNGARY SMC ungary Ipari Automatizálási kft. Budafoki ut Budapest TEL: FAX: ROMANIA SMC Romania S.r.l. Str. Frunzei, Nr. 29, Sector 2, Bucharest, Romania TEL: FAX: SLOVAKIA SMC Priemyselná automatizáciá, s.r.o Nova 3, SK-33 Bratislava TEL: FAX: SLOVENIA SMC Industrijska Avtomatilca d.o.o. Grajski trg 15, SLO- 30 Zuzemberk, Slovenia TEL: FAX: SOUT AFRICA (Distributor) yflo Southern Africa (Pty.) Ltd. P.O.Box 20 Paardeneiland 720 South Africa TEL: FAX: EGYPT (Distributor) Saadani Trading & Ind. Services 15 Sebaai Street, Miami 2111 Alexandria, Egypt TEL: FAX: Oceania/Asia AUSTRALIA SMC Pneumatics (Australia) Pty.Ltd. 1-1 udson Avenue Castle ill NSW 215, Australia TEL: FAX: NEW ZEALAND SMC Pneumatics (New Zealand) Ltd. C Sylvia Park Road Mt.Wellington Auckland, New Zealand TEL: FAX: TAIWAN SMC Pneumatics (Taiwan) Co.,Ltd., Lane 205, Nansan Rd., Sec.2, Luzhu-siang, Taoyuan-sien, TAIWAN TEL: FAX: ONG KONG SMC Pneumatics (ong Kong) Ltd. 29/F, Clifford Centre, 77-7 Cheung, Sha Wan Road, Lai Chi Kok, Kowloon, ong Kong TEL: FAX: SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd. 9 Tuas Avenue 1, Jurong Singapore TEL: 1-0 FAX: 1- PILIPPINES SOKETSU SMC Corporation Unit 201 Common Goal Tower, Madrigal Business Park, Ayala Alabang Muntinlupa, Philippines TEL: FAX: MALAYSIA SMC Pneumatics (S.E.A.) Sdn. Bhd. Lot 3 Jalan Delima1/1, Subang i-tech Industrial Park, Batu Shah Alam Selangor, Malaysia TEL: FAX: SOUT KOREA SMC Pneumatics Korea Co., Ltd. Woolim e-biz Center (Room 0), 0-5, Guro-Dong, Guro-Gu, Seoul, , South Korea TEL: FAX: CINA SMC (China) Co., Ltd. 7 Wan Yuan St. Beijing Economic & Technological Development Zone 0, China TEL: FAX: TAILAND SMC Thailand Ltd. 13/ Moo 5, Tiwanon Road, Bangkadi, Amphur Muang, Patumthani 000, Thailand TEL: FAX: INDIA SMC Pneumatics (India) Pvt. Ltd. D-7 to 1, Phase-2, Extension, Noida, Dist. Gautaim Budh Nagar, U.P , India TEL: (00)-5730 FAX: INDONESIA (Distributor) P.T. Riyadi Putera Makmur Jalan ayam Wuruk Komplek Glodok Jaya No Jakarta 1110 Indonesia TEL: FAX: PAKISTAN (Distributor) Jubilee Corporation First Floor Mercantile Centre, Newton Road Near Boulton Market P.O. Box 15 Karachi 7000 Pakistan TEL: /9 FAX: ISRAEL (Distributor) Baccara Automation Control Kvutzat Geva 15 Israel TEL: FAX: SAUDI ARABIA (Distributor) Assaggaff Trading Est. P.O. Box 335 Al-Amir Majed Street, Jeddah-21, Saudi Arabia TEL: FAX: