NAZIV VZDRŽEVALNE ORGANIZACIJE SKLIC ODOBRITVE VZDRŽEVALNE ORGANIZACIJE DELO DO. DELO POTRJUJE (ime in priimek odgovorne osebe)

Transcription

1 Vrednotenje delovnih izkušenj za kategorijo B1.1 PODATKI O KANDIDATU IME kandidata PRIIMEK kandidata DATUM rojstva NASLOV stalnega prebivališča ZAPOSLITVE NAZIV VZDRŽEVALNE ORGANIZACIJE NAZIV VZDRŽEVALNE ORGANIZACIJE NAZIV VZDRŽEVALNE ORGANIZACIJE SKLIC ODOBRITVE VZDRŽEVALNE ORGANIZACIJE SKLIC ODOBRITVE VZDRŽEVALNE ORGANIZACIJE SKLIC ODOBRITVE VZDRŽEVALNE ORGANIZACIJE DELO OD DELO DO DELO OD DELO DO DELO OD DELO DO DELO POTRJUJE (ime in priimek odgovorne osebe) DELO POTRJUJE (ime in priimek odgovorne osebe) DELO POTRJUJE (ime in priimek odgovorne osebe) DATUM potrditve PODPIS odgovorne osebe DATUM potrditve PODPIS odgovorne osebe DATUM potrditve PODPIS odgovorne osebe Raba angleškega jezika za opis opravila izvira iz določila 66.A.20(b), ki pravi, da imetnik licence za vzdrževanje ne sme izvajati svojih pravic, če ni sposoben do ravni razumevanja brati, pisati in komunicirati v jezikih, v katerih so tehnična dokumentacija in postopki, potrebni za spremljanje izdaje potrdila o sprostitvi v uporabo. Stran 1 od 19

2 podpis hour check (general aviation aircraft) Review records for compliance with airworthiness directives Review records for compliance with component life limits Procedure for Inspection following lightning strike Perform symmetry check Locate component's by station number Assist in : Jack complete aircraft Assist in : Sling or trestle major component Assist in : Jack aircraft nose or tail wheel Check aircraft against equipment list Level aircraft Prepare weight and balance amendment Weigh aircraft Tow aircraft Be part of aircraft towing team. Stran 2 od 19

3 podpis Tie down aircraft Park, secure and cover aircraft Position aircraft in dock Check aircraft for correct placards Check aircraft for correct markings Check tire pressures AMC145.A.30g.2q Removal / closure of panels, cowls or covers Check accumulator pressure Check hydraulic fluid level Perform pre-flight/daily check Grease aircraft Check oil level Refuel aircraft Charge oleo Windows & transparencies cleaning and polishing Stran 3 od 19

4 podpis Connect ground power Defuel aircraft Application of one / two component sealers and compounds Check operation of air conditioning/heating system Troubleshoot faulty system Check operation of radios Adjust voltage regulator AMC145.A.30g.2m Replace aircraft main and APU aircraft batteries Troubleshoot faulty system Amend electrical load analysis report Replace circuit breakers Replace generator/alternator Charge Ni-Cad battery Generator power check / voltage adjustment Operational check of ground power. Stran 4 od 19

5 podpis Repair/replace electrical feeder cable Replace switches Check seats/belts for security Change cabin configuration Check emergency equipment Replace passenger seats Replace crew seats Replace carpets AMC145.A.30g.2c Replace emergency equipment Check ELT for compliance with regulations Check fire bottle contents Check operation of warning system Troubleshoot faulty system Inspect engine fire wire detection systems Check for correct assembly and locking. Stran 5 od 19

6 podpis Install control cable and fittings Troubleshoot faulty system Flight control rigging Check control range and sense of movement Adjust control cable tension Adjust trim tab Replace booster pump Check filters Check fuel system Check calibration of fuel quantity gauges Troubleshoot faulty system Fuel quantity indicating system functional testing Check operation of systems Troubleshoot faulty system Replace timer. Stran 6 od 19

7 podpis Troubleshoot faulty system Replace master caution unit Bleed brakes Troubleshoot faulty system Charge struts Replace brake control valve Replace shock strut seals Replace nose/tail wheel Repair/replace navigation lights Repair/replace interior lights Check pitot static system for leaks Check calibration of pitot static instruments Compass / Standby Compass compensation swing and calculation Treat corrosion Apply protective treatment. Stran 7 od 19

8 podpis Sheet metal repair Fiber glass repair Troubleshoot faulty system Rig/adjust locking mechanism Replace windshield Replace window Repair transparency Skin repair Replace Check incidence/rig Perform static functional checks Troubleshoot faulty system Dynamically balance prop Dress out blade damage Check operation during ground run. Stran 8 od 19

9 podpis Adjust governor Replace governor Replace propeller Assemble prop after transportation Check track Build up ECU Replace engine Repair cowling Troubleshoot t Establish reference power t Hot section inspection t Engine ground run t Troubleshoot t Troubleshoot faulty system t Replace engine driven pump. Stran 9 od 19

10 podpis t Clean/test fuel nozzles t Adjust FCU t Clean/replace filters t Replace FCU t Check glow plugs / igniters t Check H.T. leads t Check ignition unit t Replace ignition unit t Troubleshoot faulty system Rig mixture HP cock lever Troubleshoot faulty system Check controls for range and sense of operation Rig power lever Rig RPM control Rig thrust lever. Stran 10 od 19

11 podpis Check controls for correct assembly and locking Replace engine instruments Replace thermocouples Check calibration Troubleshoot faulty system Perform oil dilution Replace oil pump Troubleshoot faulty system Replace oil cooler Change oil Check filters Replace firewall shut off valve Replace starter Replace start relay Replace start control valve. Stran 11 od 19

12 podpis Check cranking speed Troubleshoot faulty system Adjust density controller Troubleshoot faulty system Replace water/methanol pump Check chip detector Replace gearbox Replace drive shaft M 7. 1 Safety precautions when using fluids, gasses and chemicals. M 7. 2 Use basic tool tools and equipment for: cutting, forming, and joining commonly used materials. M 7. 5 Reading and interpretation of electrical schematic and wiring diagram. M 7. 5 Identify standards and specifications of common use parts i.e. nuts, bolts, washers, and split pins. M 7. 5 Interpret and work to engineering drawings. M 7. 6 Fit and remove thread inserts. M 7. 6 Select and use feeler, slip, limit, go / no go gauges. Stran 12 od 19

13 podpis M 7. 6 Drill and ream perpendicular holes in ferrous and non-ferrous material M 7. 6 Mark out use measuring equipment e.g.:micrometers,rulers,verniers,height gauges,squares,vee blocks. M 7. 6 Use a range of hand tools and power tools to achieve accuracy of + - 0,01in / 0.25mm. M 7. 6 Related safety practices. M 7. 6 Drill and tap threaded hole. M 7. 7 Prepare, and install a simple loom, using at least two binding methods. M 7. 7 Inspection of electrical cable looms / bundles and cable trucking. M 7. 7 Insertion / extraction of electrical inserts in a variety of electrical connectors. M 7. 7 Explain / demonstrate how to inspect aircraft areas for HIRF protection. M 7. 7 Discuss and demonstrate the use of range of test meters to measure amps, volts and resistance. M 7. 7 Carry out basic fault finding techniques using a range of test meters. M 7. 7 Check an aircraft electrical circuit for continuity against electrical wiring diagram. M 7. 7 Solder cables to single and mulin connectors / tag boards. M 7. 7 Prepare cable ends or plug socket terminals, using crimping tools. M 7. 7 Using at least two crimping system, select appropriate cable crimping tools and crimp cables. Stran 13 od 19

14 podpis M 7. 7 Select and use appropriate cable stripping tools. M 7. 7 Identify a range of electrical component symbols. M 7. 7 Identify cable and cable values by reference to the maintenance manuals. M 7. 7 Carry out bonding and insulation tests. M 7. 7 Interpret typical electrical wiring diagrams and schematics circuits. M 7. 9 Remove and replace a range of flexible hoses including clips and brackets. M 7. 9 Remove and replace a range of rigid pipes, including clips and brackets. M 7.11 Lubrication of bearings, flight controls and undercarriages. M Select and install oversize rivets as instructed in SRM. M Remove defective rivets without causing further damage to skin. M Shape aluminum alloy to achieve + - 0,5 x of bend angle, + - 0,030 ins / 0,075 mm M Set a range of other fasteners in aluminum sheet. M Identify a range of solid and blind rivets and fasteners. M Select and fit sheet gripping pins. M Select and use a range of appropriate rivet closing tools. Stran 14 od 19

15 podpis M Set a range of rivets in aluminum sheet. Range to include raised and countersunk rivets. M Removal of corrosion and applying the protection of aluminum sheet metal. M Identify, select and use a range of rivet setting equipment. M Cut and shape material to required profile, finish edges and deburr using approved procedures. M Identify rivet setting faults. M Use a range of hand & power tools to position rivet holes to an acc ,30in / 0,75mm. M Interpret engineering drawings and calculate size of material to produce component with more bends. M Use a range of hand tools, folding and bending machines, guillotine to shape aluminum alloy. M Bend metal to bend a radius, angle and dimensions as in the engineering drawing. M Identification of sealing and bonding agents. M Repair of composite and non-metallic materials and structures. M Detection of defects / deterioration in composite and non-metallic material. M Identification of the characteristic and properties of common composite materials. M 7.17 Awareness of hazards when working with A/C - noise,heat,moving surfaces,propellers,intakes,exhausts. M 7.18 Inspect engine using boroscope. Stran 15 od 19

16 podpis 211 M 7.18 Identification of a range of materials M 7.18 Use at least of the one of the following NDT procedure: dye penetrant or florescent dye. M 7.18 Inspection of a structure using a mirror and a light source. M 7.18 Measure shafts,bores,flanges,and adjacent surfaces using precision measuring instr. & record dim. M 7.18 Demonstrate competence when wire locking a variety of assemblies. M 7.18 Fit and remove a range of components e.g.:split pins,tabs,spring and plain washers,plain&lock nuts. M 7.18 Identify part numbers and serial numbers from an approved component overhaul manual or IPC. M 7.18 Adjust, set and use torque spanners. M 7.18 Cleaning and contamination control M 7.18 Apply correct procedures: Material storage and handling M 7.18 Use of a range of common assembly and disassembly tools plus specific application tools. M 7.19 Carry out turbulence check. M 7.20 Replace oleo seals. M 7.20 Certification / release procedure. Stran 16 od 19

17 podpis Stran 17 od 19

18 podpis Stran 18 od 19

19 podpis Primer pravilno izpolnjene vrstice izvedbe ATA 100 kratek opis izvedene naloge MG-21 S5-ZIJ Composite structure inspection with coin tapping 20 I B vzdr. podpis nadzornika 20 - poglavje M7 - modul I - izvedba O - opazovanje OPOMBA: Vsebina dnevnika je skladna z AMC 66.A.20(b)2. L - linijsko vzdrževanje B - vzdrževanje v bazi Stran 19 od 19