Headlight Module Conversion Kit

Transcription

1 II #0317 pplication: orvette Headlight Module onversion Kit Part Includes 1 - onversion Kit Tools Needed PREUTIONS Do not energize the ontroller until all wiring changes are complete and proper. While adjusting the headlamp, do not apply a power assist means such as drills, air drivers, etc. to the knob of the actuator. Operation of the headlamp MUST be either through the normal operation of the switch and controller or by hand rotation of the knob. PRIOR TO SSEMLY: insure that the retractable headlamp system on the vehicle is RELY DRIVEN. There are two quick methods of identification. STEP 1. Locate the relay cover and relays on the forward side of the front left wheel well. Remove cover and inspect for 3 relays offset in a diagonal line. STEP 2. Look at the actuator on the Retractable headlamp assembly. It should be a self contained plastic housed motor with 2 stage gear reproduction. Look on the case for the part number. The left hand actuator will feature part number and the right hand Note, also, that the actuator has 3 wires exiting the actuator. INSURE THT LL PRTS RE INLUDED IN THE SERVIE PKGE INLUDING: This kit is designed to provide the electrical wiring interface between the OE Headlight ontrol System and style headlight motor units. 1 Headlamp ctuator ontrol Module (part number ) 1 Wiring dapter package containing: 2 ctuator wire pigtails (3-wire to 2-wire) (part number ) 1 ontrol Module to Relay wire adpater harness (5-wire) (part number ) 1 ontrol Module to ctuator Wire dapter Harness (4-wire) (part number ) NOTE: style motors are not included. DISSSEMLY STEP 1. Open Hood. Turn ignition switch OFF and disconnect negative (-) battery terminal and insure that cables cannot come into inadvertant contact with battery terminals or external power sources. STEP 2. Remove the retractable headlamp assembly car colored close-out bezel taking care not to mar or scratch surfaces. STEP 3. Remove the car colored headlamp cover. MMotorworks Midamotorworks MidmericaMotorworks 2900 N. Third Street, P.O. ox 1368, Effingham, IL Worldwide: FX: mail@mamotorworks.com Mid merica Motorworks, Inc. ll rights reserved.

2 Page 2 STEP 2. STEP 3. EZEL OVER U RKET STEP 4. Remove retractable headlamp assembly. Please note the hood hinge bracket. STEP 5. Remove and discard relays, relay cover and mounting bracket. Note that there are five (5) harness connectors to the three (3) relays. STEP 4. STEP 5. HOOD HINGE RKET

3 Page 3 STEP 6. Look at the ontroller (P/N ). To mount the controller, two holes must be drilled into the wheel well in the general location of the relay cover and mounting bracket. The holes must be spaced as shown and 8mm diameter. WRNING: DO NOT USE MODULE ITSELF TO DRILL HOLES. USE THE TEMPLTE PROVIDED ELOW. DRILL THIS HOLE TEMPLTE 101.0mm (3.976 INHES) DRILL THIS HOLE 100.0mm (3.937 INHES)

4 Page 4 STEP 7. Mount the controller (part number ) over the wheel well in the same general location as the previous relay pack. NOTE: the old pack mounting bracket locations differ from those of the controller (part number ). The controller has two threaded inserts (M6x1 thread). Locate the controller to the desired position on the wheel well and drill two new holes consistent with the controller mounting inserts. Use two M6x1 screws to mount the controller to the wheel well. Tighten screws to 4.5 N.m (39.82 in-lb) torque maximum.

5 Page 5 STEP 8. Relay onnections: The relays having been removed, take time to note the connections and wire colors to the relays. It is very important that these connections be made accurately. lthough the wire colors shown are typical. It is not uncommon for colors to vary for a variety of reasons. efore removing the connectors, mark and wrap masking tape around each of the five (5) wire bundles. Remove the connectors in preparation to slice connect new connectors. RED YELLOW LK RED YELLOW LK Left Hand Door Relay onnector 2-Gray Right Hand Door Relay onnector 2 Gray YELLOW GRY LK D RED Isolation Relay onnector lack WHITE DRK GREEN NO ONNETION Left Hand Door Relay onnector lack WHITE/LK DRK GREEN/WHITE NO ONNETION Right Hand Door Relay onnector 1 lack NOTE TUL OLOR OF WIRES FOUND

6 Page 6 STEP 9. ut off and discard relay connectors. MSKING TPE ONDUIT MSKING TPE REMOVE STEP 10. Peel back the protective conduit in order to expose the wires. The connector assembly part number (5-wire) has wires of varying length and the connections are staggered such that connections should be made down the wires. Wire lengths should be cut as necessary. ONDUIT

7 Page 7 STEP 10. ttach connector adapter assemblies and to wires using the splice connectors on the adapter assemblies. Note that not all wires are to be reconnected. Leave unused wire in place. STEP 11. The new system that you have installed is electrically the same as those used in orvette models built for 1988, 1989 and Please refer to the standard service manuals for those models when trouble shooting the system. STEP 12. Install new headlamp assemblies onto hood. Transfer headlamp capsules form the old units to the new and re-fit the cover and bezel. lign. over. STEP 13. onnect the actuator adapter assemblies (3 way to 2 way pigtails part number ) to the right hand and left hand connectors that the head lamp actuator would normally connect (part number ) STEP 14. fter insuring that all connections are proper, secure and mounted away from the rotating space of the headlamp, connect the negative battery power.