Sure Grip Left Foot Gas Pedals A202. with
|
|
- Terence Bell
- 5 years ago
- Views:
Transcription
1 Sure Grip Left Foot Gas Pedals A202 with
2 The A202 Left Foot Gas Pedal Sure Foot was designed to offer you a left foot gas pedal which acts exactly like your vehicle s existing gas pedal. Sure Foot removable features a quickrelease base so the entire assembly can be removed and re-installed quickly and easily. To remove the gas pedal, simply loosen the thumbscrew and lift the entire main assembly off the base. To re-install sure foot removable, place the main assembly on the base (two locator pins helps you line up the holes) and tighten the thumbscrew.
3 Components Left Foot Gas Main Block Quick Release Knob Base Plate Adjustable Roller Arm Gas Pedal Roller Gas Pedal Guard Rocker Arm
4 Installation : Prep When putting the A202 in a vehicle be sure to speak with the vehicles owner and explain that holes must be drilled in the floor of the vehicle in order to do the installation. You should also find out the owners preference as to if they would like the pedal to be installed over their floor mats. An obstacle to installation can be the foot rest that is in many automatic vehicles where the clutch would be in standard transmission cars. In many vehicles this is a plastic mold that can be clipped out, but in others it may be part of the structure. This is also something that should be discussed with the vehicles owner.
5 Installation: Position There are 3 things to keep in mind when setting the position of the A202: 1. Make sure to position the left foot gas pedal the same distance from the brake as the right foot gas pedal. 2. Make sure to angle the left foot gas on the same plane as the right foot gas. 3. Be sure that you will not be drilling into any OEM lines when drilling in the set screws.
6 Installation: Base Plate Caution: Be sure to know where wires, cables, and air ducts are before you drill holes in the floor of the vehicle. Once you have your desired position remove the main assembly from the base plate. You can then use the four set screws to anchor it into place.
7 Installation: Reattach the Main Body Once you have the base plate anchored down you can then reattach the main body and secure it. It is then time to position the roller arm and the left foot gas pedal (LFGP).
8 Installation: Final Position (Roller) The final positioning of the roller arm can be done in two steps: 1. Use an Allen key to loosen the rocker arm washer and proceed to position the roller arm. 2. Tighten down the rocker arm washer. Test the travel of the roller to ensure that it will stay on the pedal when depressed and that you will be able to achieve full acceleration. If necessary use an alternate hole for the roller itself and test again.
9 Installation: Final Position LFGP Use a ½ socket to adjust the LFGP. Once the two bolts are loose you can adjust distance from the from the brake pedal and the angle of the LFGP. The goal is to adjust the LFGP so that it is the mirror image of the right foot gas pedal. When you have achieved the desired position retighten the bolts. Be sure to get customer feedback as they may have preferences as to how the LFGP is positioned.
10 Installation: Pedal Guard Use the clamping bracket to attach the pedal guard. Once you have tighten the bolts down, position the brace so that it sits against the fire wall. Cut off any access brace that it protruding outward.
11 Final Check Pedal is in Proper Position Gas Roller Maintains Contact with OEM Pedal Vehicle Returns to Normal Idle Guard Cannot be Push Towards Gas Pedal All Fasteners are Properly Tightened
12 Thank you for your time! There are many valuable recourses on as installation photos, training resources, product information, installation instructions and more Also take the time to ask about our training program called Sure Grip U, a new and innovative way to prepare your team. Suregrip@suregrip-hvl.com Call Fax
BMW E9x M3 Skid Plate Installation Instructions
BMW E9x M3 Skid Plate Installation Instructions Introducing the new Turner E9x M3 Skid Plate! The Turner engineering team set out to design a no-compromise belly pan replacement which requires no modification
More informationInstallation Instructions
FORD #3100 SuperRail Mounting Kit #3123 Gross Trailer Weight (Maximum)...12,000 lbs. Vertical Load Weight (Max. Pin Weight)...3,000 lbs. Installation Instructions SPECIFICATIONS Fits 2015-2018 Ford F-150
More informationAccelerator Pedal or Lever Position Sensor Circuit
Page 1 of 9 019-086 Accelerator Pedal or Lever Position Sensor Circuit Initial Check CAUTION Do not use probes or leads other than Part No. 3822758. The OEM connector will be damaged. The leads must fit
More informationThank you for purchasing your new ECS Tuning Adjustable Clutch Pedal Stop, we appreciate your business! Project Overview:
Skill Level 1 - Easy Volkswagen Adjustable Pedal Stop Installation Instructions - ES3247980 Thank you for purchasing your new ECS Tuning Adjustable Pedal Stop, we appreciate your business! Project Overview:
More informationJakes Big Block Conversion Kit (P/N 7216)
Jakes Big Block Conversion Kit (P/N 7216) Before beginning be sure to read and understand the instructions. This kit is designed to give you maximum torque for those extreme off-road conditions. We thank
More informationInstallation instructions for Camaro/Firebird and Nova* Windshield Wiper Systems
Installation instructions for 1967-69 Camaro/Firebird and 1968-74 Nova* Windshield Wiper Systems The Raingear 1967-69 Camaro/Firebird and 1964-74 Nova wiper system is designed for ease of installation
More informationHAND THROTTLE KIT For Workman 3000 Series
FORM NO. 7 6 MODEL NO. 0746 INSTALLATION INSTRUCTIONS HAND THROTTLE KIT For Workman 000 Series. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition
More informationDODGE. 12K Custom SuperRail Mounting Kit #3122. Gross Trailer Weight (Maximum)...12,000 lbs. Vertical Load Weight (Max. Pin Weight)...3,000 lbs.
DODGE 12K Custom SuperRail Mounting Kit #3122 Gross Trailer Weight (Maximum)...12,000 lbs. Vertical Load Weight (Max. Pin Weight)...3,000 lbs. Installation Instructions SPECIFICATIONS Fits 2009-2018 Dodge1500
More informationHAND CONTROL SYSTEM FOR THE PHYSICALLY DISABLED
INSTALLATION Push/Twist HAND CONTROL SYSTEM FOR THE PHYSICALLY DISABLED with Howell Ventures Ltd Sure Grip Hand Control Systems and Accessories are warranted against manufacturing or material defects for
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationTo safely lift and install this hardtop, you will need the assistance of at least one other person.! WARNING
1987-1995 Jeep Wrangler YJ Hardtop with Half Doors Installation Instructions PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION To safely lift and install this hardtop, you will need the assistance of
More informationFORD SuperRail Mounting Kit #3111
FORD SuperRail Mounting Kit #3111 #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 12,000 lbs. 3,000 lbs. Installation Instructions SPECIFICATIONS Fits 2001-2003
More informationINSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only)
INSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No. 61770 for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only) Warn Light Bar 61090 and many other grille guards can be mounted
More informationInstallation instructions, accessories. Electric engine block heater, connector outlet, 4-cyl
Installation instructions, accessories Instruction No 31359444 Version 1.2 5 Part. No. 31359438 Electric engine block heater, connector outlet, 4-cyl IMG-247665 Volvo Car Corporation Electric engine block
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More informationCONTROL SYSTEM FOR THE PHYSICALLY DISABLED
INSTALLATION Push/Rock HAND CONTROL SYSTEM FOR THE PHYSICALLY DISABLED With Howell Ventures Ltd Sure Grip Hand Control Systems and Accessories are warranted against manufacturing or material defects for
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More information2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions
2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set
More informationFORD SuperRail Mounting Kit #3113. #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) SPECIFICATIONS
FORD SuperRail Mounting Kit #3113 #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 12,000 lbs. 3,000 lbs. Installation Instructions SPECIFICATIONS Fits 2004-2008
More informationInstallation Instructions Models 2858, 2858A-1, 2858GL February 2009
Installation Instructions Models 2858, 2858A-1, 2858GL February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 Step 1 Head Assembly Installation Instructions
More informationInstallation Instructions February 2009
Installation Instructions February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 The Hammer Head Assembly Installation Instructions (Rollerbar & Direct
More informationMACE ENGINENEERING GROUP VN-VS V8 COLD AIR INTAKE FITTING INSTRUCTIONS COLD AIR INTAKE KIT TO SUIT HOLDEN VN-VS. Fitting Instructions
COLD AIR INTAKE KIT TO SUIT HOLDEN VN-VS V8 Fitting Instructions PART 1: REMOVING STANDARD AIR BOX The position of the airbox is shown below. Note that VR-VS models have the washer bottle in front; earlier
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 36030 Product Description: BULL BAR WINCH TYPE Suited to vehicle/s: CHEVROLET C/K 500-3500 988-998 YEAR MODEL RANGE AND Warn 9,500-5,000lb WINCHES WARNING REGARDING VEHICLES EQUIPPED WITH
More informationLABOUR ESTIMATE GUIDE
INSTALLATION INSTRUCTIONS FOR 2003-Current Audi S4 (B6 & B7) Includes Sedan, Avant, & Cabriolet These instructions are applicable to vehicles equipped with either manual or automatic tiptronic transmissions
More informationBe sure to read and go over all pages before you start your installation
Yamaha Gen-2 V-MaxV Holeshot Superbike Bars Installation Guide Pre-Installation Note Be sure to read and go over all pages before you start your installation Preparation for Installation A) It is recommended
More informationWARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.
WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationCHEVY/GMC SuperRail Mounting Kit #4428
CHEVY/GMC SuperRail Mounting Kit #4428 #4100 SuperGlide (16K) #4400 SuperGlide (20K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More information24 Volt - 3/8" Cordless Impact Wrench
24 Volt - 3/8" Cordless Impact Wrench INSTRUCTION MANUAL Item # 3994040 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical equipment such as this, basic safety precautions should always be followed
More information24V Cordless 1/2in. Impact Wrench
24V Cordless 1/2in. Impact Wrench 0110 Thank you very much for choosing a Klutch TM product! For future reference, please complete the owner's record below: Model: Purchase Date: Save the receipt, warranty
More informationSpecifications D3C, D4C AND D5C SERIES III TRACTORS POWER TRAIN. Steering Brake Group Pedal Steer (Standard)
Page 1 of 9 Specifications D3C, D4C AND D5C SERIES III TRACTORS POWER TRAIN Steering Brake Group Pedal Steer (Standard) Page 2 of 9 Torque for all 1/2 in. locknuts that hold rod ends in place on the rods...
More informationInstallation, Operation & Maintenance
OTO Installation, Operation & Maintenance 1 Installation, Operation & Maintenance OTO Curved Slot Swirl Diffusers Last Revision 2016-08 H V A C TM Architecture, Comfort, Efficiency OTO Installation, Operation
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationWinch Mount Kit. For RZR 900 / RZR 1000 Assembly / Owner s Manual Part No
Winch Mount Kit For RZR 900 / RZR 1000 Assembly / Owner s Manual Part No. 25-3360 1 OPERATING INSTRUCTIONS Congratulations! You ve just purchased the most durable accessory component in the industry. Our
More informationINSTALLATION INSTRUCTIONS FOR BRUTE IV EXTREME TM BELT DRIVE
INSTALLATION INSTRUCTIONS FOR BRUTE IV EXTREME TM BELT DRIVE FOR 1990 TO PRESENT EVO & TWIN CAM SOFTAILS Shown w/optional mid-shift control It s common knowledge that a belt drive primary can provide advantages
More informationCold Air Intake Installation Instructions
BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions PARTS LIST: PF BMWE36-4 PROCEDURE: 1. Using a flat-head screwdriver, loosen the hose clamp between the AFM and rubber boot leading to engine
More informationInstallation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies
Installation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies Getting started with the removal of your existing Jeep body. Trust nothing to memory; take photos of everything at different
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit with Adjustable Slave Cylinder INSTALLATION & USER S GUIDE Doc ID: 191-7704A Doc Rev: 102915 OVERVIEW This kit replaces the OEM core clutch components including
More informationINSTALLING THE NEUTRAL SAFETY SWITCH WIRES
Installation Instructions Magnum Grip Pro Bandit Shifter Part Number 81045 & 81046 2004, 2003 by B&M Racing and Performance Products (Visit www.bmracing.com for additional products and product information)
More informationCorkSport ort Mazda 3 Adjustable Shifter Mazdaspeed 3, Mazda 3 6-speed and Mazda3 SkyActiv 6-speed
Part # Axl-6-963 CorkSport ort Mazda 3 Adjustable Shifter 2010-2013 Mazdaspeed 3, 2010-2013 Mazda 3 6-speed and 2012-2013 Mazda3 SkyActiv 6-speed Pre-Installation Notes: The CorkSport Adjustable Short
More information54531/ FORD FUSION
54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill
More informationUser Manual. MB-6000-UD Rev. 1.03
User Manual MB-6000-UD Rev. 1.03 Table of Contents I. The Controls II. III. IV. Unit Operations A. Folding the Unit B. Folding the Handlebars C. Unlocking and Unfolding D. Precautions and Starting E. Power
More informationA/F/X Body GM Installation Instructions
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 68-74 X Body 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand
More informationFTFR Maintenance and Parts Manual SQ-1 FLOOR TRUSS FINISH ROLLER. Operators Manual
FTFR Maintenance and Parts Manual SQ-1 FLOOR TRUSS FINISH ROLLER Operators Manual FOREWORD This manual explains the proper maintenance of Square 1 Design Floor Truss Finish Roller as well as the daily
More informationCONTENTS: 1EA. SUBWOOFER HARNESS 2PIECE TOOLS REQUIRED:
CONTENTS: 1EA. SUBWOOFER ENCLOSURE 1EA. SUBWOOFER HARNESS 2PIECE 2EA. T-TAP 1EA. FUSE 30 AMP 6EA. WIRE TIES 1EA. INSTRUCTIONS P/N 77KICK14SUBASSEMBLY P/N RHPM1 P/N RFTTAPB P/N RFUSE30 P/N RFZIP6 P/N RBI77KICK14
More informationLast Revision: 30JN THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 30JN2007 1969 THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2017 Ford F-250/350 PART NUMBER: 32-3900, 32-3905, 32-3900L, 32-3905L ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 ULTIMATE
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationMACE ENGINENEERING GROUP VN-VS V6 AND L67 COLD AIR INTAKE FITTING INSTRUCTIONS COLD AIR INTAKE. Fitting Instructions
COLD AIR INTAKE KIT TO SUIT HOLDEN VN-VS V6 & L67 Fitting Instructions PART 1 - REMOVAL OF STANDARD AIRBOX Step 1 - Loosen the hose clamp in the position shown Step 2 - The lid of the airbox has 5 clips
More informationEZ LITE CRUISER. Service & Maintenance Manual
EZ LITE CRUISER Service & Maintenance Manual Table Of Contents Introduction to the EZ Lite Cruiser 3 Identification of Components 4 Controller System Component Diagram 6 Controller System I/O Ports Detail
More informationThis is an aluminum-case PowerGlide Transmission out of a 1966 Chevelle.
Removal Procedures ***Take a picture of the transmission and note the lever positions (Transmission Arm Lever points up and Kickdown Lever point down)*** This is an aluminum-case PowerGlide Transmission
More informationWinch Mount Kit. For Honda Pioneer 500 Assembly / Owner s Manual Part No
Winch Mount Kit For Honda Pioneer 500 Assembly / Owner s Manual Part No. 25-1250 1 OPERATING INSTRUCTIONS Congratulations! You ve just purchased the most durable accessory component in the industry. Our
More informationInvacare Action 1 NG Range MAINTENANCE AND ADJUSTMENT
Invacare Action 1 NG Range MAINTENANCE AND ADJUSTMENT Action1 NG Range 1 December 2010 TABLE OF CONTENTS TABLE OF CONTENTS SECTION 1 TROUBLESHOOTING A N D M A I N T E N A N C E.....4 Troubleshooting.....4
More informationCRESTLINE DAMPENING SYSTEM INSTALLATION INSTRUCTIONS. Ryobi 3302M Itek 3985 A.B. Dick 9985 X /99
CRESTLINE DAMPENING SYSTEM INSTALLATION INSTRUCTIONS Ryobi 3302M Itek 3985 A.B. Dick 9985 X88-32 3/99 GENERAL INFORMATION ATTENTION CRESTLINE DAMPENER OWNER Accel Graphic Systems provides parts and service
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Part No. 30090 (black) Part No. 30091 (chrome) for Chev & GMC S-series trucks NOTE: GMC SLE only: This model has a plastic bumper cover which protrudes
More informationBX88175 Installation Instructions ToadStop II Vacuum Brake System
BX88175 Installation Instructions ToadStop II Vacuum Brake System Serial No. Customer supplied tools & supplies Utility knife, 12VDC tester, drill & bits: (1/8", 1/4", 5/8 ), ¼ socket drive bit, punch,
More informationFloor Mat Installation During PDS
T-SB-0040-11 May 20, 2011 Service Category General Section Pre-Delivery Service Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2012 4Runner, Avalon, Camry, Camry HV, Corolla, FJ Cruiser,
More information1969 Camaro. Concourse Style Disc Brake Conversion Kit Instllation Instructions
Concourse Style Disc Brake Conversion Kit Instllation Instructions 1969 Camaro (1970 Chevelle Kit Shown) This document contains our regular disc brake conversion instructions with the addition of GM assembly
More informationFord F-150 Series Rock Slider Side Steps Installation Instructions
2004-2014 Ford F-150 Series Rock Slider Side Steps Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationSpikes-Spider Hub Installation
Spikes-Spider Hub Installation The instructions that are provided with the Spikes Spiders are pretty good. I've created this page for two reasons: to show those that are thinking of buying a set exactly
More information190/195 Tilt Shower Commode User Manual
... 190/195 Tilt Shower Commode User Manual Healthline Products 1065 E Story Rd Winter Garden Florida 34787 Fax 407-656-5641 Toll Free: 800-987-3577 Product Information This series of rehab commodes offer
More informationLow Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2
Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2 Installation Instructions Background: These instructions are designed for installing the 2 body lift. They can also be
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More informationWINCH MOUNT KIT FOR POLARIS RANGER MID-SIZE P/N ASSEMBLY / OWNERS MANUAL. Application WINCH KIT NO. 25-9xxx
WINCH MOUNT KIT FOR POLARIS RANGER MID-SIZE P/N 25-3310 ASSEMBLY / OWNERS MANUAL Application WINCH KIT NO. 25-9xxx Before you begin, please read these instructions and check to be sure all parts and tools
More informationGuide to Installing Y o u r H a r m a r S t a i r L i f t
Guide to Installing Y o u r H a r m a r S t a i r L i f t 2 W E L C O M E T O T H E H A R M A R F A M I L Y Congratulations on your purchase of a Harmar Access Stairway Lift. These instructions will assist
More informationService Manual Large Hi-Low MPS Date Code: 06/15 (Location under seat pan) Date Code
Service Manual Large Hi-Low MPS Date Code: 06/15 (Location under seat pan) Date Code SMHLM(C4)09-15LIT Table of Contents 1. MPS to Base Interface Bolt Replacement...........................................
More informationInstallation Instructions LamboStyleDoors
Installation Instructions LamboStyleDoors (The instruction refers only to one side of the car, but is valid for both sides) Preparations: (Dismantling according to the regulation of the car manufacturer)
More informationK9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN
K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for 2013-2018 FORD INTERCEPTOR SEDAN TOOLS Needed: Phillips Screw Driver Trim panel removal tools Caulk Gun Standard Socket set Metric Socket set Wire Cutters /Crimpers
More informationInstallation Instructions LamboStyleDoors
Installation Instructions LamboStyleDoors (The instruction refers only to one side of the car, but is valid for both sides) Preparations: (Dismantling according to the regulation of the car manufacturer)
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit for Kawasaki KX80/85/100 OVERVIEW INSTALLATION & USER S GUIDE Doc ID: 191-7742A Doc Rev: 073015 This kit replaces the OEM core clutch components including
More informationHEAVY DUTY STAIR LIFT SYSTEM Installation and Service Manual
HEAVY DUTY STAIR LIFT SYSTEM Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTRUCTIONS is required and will promote the safety of installers, as well as those who will
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationPlease try our way first.
1958-1962 Corvette Raingear installation instructions Designer s Note: The 1958-1962 Corvette RainGear wiper system that you have purchased is complex and will require patient fitting. Complete Instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationOWNER S MANUAL MUDRZRDK POLARIS RZR DASH KIT [FOR USE WITH MTX WET-MC3 HEAD UNIT] MTX.COM
OWNER S MANUAL MUDRZRDK POLARIS RZR DASH KIT [FOR USE WITH MTX WET-MC3 HEAD UNIT] IMPORTANT NOTICE If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support at
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
Installation Instructions SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other
More informationKK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel
More information54531/ FORD FUSION
2014-2015 FORD Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill Motor PARTS LIST: (4) #8 u-nuts (2) seal brackets (driver
More informationCold Air Intake Installation Instructions
BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions Page 1/5 3.06 INS264 NOTE: The vehicle shown for this installation is equipped with ASC+T. If your vehicle dos not have this feature, installation
More informationInstallation Instructions for disc brakes
Installation Instructions for disc brakes Bedford CF 230-280, built 1974-1986, not suitable for vehicles with rear twin tyres Included 2 pcs. Wheel Hubs with Wheel Bolts, Mounted Brake Discs and Wheel
More informationEst The First, The Best, Built to Last... INSTALLATION MANUAL STABLE RELIABLE QUALITY
Est. 1948 The First, The Best, Built to Last... STABLE INSTALLATION MANUAL RELIABLE QUALITY 2007 STANDARD INSTALLATION DIAGRAM TRUSTY WARNS, INC 320 E. IRVING PARK RD. WOOD DALE, IL 60191 PH: 630-766-9015
More informationYAMAHA VIPER SX SRX SXR V-MAX XTC CUSTOM LONG TRACK INSTALLATION
YAMAHA VIPER SX SRX SXR V-MAX XTC CUSTOM LONG TRACK INSTALLATION REMOVAL OF OLD TUNNEL EXTENSION AND COOLER 1. Remove plastic bumper covers. 2. Drain coolant by removing left or right rear cooler hose.
More informationRIM Hood For Aeromaster Bodies
RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working
More informationFloor Mat Installation During PDS
T-SB-0029-14 April 17, 2014 Service Category General Section Pre-Delivery Service Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2015 4Runner, Avalon, Avalon HV, Camry, Camry HV, Corolla,
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More informationExploration 4: Rotorcraft Flight and Lift
Exploration 4: Rotorcraft Flight and Lift Students use appropriate terminology to describe the various stages of flight and discover that the lift force changes with the amount of air moved by the rotor
More informationINSTALLATION GUIDE. Doc ID: A Doc Rev:
REKLUSE MOTOR SPORTS EXP Kit for Harley-Davidson Big Twin Hydraulic-Actuated OVERVIEW INSTALLATION GUIDE Doc ID: 191-6200A Doc Rev: 061215 This kit replaces the OEM clutch pack (friction disks and drive
More informationPLEASE READ THESE INSTRUCTIONSFULLY BEFORE STARTING TO ASSEMBLE YOUR DIDICAR PLEASE PAY SPECIAL ATTENTION TO THE NOTES AND HINTS
PLEASE READ THESE INSTRUCTIONSFULLY BEFORE STARTING TO ASSEMBLE YOUR DIDICAR PLEASE PAY SPECIAL ATTENTION TO THE NOTES AND HINTS ASSEMBLY INSTRUCTIONS Parts List iv) i) v) ii) iiib) iiia) vii) i) Car Body
More informationVan Rack Installation Manual Ford Transit Connect
1.888.772.8400 Big to small... We do it all Van Rack Installation Manual Ford Transit Connect Thank you for your purchase of an Unruh Fab Van rack. We have designed and built this rack so that you can
More informationCongratulations on your purchase of a Mobile Ramps and Lifts lift.
2 W E L C O M E T O T H E M O B I L E R A M P S A N D L I F T S Congratulations on your purchase of a Mobile Ramps and Lifts lift. These instructions will assist you in making sure your installation is
More informationINSTALLATION & OWNER S MANUAL
Rev. D, p. 1 of 14 INSTALLATION & OWNER S MANUAL Bobcat CT 230 and KIOTI CK30 cab kit with hard doors and soft rear curtain p/n 1BCT230 & 1KTCK30 The contents of this envelope are the property of the owner.
More informationAvoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket.
HOUSINGS 7808 Thank You For Choosing Küryakyn! Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding
More informationHardcoat Full Tilt Windshield
Hardcoat Full Tilt Windshield For Can-Am Defender P/N 3015 ASSEMBLY / OWNERS MANUAL Before you begin, please read and understand these instructions. Also review the box contents to ensure all parts are
More informationHELIOMOTION QUICK ASSEMBLY GUIDE PV-650
HELIOMOTION QUICK ASSEMBLY GUIDE PV-650 PART I - FOUNDATION M16 M16 8x 2 PLACEMENT 1m Area around flange must be clear of obstacles in a 1 meter radius. Place the unit in a location that receives sunlight
More informationManual Brake Conversion Kit, (MMBAK-13)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com Manual Brake Conversion Kit, 1994-95 (MMBAK-13) The MM kit includes a CNC machined
More information