Pressure sensors. For pressures up to 1800 bar (180 Mpa)
|
|
- Ashley Henry
- 5 years ago
- Views:
Transcription
1 B A Pressure sensors 45 Pressure sensors or pressures up to (18 Mpa) Ratiometric signal evaluation (referred to supply voltage). elf-monitoring of offset and sensitivity. Protection against polarity reversal, overvoltage, and short circuit of output to supply voltage or ground. High level of compatibility with media since this only comes into contact with stainless steel. Resistant to brake fluids, mineral oils, water, and air. Application Pressure sensors of this type are used to measure the pressures in automotive braking systems, or in the fuel-distributor rail of a gasoline direct-injection engine, or in a diesel engine with Common Rail injection. esign and function Pressure measurement results from the bending of a steel diaphragm on which are located polysilicon strain-gauge elements. These are connected in the form of a Wheatstone bridge. This permits high signal utilisation and good temperature compensation. The measurement signal is amplified in an evaluation IC and corrected with respect to offset and sensitivity. At this point, temperature compensation again takes place so that the calibrated unit comprising measuring cell and AIC only has a very low temperature-dependence level. Part of the evaluation IC is applied for a diagnostic function which can detect the following potential defects: racture of a bonding wire to the measuring cell. racture anywhere on any of the signal lines. racture of the bridge supply and ground. Only for 5 5 This sensor differs from conventional sensors due to the following diagnostic functions: Offset errors Amplification errors can be detected by comparing two signal paths in the sensor. torage conditions Temperature range...+ C Relative air humidity...8 % Maximum storage period 5 years Through compliance with the above storage conditions, it is ensured that the sensor functions remain unchanged. If the maximum storage conditions are exceeded, the sensors should no longer be used. Characteristic curve. U A = (.8 p / p Nom. +.1)U V Output voltage U A V Explanation of symbols U A Output voltage U V upply voltage bar Pressure bar Pressure p
2 4 Pressure sensors A B Pressure sensors (contd.) or pressures up to (18 MPa) elf-monitoring. Offset and sensitivity. Only for 5 5. U A U V 9% 9% 1 % 4% Error band Limitation, working signal Measuring range Error range Error band Measuring circuit. Pressure sensor 1 % Pressure p Offset error ensitivity error Error range ECU + 5 V (U V ) Pull up resistor ignal (U A ) A/converter and C iagnostic function during self-test (following switch-on). Only for 5 5. Correctness of the calibration values unction of the sensor signal path from the sensor to the A/ converter of the evaluation unit Check of the supply lines. iagram: Characteristic of the output voltage following switch-on unction of the signal and alarm paths etection of offset errors etection of short circuits in wiring harness etection of overvoltage and undervoltage If an error is detected during the sensor s self-test, the signal output is switched to the voltage range > 9%U V. iagnostic function during normal operation. Only for 5 5. etection of offset errors etection of sensitivity errors (with pressure applied) Wiring-harness function, detection of wiring-harness short circuits etection of overvoltage and undervoltage If an error is detected during the sensor s self-test, the signal output is switched to the voltage range >9%U V. 1 GN Range Pressure range ensor Thread Connector Pin imens. Page Part number bar (MPa) Type drawing 14 (14) KV BE M 1x1 Compact 1.1 Gold-plated (5) M 1x1 PA (15) R M 1x1.5 Working circuit ilber-plated M 1x1.5 Compact 1.1 Gold-plated R M 1x1.5 Working circuit ilber-plated M 1x1.5 Compact 1.1 Gold-plated (18) R M 1x1.5 Compact 1.1 Gold-plated M 18x1.5 Compact 1.1 Gold-plated R M 18x1.5 Compact 1.1 Gold-plated M 18x1.5 Working circuit ilber-plated Accessories or 5 5 Plug housing Quantity required: 1 AMP No ) Contact pins for.5 mm Quantity required: AMP No ) Gaskets for mm Quantity required: AMP No ) 1 ) To be obtained from AMP eutschland GmbH, Amperestr. 11, -5 Langen, Tel. 1 / 9-, ax 1 / 9, AMP.Kontakt@tycoelectronics.com
3 B A Pressure sensors 4 Technical data Pressure sensor Pressure-sensor type KV BE R R R R Application/Medium Unlead. fuel Brake fluid iesel fuel or iesel fuel or iesel fuel or iesel fuel or RME 1 ) RME 1 ) RME 1 ) RME 1 ) Pressure range bar (MPa) (14) (5) (15) (15) (18) (18) Offset accuracy U V. %. % 1. %. % 1. %. % 1.5 % ensitivity accuracy at 5 V In range...5 bar ). % 1. %. % 1. %. % of 1.5 % In range bar meas- 1.5 % In range bar ured 5. % ) In range 5... value. % 1.5 %.5 % In range 5....% 1.5% Input voltage, max. U s V Power-supply voltage U V V 5 ±.5 5 ±.5 5 ±.5 5 ±.5 5 ±.5 5 ±.5 Power-supply current I V ma Output current I A µa...ma ma 4 ).5 ma 4 ) Load capacity to ground n 1 1 Temperature range C ) ) Overpressure max. p max bar Burst pressure p burst bar > > Tightening torque M a Nm ± ± 5 ±5 5 ±5 ± ± Response time T 1/9 ms 5 5 Note: All data are typical values 1) RME = Rapeseed methyl ester ) = ull cale ) Of measured value 4 ) Output current with pull-up resistor 5) +14 C for max. 5 h imension drawings pace required by plug, approx. 5 mm pace required when plugging/unplugging, approx. 5 mm W = A/ size bar W ±, 5, ± ±,1 ø 8,5 ø,8 1,5 59,8,8 Ground Pin Output voltage U A upply voltage U V Pin ø 5 9 4,4 M 1x1-g 1,5 ±
4 48 Pressure sensors A B Pressure sensors (contd.) or pressures up to (18 MPa) imension drawings pace required by plug, approx. 5 mm pace required when plugging/unplugging, approx. 5 mm W = A/ size Gasket ate of manufacture -pin plug Ground Pin Output voltage U A upply voltage U V bar W 4 1 ±,1 41 B 4, A 5, 8 ±,,9 ±,5 1,1 ±,,8 -,5 Pin ø5 -,1 M1x1 9 ø,1 1 ø8,5 -,1 ø,8 ±,1 15, ±,1 5, ±, 81 8 W R 1,5 9 ± Pin ø 5 M 1x1,5, -,1 1,5 1 9 ± W R 1,5 9 ± Pin ø 5 4,4 M 1x1,5, -,1 1,5 1 8 ± W 1,5 ± ±,5 Pin ±,1 ø 4,8 M 1x1,5,15 ±,15 1,5 1, ±,,5 ±
5 B A Pressure sensors 49 imension drawings pace required by plug, approx. 5 mm pace required when plugging/unplugging, approx. 5 mm W = A/ size Gasket ate of manufacture -pin plug Ground Pin Output voltage U A upply voltage U V 81 5 W 1,5 ± R 1 Pin ø 5 4,4 M 1x1,5-g, -,1 1,5 ± 1 59, ± 81 4 ø 5 W M 18x1,5-g ø1,,8-9 ± Pin 4,4 1,1 9 ± ,1 1,5 ± ø 5 W M 18x1,5-g ø1, 15 Pin 4,4,5,4 ± ,1 1,5 ± ø 5 W M 18x1,5-g ø1, 15 Pin,5,8 ±
SSI Technologies Application Note PS-AN2 MediaSensor Absolute & Gage Pressure Transducers & Transmitters Product Overview
Product Description The MediaSensor (P51) family of bulk micro-machined, absolute, gage and sealed pressure transducers and transmitters are for both harsh and benign media with the superior typical accuracy
More informationPressure Transmitters
Transmitters Wetted parts are all made of stainless steel for high resistance to chemicals Stainless steel diaphragm welded with casing No seals and thus low leakage rate even with difficult gases High
More informationMountable with O-ring seal Urea level ±0.5% Accuracy Urea pressure ±2.0 Total Error Band Air Brakes Corrosive fluid measurement for E&V applications
Mountable with O-ring seal Stainless Steel wetted surfaces Amplified ASIC calibrated Absolute, sealed gage Cable option Analog output DESCRIPTION The U86B is a small profile, media compatible, piezoresistive
More informationSeal material. Pressure range. Pressure connection -40 F +212 F 1 -4 F +257 F 3
0675 / 0680 / 0690 Order matrix for pressure transmitters in Oil-Filled Housing ype Pressure range Pressure connection Seal material Electrical connection 0.5 4.5 V, ratiometric 0675 0 10 V, -wire 0680
More information6.5th-Generation Automotive Pressure Sensors
6.5th-Generation Automotive Pressure Sensors UZAWA, Ryohei * NISHIKAWA, Mutsuo * TANAKA, Takahide * A B S T R A C T There is increasing demand for reducing the environmental load of automobiles. Automotive
More informationSSI Technologies Application Note PS-AN7 MediaGauge (Model MG-MD) Digital Pressure Gauge Product Overview
Product Description The MediaGauge MG-MD is a multi-functional digital pressure gauge consisting of a media isolated piezoresistive pressure sensing element, signal conditioning circuitry for temperature
More informationElectronic Pressure Switches
96 Pressure Switches Electronic Pressure Switches Electronic E.5 switching output Electronic pressure switches, High-Performance series with one switching output Outstanding overpressure protection (up
More informationSSI Technologies Application Note PS-AN4 MediaGauge (Model MG-9V) Digital Pressure Gauge Product Overview
Product Description The MediaGauge Model MG-9V digital pressure gauge is a stand alone 9V battery operated multi-functional digital pressure gauge. The MG-9V digital pressure gauge contains a media isolated
More informationPressure transmitters for heavy duty applications MBS 8200 and MBS 8250
Data sheet Pressure transmitters for heavy duty applications MBS 8200 and MBS 8250 MBS 8200 is a series of compact pressure transmitters developed to withstand the pressure pulsations and vibrations known
More informationSSI Technologies Application Note PS-AN4 MediaGauge (Model MG-9V) Digital Pressure Gauge Product Overview
Product Description The MediaGauge Model MG-9V digital pressure gauge is a stand alone 9V battery operated multi-functional digital pressure gauge. The MG-9V digital pressure gauge contains a media isolated
More informationSteering column and sensor
Steering column and sensor Type LAB Series 1 x Nominal voltage 12 to 48 volt Output signal digital, analog and direction (option) HE 11874 / 09.2017 2 LAB HE 11874 / 09.2017 Page Content 4 4 5 6 7 7 8
More informationTips & Technology For Bosch Partners
Tips & Technology For Bosch Partners Current topics for successful workshops No. 66/2013 Electrics / Electronics Sensors Applications and Features The Bosch sensors program offers over 2 100 different
More informationElectronic Pressure Switches
96 Pressure Switches Electronic Pressure Switches Electronic Electronic pressure switches, series, Very attractively priced electronic pressure switches, particularly for high volume deployment High overpressure
More informationEB100 High Accuracy Miniature Pressure Transducer
Miniature design (body ø11 mm) High Accuracy EMI Protected per CE Compliance Wide Temperature Range Absolute DESCRIPTION The EB100 pressure transducer is the smallest design proposed by MEAS from the UltraStable
More informationAdjustment range. Seal material. Pressure connection
0520 Order matrix for electronic pressure switches.3 Type Adjustment range Pressure connection Seal material lectrical connection Type lectronic pressure switch 0520 Adjustment range 1) for NO 0 145 psi
More informationElectronic Pressure Switch EDS 3000
Description: The EDS 3000 is a compact, electronic pressure switch with integral digital display. The unit can have one or two switching outputs, and there is the option of an additional analogue output
More informationElectronic Pressure Switches
96 Pressure Switches Electronic Pressure Switches Electronic E.6 2 switching outputs Electronic pressure switches, High-Performance series with two switching outputs Outstanding overpressure protection
More informationElectronic Pressure Switches
96 Pressure Switches Electronic Pressure Switches Electronic E. Electronic pressure switches, series, Very competitively priced electronic pressure switches High overpressure protection (up to x) Small,
More informationSSI Technologies Application Note PS-AN3 MediaGauge Digital Pressure Gauges Product Overview
Product Description The MediaGauge digital pressure gauges have better accuracy, longer life and standard multiple functions which make it a better choice than mechanical pressure gauges. The MediaGauge
More informationMELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c
MELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c Voltage output The K7 Performance Level c series of Gefran are pressure transmitters for using in high temperature environment. The main characteristic
More informationMS4515 SPECIFICATIONS FEATURES APPLICATIONS
. SPECIFICATIONS PCB Mounted Pressure Transducers Pressure Ranges from 2 to 30 inches H 2O Amplified Ratiometric Analog Output Differential & Gage Temperature Compensated 3.3V or 5.0 V DC Supply Voltage
More informationMELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c
MELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c Voltage output The K7 Performance Level c series of Gefran are pressure transmitters for using in high temperature environment. The main characteristic
More informationMS4525 SPECIFICATIONS
SPECIFICATIONS PCB Mounted Pressure Transducers Amplified Ratiometric Analog Output Differential, Gage, Absolute, Compound, & Vacuum Temperature Compensated 3.3 or 5.0 Vdc Supply Voltage The MS4525 is
More informationPressure transducer DMU 01K Compact version
Pressure transducer DMU 01K Compact version Dimensions (in mm) Wiring diagram 8 Application Special OEM unit. For electronic pressure measurement in industrial or HVAC applications (such as hydraulic,
More informationDCT 533. Industrial Pressure Transmitter with IO-Link Interface. Stainless Steel Sensor
DCT 5 Industrial Pressure Transmitter with IO-Link Interface Stainless Steel Sensor accuracy according to IEC 60770: standart: ± 0.5 % FSO sption: ± 0.5 % FSO Nominal pressure from 0... 00 mbar up to 0...
More informationBODAS Pressure sensor PR3 series 10
BODAS Pressure sensor PR3 series 10 RE 95155 Edition: 04.2014 Replaces: 12.2013 Measurement ranges to 25, 50, 160, 200, 250, 400, 600 bar Ratiometric output signal 0.5 to 4.5 V with 5 V supply voltage
More informationSolid State Electronic Pressure Switch with Integral LED Display Model PSD-10
Solid State Electronic Pressure Switch with Integral LED Display Model PSD-10 Electronic Pressure Measurement WIKA Datasheet PSD-10 Applications Hydraulics and pneumatics Filter monitoring Pump control
More informationDMP 333. Industrial Pressure Transmitter For High Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter For High Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO Nominal pressure from 0... 00 bar up to 0... 600
More informationMBS 1200 and MBS 1250
Data sheet OEM Pressure Transmitters for heavy-duty applications MBS 1200 and MBS 1250 The compact OEM pressure transmitter programme is designed for use in severe hydraulic applications. The programme
More informationOEM Pressure Transmitters for heavy-duty applications Type MBS 1200 and MBS 1250
Data sheet OEM Pressure Transmitters for heavy-duty applications Type MBS 100 and MBS 150 The compact OEM pressure transmitter programme is designed for use in severe hydraulic applications. The programme
More informationPRESSURE MONITORING.
MONITORING PRESSURE MONITORING PRESSURE Pressure-control systems overview Technical explanations From page 8 Selection matrix Support for selection of suitable pressure switch Page 10 Pressure switches
More informationHigh temperature pressure transmitters for heavy-duty applications MBS 2200 and MBS 2250
Data sheet High temperature pressure transmitters for heavy-duty applications MBS 2200 and MBS 2250 The compact heavy duty pressure transmitter type MBS 2200 and MBS 2250 are designed for use in severe
More information0190 / Tolerance in psi (bar) at room temperature. Adjustment range in psi (bar) psi. ± 2.90 psi. (± 0.2 bar) (0.3-1.
0190 / 0191 Diaphragm / piston pressure switches up to 24 V with gold contacts Zinc-plated steel (CrVI-free), with spade terminal Snap action with gold contacts Overpressure safety up to 1,450 / 4,350
More informationBeck. The differential pressure transmitter for air with IP65
Beck. The differential pressure transmitter for air with IP65 Differential pressure transmitter 985 with IP65 General description The differential pressure transmitters of the 985 series are used to measure
More informationPressure transmitter for industrial applications Type MBS 4510
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for industrial applications Type MBS 4510 The high accuracy flush diaphragm pressure transmitter MBS 4510 is designed for use in non-uniform,
More information产品技术规范. Product Name: Product Technical Specification SMARTSTONE. No.: CPFL0002 Version: A Issued date: Page 1 of 16
Product Name: TMAP Part Number: CPF00002 Drawing Number: CPFJ0002 Page 1 of 16 CONTENTS 1. General Data 1.1. Description 1.2. Installation Guide 1.3. Maximum ratings of pressure sensor 1.4. Operating characteristics
More informationPressure switch hex 27
Pressure switch Changeover switch with silver or gold contacts Easily adjustable switching point. Factory adjustable hysteresis (except type 0140/014. High overpressure safety and long life even under
More information1/4 BSPP. 500 psi / 35 bar) psi / 35 bar) 8 018X XXX 03 X XXX
0186 / 0187 Diaphragm / piston pressure switches up to 250 V with stainless steel housing M.4 Stainless steel housing (AISI 303 / 1.4305) Snap action with silver contacts Overpressure safety up to 4,350
More informationPressure transmitters for industrial applications Type MBS 4510
Pressure transmitters for industrial applications Type MBS 4510 Technical brochure Features Designed for use in severe industrial environments Enslosure and wetted parts of acid-resistant stainless steel
More informationDMP 331 DMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor. Pressure Transmitter. Industrial
TEMATEC GmbH Postal address: House address Fon (+49) 0 4-870-0 Postbox 6 Löhestr. 7 Fax (+49) 0 4-870-0 http: // www.tematec.de 5759 Hennef 577 Hennef e-mail: team@tematec.de TEMATEC GmbH Data Sheet DMP
More informationLoad Cell for Manually Operated Presses Model 8451
w Technical Product Information Load Cell for Manually Operated Presses 1. Introduction... 2 2. Preparing for use... 2 2.1 Unpacking... 2 2.2 Using the instrument for the first time... 2 2.3 Grounding
More informationDMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter for Low Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO Nominal pressure from 0... 00 mbar up to 0... 40
More informationData Sheet P992 Low Range Differential Pressure Sensor
Data Sheet P992 Low Range Differential Pressure Sensor Main Features Pressure Ranges Electrical Connection Pressure Connection Housing Material Output Signal 1, 2, 5, 10, ±1, ±2, ±5 Inches of H2O Options
More informationPressure Transmitter. Pressure transmitter with compact design Model EDC-K. Electronic. Applications. Special Features.
Pressure transmitter with compact design Electronic Pressure Transmitter Applications Mechanical engineering Machine tools Control and feedback control systems Hydraulics / Pneumatics Pumps/ Compressors
More informationDMK 331P. Industrial Pressure Transmitter. Pressure Ports With Flush Welded Stainless Steel Diaphragm. accuracy according to IEC 60770: 0.
DMK P Industrial Pressure Transmitter Pressure Ports With Flush Welded Stainless Steel Diaphragm accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 60 bar up to 0... 400 bar Output signals
More informationMAP Sensor. Technical Spec COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED ECOTRONS LLC. -Manifold Absolute Pressure Sensor
MAP Sensor -Manifold Absolute Pressure Sensor Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com.
More informationInnovation in pressure sensing Simple-to-set compact electronic pressure switches. Pressure switches
Innovation in pressure sensing Simple-to-set compact electronic es Pressure switches PK es with mechanical adjustment dials provide simple setup Extremely durable The PK features a 316 stainless steel
More informationDM01. Battery Powered Precision Digital Gauge. Stainless Steel Sensor. class 0.05
Battery Powered Stainless Steel Sensor class 0.05 Nominal pressure from 0 00 mbar up to 0... 00 bar Special characteristics modular sensor concept data logger graphic display stainless steel housing Ø
More informationDL 01. Battery Powered Precision Digital Gauge for Leak Testing. Stainless Steel Sensor. class 0.05
DL 0 Battery Powered for Leak Testing Stainless Steel Sensor class 0.05 Nominal pressure from 0 00 mbar up to 0... 00 bar Special characteristics modular sensor concept data logger graphic display stainless
More informationPressure transmitters for heavy-duty applications MBS 2000 and MBS 2050
Data sheet Pressure transmitters for heavy-duty applications MBS 2000 and MBS 2050 The compact heavy duty pressure transmitters MBS 2000 and MBS 2050 are designed for use in hydraulic applications. MBS
More informationSSI Technologies MediaSensor
SSI Technologies MediaSensor P51 Pressure Transducers Product Description SSI s line of bulk micro-machined, absolute and gage pressure transducers and transmitters for both harsh and benign media with
More informationData Sheet P6000 Remote Mount Miniature Pressure Sensor
Data Sheet P6000 Remote Mount Miniature Pressure Sensor Main Features Electrical Connection Pressure Connection Housing Material Output Signal 0 to 2.5 up to 0 100 PSI and 0 to 200 mbar up to 0 to 7 Bar
More informationThermal flow sensor TFS-35
průmyslová elektronika Thermal flow sensor TFS-35 For sensing limit flow rates of fluid media and for monitoring their temperature. These sensors are intended for installation in pipes, in which the actual
More informationPiezoresistive Absolute Pressure Sensors
Pressure Piezoresistive Absolute Pressure Sensors Universal Precision Pressure Sensors Type 4043A..., 4045A..., 4073A..., 4075A... Universal sensor suitable for measuring absolute pressures in ranges from
More informationDMK 331P DMK 331P. Industrial Pressure Transmitter. Pressure Ports With Flush Welded Stainless Steel Diaphragm. Pressure Transmitter.
TEMATEC GmbH Postal address:: Postbox 6 House address Löhestr. 7 5759 Hennef 577 Hennef Fon (+49) 0 4-87 0-0 Fax (+49) 0 4-87 0-0 http: // www.tematec.de e-mail: team@ tematec.de TEMATEC GmbH Data Sheet
More informationType A-10 General Purpose Pressure Transmitters
Type A-10 General Purpose Pressure Transmitters Applications Mechanical engineering Machine tools Process control and automation Hydraulics and pneumatics Pumps and compressors Special Features Pressure
More informationMPM160 Pressure Sensor
MPM160 Pressure Sensor Features Ranges: 0kPa~7kPa 700kPa MEMS Technology Gauge SOP or DIP package For non-corrosive gas Pressurize from back side Optional for pin direction Applications For medical fields,
More informationThermal flow sensor TFS-35
průmyslová elektronika Thermal flow sensor TFS-35 For flow monitoring rates of liquids media and for monitoring of their temperature These sensors are intended for installation in pipes, in which the actual
More informationPRESSURE TRANSDUCERS. Specifications. Individual Specifications
GEMS COMPLIANT 00 Series and 00 Heavy Duty Series Compact OEM Pressure Transmitters 0 00 psi to 0-0,000 psi ranges (0- bar to 0-,00 bar) High Proof Pressures Broad Choice of Outputs RoHS Compliant For
More informationProportional pressure relief valve Type DBETRE
RE 9 68/.99 Proportional pressure relief valve Type DBETRE Nominal size 6 Series X Max. operating pressure 5 bar Max. flow up to L/min H/A/D 67/99 Type DBETRE-X/ G4KA with integrated control electronics
More informationOEM Pressure transmitter for industrial applications Type MBS Technical brochure
OEM Pressure transmitter for industrial applications Type MBS 1200 Technical brochure Features Designed for use in severe industrial OEM applications For medium and ambient temperatures up to 125ºC All
More informationCD34CNFLFxxx. Capacitive sensor, Foreground Suppression. Main features. Main functions. Description
Capacitive sensor, Foreground Suppression Main features Compact housing Supply voltage: 10 to 30 VDC Output: 100 ma, NPN or PNP preset Make or break switching function LED indication for output and power
More informationOEM pressure transmitter with thin-film technology For mobile hydraulics Model MH-2
Electronic pressure measurement OEM pressure transmitter with thin-film technology For mobile hydraulics Model MH-2 WIKA data sheet PE 81.37 Applications Load monitoring Load moment limitation Hydraulic
More informationPRESSURE BENCH OPERATING INSTRUCTIONS
PRESSURE BENCH OPERATING INSTRUCTIONS Overview: The pressure bench system allows the user to apply a variety of calibrated pressures to a variety of high and low pressure transducers. In addition the system
More informationIndustrial Pressure Transmitters
Industrial Pressure Transmitters Type S-10, S-11 Applications Hydraulics and pneumatics Test equipment Pump and compressor control Liquid level measurement Special Features Standard ranges available from
More informationEPI Applications. Features
EPI 887 Industrial Pressure Transmitter Swiss based Trafag is a leading international supplier of high quality sensors and monitoring instruments for measurement of pressure and temperature. The industrial
More informationTechnical Datasheet P-30/P-31. Standard transmitter.
Technical Datasheet P-/P-1 Standard transmitter www.envec.endress.com two-wire technology 4 2 ma three-wire technology 1 V measuring element with poly-silicon thin-film strain gauge,hence: -no moving mechanical
More informationOperating instructions Electronic level sensor LK7 / LK /07 04/2006
Operating instructions Electronic level sensor LK7 / LK0 70593/07 04/2006 Contents enu structure 3 2 Controls and visual indication 4 3 Function and features 4 3. easuring range 5 3.2 Offset 5 3.3 Applications
More informationModel 6A Series 6-Axis Load Cells (Fx Fy Fz Mx My Mz)
6AXX 10-20 - 17 Model 6A Series 6-Axis Load Cells (Fx Fy Fz Mx My Mz) Interface s 6-axis load cell measures forces simultaneously in three mutually perpendicular axes and three simultaneous torques about
More informationPRESSURE SENSORS CPS 1184 CPS 2184 SPS 1000 Z SPS 3003 LEADING IN SENSORS
PRESSURE SENSORS CPS 1184 CPS 2184 SPS 1000 Z SPS 3003 LEADING IN SENSORS 2 LEADING IN SENSORS TRUST THE X! Fair partnership and customer-specific solutions. Every single one of our premium products offers
More informationBODAS Pressure sensor PR4 series 10
BODAS Pressure sensor PR4 series 10 RE 95156 Edition: 12.2015 Measurement range 0 to 280 bar 0 to 420 bar and 0 to 600 bar Ratiometric output signal 0.5 to 4.5 V with 5 V supply voltage Type of protection
More informationPRESSURE SENSORS First in sensors
PRESSURE SENSORS First IN SENSORS 2 First IN SENSORS TRUST THE X! Welcome to Metallux USA, Inc. Metallux USA, Inc. is the sole distributor of products for Metallux AG in Germany. A company that is internationally
More informationJUMO MIDAS S06. OEM-Pressure Transmitter Low Pressure. Applications. Brief description. Customer benefits. Special features
Delivery address: Mackenrodtstraße 609 Fulda, Germany Postal address: 605 Fulda, Germany Phone: +9 66 600-0 Fax: +9 66 600-607 Harlow, Essex CM 0 DY, UK Phone: + 79 6 55 Fax: + 79 6 50 9 67 Myers Road
More informationDMK 331P. Industrial Pressure Transmitter. Pressure Ports With Flush Welded Stainless Steel Diaphragm
Industrial Pressure Transmitter Pressure Ports With Flush Welded Stainless Steel Diaphragm accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 60 bar up to 0... 400 bar Output signals
More informationPressure transmitter for general purpose Type MBS 1700 and MBS 1750
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for general purpose Type MBS 1700 and MBS 1750 The compact pressure transmitters MBS 1700 and MBS 1750 are designed for use as a general purpose
More informationSafety Sensor CSS 180 Product Information
Safety Sensor CSS 180 Product Information Safety Sensor CSS 180 CSS180CSS 180 PDF-M / EN 60947-5-3 EN 954-1 Control Category 4 IEC 61508, suitable for use in SIL 3 applications BG Type-Certification in
More informationMore Precision. mainsensor Magneto-inductive displacement sensor
More Precision mainsensor Magneto-inductive displacement sensor mainsensor Magneto-inductive sensors for non-contact linear displacement measurement Measuring principle mainsensor is based on an innovative
More informationTension and Compression Load Cell Model 8435
Technical Product Information w Tension and Compression Load Cell 1. Introduction... 2 2. Preparing for use... 2 2.1 Unpacking... 2 2.2 Using the instrument for the first time... 2 2.3 Grounding and potential
More informationData Sheet P4000 Hermetically Sealed Pressure Sensor
Data Sheet P4000 Hermetically Sealed Pressure Sensor Main Features Pressure Ranges Electrical Connection Pressure Connection 0 to 100 up to 0 to 5000 PSI Packard Electric Metri-Pack 150 Series, Deutsch
More informationSEAT BELT LOAD CELL. Load cell that measures the forces at the seat belt during automotive crash or sled tests.
SEAT BELT LOAD CELL Load cell that measures the forces at the seat belt during automotive crash or sled tests. Lightweight and durable design High accuracy User replaceable cable Easy attachment of seat
More informationSPT- I / U PRESSURE TRANSMITTER for general applications
Fields of application Design Examples Hydraulics Air conditioning and heating Testing technology Industrial robots Process controlling Water technology Pneumatics Description The pressure transmitters
More informationPressure transmitter for industrial applications Type MBS 4500
MAKING MODERN LIVING POSSIBLE Data sheet Pressure transmitter for industrial applications Type MBS 4500 The high accuracy pressure transmitter MBS 4500 is designed for use in almost all industrial applications,
More informationVoltage Output MELT PRESSURE TRANSMITTERS IN SERIES TECHNICAL SPECIFICATIONS
MELT PRESSURE TRANSMITTERS IN SERIES Voltage Output The IMPACT series of Gefran, are pressure transmitters, without transmission fluid, for using in High temperature environment (350 C). Medium pressure
More informationOBE (On-Board Electronics) Type Direct Operated Linear Servo Valves (Size: 01 & 03) LSVG-01-EH-*-**-**-10, LSVG-03EH-*-**-**-10/1006
NO. 10 01E September 1, 2010 Public Relations Group Products Publicity Section Sales Administration Department Hamamatsucho Seiwa Bdg., 4-8, Shibadaimon 1-chome, Minato-ku, Tokyo 105-0012, Japan Tel: +81-3-3432-2113
More informationPressure Transmitter for wind turbine applications MBS 8200 and MBS 8250
Data sheet Pressure Transmitter for wind turbine applications MBS 8200 and MBS 8250 MBS 8200 is a series of compact pressure transmitters developed to withstand the pressure pulsations and vibrations known
More informationPressure transmitters for heavy duty applications Type MBS 3250
Pressure transmitters for heavy duty applications Type MBS 3250 Features Designed for use in harsh industrial environments For medium and ambient temperatures up to 125 C With integrated pulse-snubber.
More informationJUMO MIDAS S05 Pressure transmitter Type
Data Sheet 40.00 Page /8 JUMO MIDAS S05 Pressure transmitter Type 4000 Brief description The JUMO MIDAS S05 pressure transmitter is available with both relative pressure and absolute pressure measurement
More informationLevel Sensor with G1/2" Thread Hygienic
SENSORS FOR FOOD AND BIOPHARMA. Product Information NVS-141, -143, -146, -161, -163, -166, -181, -183, -186 FOOD Level Sensor with Thread Hygienic Application/intended use Limit detection of aqueous and
More informationPressure transmitters for heavy duty applications MBS 3200 and 3250
Data sheet Pressure transmitters for heavy duty applications MBS 3200 and 3250 The compact high temperature pressure transmitter MBS 3200 is designed for use in hydraulic and almost all industrial applications,
More informationLevel Sensor with M12 Thread Hygienic
SENSORS FOR FOOD AND BIOPHARMA. Product Information NVS-041, -043, -046, -061, -063, -066, -081, -083, -086 FOOD Level Sensor with M12 Thread Hygienic Application/intended use Limit detection of aqueous
More informationSUCO Product Overview
SUCO Product Overview Pressure Monitoring & an overview Mechanical Pressure Switches Electronic Pressure Sensors www.suco.de Mechanical Pressure Switches Pressure Switches with integrated connectors NO
More informationOBSOLETE. Data Sheet P1E Oxygen Service Pressure Sensor. Main Features. Typical Applications. Attributes. Description
Data Sheet P1E Oxygen Service Pressure Sensor Main Features Pressure Ranges Electrical Connection Pressure Connection 6 bar up to 400 bar (gage)* M12-4 Pole, 18mm connector, 9.4mm connector* G1/4A DIN
More informationP255 Stainless Steel Pressure Transducer
P255 Stainless Steel Pressure Transducer Description The model P255 is based on Kavlico s fieldproven ceramic capacitive technology with the latest state-of-the-art ASIC. Featuring a 316SS housing, the
More informationM5200 Industrial Pressure Transducer
SPECIFICATIONS Wide Temperature Range Compact Variety of Pressure Ports and Electrical Configurations Optional Stainless Steel Snubber CE Compliant and Weatherproof Gage, Sealed, Compound The pressure
More informationJUMO dtrans p20. Process pressure transmitter. Type Brief description. Key features. Block diagram
Data Sheet 403025 Page 1/10 JUMO dtrans p20 Process pressure transmitter Brief description The JUMO dtrans p20 pressure transmitter with HART interface combines maximum precision with easy operation. It
More informationUser Manual. Liquid Level Sensor. Unit 600 Ampress Park Lymington, Hampshire SO4 l SLW United Kingdom
7010 Liquid Level Sensor User Manual Gill Sensors & Controls Limited Unit 600 Ampress Park Lymington, Hampshire SO4 l SLW United Kingdom Tel: +44 (0) 1590 613 900 Fax +44 (0) 1590 613 901 info@gillsc.com
More informationLED Driver Linear / area fixed output industry. Driver LCI 100W 350mA 900mA TOP INDUSTRY sl TOP series
Driver LCI 100W 350mA 900mA TOP INDUSTRY sl TOP series Product description Fixed output constant current built-in LED Driver, particularly suitable for industrial applications in tough enviromments such
More informationBRIDGE-BOY Load limitation electronics with 1 or 3 set points
Change from one to two columns Data Sheet DS/BRIDGE-BOY-LCI-EN Rev. A BRIDGE-BOY Load limitation electronics with 1 or 3 set points Electronics with 1 or 3 set points designed, in combination with a load
More informationKM26z 20N; 50N; 100N, 200N, 500N, 1kN, 2kN, 5kN
KM26z 20N; 50N; 100N, 200N, 500N, 1kN, 2kN, Description The load cell KM26z is a membrane-type force sensor with small dimensions. It is suitable for measuring compressive and tensile forces. For force
More informationSPG-DIGI. Operating Instruction. Please read carefully before use!
WALTER STAUFFENBERG GMBH & CO.KG Im Ehrenfeld 4 D-58791 Werdohl Postfach 1745 D-58777 Werdohl Germany Tel.: +49 (0) 2392 / 916-0 Fax: +49 (0) 2392 / 2505 E-Mail: sales@stauff.com Internet: www.stauff.com
More information