INSTALLATION INSTRUCTIONS FOR PART

Transcription

1 INSTLLTION INSTRUCTIONS FOR PRT PPLICTIONS FORD Edge 007 / Expedition 007 F / FreeStar Mustang / Five-Hundred Freestyle / Focus / Super Duty 008 F Series / Fusion / Explorer Explorer Sport Trac Taurus 008, Taurus X 008 MERCURY Monterey / Milan Montego / Mountaineer Sable 008 LINCOLN Lincoln Mark LT Factory Nav Only: MKX 007 / MKZ 007 / Navigator 007 Zephyr KIT FETURES Double DIN Radio Provision Stacked ISO DIN Head Unit Provision KIT COMPONENTS ) Radio Housing (Double DIN and Stacked ISO DIN) ) Double DIN rackets C) Spacers D) (4) Screws C D TOOLS REQUIRED: Cutting Tool Panel Removal Tool Phillips Screwdriver Socket Set COPYRIGHT METR ELECTRONICS CORPORTION

2 95-58 TLE OF CONTENTS Dash Disassembly Ford Edge Ford F / Expedition Lincoln Mark LT Ford Mustang Ford Five Hundred Mercury Sable Ford Taurus Mercury Montego Ford Fusion Mercury Milan Ford Freestyle Ford Taurus X Ford Freestar Mercury Monterey Ford Focus Ford Explorer Ford Explorer Sport Trac Mercury Mountaineer Ford F Series Super Duty Ford Super Duty Lincoln Navigator Lincoln MKX Lincoln MKZ ,4 Lincoln Zephyr ,4 Kit ssembly Double DIN Head Unit Provision...5 Stacked ISO DIN Head Unit Provision...6 Final ssembly...7 *Note: Refer also to the instructions included with the aftermarket radio.

3 95-58 DSH DISSSEMLY FORD F LINC0LN MRK LT FORD EXPEDITION 007 FORD EDGE 007 Unsnap and remove entire panel surrounding the radio and climate controls. (Figure ) Remove (4) 9/" screws to remove the factory radio. (Figure )

4 95-58 DSH DISSSEMLY FORD MUSTNG *Note: Refer also to the instructions included with the aftermarket radio Remove the small rectangular shifter lever trim panel if equipped. (Figure ) Remove () Phillips screws from under the center armrest at the back of the shifter trim panel (including cup holders). (Figure ) Unclip and remove panel. (Figure ) Unclip and remove the () center stack trim panels from the left and right side of the radio and climate controls. (Figure C) Remove (6) 9/ screws from center trim panel surrounding the radio and climate controls then unclip and remove panel. (Figure D) Remove (4) 9/ screws from the radio to remove. (Figure E) Continue to final assembly. C E D

5 95-58 DSH DISSSEMLY FORD FIVE-HUNDRED /FORD TURUS 008 MERCURY MONTEGO , MERCURY SLE 008 *Note: Refer also to the instructions included with the aftermarket radio. Unclip and remove the small rectangular trim around shift lever. (Figure ) Unclip and remove the entire panel (including cup holders) surrounding the shift lever. (Figure ) Remove () 9/ screws at the bottom of the center radio/climate control panel. (Figure C) Unclip and remove the center panel. (Figure D) Remove (4) 9/ screws from the radio to remove. (Figure E) Continue to final assembly. C E D

6 95-58 DSH DISSSEMLY FORD FUSION MERCURY MILN Unsnap and remove entire panel surrounding the radio and climate controls. (Figure ) Remove (4) 9/" screws to remove the factory radio. (Figure ) 4

7 95-58 DSH DISSSEMLY FORD FREESTYLE FORD TURUS X 008 Unclip and remove entire panel surrounding the radio and a/c controls. (Figure ) Remove (4) 9/ screws from radio to remove. (Figure ) 5

8 95-58 DSH DISSSEMLY FORD FREESTR MERCURY MONTEREY Unsnap and remove entire panel surrounding the radio and climate controls. (Figure ) Remove (4) 9/" screws to remove the factory radio. (Figure ) 6

9 95-58 DSH DISSSEMLY FORD FOCUS Unsnap and remove entire panel surrounding the radio and climate controls. (Figure ) Remove (4) 9/" screws to remove the factory radio. (Figure ) 7

10 95-58 DSH DISSSEMLY FORD EXPLORER/EXPLORER SPORT TRC MERCURY MOUNTINEER Open center console and remove () Phillips screws then unclip and remove entire panel surrounding shifter. (Figure ) 4 Remove dash panel surrounding radio to access the factory radio screws. (Figure ) Remove (4) 9/" screws to remove the factory radio. (Figure ) C 8

11 95-58 DSH DISSSEMLY FORD F SERIES SUPER DUTY Unsnap and remove entire panel surrounding the radio and climate controls. (Figure ) Remove (4) 9/" screws to remove the factory radio. (Figure ) 9

12 95-58 DSH DISSSEMLY FORD SUPER DUTY 008 Unclip and remove the power outlet panel and the blank panel on the left and right side of the radio trim panel. (Figure ) Remove the () 9/ screws exposed behind the two panels remove in step. 4 Unclip and remove the entire radio trim panel including the a/c control and vents. 5 Remove (4) 9/ screws securing the radio. Continue to kit assembly 0

13 95-58 DSH DISSSEMLY LINCOLN NVIGTOR 007 Unclip and remove the panel surrounding the shifter. (Figure ) Remove () 9/ screws from the bottom of the radio/climate control trim panel. (Figure ) 4 Unclip and remove the entire panel surrounding the radio and including the climate controls. (Figure ) 5 Remove (4) 9/ screws securing the radio. Unplug and remove the Radio.

14 95-58 DSH DISSSEMLY LINCOLN MKX 007 Open center console lid and unclip and remove the center console trim panel surrounding the shifter. (Figure ) Remove () Phillips screws from the storage bin then unclip and remove the bin. (Figure ) 4 Unclip and remove the upper and lower center trim panel as one assembly. (Figure C) 5 Remove (4) 9/ screws securing the radio. Unplug and remove the Radio. C

15 95-58 DSH DISSSEMLY LINCOLN MKZ 007/LINCOLN ZEPHYR 006 Unclip and remove the top of the center console. (Figure ) Open ashtray door and remove ashtray then remove () Phillips screw from inside ashtray cavity. Close ashtray door. 4 Unclip and remove the climate control and trim panel assembly starting at the bottom edge. (Figure ) 5 Open the climate control vents and pull straight outward to remove. (Figure C) Continue on page 4. C

16 95-58 DSH DISSSEMLY LINCOLN MKZ 007/LINCOLN ZEPHYR Remove () 9/ from the bottom of the radio trim panel assembly and () 9/ screws from inside the vents. (Figure D) D 7 Unclip the radio trim panel/radio assemmbly. Unplug and remove assembly. (Figure D) 8 Remove (4) 9/ screws securing the radio to the trim panel and remove the radio. (Figure E) E 4

17 95-58 KIT SSEMLY DOULE DIN RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. For the 007 Ford Edge/Expedition, Explorer/Fusion/Mercury Milan, F-50, Five Hundred/Freestyle/Mustang/ Mercury Montego, Lincoln Mark LT and the 008 Super Duty, cut and remove the rear mounting tabs from the Double DIN rackets a. If your vehicle is not listed above move to step. For the 007 Ford Edge/Expedition, Explorer, Fusion, 007 Mustang and the 008 Super Duty attach the included spacers to the back of the radio housing mounting tabs. a. If your vehicle is not listed above move to step. (Figure ) ttach the double DIN brackets to the radio housing. Note: The notch in the housing should be on top. (Figure,) C 4 Slide the Double DIN radio into the radio housing/bracket assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) 5

18 95-58 KIT SSEMLY STCKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. For the 007 Ford Edge/Expedition, Explorer/Fusion/ Mercury Milan, F-50, Five Hundred/ Freestyle/Mustang/Mercury Montego, Lincoln Mark LT and the 008 Ford Super Duty, cut and remove the rear mounting tabs from the Double DIN rackets. a. If your vehicle is not listed above move to step. For the 007 Ford Edge/Expedition, Ford Explorer, Ford Fusion, 007 Mustang and the 008 Super Duty attach the included spacers to the back of the radio housing mounting tabs. (Figure ) a. If your vehicle is not listed above move to step. 4 ttach the double DIN brackets to the radio housing. Note: The notch in the housing should be on top. (Figure,) Slide the ISO mount units into the radio housing/bracket assembly and secure the units to the assembly using the screws supplied with the units. (Figure C) C 6

19 95-58 FINL SSEMLY FINL SSEMLY C () Strip wire ends back /" ) Twist ends together C) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short ) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short METR / EI WIRING CODE V Ignition / cc Red V att / Memory Yellow Ground lack* Power ntenna lue mp Turn-On lue / White mp Ground lack / White Illumination Orange Dimmer Orange / White Right Front (+) Gray Right Front (-) Gray/ lack Left Front (+) White Left Front (-) White / lack Right Rear (+) Violet Right Rear (-) Violet / lack Left Rear (+) Green Left Rear (-) Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 7

20 95-58 INSTRUCTIONS REV. 08/0/07 COPYRIGHT METR ELECTRONICS CORPORTION INST95-58