R-29 Sedan & Command Bridge. Owner s Manual. Quality Craftsmanship Since 1958

Transcription

1 R-29 Sedan & Command Bridge Owner s Manual Quality Craftsmanship Since 1958

2 TABLE OF CONTENTS Table Of Contents... 2 Congratulations... 3 Safety... 3 Symbol Glossary... 4 Specifications (Subject To Change Without Notice)... 5 Equipment Location... 6 Starboard Fittings... 6 Port Fittings... 7 Main Cabin Top Deck Components... 8 Stern Components... 9 Main Cabin And Cockpit Lights Fuel System, Engine, Generator & Webasto Furnace Closed Engine Cooling System Raw Water / Sea Strainer System Fresh Water Plumbing System Shower Sump Bilge Pump System Waste System With Macerator Pump Electric Pumps Onboard Air Conditioning Webasto Furnace Solar Panel Battery Configuration Fuse Location & Values Fuse Location & Values Power Panel And Solar Panel Control Box Ac Distribution Panel & Rotary Switch V Helm Control Operation Ranger Tug R-29 Wiring Schematic (Acc. 1) Ranger Tug R-29 Wiring Schematic (Acc. 2) Ranger Tug R-29 Wiring Schematic (Acc. 3) Ranger Tug R-29 Wiring Schematic (Lighting) Ranger Tug R-29 Wiring Schematic (P.D.P.) Ranger Tug R-29 Working Deck Mast Set Up And Takedown Care And Maintenance Example Of A Preparation For The Road Checklist Example Of A Spring Pre-Launch Checklist Example Of Winter Storage Checklist Notes

3 CONGRATULATIONS The Ranger Tug family has a passion for boating. We are committed to continuous process improvement in all areas that affect our customer s satisfaction with our products and providing great customer service. SAFETY Safety is always a concern at Ranger Tugs. Please read all manuals to ensure that equipment is used in a safe manner. We highly recommend attendance in a Coast Guard approved boating safety course. Such courses are available from the Coast Guard directly or from boating organizations. Owners should have annual inspections to ensure that all safety equipment is current. Operating, servicing and maintaining a recreational marine vessel can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, service your vessel in a well-ventilated area and wear gloves or wash your hands frequently when servicing this vessel. For more information go to 3

4 SYMBOL GLOSSARY Attention! Important Operating or Maintenance Instructions Attention! Electrical Shock Hazard Fresh Water Black Water Fuel Standard Equipment OPT Optional Equipment Hints 4

5 SPECIFICATIONS R-29 S Length... 28' 10" Length Overall (w/swim step)... 33' 4" Beam... 10' 0" Draft... 28" Weight, Dry... 10,500 lbs Water Bridge Clearance (mast up)... 13' 11" Water Bridge Clearance (mast down)... 9' 11" Height on Trailer (mast down)... 13' 3" Fuel Capacity gal Water Capacity (fresh) gal Holding Tank Capacity gal Hot Water Tank Capacity... 8 gal Length Overall on Trailer with no dinghy (RIB)... 39' 6" 8.79 m m 3.05 m.71 m 4,762 kg 4.24 m 3.02 m 4.04 m L L L L L R-29 CB Length... 28' 10" Length Overall (w/swim step)... 33' 4" Beam... 10' 0" Draft... 28" Weight, Dry... 10,800 lbs Water Bridge Clearance (mast up)... 13' 11" Water Bridge Clearance (mast down)... 9' 11" Height on Trailer... 13' 3" Fuel Capacity gal Water Capacity (fresh) gal Holding Tank Capacity gal Hot Water Tank Capacity... 8 gal Length Overall on Trailer with no dinghy (RIB) m m 3.05 m.71 m 4,899 kg 4.24 m 3.02 m 4.04 m L L L L L (Subject to Change Without Notice) 5

6 EQUIPMENT LOCATION STARBOARD FITTINGS D E Keep all vents, drains and exhausts clear of any obstructions to ensure proper performance of each system. 16 ➐ ➌ ➎ ➓ ➑ ➋ ➍ ➒ 14 A ➏ D A E B B C C (Luxury Edition) (NW Edition) 13 ➊ ➊ Bow Ladder ➋ Shore Power Inlet(s) ➌ Diesel Fill On Deck ➍ Fuel Tank Vent ➎ Waste Outlet On Deck ➏ Holding Tank Vent ➐ Foredeck Anchor Windlass Switches ➑ Aft Bilge ➒ Forward Bilge ➓ Boarding Ladder Rudder Keel Drain Plug Bow Thruster Keel A B C D E Prop Water Fill On Deck Stern Thruster Macerator Shower Sump Sink Drain AC Aft AC Forward

7 PORT FITTINGS Keep all vents, drains and exhausts clear of any obstructions to ensure proper performance of each system. ➊ ➋ 11 ➌ ➎ ➍ ➑ ➏➐ 12 ➓ ➒ ➊ Water Tank Vent ➋ Anchor Locker Drain ➌ Galley Sink Drain ➍ Bow Thruster ➎ Generator Vent Cover ➏ Generator Exhaust ➐ Engine Exhaust ➑ Keel ➒ Prop ➓ Rudder Webasto Diesel Heater Exhaust Stern Thruster 7

8 MAIN CABIN TOP DECK COMPONENTS ➊ ➋ ➌ ➎ ➍ ➏ ➐ ➊ Anchor Light ➋ Running Light ➌ TV Antenna ➍ Radar ➎ Searchlight ➏ Horn ➐ Navigation Light (RED Port, GREEN Starboard) 8

9 RN COMPONENTS ➊ ➋ ➌ 18 ➌ ➍ ➍ ➍ ➍ ➐ ➐ ➏ ➏ ➐ ➐ ➎ ➎ ➒ ➑ ➓ ➑ ➒ ➊ Flagstaff Mount ➋ Deck Shower ➌ Amber Courtesy Lights ➍ Swim Platform Struts ➎ Cockpit Drain with Flap ➏ Towing Strapdown Eye ➐ Trim Tab Ram ➑ Trim Tab ➒ Under Water Lights ➓ Stern Thruster Prop Rudder Prop Zinc Transom Zinc Swim Platform Swim Platform Fenders Rail Chain or Chain Gate Propane Locker Dinghy Cleats Trim Tab Zincs Thruster Zinc Patio Railing Stand Off Mounts Dinghy Davit 9

10 MAIN CABIN AND COCKPIT LIGHTS ➊ V-Berth Cabin Lights ➋ Head Lights ➌ Under Bed Lighting ➍ Indirect Cabin Lights ➎ Cockpit & Transom Lights ➏ Red White Combo ➐ Overhead White Lights ➑ Exterior Red/White ➒ Reading Lights ➓ Underwater Lights Main Cabin Switch Dash Switch Forward Cabin Switch Head Switch Cockpit Switch Panel Switch On Fixture ➓ ➎ ➑ ➎ ➑ ➍ ➐ ➍ ➏ ➍ ➌ ➒ ➏ ➏ ➊ ➊ ➊ ➓ ➎ ➑ ➑ ➎ ➍ ➐ ➏ ➋ ➋ ➍ ➋ ➋ ➌ ➒ 10

11 FUEL SYM, ENGINE, GENERATOR & WEBASTO FURNACE Volvo D4 300hp There is a secondary on-engine fuel filter that is not shown on this drawing. You will be able to find information about this filter in the diesel engine manual supplied with your boat. The secondary filter is where the water-in-fuel sensor is located. Main engine fuel shutoff is located underneath the forward engine hatch as you enter the main cabin. The primary fuel filter is mounted on the bulkhead in the engine compartment. There is a drain in the bottom of this filter for draining water. Fuel Tank Engine supply Sender Fuel filter Generator supply Engine return Fuel fill Webasto Engine shut-off valve Vent Generator return Generator shut-off valve Fuel filter Engine Generator filters Generator RN 11

12 CLOSED ENGINE COOLING SYM Provides an alternate heating system for the Fresh Water Heater and provides primary heating source for the Forced Air Cabin Heater. This system is also designed to provide cooling to the internal components of your engine. Please refer to your engine operations manual for more information. Use only Volvo VCS coolant in this system. Do not mix coolant types. Close black handled coolant valves on front of engine if a leak is suspected in either the fresh water heater or forced air cabin heater. This will keep coolant inside of the engine where it is needed most. Cabin Heater Hot Water Heater Heater Switch at helm Valves Engine 12

13 RAW WATER / SEA STRAINER SYM Engine raw water thru-hull and strainer Multi port sea strainer for head and raw water wash down pump. Generator raw water thru-hull strainer A/C Raw Water Input Generator Thru-hull/Valve Generator Strainer Engine Strainer Engine Thru-hull/Valve Engine Multi Strainer Multi Strainer Thru-hull/Valve Raw Water Washdown A/C Raw Water (OPT) Head Raw Water Generator 13

14 FRESH WATER PLUMBING SYM 60 Gallon Fresh Water Tank, 8 Gallon Hot Water Heater, 3.5 GPM Fresh Water Pump. Shower hot Shower cold Head sink cold Head sink hot Hot water heater Galley sink hot Galley sink cold Water Tank Water tank sending unit Fresh water pump/strainer (under removable teak panel) Water pump switch/gauge located in midberth Transom shower hot/cold 14

15 SHOWER SUMP 12V, 800 GPH (This should be inspected for debris on a regular basis if shower is used frequently.) The shower sump box is located underneath a removable panel in the stateroom floor positioned just outside the head door. Forward AC condensate drain Sump pump Shower drain Aft AC condensate drain Thru-hull exhaust 15

16 BILGE PUMP SYM 12V 1100GPH The bilge pumps operate automatically with electronic float switches even with battery switches and breakers in the OFF position. However, the BILGE PUMP and BILGE PUMP2 will run continuously once their switches are placed in the on position. Monitor the outflow accordingly. Do not run when dry. Manual switches/high water alarm switch are located at the helm. High water alarm sensor Forward bilge pump Check valve 1100 GPH through hull Aft bilge pump Check valve 1100 GPH through hull 16

17 WA SYM WITH MACERATOR PUMP 40 Gallon Tank with standard pump out, and vent Macerator pump out Waste tank level can be checked by utilizing the head control panel. Please refer to your head operations manual. Waste tank pump out stations are widely available. Please follow the directions carefully for the pump out equipment you are using to avoid damage to the waste system. Boat owner is responsible for following all applicable laws when using the macerator system to pump out into the surrounding waters. Overboard shutoff valve is accessed under berth inline with the macerator pump. Overboard Shutoff Valve Macerator Waste Tank Valve must remain either locked, or only able to be opened by using a tool when not using macerator. Example: zip tie Marine Head Pump Out (on deck) Macerator Discharge Vent Raw water into head Multi Strainer Multi Strainer Thru-hull/valve 17

18 ELECTRIC PUMPS ONBOARD Macerator (Under Berth) Shower Sump (Under floor panel just outside of head door) Fresh Water Pump (Under floor panel just inside cabin) Forward Bilge Pump Toilet Water Pump (Starboard lazerette forward) Engine A/C Pump (optional) (Engine room bulkhead forward) Aft Bilge Pump Washdown Raw Water Pump (Engine room bulkhead aft) 18

19 AIR CONDITIONING A/C Vent Forward A/C Unit (Under Berth) Front A/C Control Panel Forward A/C Air Intake Grill (keep uncovered) A/C Vent A/C Vent Main Cabin A/C Unit (Under Helm Seat) Main Cabin A/C Air Intake Grill (keep uncovered) Main Cabin A/C Control Panel (in Mid-Berth) A/C Raw Water Pump Multi Strainer Thru Hull/Valve 19

20 WEBASTO FURNACE Webasto furnace is located under access panel below refrigerator. The control panel is located at the quarter berth power management center. The fuel pump is in the salon floor hatch compartment inside of the black box. Interior Heat Vent Interior Heat Vent Webasto Furnace Exhaust (keep unblocked/ gets very warm) Exterior Heat Vent Fuel Pump / Filter (inside black box) 20

21 SOLAR PANEL Solar panel 160 watt, with display panel The solar panel is designed to provide charging to the house & engine batteries. 90% of its charge is dedicated to the house battery and 10% is dedicated to the engine battery. The green light on the solar display indicates proper operation. The solar display is located in the mid-berth. The controller is located in the port lazarette *Keep panel clean and completely uncovered for best results Battery Banks 1 = House 2 = Engine 3 = Thruster Solar Panel Display Batteries Thruster Battery 1 1 Controller 21

22 OFF ON BATTERY CONFIGURATION 4 House Batteries, 1 Engine Battery, 1 Thruster Battery. House, engine, & battery parallel switches are located behind the port side circular access panel in the cockpit. Thruster battery switches located in the midberth Once the EMERGENCY PARALLEL switch is placed in the on position the power from the HOUSE batteries will be transferred to the ENGINE battery. Use only for EMERGENCY starting of the engine. If the house bank drops below 10.8v you must reset the charging relay by switching on the parallel while the engine is running. Batteries Engine 3 3 Switches in cockpit behind circular access panel HOUSE Battery Banks HOUSE 1 = House 2 = Engine 3 = Thruster BATTERY PARALLEL Generator ENGINE RN 22

23 FUSE LOCATION & VALUES These DC fuse blocks and windlass breaker are located behind a hinged access panel on the starboard side in the head behind the mirror. Fuses are automotive blade type and all values shown below are in Amps. Navigation Dash 1 Dash 2 Transducer Network Radar Radar Switch Panel (4 switch) Switch Panel (8 switch) Switch Panel (8 switch) Head Tv #1 Tv #2 Antenna Light Switch (Vberth) VHF Heater Stereo Stereo Amp Head Lights Wine Cooler 12V Outlet (Vberth) Shower Pump Webasto Remote 12V Outlet (dinette) Trim Tabs 12V Outlet (dash) Webasto Heater Spotlight Remote * To reset, reinsert yellow arm up into the breaker. To test, press red button and the yellow arm should flip down. 23

24 FUSE LOCATION & VALUES These DC fuse blocks are located behind the wood hatch in the midberth. Fuses are automotive blade type and all values shown below are in Amps. Hot powered (always on) Bilge Pump #1 CO Monitor #1 Bilge Pump #2 CO Monitor #2 Bilge Alarm Volt Meter Battery #3 Downrigger (starboard) Autopilot Pump Downrigger (port) Washdown 12V Outlet (mid-berth) Refrigerator Freshwater Pump Cabin Lights Hot powered (always on) Refrigerator (aft) Switch Panel (4 switch) Misc. Lights Spotlight LPG Controller Engine Hatch (switch) Volt Meter Battery #2 This DC fuse block is mounted under the bridge dash. Fuses are automotive blade type and all values shown below are in Amps. Nav. Display (bridge) Switch Panel (bridge) 12V Outlet (bridge) 24

25 POWER PANEL AND SOLAR PANEL CONTROLLER BOX Located in the port side cockpit lazerette Solar Panel Controller may be mounted forward of the power panel on boats with a generator 50 Amp Breaker Command Bridge Sedan 50 Amp Breaker 150 Amp Breaker Solar Panel Controller Automatic Charging Relay (ACR) Automatic Charging Relay (ACR) 300 Amp ANL Bus Fuse There are two more 250 amp ANL fuses for the Bow and Stern thruster located in the midship outboard of the thruster battery switches behind cabinet door. 300 Amp ANL Bus Fuse 25

26 AC DISTRIBUTION PANEL & ROTARY SWITCH AC Distribution Panel AC Rotary Selector Switch (Available with Generator) AC Main Line 2 (with AC) A/C Main 1 must on in order for batteries to charge. The AC Rotary Switch Selector Switch will determine which source of incoming 120 Volt power to use for your AC Distribution Panel. AC Distribution Panel Water Pump gauge/switch BOW THRUR MICRO- WAVE ACCESS- ORY COOK TOP OVEN GALLEY OUTLETS ACCESS- ORY ICE MAKER OUTLETS FORWARD ACCESS- ORY WATER HEATER ON SALON OUTLETS ACCESS- ORY ACCESS- ORY RN THRUR AC Main 1 AC Distribution Panel with Generator BOW THRUR MICRO- WAVE ACCESS- ORY FWD AIR GALLEY OUTLETS OUTLETS FORWARD COOK TOP OVEN ICE MAKER AFT AIR AFT RELAY AC MAIN 1 AC Main 1 SALON OUTLETS WATER HEATER ACCESS- ORY RN THRUR AC MAIN 2 AC Main 2 Water Pump gauge/switch ON AC Main 1 AC Main 1 AC Main 2 Battery Banks 1 = House 2 = Engine 3 = Thruster 26 AC Main 2 used for only FWD/AFT air and aft relay breakers

27 12V HELM CONTROL OPERATION Armed = Red light/audible alarm Off = Red light only. The high bilge alarm should be set to the armed position for it to automatically operate. This is wired directly to the hot fuseblock. The high bilge alarm will still be active regardless of battery switch position. The bilge pumps operate automatically with electronic float switches regardless of battery switch position. However, the BILGE PUMP and BILGE PUMP2 will run continuously once their switches are placed in the on position. Monitor the outflow accordingly. Do not run when dry. The Heater Control will operate the fan speed of the Heater Craft Heater. The Heater Craft Cabin Heater will only warm as the engine reaches normal operating temperature. At Helm Heater Control High Water Alarm WIPER WIPER WIPER FWD BILGE PUMP AFT BILGE PUMP ANCHOR/ NAV CHART LIGHTS HORN TEST Resettable switch breakers OFF ARMED BILGE ALERT HIGH WATER ALARM At Helm In Cockpit Resettable switch breakers O/H FANS THRUR REMOTE MACER- ATOR WIND- LASS COCKPIT LIGHTS UW LIGHTS ACCY ACC is for overhead cockpit lights 27

28 RANGER TUG R-29 WIRING SCHEMATIC (ACC. 1) +12V Dash Fuse Block #1 Subpanel 8 Switch Subpanel 8 Switch TV #1 TV #2 TV Antenna 12V Outlet (Dinette) Subpanel 4 Switch (Dash) LT Switch (V-berth) Head (Toilet) Heater (Diesel) 30A R-29 Accessories #1 ELECTRICAL SCHEMATIC Switched w/ House Battery Switch To Subpanel 4 Switch (Bridge) 10A Horn RED 10 ORG/WHT Nav LT RED 10 To Lighting Schematic RED 10 Chart LT To Lighting Schematic 5A Bilge Pump RED 10 RED/BRN 16 To Acc. #2 Schematic (#1) 5A Bilge Pump RED 10 PUR/BRN 16 (#2) 30A Wiper Park BLU/BLU 16 To Acc. #2 Schematic 5A RED 16 Wiper RED 10 Speed RED 16 (Port) Controller M Wiper Park BLU/BLU 16 5A RED 16 Wiper RED 10 Speed RED 16 (Mid.) Controller M Wiper Park BLU/BLU 16 5A RED 16 Wiper RED 10 Speed RED 16 (Stbd) Controller M 7.5A PUR/GRY 16 TV - see MFR Schematic 7.5A GRY/PUR 16 TV - see MFR Schematic 1A PUR/GRY 16 TV Antenna - see MFR Schematic 20A ORG/WHT 10 YEL 10 12V 20A Macerator RED 10 BRN 10 YEL 10 M Pump 30A Defrost Fans RED 10 3A PUR/WHT 16 Thruster 5A RED 10 RED 16 Wireless Thruster Wireless Remote - Remote see MFR Schematic Head BRN 10 Pump M To Lighting Schematic Head Pump 25A RED/BLK 10 Head (Toilet) - see MFR Schematic 20A ORG/PNK 10 Macerator Diesel Heater - see MFR Schematic M M YEL 10 YEL 10 YEL 10 Heater 1A RED/ Signal +12V Bridge Fuse Block Switched w/ House Battery Switch 12V Outlet 20A ORG/WHT 10 YEL 10 12V (Bridge) 10A RED 10 Deck LT To Lighting Schematic Subpanel 20A 4 Switch 10A (Bridge) Horn RED 10 To Subpanel 8 Switch -12V GND Nav/Anchor LT RED 10 10A To Lighting Schematic To Lighting Schematic

29 RANGER TUG R-29 WIRING SCHEMATIC (ACC. 2) +12V Dash Fuse Block #2 R-29 Accessories #2 Switched w/ House Battery Switch ELECTRICAL SCHEMATIC -12V GND Trim Tabs Wine Cooler Heater Head LT Search LT (Remote) VHF Stereo Stereo Amp 20A ORG 10 YEL 10 Trim Tab - see MFR Schematic 10A 15A ORG 10 ORG/GRY 10 YEL 10 Heater - see MFR Schematic To Lighting Schematic To Lighting Schematic 7.5A 3A RED 16 RED/WHT 16 Wine Cooler - see MFR Schematic RED 16 ORG 16 OFF VHF Radio - see MFR Schematic Stereo Deck - see MFR Schematic YEL 10 Stereo WHT/ 15A Memory To House Battery 10A RED/GRY 16 Stereo Amp - see MFR Schematic UNSWITCHED ALWAYS ON! 12V Outlet (Dash) 12V Outlet (V-berth) Shower Pump 20A ORG/WHT 10 12V YEL 10 20A YEL 10 ORG/WHT 10 12V 10A +12V Thruster Battery Fuse Block Bilge Pump (#1) Voltmeter Bilge Pump (#2) CO Monitor (#1) CO Monitor (#2) Bilge Alarm 5A 3A 5A 3A 3A 3A LF (in) BRN/ORG 10 To Acc. #1 Schematic BRN/RED 16 RF (in) LR (out) RR (out) Bilge Pump RED/GRN 16 To Acc. #3 Schematic To Acc. #1 Schematic BRN/BLU 16 RED/BLK 16 RED/BLK 16 WHT/BLK 16 M MLF (in) Bilge Pump M MRF (in) CO Monitor - see MFR Schematic CO Monitor - see MFR Schematic Bilge Alarm - see MFR Schematic BRN/WHT 16 WHT/BRN 16 MLR (out) A B C MRR (out) Shower Pump M BL (out) BR (out) YEL 10 29

30 RANGER TUG R-29 WIRING SCHEMATIC (ACC. 3) +12V PDP Fuse Block R-29 Accessories #3 Switched w/ House Battery Switch ELECTRICAL SCHEMATIC Washdown -12V GND Washdown 12V Outlet (Quarter Berth) Refrigerator Refrigerator (Aft) Downrigger (Stbd) Downrigger (Port) Autopilot Pump 20A 20A 20A 20A 40A 40A 40A RED 10 RED/PUR 10 BRN 10 YEL 10 M 12V YEL 10 ORG/PUR 10 YEL 10 Refrigerator - see MFR Schematic ORG 10 YEL 10 Refrigerator - see MFR Schematic RED/WHT 10 RED/WHT 10 BRN/BLK 10 Downrigger - see MFR Schematic Downrigger - see MFR Schematic Autopilot - see MFR Schematic YEL 10 YEL 10 YEL 10 Cabin LT Spotlight To Lighting Schematic To Lighting Schematic Water Gauge ORG 16 A B C Misc LT To Lighting Schematic UNSWITCHED ALWAYS ON! Fresh Water Pressure Subpanel 4 Switch (Deck) 10A BRN/YEL 10 To Lighting Schematic To Acc. #2 Schematic +12V Engine Battery Fuse Block 3A RED/BLU 16 Voltmeter Engine Hatch (Switch) Stove (Switch) 20A 1A RED 10 ORG/BLK 16 Voltmeter BRN/YEL 10 RED/PUR 16 Engine Hatch Lift - see MFR Schematic M Water Pump 3A Stove - see MFR Schematic To House Battery YEL 10 WHT/ORG 16 Propane Sensor - see MFR Schematic Breaker Switch DPST Speaker Horn Light Switch DPDT Outlet 12V SYMBOL KEY Float Switch Description of unit Switch SPST Unit Switch SPST Off-(On) Motor M Level Sensor Prompt to Fuse + - A B C 30

31 RANGER TUG R-29 WIRING SCHEMATIC (LIGHTING) All Switched w/ House Battery Switch +12V Dash Fuse Block #1 Subpanel 8 Switch (Helm) 30A Subpanel 8 Switch 30A RED 10 (Helm) Chart LT RED 10 Nav/Inst RED 10 RED 10 RED 10 RED 10 R-29 Lighting ELECTRICAL SCHEMATIC Wipers (Port, Mid. & Stbd) To Acc. #1 Schematic Bilge Pump (#1) To Acc. #1-2 Schematic Bilge Pump (#2) To Acc. #1-2 Schematic Horn To Acc. #1 Schematic 10A BLU/ 10 A -12V GND GRY/RED 16 To Acc. #1 Schematic Nav AC/DC Panel Light - see MFR Schematic GRY/BLK 16 To Acc. #1 Schematic Anchor Compass V-berth LT 10A WHT/BLU 16 BLU/WHT 16 Rope LT BLU/ORG V Dash Fuse Block #2 10A Head LT BLU/PUR 16 Search LT (Remote) +12V 1A PDP Fuse Block 10A Misc LT RED 16 BLU/BRN 16 Search Light Remote - see MFR Schematic Quarter Berth LT ORG/PUR 16 Led Overhead BLU 16 (Rope LT) Cabin LT Subpanel 4 Switch (Deck) 10A Deck LT 20A Porch LT Underwater LT BLU/RED 16 RED 10 10A BLU/BLK 16 10A PUR/RED 16 RED 10 PUR/ 10A RED 10 GRY/BLU 16 Search LT 10A ORG 16 Search Light - see MFR Schematic 31

32 RANGER TUG R-29 WIRING SCHEMATIC (P.D.P.) To Bridge Fuse Block To Quarter Berth Fuse Block R-29 Power Distribution 50A 6 RED 6 RED 6 RED 50A 150A To Quarter Berth Engine Fuse Block To Quarter Berth Thruster Fuse Block To AC Panel ELECTRICAL SCHEMATIC 6 RED 1 RED 6 RED 6 RED HOUSE SWITCH ENGINE 2/O RED 300A To Generator Control Panel GENERATOR See Generator MFR Schematics. To AC Panel RED * Must have stern thruster battery switch on to start generator CHARGER/ INVERTER See Charger/Inverter MFR Schematics for wire and fuse size. - + To Thruster To Thruster 2/O RED 300A 2/O RED Jumper Bar SWITCH BOW THRUR 2/O RED See Thruster SWITCH MFR Schematic RN for fuse sizes. THRUR 1/O RED 1/O RED 2/O RED PARALLEL SWITCH SWITCH INVERTER Jumper Bar 2/O RED 4 YEL 6 RED Helm 6 RED 1 RED 6 RED Helm 6 YEL 1 YEL 6 YEL 2/O RED + STARTER To Fuse Block #1 To Fuse Block #2 To Windlass Relay To Windlass Relay To Dash Fuse Blocks 1/O RED 2/O RED SWITCH To Engine Schematic GND BUSS 1/O YEL Aft 2/O YEL 2/O RED To Engine Ground CHARGE RELAY CHARGE RELAY 2/O YEL 2/O YEL 1 RED 1 RED 2/O RED 1 RED 1 RED 2/O RED 1 2/O YEL 2/O RED 1 2/O YEL 2/O YEL 2/O YEL 2/O YEL THRURS ENGINE HOUSE 1 HOUSE 32

33 RANGER TUG R-29 WORKING DECK R-29 CB R-29 S 33

34 MAST SET UP AND TAKEDOWN MAST SET UP PROCEDURE 1. Remove the three black plastic wing nuts from the mast base. 2. Remove the two mast tie down cables from their storage positions in the roof clips. 3. With the mast tie down cables still loose, remove pin, raise the mast off of the stainless steel support bar. 4. Secure the stainless steel retaining bar in the appropriate clip attached, reinsert pin into mast fitting. 5. Raise the mast to its full extension and ensure that it fits correctly over the mounting studs on the roof mounting plate. 6. Attach the three black plastic wing nuts to the mounting studs and hand tighten securely. 7. Attach the two mast tie down cables to their appropriate clips on the port and starboard side of the roof. 8. Make sure the mast tie down cables are adjusted properly. MAST TAKE DOWN PROCEDURE 1. Remove the mast tie down cables from their clips on the port and starboard side of the roof. 2. Remove the three black plastic wing nuts from the mast base mounting studs. 3. Carefully lower the mast onto the stainless steel support bar and insert pin. 4. Attach the black plastic wing nuts back onto the screws on the mast mounting plate and secure them for storage by hand tightening. 5. Attach the two mast tie down cables to their storage positions in the roof clips. 6. Secure the mast with a tie down. 34

35 CARE AND MAINTENANCE The following checklists are examples and are not all inclusive and are provided only as a guide. Please customize to your personal needs. Consult your engine and trailer user manuals for additional information. EXAMPLE OF A PREPARATION FOR THE ROAD CHECKLIST TOW VEHICLE PRIOR TO USE Test Lights. Check brakes. Check tire pressure and condition. Check hitch related electrical connections. TRAILER PRIOR TO USE Check registration Check rollers and bed rails. Check wheel bearings and lubricate as required. Check winch. Test electrical connection and lights. Check tire pressure and condition. Check safety chains. Check boat straps. Check braking system. Check hitch for proper connection and lock down. Install safety chains (cross under hitch). Remove tire blocks. BOAT PRIOR TO USE WITH TRAILER Lower mast. Lower VHF antenna. Secure the Bimini awning frame. Raise and secure swim platform ladder. Set all switches and breakers to the OFF position, Including Thruster/Windlass cutoff switch Close and secure all windows, ports and vents. Lock cabin. Center rudder. Remove Drain Plug. Install windshield canvas to protect from rocks while traveling. 35

36 EXAMPLE OF A SPRING PRE-LAUNCH CHECKLIST CLEANING Remove debris from scuppers and scupper drains. Clean hull using a mild biodegradable detergent and then wax. Clean topsides and decks using a mild biodegradable detergent and then wax. Clean and polish all bright work. Clean and oil teak. Clean windows, ports, and hatches. Clean bimini cover. Check and clean anchor, rode, and anchor storage compartment. INSPECTION Check Drain Plug Check spare parts and tools and replace as necessary. Check wiper blades. Check swim platform. Inspect and test trim tabs. Check condition of bottom paint. Check windlass. Verify electronics for correct operation. Check all inside and outside lights. Macerator Y-Valve in proper position and secured. Inspect and verify position of all sea cocks and shut off valves. Check alarms for proper operation. Check fluid levels. Inspect batteries / water level in batteries (if applicable). Check bilge pump operation / clean float switches. SAFETY EQUIPMENT Sound signaling device. Check flares and their expiration dates. Check personal flotation devices. Check fire extinguishers and their fill dates. First aid kits. GALLEY Check stove for proper operation. Check everyday utensil stock. DOCUMENTS Registration sticker. Insurance papers and Passports. Boat Inspection sticker. Charts and float plan forms. 36

37 EXAMPLE OF WINTER STORAGE CHECKLIST GENERAL MAINTENANCE Fill Fuel Tank and add a fuel stabilizer. Empty and clean black water tank. Empty fresh water tank use a non-toxic antifreeze per manufacturer s directions. Winterize black and fresh water tanks as necessary based on weather. Check bilge area for oil and for proper operation / Check bilge pump operation / clean float switches. Check zincs and replace as necessary. Check impeller. Check and clean water strainer. Clear barnacles and debris from hull fittings. Trickle charge batteries every days. Vent boat to prevent mildew. Check trailer tire pressure and condition. Check trailer braking system. Check trailer bearings. Remove Drain Plug. Turn off all battery cutoff switches. ENGINE Flush sea strainer system with fresh water. Check all fluid levels. Check all hose fittings. Check engine maintenance requirements. Inspect and verify position of all sea cocks and shut off valves. GALLEY Empty, clean and freshen refrigerator. Remove all dry food from storage. 37

38 NOTES 38

39 NOTES 39

40 25802 Pacific Highway South Kent, Washington Phone Fax All rights reserved. Reproduction or translation by any means in whole or in part is not permitted without written authorization from Ranger Tugs. The information contained herein is correct to the best of Ranger Tugs knowledge and the contents may change without notice and without incurring obligation.