2 DIAPHRAGM PUMP 1:1 RATIO(METALLIC)

Transcription

1 OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION& MAINTENANCE 2 DIAPHRAGM PUMP 1:1 RATIO(METALLIC) READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference. SERVICE KITS Refer to Model Description Chart to match the pump material options XX for fluid section repair(see page 4). NOTE: This kit also contains several air motor seals which will need to be replaced for air section repair(see page 6) major air valve assembly(see page 7). PUMP DATA RELEASED: REVISED: (REV. K) Models... see Model Description Chart for -XXX. Pump Type... Metallic Air Operated Double Diaphragm Material... see Model Description Chart. Weight.. PD20X-XCX-XXX lbs(74.8 kgs) PD20X-AHX-XXX lbs(69.9 kgs) PD20X-ASX-XXX lbs(69.9 kgs) PD20X-BHX-XXX lbs(69.9 kgs) PD20X-BSX-XXX lbs(69.9 kgs) PD20X-FHX-XXX lbs(66.2 kgs) PD20X-FSX-XXX lbs(66.2 kgs) Maximum Air Inlet Pressure psig(8.3 bar) Maximum Material Inlet Pressure psig(0.69 bar) Maximum Outlet Pressure psig(8.3 bar) Maximum Flow Rate(flooded inlet) gpm(644 lpm) Displacement/ Cycle@ 100 psig gal.(5.3 lit.) Maximum Particle Size... 1/4 dia.(6.4 mm) Maximum Temperature Limits(diaphragm/ ball/ seal material) E.P.R./EPDM to280 F(-51 to138 C) Hytrel to180 F(-29 to82 C) Nitrile to180 F(-12 to82 C) Polypropylene to175 F(2 to79 C) PVDF(Kynar ) to200 F(-12 to93 C) Santoprene to225 F(-40 to107 C) PTFE to225 F(4 to107 C) Viton to350 F(-40 to177 C) Dimensional Data... see page 8 Mounting Dimension /16 x 10-1/16 (230 mm x 256 mm) NoiseLevel@70psig,60cpm dB(A)2 ➀ Tested with muffler assembly installed. ➁ The pump sound pressure levels published here have been updated to an Equivalent ContinuousSoundLevel(L Aeq )tomeettheintentofansis ,cagi-pneu- ROP S5.1 using four microphone locations. NOTICE: All possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability. SEAT MATERIAL A -Santoprene C -Hytrel E -CarbonSteel F -Aluminum G -Nitrile MODEL DESCRIPTION CHART AIRMOTOR/AIRCAPMATERIAL R - Polypropylene/ Stainless Steel Y - Polypropylene/ Cast Iron THREAD A /2NPTF-1 B -Rp2(2-11BSPparallel) F -2 ANSI/DINFlange FLUID CAPS& MANIFOLD MATERIAL C -CastIron H -Hastelloy-C S - Stainless Steel HARDWARE MATERIAL P -PlatedSteel S - Stainless Steel BALL MATERIAL A - Santoprene C -Hytrel G -Nitrile H -Hard440StainlessSteel K -PVDF(Kynar) L -Hastelloy-C S -316StainlessSteel S Stainless Steel T -PTFE V -Viton DIAPHRAGM MATERIAL A -Santoprene L - Long Life PTFE C -Hytrel M - Medical Grade Santoprene G -Nitrile T - PTFE / Santoprene Figure 1 PD20X-X X X-X X X V - Viton FLUID SECTION SERVICE KIT SELECTION EXAMPLE: MODEL# PD20Y-ACP-SAA PD20X-XXX-X X X X X FLUID SECTION SERVICE KIT# AA Ball Diaphragm INGERSOLL RAND COMPANY LTD 209 NORTH MAIN STREET BRYAN, OHIO (800) FAX(800) CCN arozone.com

2 OPERATING AND SAFETY PRECAUTIONS READ, UNDERSTAND, AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE. EXCESSIVE AIR PRESSURE STATIC SPARK HAZARDOUS MATERIALS HAZARDOUS PRESSURE WARNING EXCESSIVE AIR PRESSURE. Can cause personal injury, pump damage or property damage. Donotexceedthemaximuminletairpressureasstatedonthe pump model plate. Besurematerialhosesandothercomponentsareabletowithstand fluid pressures developed by this pump. Check all hoses for damage or wear. Be certain dispensing device is clean and in proper working condition. WARNING STATIC SPARK. Can cause explosion resulting in severe injury or death. Ground pump and pumping system. Usethepumpgroundingscrewterminalprovided.UseARO part no ground kit or connect a suitable ground wire (12ga.min.)toagoodearthgroundsource. Secure pump, connections and all contact points to avoid vibration and generation of contact or static spark. Consultlocalbuildingcodesandelectricalcodesforspecific grounding requirements. Aftergrounding,periodicallyverifycontinuityofelectricalpath to ground. Test with an ohmmeter from each component(e.g., hoses, pump, clamps, container, spray gun, etc.) to ground to ensure continuity. Ohmmeter should show 0.1 ohms or less. Submersetheoutlethoseend,dispensingvalveordevicein the material being dispensed if possible.(avoid free streaming of material being dispensed.) Usehosesincorporatingastaticwire. Useproperventilation. Keepinflammablesawayfromheat,openflamesandsparks. Keepcontainersclosedwhennotinuse. WARNING Pump exhaust may contain contaminants. Can cause severe injury. Pipe exhaust away from work area and personnel. Intheeventofadiaphragmrupture,materialcanbeforcedout of the air exhaust muffler. Pipetheexhausttoasaferemotelocationwhenpumpinghazardous or inflammable materials. Useagrounded1 minimumi.d.hosebetweenthepumpand the muffler. WARNING HAZARDOUS PRESSURE. Can result in serious injury or property damage. Do not service or clean pump, hoses or dispensing valve while the system is pressurized. Disconnectairsupplylineandrelievepressurefromthesystembyopeningdispensingvalveordeviceand/orcarefully and slowly loosening and removing outlet hose or piping from pump. WARNING HAZARDOUS MATERIALS. Can cause serious injuryorpropertydamage.donotattempttoreturnapumptothe factory or service center that contains hazardous material. Safe handling practices must comply with local and national laws and safety code requirements. ObtainMaterialSafetyDataSheetsonallmaterialsfromthe supplier for proper handling instructions. WARNING EXPLOSION HAZARD. Models containing aluminum wetted parts cannot be used with III.-Trichloroethane, Methylene Chloride or other Halogenated Hydrocarbon solvents which may react and explode. Check pump motor section, fluid caps, manifolds and all wetted parts to assure compatibility before using with solvents of this type. WARNING MISAPPLICATION HAZARD. Do not use models containing aluminum wetted parts with food products for human consumption. Plated parts can contain trace amounts of lead. CAUTION Verify the chemical compatibility of the pump wetted parts and the substance being pumped, flushed or recirculated. Chemical compatibility may change with temperature and concentration of the chemical(s) within the substances being pumped, flushed or circulated. For specific fluid compatibility, consult the chemical manufacturer. CAUTION Maximum temperatures are based on mechanical stress only. Certain chemicals will significantly reduce maximum safe operating temperature. Consult the chemical manufacturer for chemical compatibility and temperature limits.refertopumpdataonpage1ofthismanual. CAUTION Be certain all operators of this equipment have been trained for safe working practices, understand it s limitations, and wear safety goggles/ equipment when required. CAUTION Do not use the pump for the structural support of the piping system. Be certain the system components are properly supported to prevent stress on the pump parts. Suctionanddischargeconnectionsshouldbeflexibleconnections(such as hose), not rigid piped, and should be compatible with the substance being pumped. CAUTION Prevent unnecessary damage to the pump. Do notallowpumptooperatewhenoutofmaterialforlongperiods of time. Disconnectairlinefrompumpwhensystemsitsidleforlong periods of time. CAUTION Use only genuine ARO replacement parts to assure compatible pressure rating and longest service life. NOTICE Replacement warning labels are available upon request: Static Spark& Diaphragm Rupture pn\ WARNING CAUTION NOTICE = Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. = Hazards or unsafe practices which could result in minor personal injury, product or property damage. = Important installation, operation or maintenance information. Page 2of8

3 GENERAL DESCRIPTION TheAROdiaphragmpumpoffershighvolumedeliveryevenatlowair pressure and a broad range of material compatibility options available. Refer to the model and option chart. ARO pumps feature stall resistant design, modular air motor/ fluid sections. Air operated double diaphragm pumps utilize a pressure differential in the air chambers to alternately create suction and positive fluid pressure in the fluid chambers, valve checks ensure a positive flow of fluid. Pumpcyclingwillbeginasairpressureisappliedanditwillcontinueto pumpandkeepupwiththedemand.itwillbuildandmaintainlinepressure and will stop cycling once maximum line pressure is reached(dispensing device closed) and will resume pumping as needed. AIR AND LUBE REQUIREMENTS WARNING EXCESSIVE AIR PRESSURE. Can cause pump damage, personal injury or property damage. Afiltercapableoffilteringoutparticleslargerthan50micronsshould beusedontheairsupply.thereisnolubricationrequiredotherthan the O ring lubricant which is applied during assembly or repair. Iflubricatedairispresent,makesurethatitiscompatiblewiththe Nitrile O ringsintheairmotorsectionofthepump. OPERATING INSTRUCTIONS Alwaysflushthepumpwithasolventcompatiblewiththematerial being pumped if the material being pumped is subject to setting up whennotinuseforaperiodoftime. Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew hours. Theoutletmaterialvolumeisgovernednotonlybytheairsupplybut also by the material supply available at the inlet. The material supply tubingshouldnotbetoosmallorrestrictive.besurenottousehose which might collapse. Whenthediaphragmpumpisusedinaforced-feed(floodedinlet) situation it is recommended that a Check Valve be installed at the air inlet. Securethediaphragmpumplegstoasuitablesurfacetoensure against damage by vibration. PARTS AND SERVICE KITS Refertothepartviewsanddescriptionsasprovidedonpage4through7 for parts identification and Service Kit information. CertainARO SmartParts areindicatedwhichshouldbeavailable for fast repair and reduction of down time. Servicekitsaredividedtoservicetwoseparatediaphragmpump functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SEC- TION is divided further to match typical part MATERIAL OPTIONS. MAINTENANCE Provideacleanworksurfacetoprotectsensitiveinternalmoving parts from contamination from dirt and foreign matter during service disassembly and reassembly. Keepgoodrecordsofserviceactivityandincludepumpinpreventive maintenance program. Beforedisassembling,emptycapturedmaterialintheoutletmanifoldbyturningthepumpupsidedowntodrainmaterialfromthe pump. FLUID SECTION DISASSEMBLY 1. Remove(61) outlet manifold,(60) inlet manifold. 2. Remove(22) balls,(19) O rings(if applicable) and(21) seats. 3. Remove(15) fluid caps. NOTE: Only PTFE diaphragm models use a primary diaphragm(7) and abackupdiaphragm(8).refertotheauxiliaryviewinthefluidsection illustration. 4. Removethe(6)diaphragmwasher,(7)or(7/8)diaphragms,and(5) backup washer. NOTE:Donotscratchormarthesurfaceof(1)diaphragmrod. FLUID SECTION REASSEMBLY Reassembleinreverseorder.Refertothetorquerequirementson page 5. Cleanandinspectallparts.Replacewornordamagedpartswith new parts as required. Lubricate(1)diaphragmrodand(144) U cupwithlubriplate FML-2 grease(94276 grease packet is included in service kit). FormodelswithPTFEdiaphragms:Item(8)Santoprenediaphragm isinstalledwiththesidemarked AIRSIDE towardsthepumpcenter body. Install the PTFE diaphragm (7) with the side marked FLUID SIDE towards the(15) fluid cap. Re-checktorquesettingsafterpumphasbeenre-startedandruna while. Viton andhytrel aretrademarksofthedupontcompany, Kynar isaregisteredtrademarkofpenwaltcorp. Santoprene isaregisteredtrademarkofmonsantocompany,licensedtoadvancedelastomersystems,l.p., Lubriplate isaregisteredtrademarkoflubriplatedivision(fiskebrothers) Page 3of8

4 PARTS LIST/ PD20X-X-X FLUID SECTION FLUID SECTION SERVICE KITS( XX) KITSINCLUDE:BALLS(seeBallOption,referto-XXinchartbelow),DIAPHRAGMS(seeDiaphragmOption,referto-XXinchartbelow),anditems 19, 70, 144, 175,(listed below) plus 174 and Lubriplate FML-2 grease(page 6). SEAT OPTIONS PD20X-XXX-XXX BALL OPTIONS PD20X-XXX-XXX (2-1/2 dia.) -XXX Seat Qty [Mtl] -XXX Seat Qty [Mtl] -XXX Ball Qty [Mtl] -XXX Ball Qty [Mtl] -AXX A (4) [SP] -HXX (4) [SH] -XAX A (4) [SP] -XSX (4) [SS] -CXX C (4) [H] -KXX K (4) [K] -XCX C (4) [H] -XTX (4) [T] -EXX (4) [C] -LXX (4) [Ha] -XGX (4) [B] -XVX (4) [V] -FXX (4) [A] -SXX (4) [SS] -GXX G -XXX (4) [B] DIAPHRAGM OPTIONS PD20X-XXX-XXX ServiceKit XX=(Ball) -XX =(Diaphragm) Diaphragm Qty [Mtl] Diaphragm Qty [Mtl] O Ring (1/8 x 3-5/8 o.d.) Qty [Mtl] -XXA XA A (2) [SP] (4) [E] -XXC XC C (2) [H] Y (4) [V] -XXG XG (2) [B] Y (4) [B] -XXL XL L (2) [L] A (2) [SP] Y (4) [T] -XXM XM M (2) [MSP] Y (4) [T] -XXT XT T (2) [T] A (2) [SP] Y (4) [T] -XXV XV (2) [V] Y (4) [V] NOTE:Seatoptions-AXX,-CXXand-GXXdonotrequireitem19 O ring. MATERIAL CODE [A] = Aluminum [B] = Nitrile [C] = Carbon Steel [Co] = Copper [CI] =CastIron [E] = E.P.R. [H] = Hytrel [Ha] = Hastelloy - C [L] = Long Life PTFE [K] = PVDF (Kynar) [MSP]= Medical Grade Santoprene [SH] = Hard Stainless Steel [SP] = Santoprene [SS] = Stainless Steel [T] = PTFE [V] = Viton MANIFOLD THREAD/ FLUID CAP MATERIAL OPTIONS PD20X-XXX-XXX PD20X-XCX- PD20X-XHX- PD20X-FHX- PD20X-XSX- PD20X-FSX- Item Description(size) Qty Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] 6 Diaphragm Washer (2) [SS] [Ha] [Ha] [SS] [SS] 9 Washer (2) [SS] [Ha] [Ha] [SS] [SS] 14 Screw(5/8-18 x 2-1/2 ) (2) Y5-111-T [SS] [Ha] [Ha] Y5-111-T [SS] Y5-111-T [SS] 15 Fluid Cap (2) [CI] [Ha] [Ha] [SS] [SS] 60 InletManifold (1) ( ) [CI] ( ) [Ha] [Ha] ( ) [SS] [SS] 61 OutletManifold (1) ( ) [CI] ( ) [Ha] [Ha] ( ) [SS] [SS] 63 PipePlug (2-11-1/2NPT) (2) Y17-28-C [C] (R-2,2-11BSP) (2) [C] ForNPTFthreadmodels(PD20X-AXX-XXX),use -1 ForBSPthreadmodels(PD20X-BXX-XXX),use -2 EXTERNAL HARDWARE OPTION PD20X-XXX-XXX PD20X-XXP-XXX PD20X-XXS-XXX Item Description(size) Qty Part No. [Mtl] Part No. [Mtl] 26 Screw(M10 x 1.5-6g x 35 mm) (8) [C] [SS] 27 Screw(M10x1.5-6gx45mm) (16) [C] [SS] 29 Nut(M10 x 1.5-6g) (16) [C] [SS] Flangemodels COMMON PARTS Item Description(size) Qty Part No. [Mtl] Item Description(size) Qty Part No. [Mtl] 1 Rod (1) [C] 5 Backup Washer (2) [SS] 68 Air Cap (models XX-XXX) (1) [SS] (models PD20Y-XXX-XXX) (1) [CI] 69 Air Cap (models XX-XXX) (1) [SS] (models PD20Y-XXX-XXX) (1) [CI] 70 Gasket (2) [B] SmartParts -KeeptheseitemsonhandinadditiontotheServiceKitsforfastrepairandreductionofdowntime. AirMotorKitparts,seepage Pipe Plug (1/4-18 NPT x 0.41 ) (2) Y17-51-S [SS] 131 Screw(M10x1.5-6gx120mm) (4) [C] 144 U Cup (3/16 x1-3/8 o.d.) (2) Y [B] 175 O Ring (3/32 x1 o.d.) (2) Y [B] 180 Washer(0.406 i.d.x0.031 thick) (4) [Co] 181 Roll Pin (0.156 o.d. x 3/4 long) (4) Y S [SS] Page 4of8

5 PARTS LIST/ PD20X-X-X FLUID SECTION 61 (PD20X-FXX-XXX) 61 (PD20X-AXX-XXX) (PD20X-BXX-XXX) 26 COLOR CODE DIAPHRAGM BALL MATERIAL COLOR COLOR Hytrel Cream Cream Nitrile Black Red( ) Santoprene Tan Tan Santoprene Green N/ A (Backup) PTFE White White Viton Yellow(-) Yellow( ) (-)Dash ( )Dot FOR THE AIR MOTOR SECTION SEEPAGES6& Torque Sequence (PD20X-AXX-XXX) (PD20X-BXX-XXX) (PD20X-FXX-XXX) (PTFE) (Santoprene) 8 VIEW OF TWO PIECE PTFE DIAPHRAGM Figure 2 TORQUEREQUIREMENTS NOTE: DO NOT OVERTIGHTEN FASTENERS. ALL FASTENERS ARE METRIC. (14) Diaphragm screw, apply Loctite#271 to threads, 65-70ftlbs( Nm). (26and27)Fluidcaps/manifoldscrews30-40ftlbs ( Nm). (131)Screw35-40ftlbs( Nm). Applyanti-seizecompoundtothreadswhenusing stainless steel fasteners and stainless steel wetends. LUBRICATION/ SEALANTS ApplyLubriplateFML-2greasetoall O rings, U Cups&matingparts. ApplyLoctite242tothreadsatassembly. ApplyPTFEtapetothreadsatassembly. NotusedwithPD20X-XXX-AXX,-CXX&-GXX. LubriplateFML-2isawhitefoodgradepetroleumgrease. Page 5of8

6 PARTS LIST/ PD20X-X-X AIR SECTION Indicatespartsincludedin637369AirSectionServiceKitshownbelowanditems(70),(144),(175)and(180)shownonpage4. AIR MOTOR PARTS Item Description(size) Qty Part No. [Mtl] Item Description(size) Qty Part No. [Mtl] 101 Center Body (1) [P] 103 Bushing (1) [D] 105 Screw(M6x1-6gx180mm) (4) [SS] 107 End Plate (2) [SS] 111 Spool (1) [D] 118 Actuator Pin (0.250 x long) (2) [SS] 121 Sleeve (2) [D] St.Elbow(1-1/2-11-1/2NPT) (1) [C/I] 132 Gasket (1) [B] 133 Washer(M6) (8) [SS] 134 Screw(M6x1-6gx35mm) (8) [SS] 135 Valve Block (1) [P] 136 End Cap (1) [P] 137 O Ring (1/16 x2 o.d.) (1) Y [B] 138 U Cup (3/16 x1.792 o.d.) (1) [B] 139 U Cup (3/16 x1-1/4 o.d.) (1) Y [B] 140 Valve Insert (1) [Ck] 141 Valve Plate (1) [Ck] 146 O Ring (1/8 x7/8 o.d.) (1) Y [B] 147 O Ring (1/8 x5/8 o.d.) (1) Y [B] 166 TrackGasket (1) [B] 167 PilotPiston (includes168and169) (1) [D] FluidSectionServiceKitparts,seepage O Ring (3/32 x 5/8 o.d.) (2) [U] 169 U Cup (1/8 x 7/8 o.d.) (1) Y240-9 [B] 170 Piston Sleeve (1) [D] 171 O Ring (3/32 x1-1/8 o.d.) (1) Y [B] 172 O Ring (1/16 x1-1/8 o.d.) (1) Y [B] 173 O Ring (1/16 x1-3/8 o.d.) (2) Y [B] 174 O Ring (1/8 x1/2 o.d.) (2) Y [B] 176 Diaphragm (checkvalve) (2) [SP] 199 TrackGasket (1) [B] 200 Gasket (1) [B] 201 Muffler (1) O Ring (1/8 x1/2 o.d.) (2) Y [B] 233 Adapter Plate (1) [P] 236 Nut(M6x1-6g) (4) [SS] LubriplateFML-2Grease (1) Lubriplate Grease Packets(10) Itemsnotshown MATERIAL CODE [B] = Nitrile [D] = Acetal [SP] = Santoprene [Br] = Brass [I] = Iron [SS] = Stainless Steel [C] = Carbon Steel [P] = Polypropylene [U] = Polyurethane [Ck] = Ceramic AIR MOTOR SECTION SERVICE Serviceisdividedintotwoparts -1.PilotValve,2.MajorValve. GENERAL REASSEMBLY NOTES: AirMotorSectionServiceiscontinuedfromFluidSectionrepair. Inspectandreplaceoldpartswithnewpartsasnecessary.Lookfor deepscratchesonsurfaces,andnicksorcutsin O rings. Takeprecautionstopreventcutting O ringsuponinstallation. Lubricate O ringswithlubriplatefml-2grease. Donotover-tightenfasteners,refertotorquespecificationblockon view. Re-torquefastenersfollowingrestart. SERVICETOOLS -Toaidintheinstallationof(168) O ringsonto the(167) pilot piston, use tool# T, available from ARO. PILOT VALVE DISASSEMBLY 1. Alighttapon(118)shouldexposetheopposite(121)sleeve,(167) pilot piston and other parts. 2. Remove(170) sleeve, inspect inner bore of sleeve for damage. PILOT VALVE REASSEMBLY 1. Clean and lubricate parts not being replaced from service kit. 2. Install new(171 and 172) O rings, replace(170) sleeve. 3. Installnew(168) O ringsand(169)seal-notethelipdirection.lubricate and replace(167). 4. Reassemble remaining parts, replace(173 and 174) O rings. MAJOR VALVE DISASSEMBLY 1. Remove(135) valve block and(233) adapter plate, exposing(132 and 166) gaskets,(232) O ring and(176) checks. 2. Remove (233) adapter plate, releasing (140) valve insert, (141) valveplate,(199and200)gasketsand(146,147and232) O rings. 3. Remove(136)endcapand(137) O ring,releasing(111)spool. MAJOR VALVE REASSEMBLY 1. Installnew(138and139) U cupson(111)spool - LIPSMUST FACE EACH OTHER. 2. Insert(111) spool into(135) valve block. 3. Install(137) O ringon(136)endcapandassembleendcapto (135) valve block, securing with(107) end plates and(105) screws. 4. Install(140) valve insert and(141) valve plate into(135) valve block. NOTE: Assemble(140) valve insert with dished side toward(141) valve plate. Assemble(141) valve plate with 2 identification dots toward(199 and 200) gaskets. 5. Assemble(146,147and232) O rings,(199and200)gasketsand (233) adapter plate to(135) valve block. 6. Assemble(132and166)gaskets,(176)checksand(232) O ringto (101) body. 7. Assemble(135) valve block and components to(101) body, securing with(134) screws. Page 6of8

7 PARTS LIST/ PD20X-X-X AIR SECTION PILOT VALVE PART GROUP Optional Muffler 138 MAJOR VALVE TORQUEREQUIREMENTS NOTE: DO NOT OVERTIGHTEN FASTENERS. ALL FASTENERS ARE METRIC. Torque(105)screwto35-40in.lbs( Nm). Torque(134)screwto35-40in.lbs( Nm). LUBRICATION/ SEALANTS ApplyLubriplateFML-2greaseto O rings, U Cups & mating parts. A replacement Major Valve Service Assembly is available separately, which includes the following: 105(4),107(2),111,132,135,136,137,138,139,140,141,146,147,166,176(2),199,200,232(2),233and236(4) Figure 3 Page 7of8

8 TROUBLESHOOTING Product discharged from exhaust outlet. Checkfordiaphragmrupture. Checktightnessof(14)diaphragmscrew. Air bubbles in product discharge. Checkconnectionsofsuctionplumbing. Check O ringsbetweenintakemanifoldandinletsidefluidcaps. Checktightnessof(14)diaphragmscrew. Motor blows air or stalls. Check(176)checkvalvefordamageorwear. Checkforrestrictionsinvalve/exhaust. Low output volume, erratic flow, or no flow. Checkairsupply. Checkforpluggedoutlethose. Checkforkinked(restrictive)outletmaterialhose. Checkforkinked(restrictive)orcollapsedinletmaterialhose. Checkforpumpcavitation -suctionpipeshouldbesizedatleastas largeastheinletthreaddiameterofthepumpforproperflowifhigh viscosity fluids are being pumped. Suction hose must be a non-collapsing type, capable of pulling a high vacuum. Check all joints on the inlet manifolds and suction connections. Thesemustbeairtight. Inspectthepumpforsolidobjectsloggedinthediaphragmchamber ortheseatarea. DIMENSIONAL DATA L (Dimensions shown are for reference only, they are displayed in inches and millimeters(mm). P E F L (PD20X-AXX-XXX)2-11-1/2NPTF-1 (PD20X-BXX-XXX)Rp2(2-11BSPparallel) Outlet N Bolt Circle B Q G AirInlet3/4-14NPT B R M Dotted lines show optional muffler assembly. H J D 2 ANSI/DINFlange (PD20X-FXX-XXX) D K Inlet C A Exhaust Port 1-1/2-11-1/2 N.P.S.M. DIMENSIONS A- seebelow E- 16-3/16 (411.2mm) J- 10-1/16 (255.6mm) N (122.8mm) B- 24-3/4 (628.7mm) F- 12 (304.8mm) K- 9/16 (14.3mm) P- 21-5/8 (548mm) C- 10-1/16 (255.6mm) G- 26-1/4 (666.8mm) L- seebelow Q- 27-7/8 (708.0mm) D- seebelow H- 9-1/16 (230.2mm) M- 5/8 (15.9mm) R- 13-9/16 (344.5mm) A D L PD20X-XCX-XXX 19-3/4 (501.4 mm) 1-7/8 (47.6 mm) 2 (50.8 mm) PD20X-AHX-XXX 19-3/8 (492.1 mm) 2-1/2 (63.5 mm) 2-3/32 (53.0 mm) PD20X-ASX-XXX 19-3/8 (492.1 mm) 2-1/2 (63.5 mm) 2-3/32 (53.0 mm) PD20X-BHX-XXX 19-3/8 (492.1 mm) 2-1/2 (63.5 mm) 2-3/32 (53.0 mm) PD20X-BSX-XXX 19-3/8 (492.1 mm) 2-1/2 (63.5 mm) 2-3/32 (53.0 mm) PD20X-FHX-XXX 19-3/8 (492.1 mm) 2-1/2 (63.5 mm) 3-1/4 (82.6 mm) PD20X-FSX-XXX 19-3/8 (492.1 mm) 2-1/2 (63.5 mm) 3-1/4 (82.6 mm) Figure 4 Page 8of8 PN