KENCO Oil Level Controllers are designed to maintain the running oil level in the crankcase of stationary engines, compressors and mechanical

Transcription

1

2 KENCO Oil Level Controllers are designed to maintain the running oil level in the crankcase of stationary engines, compressors and mechanical lubricator boxes. The oil controller controls/monitors the amount of oil in the crankcase by a float controlled valve. COMMON FEATURES: Protect against lubrication failure Controller mechanism removable without draining oil Easy-view convex sight widow High pressure models available: psi ( bar) [HP-A] / psi ( bar) [HP-B] Direct-Mount adapters available for numerous engine and compressor models Oil inlet and outlet ports positions accommodate for various piping configurations Fire-safe valves available Controllers for synthetic oil applications available

3 KLCE KENCO Level Controller Explosion- Proof Independent switch will trip at 3/4 drop below centerline CSA & ATEX approved explosion proof design Direct wiring to switch eliminates the requirement for a terminal block Switch functionality can be tested through 3/8 vent hole

4 KHL Kenco High/Low Level Controller Independent level switch will trip at 3/4 above and 3/4 below centerline KSHL KENCO High/Low Level Switches One level switch will trip at 3/4 above and the other at 3/4 below centerline KSLL KENCO Low/Low Level Switches One level switch will trip at 5/8 and the other at 3/4 below centerline -ES option available for switch only functionality on above models

5 50-KFS FIRE SAFE VALVE 1618 LOW FLOW METER KLCE-24 DIRECT- MOUNT OIL LEVEL CONTROLLER

6 KLCM KENCO Level Controller Microswitch Independent switch will trip at 3/4 drop below centerline Switch is CSA certified Class III, Type 4 enclosure Intrinsically safe with an approved safety barrier External push-button to test switch functionality

7 VENT TUBE FOR EQUALIZATION TO BE INSTALLED BY CUSTOMER KLCM-9 OIL LEVEL CONTROLLER INDIRECTLY MOUNTED ON AN ARIEL COMPRESSOR

8 KLCP KENCO Level Controller Pneumatic Ideal for onshore / offshore locations where limited electrical power is available External push-button to test switch functionality KPS Model available for switch only functionality KENCO is the only manufacturer who offers an Oil Level Controller with a pneumatic switch.

9 KES KENCO Electric Switch CSA & ATEX approved explosion proof design Direct wiring to switch eliminates the requirement for a terminal block Independent switch will trip at 3/4 drop below centerline Model operates as a switch only and does not maintain the oil level KPS KENCO Pneumatic Switch Model Available

10 Compact design for applications with limited space Case-to-Ground electric switch for use in non-hazardous locations Switch is not submerged in oil Test-button on face of controller optional -HL High/Low Switch Option available Can be externally mounted to a lubricator box when an extra pump pocket is not available

11 OIL INLET LINE VENT LINE FOR EQUALIZATION OF INDIRECT MOUNTED CONTROLLER K512-9U OIL LEVEL CONTROLLER OIL OUTLET LINE

12 The KENCO Fire Safe Oil Control System provides two spring-loaded, thermally actuated valves. In the event of a fire, these valves automatically close, stopping the flow of oil from the crankcase of the engine and from the reserve oil supply. 50-KFS: 1/2 FNPT connections 75-KFS: 3/4 FNPT connections Prevents oil supply from feeding a fire Protection of equipment in case of fire Protection of personnel Protection to environment

13 1618 and Oil Consumption Meters Provides an accurate measurement of oil consumption of the engine (Gallons) Provides an indication of engine condition Counter is immersed in oil, assuring maximum resistance to wear from vibration Maximum inlet pressure is 50 psi (3.44 bar) No minimum flow requirement; maximum flow rate is 5 gallons per hour Model available with reed switch for electronic output

14 50-KFS FIRE SAFE VALVE 1618 LOW FLOW METER

15 Used as an oil reservoir for lubrication system Tanks & Stands can be mounted on skids to accommodate isolated location applications Available with Fire Safe Valves, which in case of fire, will stop oil from flowing from tank. Galvanized tanks and stands available for corrosive environments Available in 5, 15, 30 & 55 gallon capacities

16 For use in Lincoln, Premier and Mega lubricator boxes Controls oil level in Lubricator Case-to-ground (507-K/507-L) and S.P.D.T (507-M) models available Switch trips after 3/4 drop in oil level High pressure HP models available for inlet pressures between 5-60 psi ( bar)

17 NFS NO FLOW SAFETY SWITCH LUBRICATOR BOX LUBRICATION DIVIDER BLOCK

18 The KENCO No-Flow Switch mounts in the line between the lubricator and the cylinder. Lubrication oil flow is through the switch in a Pump-to-Point Lubrication System. Fail-Safe wear pattern. Shutdown time adjustable over a wide range Explosion-proof models available Overpressure rupture assembly optional Low flow-rate light-spring option available Switch contact rating - 2A at 30 VAC / DC

19 LUBRICATION DIVIDER BLOCK PROXIMITY SWITCH

20 Proximity Switches provide a switch signal used to detect the absence of flow in a continuously operating compressor lubrication system by monitoring cyclic movement of the divider valve piston. Switch is CSA approved for Class I, Groups A,B,C,D; Class II, Groups E,F,G: Class III, Type 4 Models that fit Modular Lube, Trabon, and Dropsa divider blocks available

21 REFLEX FLAT GLASS LEVEL GAUGE KEFS ELECTRIC FLOAT SWITCH PNEUMATIC FLOAT SWITCH KDV DUMP VALVE

22 The KENCO Model KEFS uses a float to determine the presence or absence of liquid in a vessel at the process connection. All wetted parts including the switch body are machined form stainless steel Magnetic switch operates through a solid steel barrier, so that fluid cannot leak into the switch housing 2000 psi( bar) maximum operating pressure rating Minimum specific gravity of 0.53 Switch terminal block simplifies wiring installation

23 The KENCO No-Freeze Dump Valve is a pneumatically controlled valve designed for fluid level control in pressure vessels. Operating pressures up to 2000 psi( bar) Polyurethane trim seal limits possibility of fluid cutting during operation Union nut allows valve to be removed from service without removing valve body from pressure vessel Pressure warning port will bleed liquid and or gas from weep hole Larger shaft diameter for improved durability Larger trim size on 1 model for improved fluid flow from valve

24 106 and 207 Pneumatic Float Switches Automatic water make-up for cooling water expansion tanks Low or high level switch for monitoring levels in tanks Standard Aluminum and optional Stainless Steel switch models available Maximum pressure rating of 100 psi(6.8 bar)

25 SURGE TANK WATER FILLER CAP ASSEMBLIES, LEVEL GAUGE AND FLOAT SWITCH INSTALLED ON A SURGE TANK

26 Ideal for surge tank applications Models 390 and available with 1 connections Model 1794 available with 2 connection 7 psi and 15 psi cap pressure ratings