Ranger Tugs and Cutwater Boats Orientation Checklist

Transcription

1 Ranger Tugs and Cutwater Boats Orientation Checklist Boat Model: Owner's name: Delivery Captain: Date: DAY 1 Main Cabin: Main cabin components and functions Raising & Lowering the dinette table and bed configuration. Galley components and operation: sink, stove, refrigerator, microwave, wine cooler (if equipped) Head: Main components and functions Using the shower; shower drain box, location and maintenance, Shower drain box fuse location Verify tank level indicators on vessels equipped with Tecma toilet Using the toilet; operation and maintenance. Marine toilet paper only! DC Electrical: Battery locations (House, Engine, Thruster, Inverter) Battery type and maintenance Battery switch locations, operation of battery switches DC Voltmeter location; identify which bank is House, Engine and Thruster DC Voltmeter fuse locations; fuse size House breaker location and operation (how to reset breaker if tripped) Fuse panel locations and panel diagrams (switched vs. unswitched panels) 12 Volt outlet locations

2 DC Lighting: Main cabin light switch location Cockpit light switch location Quarter birth light switch location Cockpit light switch location V-berth light switch location Head light switch location Deck light switch Underwater lights switch location Switches on light fixtures Helm Switch Panel: Identify and explain the helm switches: windshield wipers, navigation & anchor lights, accessory (exhaust fans), docking lights, thruster remote switch AC Electrical: Connecting shore power plug location and operation ELCI breaker location and operation Shore power breaker panel location and operation Shore power rotary switch location and operation Shore power vs. inverter Shore power vs. generator Outlet locations, GFCI explanation and locations Inverter: (if equipped) Inverter components: battery, battery switch, fuse(s) size & locations, panel location Inverter operation; how to use the inverter; power management of the inverter (do not use for the battery charger or hot water heater) Inverter / Battery charger combination unit explanation and operation Charge Relays: Charge Relay location and function How to bypass a charge relay in case of voltage below 10.8 volts

3 Fuel Tank: Fuel fill, vent and tank location Fuel tank capacity Fuel shut off valve location and operation Fuel octane rating must be a minimum of 89 (Yamaha Only) Fuel stabilizers (gas)/biocides (diesel) during storage Potable Tank: Potable water fill, vent and tank location Potable water tank capacity Water pump switch location and operation (Turn pump off when boat is left unattended) Water pump and filter, location and maintenance Checking tank level Winterizing potable water components in case of freeze Waste Tank: Waste tank pump-out, vent and tank location Waste tank capacity Waste tank cleaning chemicals and when to pump-out Pump-out vs. overboard discharge Macerator function and location; overboard discharge through-hole location Correct position for macerator valve to meet coast guard requirements Macerator breaker/switch location; macerator operation. DO NOT RUN DRY Overboard discharge requirements Hot Water Heater: Hot water heater location and connections; periodically checking hose clamps (can loosen over time) Hot water heater operation from engine coolant Draining and winterizing the hot water heater tank

4 Propane Locker and Dunnage Box: Propane bottle location Operation of regulator and shut-off valve Gas can storage Rooftop: Mast raising and lowering procedures Mast cable adjustment Command bridge components/locations Command bridge raising and lowering procedures (Ranger 31' & Cutwater 30') VHF antenna raising and lowering procedures; handle adjustment Radar connections (shown where to add dielectric grease) Searchlight operation Solar Panel: Control panel location and operation Controller location and maintenance (keep dry) Volt meter vs. control panel voltage comparison (batt. 1 & 2) Charges batteries at 90% House and 10% Engine TV & Stereo: TV operation: playing DVD's, scanning for channels, changing the input, displaying engine information on TV Stereo operation: Adjusting volume by zone, included adapters, connecting Bluetooth devices, XM radio operation (if equipped) Anodes: Explain different types of anodes (Aluminum, Zinc and Magnesium) Bow and Stern thruster propeller zinc location and maintenance Trim tab zinc location and maintenance (if equipped) Transom zinc location (if equipped) Engine zinc(s) location (if equipped) Prop zinc location and service

5 Generator (if equipped): Seawater cooling system components and locations (sea water pick-up, ball valve, sea strainer, seawater pump, exhaust through-hole) Fuel system component locations (fuel filter, shut off valve) Oil filter location Zinc anode location and replacement Panel location. Generator start-up and shut-down procedure Air Conditioning (if equipped): Seawater cooling system components and locations (through-hole, ball valve, sea strainer, seawater pump, exhaust through-hole) Priming seawater pump Control panel location; Air conditioner start-up and shut-down procedure Heating: Engine coolant (waste heater) location and operation (if equipped). Engine ball-valve location, isolating coolant to engine in case of leak Webasto diesel heater; fuel shut-off valve and fuel pump location Webasto heater control panel location and operation (run hot) Raw Water Wash-down: Raw water wash-down components: seawater pick-up, sea strainer, ball valve, pump and switch location Wash-down pump filter location and maintenance Bimini / Full Enclosure / Canvas: Bimini setup & takedown (if equipped) Full enclosure setup & takedown (if equipped) Canvas window/door cover locations and fitment Canvas covers for table(s) / seat(s) (if equipped) Window curtain operation

6 DAY 2 Engine: Engine component description and locations: Seacock, seawater strainer, exhaust port, fuel shut-off valve, fuel in water separator Checking fluids (engine oil, transmission oil) / types of fluids used Engine shaft alignment procedure and service schedule (Inboard Only) Engine HCU (shifter)/control location and operation Switching between stations (if applicable) Engine display operation and menu information Displaying engine information on Garmin chart plotter Checking and recording engine faults Engine warranty should be registered to owner at the time of delivery PDI has to be complete for warranty registration to owner Packing Gland (Shaft Seal): Checking and adjusting the shaft packing nut Allowable amount of drip during operation Hydraulic Steering System: Self venting helm pump Indications of air in the system Hydraulic ram location & maintenance (keep clean) Auto-pilot pump to ram connection Thrusters: Panel and remote operation Battery switch / fuse locations How to access thruster motor(s) for inspection Shear pin replacement procedure Explanation of provided thruster tool

7 Electronics: Chart plotter breaker location (Ranger Tugs only) Checking fuel level (on engine and/or garmin display) / fuel calibration Creating a course on the Garmin display Auto Guidance features and settings Fusion radio operation and controls through Garmin. Significance of NMEA 2K Power How to access N2K communications to verify operation of various systems Transducer location; how to check fluid level on the transducer VHF radio location and operation. How to program MMSI Compass location (if applicable) Autopilot: Autopilot breaker location (Ranger Tugs only) Component location (hydraulic pump, ECU, compass) Autopilot operation. (Following routes, auto guidance & heading mode) Autopilot wireless remote operation & plotter operation Autopilot calibration explanation, when is it necessary to calibrate Trim Tab / Hydraulic Strut: Breaker location (Ranger Tugs only) Trim tab switch location and operation Checking pump fluid; adding ATF (with tabs in up position & engine hatch closed Engine hatch actuator (Ranger 29' and 31's, Cutwater 28' and 30's only) Trim tab maintenance & zincs Bilge Pumps / High Bilge Alarm / Carbon Monoxide Sensor: Bilge pump locations Automatic (Float switch) operation vs. manual switch operation Bilge pump float switch testing / cleaning procedure Clearing air locks from bilge pump Bilge pump fuse size and location High bilge water alarm switch and sensor location & testing High bilge water alarm fuse size and location Carbon monoxide Sensor location and operation Carbon monoxide sensor fuse size and location Cockpit Hatch & Compartment Drains: Explain cockpit hatch drains and through hole locations Locate compartment drain locations Suggest removing screens from cockpit drains Explain drain inspection and maintenance

8 Anchoring / Windlass: Helm switch and foot switch locations and operation Anchor launch and recovery demonstration Windlass breaker & thermal switch location and operation Manual turning the windlass with provided tool Demonstrate how to set an anchor with length vs depth. 5:1-7:1 scope Anchor rode total length Dinghy (if equipped): Dinghy Launch and Recovery Dinghy maintenance Trailering: Connecting and checking trailer lights Brake controller check and adjustment Launching and Recovery / Trailer Depth Trailer Maintenance Bottom Paint: Bottom paint maintenance and respray schedule Warranty Coverage & Maintenance Schedule: Ranger Tugs / Cutwater boats warranty coverage Warranty coverage begins: ; coverage ends: Engine warranty coverage Warranty coverage begins: ; coverage ends: Extended Engine warranty? Yes / No Winterization & Storage procedure's Maintenance schedules / Where to find schedule Serial Numbers: Engine Serial #: Engine shifter Serial # (outboard engine's only): Generator Serial # (if applicable): Air Conditioner Serial # (if applicable): Kicker motor Engine Serial #: Questions:

9 Notes: Customer's Signature: Captain's Signature: Date: Date: