FITTING INSTRUCTIONS BP TOYOTA LANDCRUISER 200 SERIES REAR

Size: px

Start display at page:

Download "FITTING INSTRUCTIONS BP TOYOTA LANDCRUISER 200 SERIES REAR"

Noel McBride
5 years ago
Views:

1 FITTING INSTRUCTIONS BP TOYOTA LANDCRUISER 200 SERIES REAR WARNING This product must be installed exactly as per these instructions using only the hardware supplied. In the event of damage to any suspension component, contact your nearest authorised ARB stockist. Repairs or modifications to the suspension system components must not be attempted. Do not use this product for any vehicle make or model, other than those specified by ARB. Do not remove labels from suspension components. This product or its fixing must not be modified in any way. The installation of this product may require the use of specialized tools and/or techniques It is recommended that this product is only installed by trained personnel These instructions are correct as at the publication date. ARB Corporation Ltd. cannot be held responsible for the impact of any changes subsequently made by the vehicle manufacturer During installation, it is the duty of the installer to check correct operation/clearances of all components Work safely at all times Note: These fitting instructions should be read in conjunction with the vehicle workshop manual. VM /01/2015

2 FITTING KIT CONTENTS Item Description Part No. Qty. 1 RESI MOUNT: LC200 REAR VE LSP 1L VE RSP 1R 2 MOUNT: RESERVOIR CLAMP VE SP 2 3 TOOL: ADJUSTER TOOL VC SP 1 4 WASHER: 19x46x2mm VE SP 2 5 WASHER: M6 BLACK VE SP 4 6 FASTENER: M6 NYLOC NUT VD SP 4 7 FASTENER: M6x1.0X16 BOLT VD SP 4 PIN MOUNT BUSH KIT CONTENTS (VM SP) Item Description Part No. Qty. A MOUNT: SLEEVE VF B FASTENER: M12 NYLOC NUT VD C WASHER: 12x28x3mm VE D WASHER RETAINING VF E WASHER LOCATING VF F WASHER RETAINING VF G BUSH NR VD NOTE: THIS PIN MOUNT BUSH KIT IS INCLUDED IN THE BP-51 SHOCK ABSORBER. VM /01/2015

3 DAMPER PREPARATION The new BP-51 needs to be prepared with mounting components before it is fitted to the vehicle. Top Mount Fit the crush tube to the pin. Ensure it is pushed all the way to the bottom of the pin. Fit the retaining washer bush and locating washer to the pin. Left and Right are the same. Refer to the next step for mounting the damper to the vehicle. Bottom Mount On the shaft guard clamp loosen one of the two M4 cap screws that secure the clamp to the eyelet. It is best to remove the screw that will be accessible after the damper is fitted to the vehicle. The diagram shows the screw that is best loosened for left hand damper fitment. Do not loosen the M8 cap screws that secure the guards to the clamp. Slide the guard and clamp assembly up off the eyelet so that the bottom mount can be accessed. VM /01/2015

4 DAMPER MOUNTING SEQUENCE The BP-51 needs to be fitted with the suspension in droop. Before fitting the damper fit the 2mm washer to the bottom mount as shown by the diagram. Mount the BP-51 dampers using the hardware in the sequence as shown. Top Mount Fit the damper to the vehicle top mount first. Fit the locating washer, bush, retaining washer, 12mm flat washer and secure with the nut as shown by the diagram. The nyloc nut should be firmly secured against the crush tube. Fit the top mount such that the hose leaving the damper is pointing towards the centre rear of the vehicle (towards the towbar). Ensure all top and bottom mounting hardware is securely fastened. Bottom Mount Ensure the new 2mm flat retaining washer is in place then fit the damper and secure with the original hardware. Refit the shaft guard assembly to the eyelet. To aid fitment place a flat blade screwdriver between the two halves of the clamp to spread them a little so that the clamp assembly can be refitted over the eyelet. Securely fasten the M4 cap screw to clamp the two halves of the clamp assembly to the eyelet. VM /01/2015

RESERVOIR MOUNTING SEQUENCE LEFT RIGHT Remove bolts securing sway bar link bracket to chassis.

bent down from the chassis. 36 (27) Fit M6 reservoir mounting hardware to the mounting bracket, finger tight only.

Fit the reservoir clamp to the reservoir then slide the assembly over the heads of the bolts in the bracket.

5 RESERVOIR MOUNTING SEQUENCE LEFT RIGHT Remove bolts securing sway bar link bracket to chassis. Fit reservoir mounting bracket between the sway bar link bracket and the chassis and secure using the original hardware. Torque to 37 N.m (27 ft.lbf). Mount such that the arrow on the bracket points to the front of the vehicle and the face with holes for mounting the reservoir is bent down from the chassis. 36 (27) Fit M6 reservoir mounting hardware to the mounting bracket, finger tight only. There should be no washer on the head side of the bolt. Use the washer supplied on the nut end. Fit the reservoir clamp to the reservoir then slide the assembly over the heads of the bolts in the bracket. The edge of the mounting clamp should be parallel with the edge of the bracket mm Ensure the reservoir clears the body of the damper and that the hose has a clean arc with no kinks and clears the coil spring. Note position of reservoir to clamp shown by the photos as a guide. Fasten hardware securely and torque where specified. VM /01/2015

6 SPECIFICATIONS AND SPARE PARTS 1 Spare Part: Top Bush Kit VM SP 2 Spare Part: Hose VD SP 3 Spare Part: Oil VC SP 4 Specification: Nitrogen Pressure 2000 kpa 5 Specification: Factory Rebound Setting 7 6 Specification: Factory Compression Setting 4 7 Spare Part: Valve Cap VD SP 8 Spare Part: Stone Guard VD SP 9 Spare Part: Steel Stone Guard In kit below 10 Spare Part: Stone Guard Mount Kit VM SP 11 Spare Part: Bottom Bush VD SP 12 Spare Part: Damper Mounting Kit VM DAMPING ADJUSTMENT These dampers have been set in the factory to be used for a vehicle with accessories fitted. If your load or accessory fitment differs, use the table below as a guide for recommended compression (Comp) and rebound (Reb) adjuster settings. Refer to the Owner s Manual for more information. Rear Load Comp Reb kg kg kg VM /01/2015

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag. Part Number: 36030 Product Description: BULL BAR WINCH TYPE Suited to vehicle/s: CHEVROLET C/K 500-3500 988-998 YEAR MODEL RANGE AND Warn 9,500-5,000lb WINCHES WARNING REGARDING VEHICLES EQUIPPED WITH