Evaluates: MAX14746/MAX MAX14746 Evaluation Kit. Detailed Description of Hardware. General Description. Features
|
|
|
- Frank Newman
- 5 years ago
- Views:
Transcription
1 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 General Description The MAX7 evaluation kit (EV kit) is a fully assembled and tested circuit for evaluating the MAX7/ MAX77 charger detectors with a linear battery charger and a smart power selector. Refer to the MAX7 IC data sheet for detailed information regarding the operation and features of the devices. The EV kit comes standard with the MAX7 installed, but can also be used to evaluate the MAX77 by replacing the MAX7 (U) with the MAX77. Request a free sample of the MAX77 when ordering the EV kit. Features RoHS Compliant Proven PCB Layout Full Assembled and Tested IC Serial Interface Ordering Information appears at end of data sheet. Detailed Description of Hardware Jumper Descriptions Table details the functions of the configurable jumper headers on the EV kit board. The headers are standard 0.in spacing, 0.0in posts. Table. Jumper Functions and Default Settings JUMPER SETTINGS DESCRIPTION JU D JU CTYP JU UOK JU UOK JU Indicator LED D off Indicator LED D on Disconnect CTYP output from indicator LED D Connect CTYP output to indicator LED D Disconnect UOK output to indicator LED D Connect UOK output to indicator LED D Disconnect UOK output and LED D Connect UOK output to indicator LED D - Connect to -* Connect to GND 9-87; Rev 0; /
2 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 Table. Jumper Functions and Default Settings) (continued) JUMPER SETTINGS DESCRIPTION JU - Connect FSUS to FSUS -* Connect FSUS to GND JU7 Disconnect from R0 (Pullup) Connect to R0 (Pullup) JU8 - Connect THM to R THM - Connect THM to R JU9 Disconnect from R (Pullup) Connect to R (Pullup) JU0 Disconnect INT from R (Pullup) INT Connect INT to R (Pullup) JU Disconnect from VMC VMC Connect to VMC JU Disconnect from C0 Connect to C0 Disconnect from Q JU Connect to Q -, - JU JU UOKEXT JU LED Disconnect from Q Connect to Q -* Connect UOKEXT to Q - Connect UOKEXT to JU (UOK) Disconnect from indicator D LED Connect to indicator D LED Digital Inputs and Outputs The bias for the logic inputs and the open-drain indicators can be provided from the VMC pin of J connector or from the pins and of J. Install jumper JU to use VMC for the supply. The UOK, UOK, INT, CTYP open-drain outputs use supply for their respective pullup voltages. Jumpers JU JU connect the indicator LEDs D D to these open-drain flags. LED pin is another open-drain output, the status of which is reflected by indicator D when JU is installed. UOK/EXT pin is preconfigured by factory as either UOK or EXT. EXT is a push-pull output used to control the external pmos load switch Q. When charger is not present, EXT is high and Q connects to. Connect JU accordingly based on which function UOK/EXT is preconfigured to. and FSUS are digital inputs set by JU and JU. determines if the current limit is fixed at 00mA or controlled by IC settings (IBusLim, ILimSet, IBusDetSw bits); FSUS, if pulled high, forces the input current limit to 0A USB Inferface The MAX7 provides an integrated USB.0 full-speed interface (Mbps). This interface is accessed through the Micro-USB type-b connector, J and type-a connector J. VBUS of J is also the power source for the U. I/O Interface Connector The EV kit allows accessing the digital I/O of the MAX7 individually through three different interface connectors, J, J, and J. Please refer to Table thru Table for the connectors pin description. JU7 Disconnect R from JU (EXT) EXT Connect R to JU (EXT) Table. Aardvark Connector J *Default Position PIN MAX7 DESCRIPTION I C Serial Clock Input GND Ground I C Serial Data Input/Output N.C. Not Connected N.C. Not Connected N.C. Not Connected 7 INT Active-Low Interrupt Output 8 N.C. Not Connected 9 N.C. Not Connected 0 GND Ground Maxim Integrated
3 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 Table. 0-Pin Connector J PIN SIGNAL DESCRIPTION GND Ground VMC.V Supply Input 0 GND Ground Current-Limit Setting Input FSUS Force-Suspend Enable Input 8 INT Active-low Interrupt Output 9 GND Ground I C Serial Data Input/Output I C Serial Clock Input 0 GND Ground All Other Pins N.C. Not Connected Table. PMOD Connector J PIN MAX7 DESCRIPTION FSUS Force-Suspend Enable Input N.C. Not Connected I C Serial Clock Input I C Serial Data Input/Output GND Ground.V Digital Input/Output Supply 7 Current-Limit Setting Input 8 INT Active-Low Interrupt Output 9 N.C. Not Connected 0 N.C. Not Connected GND Ground Digital Interface Supply Ordering Information PART MAX7EVKIT# #Denotes RoHS compliant. TYPE EV Kit Maxim Integrated
4 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 MAX7 EV Kit Bill of Materials ITEM REF_DES DNI/ DNP QTY MFG PART # MFTR VALUE DESCRIPTION TEST POINT; PIN DIA=0.IN; TOTAL LENGTH=0.IN; BOARD HOLE=0.0IN; ORANGE; PHOSPHOR BRONZE WIRE, THM - 0 KEYSTONE N/A SILVER PLATE FINISH; _MON, _MON - 0 KEYSTONE N/A TEST POINT; PIN DIA=0.IN; TOTAL LENGTH=0.IN; BOARD HOLE=0.0IN; WHITE; PHOSPHOR BRONZE WIRE SILVER PLATE FINISH; C, C-C8 - C00XR0-0KNP; EMK07BJ0KA; C08XRC0K; GRM88RC0K VENKEL LTD./TAIYO YUDEN/TDK/M URATA UF C-C - CLB0KOHNNN SAMSUNG ELECTRONIC S 0UF MURATA; GRMBR7H0KA; SAMSUNG CLB0KBFNNNE; ELECTRONIC C0X7RH0K08AC; S; TDK; TAIYO C9 - UMKB70KG YUDEN UF C0 - T9D7K0AT KEMET 7UF 7 C - CLBKBHNNN SAMSUNG ELECTRONIC S 8 VB, CAP, - 00 KEYSTONE N/A 9 D-D, D - PG0W 0 D - SML-LX0IW.UF STANLEY ELECTRIC CO PG0W LUMEX OPTOCOMPO NENTS INC SML-LX0IW CAPACITOR; SMT; 00; CERAMIC; uf; V; 0%; XR; - degc to + 8degC; 0 +/-% degc MAX.USE 0-000u- FOR NEW DESIGN CAPACITOR; SMT (0); CERAMIC CHIP; 0UF; V; TOL=0%; TG=- DEGC TO + DEGC; TC=X7R CAPACITOR; SMT (080); CERAMIC CHIP; UF; 0V; TOL=0%; TG=- DEGC TO + DEGC; TC=X7R CAPACITOR; SMT (7); TANTALUM CHIP; 7UF; V; TOL=0%; MODEL=T9 SERIES CAPACITOR; SMT (0); CERAMIC CHIP;.UF; 0V; TOL=0%; TG=- DEGC TO + DEGC; TC=X7R TESTPOINT WITH.80MM HOLE DIA, RED, MULTIPURPOSE; DIODE; LED; 0W SERIES; GREEN; SMT (0); VF=.V; IF=0.0A DIODE; LED; NM RED LED; MILKY WHITE DIFFUSED LENS; RED; SMT (0); VF=V; IF=0.A J - ZX-B-PA J HIROSE ELECTRIC CO LTD. ZX-B-PA TE CONNECTIVIT Y 08- CONNECTOR; FEMALE; SMT; USB MICRO B-TYPE; BOTTOM MOUNT; RIGHT ANGLE; PINS; -0 DEGC TO +8 DEGC; WITH OPTION TO CONNECT SHIELD PINS CONNECTOR; MALE; THROUGH HOLE; AMP LATCH LOW PROFILE HEADER; STRAIGHT; 0PINS J MILL-MAX J - SBH-PBPC-D0-ST-BK SULLINS ELECTRONIC S CORP. J - TSW-0-08-S-D-RA SAMTEC EVKIT_STANDOFF_- J-J9-0_/? SBH-PBPC- D0-ST-BK TSW-0-08-S- D-RA EVKIT_STAND OFF_-0_/ CONNECTOR; FEMALE; THROUGH HOLE; USB RECEPTACLE; 89 SERIES; RIGHT ANGLE; PINS CONNECTOR; MALE; THROUGH HOLE; HEADER CONNECTOR; STRAIGHT; 0PINS CONNECTOR; THROUGH HOLE; DOUBLE ROW; RIGHT ANGLE; PINS; KIT; ASSY-STANDOFF/IN; PC. STANDOFF/FEM/HEX/- 0/(/IN)/ALUMINUM; PC. SCREW/PHL/PAN/-0/(/8IN)/8-8 STAINLESS STEEL Maxim Integrated
5 Maxim Integrated Evaluates: MAX7/MAX77 MAX7 Evaluation Kit MAX7 EV Kit Schematics ZX-B-PA 800-0HLF 800-0HLF 0 0UF MAX7EWA HLF.9K 800-0HLF VBUS 800-0HLF 0 PG0W 00.K 0UF 00.9K 800-0HLF RRL0P DNI 0.9K UF.9K NC7WZ07PX UF UF NC7WZ07PX.9K VBUS.9K 0 7UF 0 0UF 799-0HLF SML-LX0IW PG0W 800-0HLF 00K PG0W 800-0HLF PG0W RRL0P HLF 800-0HLF.9K UF.UF 799-0HLF HLF UF 800-0HLF 00K 0UF 800-0HLF 0K 800-0HLF J JU0 JU J R JU8 R JU7 JU C R R JU C7 J C C9 JU JU _MON _MON JU JU JU JU9 JU7 R R0 TP9 CAP J0 TP8 TP7 TP C0 D R9 C C TP U THM R JU Q C8 VB Q SFOUT R C C JU JU C R8 R U D D R R7 R R D D U TDP TDN SFOUT CDN LED LED NVP TDP UOK INTB ID VB CDP VB CAP TDN UOK THM UOK CTYPB UOK UOK_EXT UOK_EXT CTYPB FSUS CDN CDP EXT SFOUT CAP B A D C C E E B A C C D D D A E C B D E B B A E A GND VB THM UOK/EXT LED SFOUT FSUS VB CDN NVP INT TDP GND TDN CAP UOK CDP CTYP SHIELD A A Y GND VCC Y SHIELD + S D G S D G A A Y GND VCC Y
6 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 MAX7 EV Kit Schematics (continued) J SBH-PBPC-D0-ST-BK JU 800-0HLF R D PG0W VMC FSUS INTB J 08- INTB AARDVARK INTERFACE J TSW-0-08-S-D-RA INTB J-7 J-8 J-9 J-0 J- J- J- J- J- J- J- J- FSUS Maxim Integrated
7 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 MAX7 EV Kit PCB Layouts MAX7 EV Kit Top Silkscreen MAX7 EV Kit Top MAX7 EV Kit Internal Maxim Integrated 7
8 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 MAX7 EV Kit PCB Layouts (continued) MAX7 EV Kit Bottom Silkscreen MAX7 EV Kit Bottom MAX7 EV Kit Internal Maxim Integrated 8
9 MAX7 Evaluation Kit Evaluates: MAX7/MAX77 Revision History REVISION NUMBER REVISION DATE DESCRIPTION PAGES CHANGED 0 / Initial release For pricing, delivery, and ordering information, please contact Maxim Direct at , or visit Maxim Integrated s website at. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 0 Maxim Integrated Products, Inc. 9
Evaluates: MAX MAX14874 Evalution Kit. General Description. Quick Start. Features. Recommended Equipment. Procedure
General Description The MAX87 evaluation kit (EV kit) is a fully assembled and tested circuit board that evaluates the MAX87 dual relay/valve/motor driver The EV kit operates from a single.5v to 6V supply
MAX40200 Evaluation Kit. Evaluates: MAX40200 Ideal-Diode in a 4-Bump WLP. General Description. Features
General Description The MAX40200 evaluation kit (EV kit) provides a proven design to evaluate the MAX40200 ideal-diode. This EV kit demonstrates the MAX40200 in a tiny, space-saving 4-bump wafer-level
Evaluates: MAX14775E/MAX14776E. MAX14775E Evaluation Kit. General Description. Features. Quick Start. Startup Procedure. Required Equipment
Click here for production status of specific part numbers. MAX4775E Evaluation Kit Evaluates: MAX4775E/MAX4776E General Description The MAX4775E evaluation kit (EV kit) is a fully assembled and tested
Evaluates: MAX MAX40007 Evaluation Kit. Procedure. General Description. Features. Quick Start. Required Equipment
General Description The MAX47 evaluation kit (EV kit) is a fully assembled and tested circuit board that contains all the components necessary to evaluate the MAX47 IC, offered in a space-saving 1.1mm
Evaluates: MAX38903A/MAX38903B. MAX38903 TDFN Evaluation Kit. Quick Start. General Description. Features. MAX38903 TDFN EV Kit Files
Click here for production status of specific part numbers. General Description The MAX38903 TDFN evaluation kit (EV kit) evaluates the MAX38903A/MAX38903B IC family of low noise linear regulators. The
R1 R4, R15, R21 R24, R35 R5 R8, R11, R12, R25 R28, R31, R32 R9, R10, R29, R30 R13, R14, R33, R34 TP1, TP3, TP5, TP6, TP11, TP21, TP26, TP31
MAX/MAX7 Evaluates: MAX/MAX7 General Description The MAX/MAX7 evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the MAX/MAX7 charger detectors. The EV kit features
Evaluates: MAX MAX17290 Evaluation Kit. General Description. Quick Start. Features. Required Equipment. Output Testing
MAX790 Evaluation Kit Evaluates: MAX790 General Description The MAX790 evaluation kit (EV kit) is a fully assembled and tested PCB that contains a 6W DC-DC boost converter for battery-operated, harsh environment,
Evaluates: MAX MAX14914 Evaluation Kit. General Description. Features. MAX14914 EV Kit Board Photo
General Description The MAX494 evaluation kit (EV kit) provides a proven design to evaluate the MAX494, a configurable industrial digital output driver/digital input. The EV kit allows controlling of the
Evaluates: MAX MAX38888 Evaluation Kit. Quick Start. General Description. Features. MAX38888 EV Kit Files. Required Equipment.
Click here for production status of specific part numbers. MAX8888 Evaluation Kit Evaluates: MAX8888 General Description The MAX8888 evaluation kit (EV kit) evaluates the MAX8888 IC. The MAX8888 is a super
S Fully Assembled and Tested
19-5591; Rev 0; 10/10 MAX9626 Evaluation Kit General Description The MAX9626 evaluation kit (EV kit) provides a proven design to evaluate the MAX9626 low-noise, lowdistortion, and high-bandwidth differential
Evaluates: MAX17220 MAX MAX17222 Evaluation Kit. Quick Start. General Description. Features. Detailed Description of Hardware
MAX7 Evaluation Kit Evaluates: MAX7 MAX75 General Description The MAX7 evaluation kit (EV kit) evaluates the MAX7 MAX75 IC family of ultra-low quiescent current step-up DC-DC converters. The MAX7 EV kit
MAX17222 Evaluation Kit Evaluates: MAX17220 MAX17225 General Description Quick Start Required Equipment Procedure
MAX7 Evaluation Kit Evaluates: MAX7 MAX75 General Description The MAX7 evaluation kit (EV kit) evaluates the MAX7 MAX75 IC family of ultra-low quiescent current step-up DC-DC converters. The MAX7 EV kit
+Denotes lead-free and RoHS compliant.
19-4165; Rev 0; 6/08 MAX9921 Evaluation Kit General Description The MAX9921 evaluation kit (EV kit) is a fully assembled and tested PCB that demonstrates the capabilities of the MAX9921 dual 2-wire Hall-effect
Evaluates: MAX17612C 4.5V to 60V, 250mA, Current-Limiter with Reverse Protection. MAX17612C Evaluation Kit. Quick Start. General Description.
Click here for production status of specific part numbers. General Description The MAX76C evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the MAX76C 4.5V to 60V,
Evaluates: MAX38902A/B/C/D. MAX38902 Evaluation Kit. MAX38902 EV Kit Files. General Description. Quick Start. Features. Required Equipment
Evaluates: MAX890A/B/C/D General Description The MAX890 evaluation kit (EV kit) evaluates the MAX890A/B/C/D IC family of low noise linear regulators. The MAX890 EV kit features two independent circuits
Evaluates: MAX MAX17244 Evaluation Kit. General Description. Quick Start. Features. Table 1. EN Configuration (JU1)
General Description The MAX744 evaluation kit (EV kit) demonstrates the MAX744 high-voltage, current-mode step-down converter with low operating current. The EV kit operates over a wide 6V to 36V input
S 5.5V to 18V Operating Voltage Range S Up to 60V Fault Protection S Features Two On-Board 2-Wire Hall-Effect Sensors
19-5062; Rev 0; 11/09 MAX9621 Evaluation Kit General Description The MAX9621 evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the MAX9621 dual, 2-wire Hall-effect
Evaluates: MAX2248. MAX2248 Evaluation Kit. General Description. Features. EV Kit Photo
General Description The MAX2248 evaluation kit (EV kit) simplifies evaluation of the MAX2248 power amplifier (PA). It enables testing of the device s RF performance and requires no additional support circuitry.
Evaluates: MAX17681A for Isolated +24V Output Configuration. MAX17681A Evaluation Kit. General Description. Quick Start. Features
General Description The MAX768AEVKITF is a fully assembled and tested circuit board that demonstrates the performance of the MAX768A high-efficiency, iso-buck DC-DC Converter. The EV kit operates over
Evaluates: MAX MAX31840 Evaluation Kit. Quick Start. General Description. Features. Required Equipment. Procedure. Test with AC or DC Source
General Description The MAX3840 evaluation kit (EV kit) demonstrates the MAX3840 LED driver IC used for dimmable V MR6 as well as AR and other V lighting applications. The EV kit is configured in a boost
+Denotes lead(pb)-free and RoHS compliant. JU1 JU4 4
19-4381; Rev 0; 11/08 General Description The MAX8844Z evaluation kit (EV kit) is a fully assembled and tested PCB for evaluating the MAX8844Z/ MAX8844Y 28V linear Li+ battery chargers. The MAX8844Z EV
Evaluates: MAX17612A 4.5V to 60V, 250mA, Current-Limiter with OV, UV, and Reverse Protection. MAX17612A Evaluation Kit.
Click here for production status of specific part numbers. General Description The MAX76A evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the MAX76A 4.5V to 60V,
Evaluates: MAX MAX16935 Evaluation Kit. General Description. Features and Benefits. Quick Start. Table 1. EN Configuration (JU1)
General Description The MAX16935 evaluation kit (EV kit) demonstrates the MAX16935 high-voltage, current-mode step-down converter with low operating current. The EV kit operates over a wide 3.5V to 36V
Evaluates: MAX17682 for Isolated +12V Output Configuration. MAX17682 Evaluation Kit. General Description. Quick Start. Features. Recommended Equipment
General Description The MAX7 EV kit is a fully assembled and tested circuit board that demonstrates the performance of the MAX7 high-efficiency, iso-buck DC-DC Converter. The EV kit operates over a wide
Evaluates: MAX MAX44284 Evaluation Kit. General Description. Quick Start. EV Kit Contents. Features and Benefits. Required Equipment.
General Description The MAX44284 evaluation kit (EV kit) provides a proven design to evaluate the MAX44284 high-precision, lowpower, current-sense amplifier. This EV kit demonstrates the MAX44284 in an
MAX16920B Evaluation Kit Evaluates: MAX16920A/MAX16920B
19-5744; Rev 0; 1/11 MAX16920B Evaluation Kit General Description The MAX16920B evaluation kit (EV kit) is an assembled and tested PCB used to evaluate the MAX16920B powermanagement IC for automotive radios,
MAX16929 Evaluation Kit Evaluates: MAX16929
19-5838; Rev 0; 4/11 MAX16929 Evaluation Kit General Description The MAX16929 evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that provides the voltages and features required
General Description. Features. Component List. Component Suppliers
General Description The MAX5062A evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the performance of the MAX5062A 60V, 300mA ultra-small, high-efficiency, synchronous
MAX1757/MAX1758 Evaluation Kits
9-86; Rev 0; 0/00 MAX757/MAX758 Evaluation Kits General Description The MAX757/MAX758 evaluation kits (EV kits) are assembled and tested PC boards that implement a step-down, switching lithium-ion (Li+)
MAX8686 Evaluation Kit Evaluates: MAX8686
General Description The MAX8686 evaluation kit (EV kit) provides a proven design to evaluate the MAX8686 single-phase, highefficiency, 25A, step-down regulator with integrated switches. The device is a
MAX9643 Evaluation Kit Evaluates: MAX9643
General Description The MAX9643 evaluation kit (EV kit) is an assembled and tested PCB used to evaluate the MAX9643 60V, highspeed, precision, unidirectional current-sense amplifier. The EV kit features
+Denotes lead(pb)-free and RoHS compliant
9-44; Rev ; 0/0 MAX890A Evaluation Kit General Description The MAX890A evaluation kit (EV kit) is a fully assembled and tested circuit board for evaluating the A, -cell Li+ DC-DC battery charger. The EV
Features. General Description. Component List
General Description The MAX17502F evaluation kit (EV kit) provides a proven design to evaluate the MAX17502F high-efficiency, highvoltage, synchronous step-down DC-DC converter. The EV kit uses the device
+Denotes lead-free and RoHS compliant.
9-0; Rev 0; 0/07 MAX866 Evaluation Kit General Description The MAX866 evaluation kit (EV kit) is a fully assembled and tested circuit board that evaluates the MAX866 power-management IC. The MAX866 integrates
Maxim Integrated Products 1
19-5287; Rev 0; 5/10 MAX9636 Evaluation Kit General Description The MAX9636 evaluation kit (EV kit) is an assembled and tested PCB used to evaluate the MAX9636 lowpower, low-noise, CMOS input op amp, which
Evaluate: MAX17502E in TDFN Package. MAX17502E Evaluation Kit. General Description. Features. Component List
General Description The MAX17502E evaluation kit (EV kit) provides a proven design to evaluate the MAX17502E high-efficiency, highvoltage, synchronous step-down DC-DC converter. The EV kit uses this device
Maxim Integrated Products 1
19-4920; Rev 0; 8/09 MAX15046B Evaluation Kit General Description The MAX15046B evaluation kit (EV kit) is a fully assembled and tested circuit board that contains all the components necessary to evaluate
MAX8622 Evaluation Kit Evaluates: MAX8622
General Description The MAX8622 evaluation kit (EV kit) is a fully assembled and tested circuit for evaluating the MAX8622 Xenon flash charger. The MAX8622 EV kit operates from a 2.5V to 5.5V supply, and
MAX17498B Evaluation Kit Evaluates: MAX17498B
19-6293; Rev 0; 4/12 MAX17498B Evaluation Kit General Description The MAX17498B evaluation kit (EV kit) is a fully assembled and tested circuit board that contains an isolated 7W flyback DC-DC converter.
Evaluate: MAX17501H in TDFN Package
General Description The MAX17501H EV kit provides a proven design to evaluate the MAX17501H high-efficiency, high-voltage, synchronous step-down DC-DC converter in a TDFN package. The EV kit uses the MAX17501H
S +10V to +14V Input Range S 750kHz Switching Frequency S Output Voltages. S Greater than 94% Efficiency (Step-Up Switching Regulator)
19-5089; Rev 0; 12/09 MAX17122 Evaluation Kit General Description The MAX17122 evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that provides the voltages and features required
MAX3747/MAX3747A Evaluation Kit
19-3297; Rev A; 05/04 MAX3747/MAX3747A Evaluation Kit General Description The MAX3747/3747A evaluation kit (EV kit) simplifies evaluation of the MAX3747/3747A limiting amplifiers. The EV kit enables testing
Maxim Integrated Products 1
9-740; Rev ; /04 General Description The MAX748 evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board that contains a boost switching regulator and two charge-pump voltage-regulator
MAX17020 Evaluation Kit. Evaluates: MAX17020
19-4132; Rev 0; 5/08 MAX17020 Evaluation Kit General Description The MAX17020 evaluation kit (EV kit) demonstrates the MAX17020 s standard application circuit. This dual Quick-PWM synchronous DC-DC converter
C13, C19, C20, C21, C30. Maxim Integrated Products 1
9-456; Rev 0; 0/04 MAX58 Evaluation Kit General Description The MAX58 evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board that contains a step-up switching regulator, a
Maxim Integrated Products 1
19-4002; Rev 2; 12/06 MAX6495 Evaluation Kit General Description The MAX6495 evaluation kit (EV kit) demonstrates a high-voltage overvoltage protection circuit for automotive applications that must survive
S Analog/PWM Input-Charge-Current Setting S Up to 1.2MHz Switching Frequency S Programmable Charge Current Up to 4A S Monitors Input/Outputs
19-4996; Rev 0; 10/09 General Description The MAX17015 evaluation kit (EV kit) is a complete, fully assembled and tested surface-mount PCB that features the MAX17015B highly integrated, multichemistry
MAX16840L Evaluation Kit Evaluates: MAX16840
19-5978; Rev 0; 7/11 MAX16840L Evaluation Kit General Description The MAX16840L low-power (5W input) evaluation kit (EV kit) demonstrates the MAX16840 HBLED driver IC used for Solid State Lighting (SSL)
MAX5986A Evaluation Kit Evaluates: MAX5986A
19-6349; Rev 0; 5/12 MAX5986A Evaluation Kit General Description The MAX5986A evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board featuring an Ethernet port, network powered-device
Evaluates: MAX17497A. MAX17497A Evaluation Kit. Features. General Description. Component List
General Description The MAX17497A evaluation kit (EV kit) demonstrates the MAX17497A controller IC offline AC-DC flyback converter design and features an integrated step-down regulator. The EV kit circuit
MAX6971 Evaluation Kit. Evaluates: MAX6971
9-676; Rev 0; /07 General Description The MAX697 evaluation kit (EV kit) provides a proven design to evaluate the MAX697 6-port, constant-current LED driver. The EV kit also includes Windows 000/XP/Vista
S AC-Coupled I/Os for Ease of Testing S Fully Assembled and Tested S +3.3V Power-Supply Operation S On-Board 25MHz Crystal
19-5065; Rev 0; 12/09 E V A L U A T I O N K I T A V A I L A B L E MAX3677 Evaluation Kit General Description The MAX3677 evaluation kit (EV kit) is an assembled demonstration board that provides convenient
Specifications are at T A = 25 C
Description Demonstration circuit 569 is a single cell Li-Ion linear charger in a SOT-. Charge rates as high as 600mA can be achieved due to the LTC 4054 s internal die temperature control loop that prevents
MAX712 Linear-Mode Evaluation Kit
9-2366; Rev ; /02 MAX72 Linear-Mode Evaluation Kit General Description The linear-mode evaluation kit (EV kit) is a complete battery charger for nickel metal hydride (NiMH) and fast-charge nickel-cadmium
MAX1966 Evaluation Kit. Evaluates: MAX1966/MAX1967
9-; Rev 0; /0 MAX9 Evaluation Kit General Description The MAX9 evaluation kit (EV kit) is a fully assembled and tested circuit board that contains two independent step-down DC-to-DC converter circuits.
MAX17019 Evaluation Kit Evaluates: MAX17019
General Description The MAX17019 evaluation kit (EV kit) presents the MAX17019 high input-voltage quad-output controller in a typical application setup. The EV kit operates from a 5.5V to 38V input range.
Purpose. Table of Contents. Purpose Introduction General Product Information Key Performance Summary Table... 3
Purpose The RT7251B is a high-efficiency current mode synchronous step-down regulator that can deliver up to 1.5A output current from a wide input voltage range of 4V to 17V. This document explains the
SP6644/6645 Evaluation Board Manual
SP6644/6645 Evaluation Board Manual Easy Evaluation for the SP6644/6645 Single or Dual Cell Alkaline to 3.3V Output Provides up to 150mA output current for 2-Cell Input High Efficiency: 92% µsoic Package
QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1020 HIGH EFFICIENCY USB POWER MANAGER + TRIPLE STEP-DOWN DC/DC LTC3555
DESCRIPTION Demonstration Circuit 1020 is a High Efficiency USB Power Manager + Three Step-Down DC/DC Converters featuring the LTC 3555. The LTC 3555 is a highly integrated power management and battery
EV2456-J-00A 0.5A, 50V, 1.2MHz Step-Down Converter Evaluation Board
EV2456-J-00A 0.5A, 50V, 1.2MHz Step-Down Converter Evaluation Board DESCRIPTION The EV2456-J-00A is an evaluation board for the MP2456, a high-voltage step-down regulator with a built-in power MOSFET.
DEMO MANUAL DC705A. LTC4053EMSE-4.2 Lithium-Ion Linear Battery Charger with Thermal Regulation. Description
Description LTC405EMSE-4. Lithium-Ion Linear Battery Charger with Thermal Regulation Demonstration circuit DC705 is a complete constantcurrent, constant-voltage battery charger designed to charge one Lithium-Ion
S AC-Coupled I/Os for Ease of Testing S Fully Assembled and Tested S +3.3V Power-Supply Operation S On-Board 25MHz Crystal SW13, SW15 SW4, SW6,
19-5173; Rev 0; 2/10 E V A L U A T I O N K I T A V A I L A B L E MAX3679A Evaluation Kit General Description The MAX3679A evaluation kit (EV kit) is an assembled demonstration board that provides convenient
DS1321 Flexible Nonvolatile Controller with Lithium Battery Monitor
19-6312; Rev 6/12 Flexible Nonvolatile Controller with Lithium Battery Monitor FEATURES Converts CMOS SRAM into nonvolatile memory Unconditionally write-protects SRAM when V CC is out of tolerance Automatically
EV2636-R-00A Full-Power-Management IC For Single-Cell Battery System
Full-Power-Management IC For Single-Cell Battery System DESCRIPTION The is the evaluation board designed to demonstrate the capabilities of MPS MP2636, a highly-integrated, flexible switch-mode battery
LET9045C. RF power transistor from the LdmoST family of n-channel enhancement-mode lateral MOSFETs. Features. Description
RF power transistor from the LdmoST family of n-channel enhancement-mode lateral MOSFETs Features Excellent thermal stability Common source configuration P OUT (@28 V) = 45 W with 18.5 db gain @ 960 MHz
Power Management Solution With 196 HVC ENYCAP TM for Mini Charger and Fixed Voltage Supply Board
VISHAY BCCOMPONENTS www.vishay.com Aluminum Capacitors By Gerald Tatschl MAL29699003E3 96 HVC ENYCAP TM - MINI CHARGER AND BACKUP BOARD DESCRIPTION The MAL29699003E3 mini charger and backup demonstration
Lithium Ion Battery Charger for Solar-Powered Systems
Lithium Ion Battery Charger for Solar-Powered Systems General Description: The is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries.
1A Linear Li+ Battery Chargers with Integrated Pass FET and Thermal Regulation in 2mm x 2mm TDFN
19-3670; Rev 0; 4/05 EVALUATION KIT AVAILABLE 1A Linear Li+ Battery Chargers with Integrated Pass General Description The intelligent, stand-alone constant-current/constant-voltage (CCCV), thermally regulated
1.2A Single-chip Li-ion and Li-POL Charge
1.2A Single-chip Li-ion and Li-POL Charge General Description The is a complete constant-current / constant-voltage linear charger for single cell lithium-ion batteries. Its ESOP-8 package and low external
Linear Li+ Battery Charger with Integrated Pass FET, Thermal Regulation, and ACOK in 3mm x 3mm TDFN
19-289; Rev 2; 8/5 EVALUATION KIT AVAILABLE Linear Li+ Battery Charger with Integrated Pass FET, General Description The MAX158 is an intelligent, stand-alone constant-current, constant-voltage (CCCV),
BD99954MWV Evaluation Kit
ROHM Battery Charger Solutions BD99954MWV Evaluation Kit Contents Item No. Topic Page No. 1 Introduction 2 1.2 Description 2 1.3 Applications 2 1.4 Features 2 2 Evaluation Board Operating Limits and Absolute
ISL80102, ISL80103 High Performance 2A and 3A LDOs Evaluation Board User Guide
ISL812, ISL813 High Performance 2A and LDOs Evaluation Board User Guide Description The ISL812 and ISL813 are high performance, low voltage, high current low dropout linear regulator specified at 2A and,
140P-2674 AND LATER 175P-4023 AND LATER 250P-2783 AND LATER
SERIAL NUMBERS 140P-2674 AND LATER 175P-4023 AND LATER 250P-2783 AND LATER FORM WC5310 3/95 (Rev. 9/97, 6/99, 1/00, 2/00) Systematics, Inc. 1025 Saunders Ln. West Chester, Pa. 19380 TABLE OF CONTENTS VIEW
Preliminary 2.4GHz FSK/GFSK Transceiver Revision History Rev. History Issue Date Remark 0.0 Initial issue November, 2008 Preliminary MD7105-A
Preliminary 2.4GHz FSK/GFSK Transceiver A7105 module specification MD7105-A08(-01) Important Notice: AMICCOM reserves the right to make changes to its products or to discontinue any integrated circuit
Evaluates: MAX5974C. MAX5974C Evaluation Kit. General Description. Features. EV Kit Efficiency vs. Output Current at V IN = 42V, 48V, and 57V
General Description The MAX5974C evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board featuring the MAX5974C active-clamped, spread-spectrum, current-mode PWM controller
CONSONANCE. 1A LiFePO4 Battery Charger CN3058E. Features: General Description: Applications: Pin Assignment
A LiFePO4 Battery Charger CN3058E General Description: The CN3058E is a complete constant-current /constant voltage linear charger for single cell LiFePO4 rechargeable batteries. The device contains an
PRODUCT DATASHEET AAT3681
General Description The BatteryManager is an integrated single cell lithium-ion/polymer battery charger IC, designed to operate from a DC power source or USB port up to an input voltage of 7.5V. It requires
UT8RHEEB-288PC RadTol Eclipse FPGA UT6325 Evaluation Board Advanced Data Sheet
Standard Products UT8RHEEB-288PC RadTol Eclipse FPGA UT6325 Evaluation Board Advanced Data Sheet September 2008 www.aeroflex.com/fpga FEATURES User configurable evaluation board for the UT6325 RadTol Eclipse
GENERAL DESCRIPTION. FEATURES 6A step-down power module
XR7906 April 06 GENERAL DESCRIPTION The XR7906 is part of a family of 40V synchronous step-down power modules combining the controller, drivers, inductor, passive components and MOSFETs in a single package
CE3152 Series. Standalone Linear LiFePO4 battery charger with Thermal Regulation INTRODUCTION: FEATURES: APPLICATIONS: PIN CONFIGURATION:
Standalone Linear LiFePO battery charger with Thermal Regulation Series INTRODUCTION: The is a complete constantcurrent constantvoltage linear charger for single cell LiFePO batteries. It s SOT package
800mA Linear Li-Ion Battery Charger with Protection of Reverse Connection of Battery
800mA Linear Li-Ion Battery Charger with Protection of Reverse Connection of Battery General Description The is a complete constant-current/constant- voltage linear charger for single cell lithium-ion
Silver T E L E C O M. 1. Features. 2. Description. IEEE802.3af compliant. Small SIL package size - 56mm (L) x 14mm (H) Low output ripple and noise
Silver T E L E C O M V2.0 Aug 2008 Pb. Features IEEE802.3af compliant Small SIL package size - 56mm (L) x 4mm (H) Low output ripple and noise Input voltage range 36V to 57V Only one low cost external decoupling
L, LTC, LTM, LT, Burst Mode, are registered trademarks of Linear Technology Corporation.
DESCRIPTION Demonstration circuits 1376A-A and 1376A-B are High Efficiency USB Power Manager + Triple Step Down DC/DC featuring the LTC3555-1 and LTC3555-3 respectively. The LTC 3555-1/LTC3555-3 are highly
Speedster22i Capacitor User Guide UG051 April 10, 2015
Speedster22i Capacitor User Guide UG051 April 10, 2015 UG051, April 10, 2015 1 Copyright Info Copyright 2015 Achronix Semiconductor Corporation. All rights reserved. Achronix is a trademark and Speedster
LM3352 Regulated 200 ma Buck-Boost Switched Capacitor DC/DC Converter
Regulated 200 ma Buck-Boost Switched Capacitor DC/DC Converter General Description The LM3352 is a CMOS switched capacitor DC/DC converter that produces a regulated output voltage by automatically stepping
ZSPM401x Application Note - Circuit Layout and Component Selection Contents
ZSPM401x Application Note - Circuit Layout and Component Selection Contents 1 Introduction... 2 2 Typical Application Schematic... 2 3 Printed Circuit Board (PCB) Layout Guidelines... 3 4 Recommended Bill
1.2A Single-chip Li-ion and Li-POL Charge
1.2A Single-chip Li-ion and Li-POL Charge General Description The LP28012 is a complete constant-current/ constant voltage linear charger for single cell lithium-ion batteries. Its ESOP8 package and low
Product Guide: Series III Pump Control Board Set (RoHS)
revised 04/08/10 Description: The Series III Pump Control Board Set provides motor drive and pump control for a wide assortment of pumps from Scientific Systems, Inc. The assembly consists of two circuit
Silvertel. Ag Features. 2 Description. Power-Over-Ethernet Module. IEEE802.3af compliant. Small SIL package size - 56mm (L) x 14mm (H) Low cost
Silvertel V2.5 Feb 2014 Datasheet Pb 1 Features IEEE802.3af compliant Small SIL package size - 56mm (L) x 14mm (H) Low cost Input voltage range 36V to 57V Minimal (low cost) external components required
Assembly Manual for New Control Board 22 June 2018
Assembly Manual for New Control Board 22 June 2018 Parts list Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 9 104 capacitors 1 Rotary encode with switch 1 5-volt regulator
i3a Evaluation Board Manual
i3a Evaluation Board Manual TDK Lambda Evaluation Board P/N i3a5a8a-00-evk-dpp Table of Contents Getting Started with the i3a Before Using the Eval Board...3 Device Introduction... 4 Evaluation Board Introduction
ACE4108 Max.2A Li-ion Switching Charger IC
Description The ACE4108 is a 2A Li-Ion battery switching charger intended for 12V. Low power dissipation, an internal MOSFET and its compact package with minimum external components requirement makes the
CONSONANCE. 1A Nickel-Metal Hydride Battery Charger IC CN3085. General Description: Features: Pin Assignment. Applications:
A Nickel-Metal Hydride Battery Charger IC CN3085 General Description: CN3085 is a charger IC for single to four cell Nickel Metal Hydride (NiMH) batteries. The device contains an on-chip power MOSFET and
Silvertel. Ag Features. Multi-Stage Charging. Battery Reversal Protection. Reduced Power Consumption. Wide DC or AC Input Voltage Range
Silvertel V1.1 October 2012 Pb 1 Features Multi-Stage Charging Battery Reversal Protection Reduced Power Consumption Wide DC or AC Input Voltage Range High Efficiency DC-DC Converter Programmable Charge
ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]
![ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]](/thumbs/90/103906919.jpg "ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]")
ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1] ez1081pre Colourbook Contents. Section 1 - Colourbook assembly guide Section 2 - Setup and Calibration Section 3 - Schematics diagrams and
Silvertel. Ag Features. 2. Description. Power-Over-Ethernet Module. IEEE802.3af compliant. Small SIL and SMT package available
Silvertel V2.2 Jan 2015 Datasheet Ag9700 Pb 1. Features IEEE802.3af compliant Small SIL and SMT package available Low cost, with minimal external components required Input voltage range 36V to 57V Short-circuit
Li-ion/Li Polymer Battery Charger. Features
General Description The is a highly-integrated battery charger for single-cell Li-ion or Li-polymer batteries capable of operating with an input voltage reached 2.5V. It is a complete charger device designed
APPLICATION NOTE. Thermobility WPG-1. Thermoelectric Energy Harvesting System
Thermobility Thermoelectric Energy Harvesting System Table of Contents Introduction... 3 Thermoelectric Energy Harvesting... 3 Thermobility Design... 6 How to Use the... 7 Application Example: Wireless
Silvertel. Ag Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W peak output power
Silvertel V.3 April 207 Datasheet Pb Features IEEE802.3at and IEEE802.3af compliant Maximum 30W peak output power Small Single In-Line (SIL) package size 57.3mm (L) x 4mm (H) Overload, short-circuit and
PID-1500 THERMOELECTRIC & RESISTIVE HEATER TEMPERATURE CONTROLLER INSTRUCTION MANUAL
LASER DIODE DRIVERS TEMPERATURE CONTROLLERS Simply Advanced Control for Your Cutting Edge Design PID-1500 THERMOELECTRIC & RESISTIVE HEATER TEMPERATURE CONTROLLER INSTRUCTION MANUAL P O Box 865, Bozeman,