MODEL N OWNER S MANUAL. Keep this Product ID Number and use when contacting Customer Service:

Transcription

1 MODEL N OWNER S MANUAL Keep this Product ID Number and use when contacting Customer Service:

2 REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefits to registering your Lifetime product. With our new online product registration form, it s fast and easy! Register with us at and enjoy these great benefi ts: as NEW product notifications and special closeout promotions! receipt to verify your product purchase date before warranty service will be provided. Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that Lifetime will not sell or provide your personal data to other third parties, or allow them to use your personal data for their own purposes. We invite you to read our privacy policy at REGISTER today! Save this owner s manual for future reference and in the event that the manufacturer has to be contacted. **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, DO NOT CONTACT THE STORE! CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time) **Call us or visit our Web site for Saturday hours** Lifetime Products, Inc. **For customers outside the U.S. or Canada, please contact the store for assistance.** 2 12/30/2011

3 SAFETY INSTRUCTIONS DAMAGE AND WILL VOID WARRANTY. To ensure safety, do not attempt to assemble this product without reading and materials for parts and/or additional instruction material. identify and inventory all parts and hardware using the parts and hardware lists and identifi ers in this document. Proper and complete assembly, use and supervision and/or operated properly. Failure to comply with any of the warnings in this result in property damage. Please heed all warnings and cautions. sections to separate during play or transport. Most injuries are caused by misuse and/or not following instructions. Use caution when using this product. BEFORE BEGINNING ASSEMBLY Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. Identify and inventory all parts and hardware using the parts and hardware lists and identifi ers in this document. buildup from inside the holes. Do not scrape away all of the 3

4 TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY 1/2 Wrench 7/16 Wrench 9/16 Wrench (2) (2) (2) 3/4 Wrench Phillips Screwdriver Pliers (2) Electric Drill (1) Rubber Mallet (1) Scrap Wood (1) Sand (1) (1) Water Hose (375 lb) 3/16 Allen Wrench (2, included) (1) (1) *Two adults required to complete assembly* Only adults should set up the product. Do not allow children in the setup area until assembly is complete. 4

5 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE This area is usually located in the bottom, left-hand corner of a step and indicates that special attention is needed to perform a particular part of a step.! Note: These areas are usually located in the bottom, right-hand corner of a step and indicate that damage to the product or serious injury may occur if the caution or warning is not heeded. CAUTION WARNING 5

6 PARTS LIST ID Item Description Qty Top Pole 1 Middle Pole 1 1 AJK 1 AJJ 1 AJI 1 Pole Cap 1 Rim 1 Net 1 Rim Cord 1 Plastic Guard 1 AKF Gas Spring 1 AKG Gas Spring Cover 1 AJD 1/2 1 AJM 1 AMU Wheel 2 AJN 1 AKC Corner Frame Pad 2 AJQ Center Frame Pad 1 1 AKI Handle 1 AMN Trigger 1 2 AKP 1 AMT 1 HARDWARE LIST ID Item Description Qty BCO Pole Assembly Hardware ADS 2 2 AAF 3/8 Washer CIH 2 BCQ Pole to Base Assembly Hardware 1 AAE 2 AAO 2 1 6

7 HARDWARE LIST ID Item Description Qty BCQ Pole to Base Assembly Hardware, Continued 5/16 Washer 4 3/16 Allen Wrench 2 BCS Backboard & Rim Assembly Hardware AAS ACS 2 2 AAJ 2 5/16 Washer 2 7/16 Rubber Washer AAV 5/16 Jam Nut 2 AAF 3/8 Washer 2 AFA 1 APT 1 APU Silver Spring Cover 1 APV Spring Retainer Plate 1 APW Compression Spring 2 BCR Backboard to Pole Assembly Hardware AAD BCT Handle Assembly Hardware AAH Cotter Pin 1 AAI Clevis Pin 1 1 AAO AQE Release Pin 1 2 AAW 1 AKH 1 AAD 1 1 BCU Frame Pad Assembly Hardware (HH00700) ADP 10 7

8 Parts shown at 10% of Actual Size PARTS IDENTIFIER ALH Top Pole 43 3/8 Middle Pole 43 3/8 ALE 27 5/8 AKI Handle 25 7/8 AKB 21 1/8 AKC ALI 38 ALS 31 Corner Frame Pad Center Frame Pad Gas Spring AKG Gas Spring Cover /4 AMN Trigger

9 Parts shown at 10% of Actual Size PARTS IDENTIFIER Rim AKZ Net ALA Rim Cord Parts shown at 5% of Actual Size 9

10 Parts shown at 25% of Actual Size PARTS IDENTIFIER ALM Pole Cap AMU Wheel ALL ALD Plastic Guard AKP 10

11 POLE ASSEMBLY HARDWARE Hardware shown at Actual Size HARDWARE IDENTIFIER ABE ABR ABB ABZ 3/8 Washer ADS CIH POLE TO BASE ASSEMBLY HARDWARE Hardware shown at Actual Size BZP AAO Nut AAE ABD 5/16 Washer BTS CCL 3/16 Allen Wrench 11

12 HARDWARE IDENTIFIER BACKBOARD TO RIM ASSEMBLY HARDWARE Hardware shown at Actual Size ABG ABC AAS ABS ACS ABD 5/16 Washer 7/16 Rubber Washer 3/8 Washer ABK Flange Nut AAV 5/16 Jam Nut AAB Hardware shown at 25% of Actual Size APV Spring Retainer Plate APW Compression Spring 12

13 HARDWARE IDENTIFIER BACKBOARD TO RIM ASSEMBLY HARDWARE (CONTINUED) Hardware shown at 25% of Actual Size APT APU Silver Spring Cover BACKBOARD TO POLE ASSEMBLY HARDWARE Hardware shown at Actual Size 7 1/16 AAD (Not actual length) ABN ABL HANDLE ASSEMBLY HARDWARE Hardware shown at Actual Size 6 1/2 (Not actual length) ABA 6 1/2 ABB Nut AAO Nut (Not actual length) AAW 13

14 HARDWARE IDENTIFIER HANDLE ASSEMBLY HARDWARE (CONTINUED) Hardware shown at Actual Size 7 1/16 (Not actual length) AAD AAH Cotter Pin AQE Release Pin AAI Clevis Pin ABT ABM Note: The Clevis Pin (AAI) and the Cotter Pin (AAH) will not be used in this assembly. Hardware shown at Actual Size ADP Note: Only eight of the 10 Screws will be used. 14

15 1 POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ABE ABR ABZ ADS CIH 3/8 Washer ABB 15

16 1 POLE ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size ALH Top Pole 43 3/8 Middle Pole 43 3/8 ALE 27 5/8 Part shown at 25% of Actual Size ALL TOOLS REQUIRED 9/16 Wrench Phillips Screwdriver Electric Drill 16 Scrap Wood

17 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ABE ABR 1.1 Insert the 3/8 x 4 Hex Bolts (ABE) with the into the Top Pole (ALH) as shown. Then slide the 1/2 x 3.41 Spacers (ABR) onto the ABE ABR Small holes Large holes ALH 17

18 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9/16" ABB 1.2 Place the Pole Bracket (ALL) onto the 3/8 x 4 Hex Bolts (ABE), and attach it to the Top Pole (ALH) with the hardware shown. ABE ABB ALL ALH 18

19 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADS CIH 1.3 Align the hole in the Top Pole (ALH) with the slot in the and slide the Top Pole over the Middle Pole. Insert a 1/4 x 3/4 Screw (ADS) through the small hole in the Top Pole and into the slot in the Middle Pole as shown. ALH ALH CIH ADS Warning Sticker! Note: The 1/4 x 3/4 Screw should be fl ush with the Pole, but will spin freely once installed. Do not jam the Poles together until instructed. 19

20 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADS CIH 1.4 Align the hole in the with the slot in the Bottom Pole (ALE) and 1/4 x 3/4 Screw (ADS) Pole as shown. ALH CIH ADS ALE ALE! Note: The 1/4 x 3/4 Screw should be fl ush with the Pole, but will spin freely once installed. Do not jam the Poles together until instructed. 20

21 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1.5 ATTENTION: THIS STEP CANNOT BE REVERSED! times on a piece of scrap wood or cardboard. This must be done even if the Poles cover the slots before seating has occurred. If the do not completely cover the slots on the after seating, DO NOT COMPLETE ASSEMBLY. Call our Customer Service Department. ALE ALH WARNING The Poles must be seated together! Even if the Poles cover the slots before seating, they must be struck on a hard surface fi ve to six times! Failure to seat the Poles correctly could allow the Poles to separate during use, which could lead to serious personal injuries or property damage.! Note: Do not hit your feet with the Pole sections, as serious injury could occur. 21

22 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ABZ 1.6 After the Poles have been seated, insert two #14 x 1 Self-Tapping Screws (ABZ) ALH ABZ ABZ ALE! Note: Chuck the #14 x 1 Self-Tapping Screw directly into an Electric Drill for easy installation, or use a 3/8 Hex Driver. 22

23 2 POLE TO BASE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size AAE AAO BTS ABD 5/16 Washer BZP Part shown at 5% of Actual Size PARTS REQUIRED Parts shown at 25% of Actual Size AMU Wheel Parts shown at 10% of Actual Size ALI 21 3/4 38 TOOLS REQUIRED 1/2" Wrench Rubber Mallet 23 3/16 Allen Wrench

24 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2.1 Screw the onto the as shown. Rubber Gasket! 2.2 Note: Make sure the Rubber Gasket is inside the Base Cap. Slide the through one of the Wheels (AMU) and into the as shown. Then have one adult position the Bottom Pole (ALE) ALE AMU AMU! Note: It may be necessary to use a Rubber Mallet to tap the Axle into place. 24

25 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2" 3/16" BZP AAE AAO ABD BTS 2.3 Attach the fl attened end of the Pole Brace (ALI) to the with the hardware shown. Only fi nger tighten the hardware. ALI! 2.4 AAE ABD ABD AAO Note: Repeat this step to install the other Pole Brace to the other side of the Base. Attach the Pole Braces (ALI) to the Bottom Pole (ALE) with the hardware BTS ALI ALI BZP ALE! Note: Tip the system backward so the Pole rests on the ground. Do not stand the system up until it is filled with either sand or water later in the assembly. 25

26 3 BACKBOARD TO RIM ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size AAS ACS ABG AAV 5/16 Jam Nut ABC ABS ABK ABD 5/16 Washer 7/16 Rubber Washer 3/8 Washer AAB Hardware shown at 25% of Actual Size APV Spring Retainer Plate APW Compression Spring APU Silver Spring Cover 26 APT

27 3 BACKBOARD TO RIM ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size Rim Part shown at 5% of Actual Size Part shown at 25% of Actual Size ALD Plastic Guard TOOLS REQUIRED Pliers 1/2 Wrench 7/16 Wrench 27

28 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16 AAS (Not to scale) ABS AAB 3.1 Slide the through the as shown. Notch 3.2 1/4 x 2 3/4 Hex Bolts (AAS), two 1/2 x 2 5/16 Galvanized Spacers (ABS), and two 1/4 Centerlock Nuts (AAB). AAS ABS AAS AAB! Note: Tighten the hardware securely now. 28 AAB

29 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 ABG ABD 3.3 Insert two 5/16 x 2 1/2 Tap Bolts (ABG) with the 5/16 Washers (ABD) and the Rim as shown, and secure the hardware with two. ABG ABD ABG ABG! Note: Make sure that the 5/16 x 2 1/2 Tap Bolts are positioned on the outside edge of the holes as shown.! Incorrect Note: Do not overtighten the hardware so that the 7/16 Rubber Washers bulge outward as shown. 29 Correct

30 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 ACS AAV ABK 3.4 Insert the through the upper part of the opening on the as shown. 3.5 Connect the and Plastic Guard (ALD) to the with the hardware shown. Thread the all the way down on the..38 x 1 Steel Spacers (ACS) onto the 5/16 x 2 1/2 Tap Bolts (ABG), and secure the 5/16 ABK ABK ACS ABG AAV AAV ALD Underside View 30

31 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE APV APW ABK APU 1/2 (Not to scale) APT (Not to scale) (Not to scale) (Not to scale) 3.6 Slide the Silver Spring Cover (APU) over the as shown, and fit the tabs of the Silver Spring Cover into the slots in the. Then slide the Compression Springs (APW) Spring Retainer Plate (APV) over the Compression Springs. Place the Black Spring Cover (APT) over the Spring Retainer Plate, and secure all of the ABK APT APV APW APU! Note: DO NOT COMPLETELY TIGHTEN THE 5/16 NYLOCK FLANGE NUTS (ABK) IN THIS STEP! Only tighten the Nuts until the Rim does not wobble. Tightening the Nuts will adjust the Rim tension. 31

32 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 ABC ABK 3.7 Slide a 5/16 x 1 1/4 Carriage Bolt (ABC) into the crimped slot in each ABC ABC 3.8 the 5/16 x 1 1/4 Carriage Bolts (ABC) ABC ABK ABK ABC! Note: Tighten the 5/16 Nylock Flange Nuts (ABK) until they are flush with the ends of the Bolts. 32

33 4 BACKBOARD TO POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ABL 7 1/16 ABN (Not actual length) AAD Parts shown at 10% of Actual Size PARTS REQUIRED 21 1/8 AKC 25 7/8 AKB Part shown at 25% of Actual Size ALM Pole Cap TOOLS REQUIRED 3/4 Wrench Rubber Mallet 33

34 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7 1/16 3/4 AAD (Not actual length) ABL 4.1 Secure the Short Extension Arms (AKC) location shown with the hardware indicated. AKC AKC ABL ABL AAD AKC! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 34

35 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7 1/16 3/4 AAD (Not actual length) ABL 4.2 Secure the ends of the Long Extension Arms (AKB) that only have one hardware indicated. AKB AKB ABL ABL AAD AKB! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 35

36 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 7 1/16 ABN AAD (Not actual length) 4.3 CAUTION: HAVE ONE ADULT HOLD THE BACKBOARD IN PLACE UNTIL ASSEMBLY HAS BEEN COMPLETED! Rim on cardboard to prevent scratching. Then secure the Long Extension Arms (AKB) to the Top Pole (ALH) with the hardware shown. Do not tighten the hardware in this step until instructed to later in the assembly. AKB AKB ABN ABN AAD ALH 36

37 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 7 1/16 ABN AAD (Not actual length) 4.4 Secure the Short Extension Arms (AKC) to the Top Pole (ALH) with the hardware shown. Do not tighten the hardware in this step until instructed to later in the assembly. AKC ABN AKC ABN AAD ALH 37

38 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 4.5 Insert the Pole Cap (ALM) into the end of the Top Pole (ALH). ALM ALH 38

39 5 HANDLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size 7 1/16 AQE Release Pin AAI Clevis Pin (Not actual length) AAD 6 1/2 (Not actual length) ABA 6 1/2 AAH Cotter Pin ABB Nut AAO Nut (Not actual length) AAW ABT ABM Note: The Clevis Pin (AAI) and the Cotter Pin (AAH) will not be used in this assembly. 39

40 5 HANDLE ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size ALS 31 AKI Handle Gas Spring Part shown at 25% of Actual Size AKG Gas Spring Cover AMN Trigger AKP TOOLS REQUIRED 9/16" Wrench 3/4" Wrench 40 1/2" Wrench

41 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 AAO 5.1 Slide the Gas Spring Cover (AKG) onto the as shown. AKG 5.2 Slide the cutout portion of the Gas Spring Cover (AKG) over the Pole Bracket (ALL) as shown. Then align the holes in the Gas Spring Cover and the Gas AKG ALL AAO! Note: Tighten the 5/16 Nylock Nut (AAO) until it is flush with the end of the Bolt. 41

42 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 1/2 9/16 ABA (Not actual length) ABB AQE 5.3 Position the Trigger (AMN) inside of the Handle (AKI) as shown, and secure the Trigger to the Handle with the hardware shown. AMN ABB AKI ABA! 5.4 Note: Tighten the 3/8 Centerlock Nut (ABB) until it is flush with the end of the Bolt. Insert the Release Pin (AQE) through the slots on the, and position the Handle (AKI) under the Gas Spring so that the Release Pin rests in the channels of the Trigger (AMN). AQE AMN AKI 42

43 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 6 1/2 AAW (Not actual length) 5.5 Position the Rear Lifter Arms (ALS) between the Handle (AKI) and Trigger (AMN) as shown, and secure with the hardware shown. ALS AAW ALS AMN AKI! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 43

44 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9/16 6 1/2 ABA (Not actual length) ABB ABM 5.6 Secure the Handle (AKI) to the with the hardware shown. 3/8 x 1/2 Spacers (ABM) between the Handle Assembly and the Middle Pole as shown. ABA ABB ABM ABM AKI 44

45 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 AAD 7 1/16 (Not actual length) ABT 5.7 Connect the Rear Lifter Arms (ALS) to the inside of the Long Extension Arms (AKB) with the hardware shown. Place a.62 x 3.20 Spacer (ABT) step and in steps 4.3 and 4.4 securely now. AAD AKB ABT ALS AKB ALS WARNING The Handle mechanism is designed to lift Do not hang anything from the Handle, Rim, the system and void the warranty.! Note: The Rear Lifter Arms must be on the inside of the Long Extension Arms. 45

46 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5.8 Apply grease from the Grease Packet (AKH) on to the Release Pin (AQE). AQE 5.9 Height Sticker (AKP) to the Gas Spring Cover (AKG) as shown. AKG AKP 46

47 6 HARDWARE REQUIRED Hardware shown at Actual Size ADP Note: Only eight of the 10 Screws will be used. Parts shown at 10% of Actual Size PARTS REQUIRED ALA Rim Cord Corner Frame Guard AKZ Net Center Frame Guard TOOLS REQUIRED Sand (375 lb) Water Hose 47 Electric Drill

48 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADP 6.1 Remove the plastic fi lm from the, and attach the ADP ADP ADP 6.2 ADP Attach the to the in the locations shown with the hardware indicated. ADP ADP 48

49 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE (375 lb) Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. 6.3 (375 lb of sand required) a. Fill the with sand. b. Screw the onto the fi ll hole. WARNING For safety reasons, we recommend that sand be used instead of water to fill the Base. If a leak develops, water could run out unnoticed, allowing the system to fall over, resulting in serious personal injuries, or property damage. If using Water, check the Base carefully for leaks. If a leak is found, lay the system down on the ground and call Customer Service. Do not use, stand up, or play on a leaking system. 49

50 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. 6.3 a. Add cold water up to the fi ll hole, leaving two inches of space at b. Add one tablespoon of chlorine bleach to the water to prevent algae formation. c. Screw the onto the fi ll hole. d. Using two adults, stand the up on a smooth surface. 50

51 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6.4 Attach the Net (AKZ). Then thread the Rim Cord (ALA) ALA AKZ! Note: If a replacement Net is needed, please call our Customer Service Department. Our Nets are shorter than average to reduce the risk of entanglement. 51

52 OPERATION OF HEIGHT ADJUSTMENT SYSTEM To Adjust the Height of the Hoop: MOVING THE SYSTEM WARNING: The system must only be moved by people capable of handling its weight. Children should not be allowed to move the system. b. Stand in front of the system and pull on the Pole until the unit is balanced on its Wheels. CAUTION: The system must only be moved on its Wheels. Sliding the system tipping over. POLE CARE AND SYSTEM MAINTENANCE tears that could let water in the Pole. Contact our Customer Service Department for replacement parts. are present, do the following: 1. Use an emery cloth to completely remove any rust or chipped paint. 2. Clean the area with a damp cloth and allow it to dry. 3. Apply two coats of a rust preventative, high gloss enamel paint to the area. Allow the paint to dry between coats. 52

53 NOTES 53

54 ENHANCE YOUR LIFETIME PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS: To purchase accessories or other Lifetime Products, visit us at: Or call:

55 WARNING PROPERTY DAMAGE. penetrated any steel part, replace that part immediately. operation of the system. wear, instability, and signs of corrosion and repair before use. the rim as soon as safely possible. system in an area protected from the wind or in an area away from property that may be damaged if the system falls, and from overhead power lines. guard during play. void the warranty. unit standing in an upright position without first filling the base with weight or moving parts. entangle in net. corrosion and/or deterioration. ADVERTENCIA SI NO SE OBEDECEN ESTAS ADVERTENCIAS PUEDEN PRODUCIRSE GRAVES LESIONES Y/O DAÑOS A LA PROPIEDAD. segura. AVERTISSEMENT SURES GRAVES ET/OU DES DOMMAGES À L ÉQUIPEMENT. con seguridad. producirse lesiones graves si los dientes o la cara entran en contacto con el causar graves lesiones personales. regule la altura o desplace el sistema. de energía. para elevar solamente el peso del tablero con el aro. No cuelgue nada de la possible. graves blessures si ses dents ou son visage entrent en contact avec le panneau, blessures. pièce en question. 10/12/

56 WARRANTY INFORMATION UNAVAILABLE OR OBSOLETE. is defi ned as imperfections that impair the use of the product. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installation, nature or any other event beyond the control of the manufacturer. Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from covered under this warranty. 3. This warranty does not cover scratching or scuffi ng of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use or hanging from the net or rim will void this warranty. merchandise is sold on this condition, and no representative of the company may waive or change this policy. any liability for such use. Institutional or commercial use will void the warranty. Products, Inc., nor any representative assumes any other liability in connection with this product. This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT. **Call or visit our Web site for Saturday hours** Please include your dated sales receipt and photographs of damaged parts. To register the product, visit our Web site at