1. SPECIFICATIONS OF LAMPS

Size: px

Start display at page:

Download "1. SPECIFICATIONS OF LAMPS"

Annabelle Townsend
5 years ago
Views:

1 SPECIFICATIONS OF LAMPS Exterior Lamps Description Numbers GEN EU Headlamp High beam 2 55W 55W/15W Front combination lamp Outside turn signal lamp (supplemental turn signal lamp) Rear combination lamp High mounted stop lamp Low beam 2 55W 55W Tail/Position lamp 4 LED LED Front fog lamp 2 35W 35W Turn signal lamp 2 21W 21W 10 LED LED Stop lamp (Upper) 32 LED LED Stop lamp (Lower) 24 LED Tail lamp 16 LED LED Turn signal lamp 2 21W 21W Backup lamp 2 16W 16W Rear fog lamp 2 21W Stop lamp 18 LED LED High mounted stop lamp 2 16W 16W Interior Lamps Description Specification Numbers Front room lamp 10W 2 Glove box lamp 10W 1 Center room lamp 10W 1 Rear room lamp 10W 1 Door courtesy lamp 5W 4 Sun visor lamp 0.15A 2

2 SPECIFICATIONS OF AUTO LIGHT Description Specification Operating voltage 9V ~ 16V Load Maximum 200 ma (relay load) Operating temperature 30 ~ 85 Operating temperature 40 ~ ±120 Location Top center of inner side of windshield glass In vehicle for EU market, the auto light function is not available. LED The LED stands for "Light Emitting Diode" or "Luminescent Diode." LED is a semiconductor diode that emits incoherent narrowspectrum light when electrically biased in the forward direction of the pn junction, as in the common LED circuit. In short, it is an element that converts electric signals into light signals. Yellow, blue, red and white LEDs are currently available. The followings are the advantages of LED. It is not glaring and doesn't have short circuit unlike the conventional lamps. It is semipermanent and doesn't generate heat. Its power consumption is much lower than those of conventional bulbs. Luminous Intensity Luminous intensity is a measure for the amount of light which passes through the unit area per time unit. The SI unit of luminous intensity is the candela (cd), an SI base unit. Luminance Luminance describes the amount of light that passes through or is emitted from a particular area, and falls within a given solid angle. It is measured in stilb (sb) or nit (nt). Intensity of illumination This indicates the amount of light reaching a given area. Measuring unit is lux (lx) and it is not directly proportional to the brightness of the area as the reflection rate is not included.

High beam Low beam High beam Low beam Turn

3 MAJOR CHANGES Front Side Head Lamp Old New High beam Low beam High beam Low beam Turn signal/tail lamp Tail lamp Changed the head lamp design and functions. Deleted the turn signal lamp and changed the tail lamp to LED type from bulb type. Front Combination Lamp Old New Fog lamp Fog lamp Turn signal lamp Integrated the fog lamp and turn signal lamp.

106 Rear Side Changed the design of reflex reflector Rear Combination Lamp Old New Tail/Stop lamp Stop lamp Tail lamp Tail lamp Backup lamp Turn signal lamp Backup lamp

4 106 Rear Side Changed the design of reflex reflector Rear Combination Lamp Old New Tail/Stop lamp Stop lamp Tail lamp Tail lamp Backup lamp Turn signal lamp Backup lamp Turn signal lamp Stop lamp Rear fog lamp (EU) Changed the design and functions of rear combination lamp. Changed the stop lamp and tail lamp to LED type from bulb type.

5 Others Outside Turn Signal Lamp Old New Outside turn signal lamp Introduced new outside turn signal lamp (LED type). Side Repeater Lamp Deleted the side repeater lamp.

108 1. EXTERIOR LAMPS 1) Overview The exterior lamps consist of front lamps, rear lamps and side lamps.

mounted stop lamp, Reflex reflector Side lamps: Outside turn signal lamp 2) Layout Front Side Outside Turn

6 EXTERIOR LAMPS 1) Overview The exterior lamps consist of front lamps, rear lamps and side lamps. Front lamps: Head lamp, Front combination lamp Rear lamps: Rear combination lamp, License plate lamp, High mounted stop lamp, Reflex reflector Side lamps: Outside turn signal lamp 2) Layout Front Side Outside Turn Signal Lamp Outside turn signal lamp Head Lamp High beam Low beam Front Combination Lamp Fog lamp Tail lamp Turn signal lamp

7 Rear Side High Mounted Stop Lamp Rear Combination Lamp Stop lamp Tail lamp Turn signal lamp Backup lamp Rear fog lamp (EU) License Plate Lamp Reflex Reflector

8 1010 3) Operating Process (1) Head lamp aiming (Up/Down) Ordinary operations of head lamp are controlled by the light switch on multifunction switch. The operations by REKES are controlled by STICS. STICS controls the head lamp and tail lamp with LIN data from the auto light sensor when the light switch is in AUTO position. Low beam High beam Tail lamp DRL (Day Time Running Light) DRL is the function to turn on the high beam and tail lamp without any intervention from the light switch. DRL turns off the lamps when turning off the light switch. This is an additional safety device to prevent the accident. Available only for EU market.

831000 1011 (2) Tail Lamp STICS turns on the tail (position) lamp relay when receiving the lamp on signal from the light switch.

9 (2) Tail Lamp STICS turns on the tail (position) lamp relay when receiving the lamp on signal from the light switch. Front Side Position lamp Rear side Tail lamp In vehicle for EU market, the tail (position) lamp comes on when turning the ignition switch to ON position regardless of light switch operation.

10 1012 Control by STICS Tail Lamp Left ON Warning 1. The buzzer sounds with the interval of 0.3 second when opening the driver's door while the tail lamp is turned on and the ignition key is removed. 2. The buzzer output stops when turning off the tail lamp and closing the driver's door. 3. The system outputs "UNLOCK" signal for 5 seconds when the driver's and passenger's door lock switch is locked (while the tail lamp is turned on and the driver's door is open). 4. This function is not available when the ignition key is in the "ON" position. Tail Lamp Auto Cut (Battery Saver) 1. The tail lamp is turned on or off according to the operations of the tail lamp switch. 2. The tail lamp relay is turned off (auto cut) when opening and closing the driver's door after removing the ignition key without turning off the tail lamp. 3. The tail lamp relay is turned on when inserting the ignition key into the ignition switch. 4. The tail lamp relay is not turned off automatically (auto cut) when opening and closing the driver's door while the ignition is removed and the tail lamp is turned on. Not available for EU market.

831000 1013 (3) Auto Light The auto light sensor unit is installed to the back side of the ECM mirror located upper center of the windshield, and detects the

The STICS communicates with the auto light sensor when the ignition is turned on, and turns on or off the tail lamp and headlamp automatically according to

11 (3) Auto Light The auto light sensor unit is installed to the back side of the ECM mirror located upper center of the windshield, and detects the illuminance change. The STICS communicates with the auto light sensor when the ignition is turned on, and turns on or off the tail lamp and headlamp automatically according to the signals from the sensor when the light switch is set to AUTO position. Light Switch Rain Sensor Unit (Integrated auto light sensor) AUTO Auto light sensor STICS controls the head lamp and tail lamp with LIN data with IGN ON and the light switch in AUTO position. Not available for EU market.

12 1014 (4) License Plate Lamp The license plate lamp comes on when the light switch is turned on (Tail, AUTO, Low, High).

13 Circuit Diagram of Head Lamp

14 1016 Circuit Diagram of Tail Lamp

831000 1017 (5) Front Fog Lamp The front fog lamp comes on when the front fog lamp is turned on only with the light switch ON.

15 (5) Front Fog Lamp The front fog lamp comes on when the front fog lamp is turned on only with the light switch ON. The front fog lamp goes out when turning off the ignition or light switch. Front fog lamp Rear Fog Lamp (for EU) Rear fog lamp Rear Fog Lamp Switch The rear fog lamp comes on when the rear fog lamp is turned on only while the front fog lamp is ON.

16 1018 (6) Turn Signal Lamp The left or right turn signal lamp blinks when moving the light switch to appropriate direction. When pressing the hazard switch, both turn signal lamps come on simultaneously. Front Side Outside turn signal lamp Turn signal lamp Rear Side Turn signal lamp Turn Signal Lamp OFF Conditions The turn signal lamp goes out when the steering wheel angle (same direction with turning direction) becomes below 60 from over 70 after turning on a turn signal lamp. The turn signal lamp goes out when the steering wheel angle (opposite direction with turning direction) becomes over 70 from below 70 after turning on a turn signal lamp.

17 Circuit Diagram of Turn Signal Lamp

1020 (7) Stop Lamp The stop lamp switch turns on the stop lamp when depressing the brake pedal. When releasing the brake pedal, the stop lamp goes out.

18 1020 (7) Stop Lamp The stop lamp switch turns on the stop lamp when depressing the brake pedal. When releasing the brake pedal, the stop lamp goes out. High mounted stop lamp Stop lamp Rear fog lamp (for EU) (8) Backup Lamp The backup lamp comes on when moving the gear shift lever to R position with IGN ON. Backup lamp

19 Circuit Diagram of Stop Lamp and Backup Lamp

visor lamps (2), courtesy lamps (4), and scuff

20 INTERIOR LAMPS 1) Overview The interior lamps consist of front room lamps (2), center room lamp, rear room lamp, glove box lamp, sun visor lamps (2), courtesy lamps (4), and scuff lamps (4). 2) Layout Front Room Lamp Center and Rear Room Lamp Sun Visor Lamp Glove Box Lamp

21 Door Courtesy Lamp One lamp in each door

22 1024 3) Operating Process (1) Front Room Lamp A. Door switch: The front room lamps come on when opening a front door with the switch pressed in. B. Driver s spot lamp switch: The front room lamp (driver s) comes on when pressing this switch. C. Passenger s spot lamp switch: The front room lamp (passenger s) comes on when pressing this switch. Door Switch Coupled Front Room Lamp Operation The front room lap comes on when opening a front door with the Door switch ON. 1. The front room lamp comes on when opening a front door. 2. The front room lamp goes out immediately after closing the door with the ignition ON. 3. The front room lamp stays on for 2 seconds after closing the door, and then dims out in 3 seconds. The front room lamp goes out immediately after turning the ignition ON during the dimming period. 4. The front room lamp comes on for 30 seconds when unlocking the doors with REKES key. 5. The front room lamp stays on for additional 30 seconds during lamp operation in Step 5 when receiving 6. the UNLOCK signal from REKES again. The front room lamp stays on when opening a front door, and operates as in Step 3 and The front room lamp dims out when closing the opened door. However, it goes out immediately when 8. getting into the theft deterrent mode. The front room lamp comes on when opening a front door with the ignition ON. And, it goes out 9. immediately when closing the opened door with the ignition ON.

831000 1025 (2) Center and Rear Room Lamp DOOR ( ) ON OFF position: The lamp does not come on. ON position: The lamp stays on. DOOR position ( ): The lamp comes on when the door is opened.

23 (2) Center and Rear Room Lamp DOOR ( ) ON OFF position: The lamp does not come on. ON position: The lamp stays on. DOOR position ( ): The lamp comes on when the door is opened. The lamp goes out when closing the opened door. OFF Center room lamp control by door coupled room lamp operation The center room lamp comes on when opening a rear door with the DOOR switch pressed in. 1. The center room lamp comes on when opening a rear door. 2. The center room lamp goes out when closing the rear doors. Rear room lamp control by tailgate coupled room lamp operation The rear room lamp comes on when opening the tailgatewith the Tailgate lamp switch pressed in. 1. The rear room lamp comes on when opening the tailgate. 2. The rear room lamp goes out when closing the tailgate. (3) Room Lamp Auto Cut 1. When the vehicle enters into theft deterrent mode (STICS sleep mode), the ground circuit of room lamp is turned off. Or the ground circuit of room lamp is turned off 10 minutes after power off. (This is to prevent the battery from discharging when the front room lamp switch or center room lamp switch is in ON position.) The STICS sleep mode is released when unlocking the doors or turning on the ignition. 2. The ground circuit of room lamp is turned on when turning on the ignition while the room lamp auto cut is off.

1026 (4) Glove Box Lamp The glove box lamp

door courtesy lamp comes on when opening the

24 1026 (4) Glove Box Lamp The glove box lamp comes on when opening the glove box with the tail lamp on. (5) Door Courtesy Lamp and Scuff Lamp The door courtesy lamp comes on when opening the door. (6) Sun Visor The sun visor lamp comes on when opening the vanity mirror.

25 (7) Circuit Diagram of Room Lamp

1. LAMP SPECIFICATIONS

8310-00 07-3 1. LAMP SPECIFICATIONS 1) Exterior Lamps Description Numbers Specification Headlamp High beam 2 H1-55W Low beam 2 H7-55W Turn signal lamp 2 P21W Position lamp - LED Front fog light 2 H16-19W