1 DIAPHRAGM PUMP 1:1 RATIO (METALLIC)

Transcription

1 OPERTOR S MNUL INCLUDING: OPERTION, INSTLLTION ND MINTENNCE RELESED: REVISED: (REV: M) 1 DIPHRGM PUMP 1:1 RTIO (METLLIC) RED THIS MNUL CREFULLY BEFORE INSTLLING, OPERTING OR SERVICING THIS EQUIPMENT. It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference. SERVICE KITS Refer to Model Description Chart to match the pump material options XXX for Fluid Section Repair with seats (see page 4) XX for Fluid Section Repair without seats (see page 4). NOTE: This kit also contains several air motor seals which will need to be replaced for ir Section Repair (see page 6). PUMP DT Models See Model Description Chart for -XXX. Pump Type.... Non-Metallic ir Operated Double Diaphragm Material See Model Description Chart. Weight PE10P-KS-XXX-0S lbs (11.52 kgs) PE10P-PS-XXX-0S lbs (8.58 kgs) PE10P-BKS-XXX-0S lbs (11.52 kgs) PE10P-BPS-XXX-0S lbs (8.58 kgs) PE10P-FKS-XXX-0S lbs (12.12 kgs) PE10P-FPS-XXX-0S lbs (8.82 kgs) PE10P-YKS-XXX-0S lbs (11.93 kgs) PE10P-YPS-XXX-0S lbs (8.69 kgs) Maximum ir Inlet Pressure psig (8.3 bar) Maximum Material Inlet Pressure psig (0.69 bar) Maximum Outlet Pressure psig (8.3 bar) Maximum Flow Rate (Flooded inlet) gpm (200.6 lpm) Displacement / 100 psig gal. (0.86 lit.) Maximum Particle Size.... 1/8 dia. (3.2 mm) Maximum Temperature Limits (Diaphragm/ Ball/ Seat material) E.P.R./ EPDM to F (-51 0 to C) Hytrel to F (-29 0 to 82 0 C) Nitrile to F (-12 0 to 82 0 C) Polypropylene to F (2 0 to 79 0 C) PVDF (Kynar ) to F (-12 0 to 93 0 C) Santoprene to F (-40 0 to C) PTFE to F (4 0 to C) Viton to F (-40 0 to C) Dimensional Data... see page 8 Mounting Dimension x (127.8 mm x mm) Noise 70 psig, 60 cpm db() The pump sound pressure levels published here have been updated to an Equivalent Continuous Sound Level (L eq ) to meet the intent of NSI S , CGI-PNEUROP S5.1 using four microphone locations. NOTICE: ll possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability. INGERSOLL RND COMPNY LTD 209 NORTH MIN STREET BRYN, OHIO (800) FX (800) CCN arozone.com PE10P-XS-XXX-0S PE10P-BXS-XXX-0S MODEL DESCRIPTION CHRT CENTER SECTION MTERIL P - Polypropylene FLUID CONNECTION / LOCTION /2 NPTF - 1 B - Rp 1-11 BS F - 1 NSI / DN Flange / End Y - 1 NSI / DN Flange / Center FLUID CPS ND MNIFOLD MTERIL K - PVDF (Kynar) P - Polypropylene HRDWRE MTERIL S - Stainless Steel SET MTERIL H - Hard 440 Stainless Steel K - PVDF (Kynar) P - Polypropylene S Stainless Steel BLL MTERIL - Santoprene C - Hytrel G- Nitrile PE10P-FXS-XXX-0S T - PTFE V - Viton DIPHRGM MTERIL - Santoprene L - Long Life PTFE V - Viton C - Hytrel M - Medical Grade Santoprene G- Nitrile T - PTFE / Santoprene PE10P-YXS-XXX-0S Figure 1 PE10 P - X X S - X X X - 0S FLUID SECTION SERVICE KIT SELECTION PE10P- XXS - X X X - 0S EXMPLE:MODEL # PE10P-FPS-P-0S X X FLUID SECTION SERVICE KIT # Ball Diaphragm

2 OPERTING ND SFETY PRECUTIONS RED, UNDERSTND, ND FOLLOW THIS INFORMTION TO VOID INJURY ND PROPERTY DMGE. EXCESSIVE IR PRESSURE STTIC SPRK HZRDOUS MTERILS HZRDOUS PRESSURE WRNING EXCESSIVE IR PRESSURE. Can cause personal injury, pump damage or property damage. S Donotexceedthemaximuminletairpressureasstatedonthe pump model plate. S Be sure material hoses and other components are able to withstand fluid pressures developed by this pump. Check all hoses for damage or wear. Be certain dispensing device is clean and in proper working condition. WRNING STTIC SPRK. Can cause explosion resulting in severe injury or death. Ground pump and pumping system. S Sparks can ignite flammable material and vapors. S The pumping system and object being sprayed must be grounded when it is pumping, flushing, recirculating or spraying flammable materials such as paints, solvents, lacquers, etc. or used in a location where surrounding atmosphere is conducive to spontaneous combustion. Ground the dispensing valve or device, containers, hoses and any object to which material is being pumped. S Secure pump, connections and all contact points to avoid vibration and generation of contact or static spark. S Consult local building codes and electrical codes for specific grounding requirements. S fter grounding, periodically verify continuity of electrical path to ground. Test with an ohmmeter from each component(e.g., hoses, pump, clamps, container, spray gun, etc.) to ground to insure continuity. Ohmmeter should show 0.1 ohms or less. S Submerse the outlet hose end, dispensing valve or device in the material being dispensed if possible.(void free streaming of material being dispensed.) S Use hoses incorporating a static wire. S Use proper ventilation. S Keep inflammables away from heat, open flames and sparks. S Keep containers closed when not in use. WRNING Pump exhaust may contain contaminants. Can cause severe injury. Pipe exhaust away from work area and personnel. S Intheeventofadiaphragmrupture,materialcanbeforcedout of the air exhaust muffler. S Pipe the exhaust to a safe remote location when pumping hazardous or inflammable materials. S Useagrounded3/8 minimumi.d.hosebetweenthepumpand the muffler. WRNING HZRDOUS PRESSURE. Can result in serious injury or property damage. Do not service or clean pump, hoses or dispensing valve while the system is pressurized. S Disconnect air supply line and relieve pressure from the systembyopeningdispensingvalveordeviceand/orcarefully and slowly loosening and removing outlet hose or piping from pump. WRNING HZRDOUS MTERILS. Can cause serious injuryorpropertydamage.donotattempttoreturnapumptothe factory or service center that contains hazardous material. Safe handling practices must comply with local and national laws and safety code requirements. S Obtain Material Safety Data Sheets on all materials from the supplier for proper handling instructions. WRNING EXPLOSION HZRD. Models containing aluminum wetted parts cannot be used with III.-Trichloroethane, Methylene Chloride or other Halogenated Hydrocarbon solvents which may react and explode. S Check pump motor section, fluid caps, manifolds and all wetted parts to assure compatibility before using with solvents of this type. WRNING MISPPLICTION HZRD. Do not use models containing aluminum wetted parts with food products for human consumption. Plated parts can contain trace amounts of lead. CUTION Verify the chemical compatibility of the pump wetted parts and the substance being pumped, flushed or recirculated. Chemical compatibility may change with temperature and concentration of the chemical(s) within the substances being pumped, flushed or circulated. For specific fluid compatibility, consult the chemical manufacturer. CUTION Maximum temperatures are based on mechanical stress only. Certain chemicals will significantly reduce maximum safe operating temperature. Consult the chemical manufacturer for chemical compatibility and temperature limits.refertopumpdtonpage1ofthismanual. CUTION Be certain all operators of this equipment have been trained for safe working practices, understand it s limitations, and wear safety goggles/ equipment when required. CUTION Do not use the pump for the structural support of the piping system. Be certain the system components are properly supported to prevent stress on the pump parts. S Suction and discharge connections should be flexible connections(such as hose), not rigid piped, and should be compatible with the substance being pumped. CUTION Prevent unnecessary damage to the pump. Do notallowpumptooperatewhenoutofmaterialforlongperiods of time. S Disconnect air line from pump when system sits idle for long periods of time. CUTION Use only genuine RO replacement parts to assure compatible pressure rating and longest service life. NOTICE RE-TORQUE LL FSTENERS BEFORE OPER- TION. Creep of housing and gasket materials may cause fasteners to loosen. Re-torque all fasteners to insure against fluid or air leakage WRNING CUTION NOTICE = Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. = Hazards or unsafe practices which could result in minor personal injury, product or property damage. = Important installation, operation or maintenance information. Page 2of8

3 GENERL DESCRIPTION TheROdiaphragmpumpoffershighvolumedeliveryevenatlowair pressure and a broad range of material compatibility options available. Refer to the model and option chart. RO pumps feature stall resistant design, modular air motor/ fluid sections. ir operated double diaphragm pumps utilize a pressure differential in the air chambers to alternately create suction and positive fluid pressure in the fluid chambers, ball checks insure a positive flow of fluid. Pumpcyclingwillbeginasairpressureisappliedanditwillcontinueto pumpandkeepupwiththedemand.itwillbuildandmaintainlinepressure and will stop cycling once maximum line pressure is reached(dispensing device closed) and will resume pumping as needed. IR ND LUBE REQUIREMENTS WRNING EXCESSIVE IR PRESSURE. Can cause pump damage, personal injury or property damage. S filter capable of filtering out particles larger than 50 microns should beusedontheairsupply.thereisnolubricationrequiredotherthan the O ring lubricant which is applied during assembly or repair. S Iflubricatedairispresent,makesurethatitiscompatiblewiththe O ringsandsealsintheairmotorsectionofthepump. INSTLLTION S Verify correct model/ configuration prior to installation. S Retorque all external fasteners per specifications prior to start up. S Pumps are tested in water at assembly. Flush pump with compatible fluid prior to installation. S When the diaphragm pump is used in a forced-feed(flooded inlet) situation, it is recommended that a Check Valve be installed at the air inlet. S Material supply tubing should be at least the same diameter as the pump inlet manifold connection. S Material supply hose must be reinforced, non-collapsible type compatible with the material being pumped. S Pipingmustbeadequatelysupported.Donotusethepumptosupport the piping. S Use flexible connections (such as hose) at the suction and discharge. These connections should not be rigid piped and must be compatible with the material being pumped. S Secure the diaphragm pump legs to a suitable surface(level and flat) to insure against damage by vibration. S Pumpsthatneedtobesubmersedmusthavebothwetandnon-wet components compatible with the material being pumped. S Submersed pumps must have exhaust pipe above liquid level. Exhaust hose must be conductive and grounded. S Flooded suction inlet pressure must not exceed 10 p.s.i.g. (0.69 bar). OPERTING INSTRUCTIONS S lways flush the pump with a solvent compatible with the material being pumped if the material being pumped is subject to setting up whennotinuseforaperiodoftime. S Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew hours. PRTS ND SERVICE KITS Refertothepartviewsanddescriptionsasprovidedonpages4through 7 for parts identification and Service Kit information. S Certain RO Smart Parts are indicated which should be available for fast repair and reduction of down time. S Service kits are divided to service two separate diaphragm pump functions: 1. IR SECTION, 2. FLUID SECTION. The FLUID SEC- TION is divided further to match typical part MTERIL OPTIONS. MINTENNCE S Provide a clean work surface to protect sensitive internal moving parts from contamination from dirt and foreign matter during service disassembly and reassembly. S Keep good records of service activity and include pump in preventive maintenance program. S Before disassembling, empty captured material in the outlet manifoldbyturningthepumpupsidedowntodrainmaterialfromthe pump. FLUID SECTION DISSSEMBLY 1. Remove(60) inlet manifold and(61) outlet manifold. 2. Remove(22)balls,(19and33) O ringsand(21)seats. 3. Remove(15) fluid caps. NOTE: Only PTFE diaphragm models use a primary diaphragm(7) and abackupdiaphragm(8).refertotheauxiliaryviewinthefluidsection illustration. 4. Removethe(6)diaphragmwasher,(7)or(7/8)diaphragms,and(5) backup washer. NOTE:Donotscratchormarthesurfaceof(1)diaphragmrod. FLUID SECTION RESSEMBLY S Reassemble in reverse order. Refer to the torque requirements on page 5. S Clean and inspect all parts. Replace worn or damaged parts with new parts as required. S Lubricate (1) diaphragm rod and (144) U cup with LubriplateR FML-2 grease(94276 grease packet is included in service kit). S For models with PTFE diaphragms: Item(8) Santoprene diaphragm isinstalledwiththesidemarked IRSIDE towardsthepumpcenter body. Install the PTFE diaphragm (7) with the side marked FLUID SIDE towards the(15) fluid cap. S Re-check torque settings after pump has been re-started and run a while. S VitonR and HytrelR are trademarks of the DuPont Company S KynarR is a registered trademark of Penwalt Corp. S LoctiteR is a registered trademark of Henkel Loctite Corporation S S SantopreneR is a registered trademark of Monsanto Company, licensed to dvanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division(Fiske Brothers) S Page 3of8

4 PRTS LIST / FLUID SECTION Fluid Section Service Kits ( XXX or XX): For Fluid Kits With Seats : XXX Fluid Section Service Kits include: Seats (see SET Option, refer to -XXX in chart below), Balls (see BLL Option, refer to -XXX in chart below), Diaphragms (see DIPHRGM Option, refer to -XXX in chart below), and items 19, 33, 70, 144, 175 and 180 (listed below) plus Lubriplate FML-2 grease (page 6). For Fluid Kits Without Seats: XX Fluid Section Service Kits include: Balls (see BLL Option, refer to -XX in chart below), Diaphragms (see DI- PHRGM Option, refer to -XX in chart below), and items 19, 33, 70, 144, 175 and 180 (listed below) plus Lubriplate FML-2 grease (page 6). SET OPTIONS PE10P-XXS-XXX-0S BLL OPTIONS PE10P-XXS-XXX-0S (1-1/4 dia.) -XXX Seat Qty [Mtl] -XXX Ball Qty [Mtl] -XXX Ball Qty [Mtl] -HXX (4) [SH] -XX (4) [SP] -XSX (4) [SS] -KXX (4) [K] -XCX C (4) [H] -XTX (4) [T] -PXX (4) [P] -XGX (4) [B] -XVX (4) [V] -SXX (4) [SS] -XMX M (4) [MSp] MTERIL CODE [] = luminum [B] = Nitrile [C] = Carbon Steel [Co] = Copper [CI] = Cast Iron [E] = E.P.R. [H] = Hytrel [Ha] = Hastelloy - C [K] = Kynar PVDF [L] = Long Life PTFE [MSp] = Medical grade Santoprene [SH] = Hard Stainless Steel [Sp] = Santoprene [SS] = Stainless Steel [T] = PTFE [V] = Viton DIPHRGM OPTIONS PE10P-XXS-XXX-0S SERVICE KIT SERVICE KIT WITH SET WITHOUT SET O Ring O Ring -XXX= (Seat) -XX = (Ball) -XXX = (Ball) -XX = (Diaphragm) (1/8 x 2-1/8 (1/8 x 1-5/8 Diaphragm Qty [Mtl] Diaphragm Qty [Mtl] Qty [Mtl] Qty [Mtl] o.d.) o.d.) -XXX -XXX = (Diaphragm) -XX XX X (2) [SP] (4) [E] (4) [E] -XXC XXC XC C (2) [H] Y (4) [V] Y (4) [V] -XXG XXG XG (2) [B] Y (4) [B] Y (4) [B] -XXL XXL XL L (2) [L] (2) [SP] (4) [T] (4) [T] -XXM XXM XM M (2) [MSp] (4) [E] (4) [E] -XXT XXT XT T (2) [T] (2) [SP] (4) [T] (4) [T] -XXV XXV XV (2) [V] Y (4) [V] Y (4) [V] MNIFOLD / FLUID CP MTERIL OPTIONS PE10P-XXS-XXX-0S PE10P-KS-XXX PE10P-BKS-XXX PVDF (Kynar) PE10P-PS-XXX PE10P-YKS-XXX PE10P-FKS-XXX PE10P-BPS-XXX Polypropylene PE10P-FPS-XXX PE10P-YPS-XXX Item Description (size) Qty Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] 6 Diaphragm Washer (2) [K] [K] [K] [SS] [P] [P] 15 Fluid Cap (2) [K] [K] [K] [SS] [P] [P] 60 Inlet Manifold (1) [ ] [K] [K] [K] [U] [SS] [P] [P] 61 Outlet Manifold (1) [ ] [K] [K] [K] [U] [SS] [P] [P] For NPTF thread models (PE10P-KS-XXX-0S), use -2. For BSP thread models (PE10P-BKS-XXX-0S), use -4. U For NPTF thread models (PE10P-PS-XXX-0S), use -1. For BSP thread models (PE10P-BPS-XXX-0S), use -3 COMMON PRTS Item Description (size) Qty Part No. [Mtl] Item Description (size) Qty Part No. [Mtl] 1 Rod (1) [C] 70 Gasket (2) [B] 5 Backup Washer (2) [SS] 74 Pipe Plug (1/4-18 NPT x 7/16") (2) [K] 26 Screw (M8 x g x 30 mm) (16) [SS] 131 Screw (M8 x g x 100 mm) (4) [SS] 27 Screw (M8 x g x 50 mm) (20) [SS] 144 "U Cup (3/16 x 1-1/8 o.d.) (2) Y [B] 28 Washer (8.5 mm i.d.) (4) [SS] 175 "O Ring (3/32 x 13/16 o.d.) (2) Y [B] 29 Flange Nut (M8 x h) (20) [SS] 180 "O Ring (2.5 mm x 12 mm o.d.) (8) [B] 68 ir Cap (1) [P] 195 Hex Flange Nut (M8 x h) (4) [SS] 69 ir Cap (1) [P] ir Section Service Kit parts, see page 6. Page 4 of 8

5 PRTS LIST/ FLUID SECTION (models PE10P-XS-XXX-0S and PE10P-BXS-XXX-0S) (models PE10P-YXS-XXX-0S) 26,U FOR THE IR MOTOR SECTION SEEPGES6& Torque Sequence COLOR CODE DIPHRGM BLL MTERIL COLOR COLOR ,x 70k 61 (models PE10P-FXS-XXX-0S) 144k 70k 69 27U Hytrel Cream Cream Nitrile Black Red(S) Santoprene Tan Tan Santoprene Green N/ (Backup) PTFE White White Viton Yellow(-) Yellow(S) (-)Dash (S)Dot , 74s 144k 175k 175k VIEW OF TWO PIECE PTFE DIPHRGM (Santoprene) 8 7 (PTFE) k k 195 1k 5 26,U 60 (models PE10P-FXS-XXX-0S) 60 (models PE10P-YXS-XXX-0S) 60 (models PE10P-XS-XXX-0S and PE10P-BXS-XXX-0S) UXILIRY VIEW - 6, Figure TORQUE REQUIREMENTS, NOTE: DO NOT OVERTIGHTEN FSTENERS. LL FSTENERS RE METRIC. (6)Diaphragmwasher,25-30ftlbs( Nm),lubricate face with Lubriplate grease and apply LoctiteR 271 to threads. (26)Screws,10-12ftlbs( Nm). (29)Nuts,10-12ftlbs( Nm). (131)Screws,tightento11-14ftlbs( Nm). LUBRICTION/ SELNTS k pplylubriplatefml-2greasetoall O rings, U cups& mating parts. x pply Loctite 242 to threads at assembly. U pply anti-seize compound to threads and bolt and nut flange heads which contact pump case when using stainless steel fasteners. s pplyptfetapetothreadsatassembly Z Lubriplate FML-2 is a white food grade petroleum grease. Page 5of8

6 PRTS LIST/ IR SECTION n Indicatespartsincludedin637412irSectionServiceKitshownbelowanditems(70),(144),(175)and(180)shownonpage4. IR MOTOR PRTS Item Description(size) Qty Part No. [Mtl] Item Description(size) Qty Part No. [Mtl] 101 Center Body (1) [P] 103 Bushing (1) [D] 121 Plug (2) [D] n 132 Gasket (1) [B] 133 Washer(M6) (6) [SS] 134 Screw(M6x1-6gx25mm) (6) [SS] 160 ir Manifold (1) [] n 166 Gasket (1) [B] n 173 O Ring(3/32 x 1-3/8 o.d.) (2) Y [B] K FluidSectionServiceKitparts,seepage4. n 176 Diaphragm(check valve) (2) [SP] 181 Roll Pin(5/32 o.d. x 1/2 long) (4) Y S [SS] 201 Muffler (1) [P] L n Lubriplate FML-2 Grease (1) Lubriplate Grease Packets(10) MTERIL CODE [] = luminum [D] = cetal [SP] = Santoprene [B] = Nitrile [P] = Polypropylene [SS] = Stainless Steel IR MOTOR SECTION SERVICE GENERL RESSEMBLY NOTES: S ir Motor Section Service is continued from Fluid Section repair. S Inspect and replace old parts with new parts as necessary. Look for deepscratchesonsurfaces,andnicksorcutsin O rings. S Take precautions to prevent cutting O rings upon installation. S Lubricate O rings with Lubriplate FML-2 grease. S Do not over-tighten fasteners, refer to torque specification block on view. S Re-torque fasteners following restart. IR MOTOR SECTION DISSSEMBLY 1. Remove(160) air manifold, exposing(132 and 166) gaskets and (176) checks. 2. Remove(121) plugs. IR MOTOR SECTION RESSEMBLY 1. Clean and lubricate parts not being replaced from service kit. 2. Replace(173) O rings and assemble(121) plugs. 3. ssemble(132and166)gasketsand(176)checksto(101)body. 4. ssemble (160) air manifold to (101) body, securing with (134) screws.note:tighten(134)screwsto35-40in.lbs( nm). Page 6of8

7 PRTS LIST/ IR SECTION 166k k 173k U k 176k Figure 3. TORQUE REQUIREMENTS, NOTE: DO NOT OVERTIGHTEN FSTENERS. LL FSTENERS RE METRIC. Torque(134)screwto35-40in.lbs( Nm). LUBRICTION/ SELNTS k pply Lubriplate FML-2 grease to O rings, U Cups& mating parts. U pply anti-seize compound to threads at assembly. TROUBLE SHOOTING Product discharged from exhaust outlet. S Check for diaphragm rupture. S Check tightness of(6) diaphragm washer. ir bubbles in product discharge. S Check connections of suction plumbing. S Check O rings between intake manifold and inlet side fluid caps. S Check tightness of(6) diaphragm washer. Motor blows air or stalls. S Check(176) check valve for damage or wear. S Check for restrictions in valve/ exhaust. Low output volume, erratic flow, or no flow. S Check air supply. S Check for plugged outlet hose. S Check for kinked(restrictive) outlet material hose. S Check for kinked(restrictive) or collapsed inlet material hose. S Checkforpumpcavitation--suctionpipeshouldbesizedatleastas largeastheinletthreaddiameterofthepumpforproperflowifhigh viscosity fluids are being pumped. Suction hose must be a non-collapsing type, capable of pulling a high vacuum. S Check all joints on the inlet manifolds and suction connections. Thesemustbeairtight. S Inspect the pump for solid objects lodged in the diaphragm chamber ortheseatarea. Page 7of8

8 (Dimensions shown are for reference only, they are displayed in inches and millimeters(mm). DIMENSIONS - seebelow E- 9-23/32 (246.7mm) J- 6-9/32 (159.6mm) N- 7-5/8 (193.9mm) S- 5-1/32 (127.6mm) B /32 (349.8mm) F- 8-5/16 (211.1mm) K- 7/16 (11.1mm) P- seebelow T- 8-3/8 (212.9mm) C- 10-1/16 (255.3mm) G- seebelow L- seebelow Q- seebelow U- 1-3/64 (26.6mm) D- 2-11/32 (59.4mm) H- 5-1/32 (127.6mm) M- 1/2 (12.7mm) R /32 (364.0mm) V- 17/32 (13.3mm) G L Q P PE10P-XS-, BXS- 14-7/32 (361.2 mm) 14-27/32 (376.5 mm) 2 (50.8 mm) 2-3/8 (59.7 mm) 6-31/32 (176.6 mm) PE10P-FXS-XXX-0S 16-1/32 (407.3 mm) 16-1/32 (407.0 mm) /16 (103.0 mm) 8-9/16 (216.9 mm) PE10P-YXS-XXX-0S 14-7/32 (361.2 mm) 16 (406.3 mm) 1-1/32 (25.6 mm) 2-3/8 (59.7 mm) 6-31/32 (176.6 mm) F E L DIMENSIONL DT V U Outlet P /2 N.P.T.F.- 1(PE10P-XS-XXX-0S) Rp 1-11 BS(PE10P-BXS-XXX-0S) B 1/4-18N.P.T.F.-1 G T N Inlet PE10P-XS-XXX-0S PE10P-BXS-XXX-0S D M H J Q S R C K F E 1.N.S.I./DINFlange P U G Outlet 1/4-18N.P.T.F.-1 B T Inlet PE10P-FXS-XXX-0S D N H J M Q K C L E F V Outlet U P 1.N.S.I./DINFlange B 1/4-18N.P.T.F.-1 G T N PE10P-YXS-XXX-0S M H J D Q Inlet S R C K Figure 4 PN Page 8of8