User Manual. Gear Driven 30 Qt. Commercial Mixer. Models: MX30. Please read and keep these instructions. Indoor use only.
|
|
- Robyn Greene
- 6 years ago
- Views:
Transcription
1 Gear Driven 0 Qt. Commercial Mixer Models: MX0 Shifting gears while this unit is running will void warranty. 0/07 Please read and keep these instructions. Indoor use only.
2 Index Parts Overview... Standard Accessories... Operation Instructions... Figure : Gear Axle... Figure : Initiative Axle... Figure : Fork... 7 Figure : Change Speed Axle... 8 Figure : Turning Plate and Mixing Axle... 9 Figure : Single Phase Motor Diagram... 0 Figure 7: Center Axle... Maintenance and Protection... Troubleshooting... Warranty Information...
3 Parts Overview Top cover Gear box Safety net(move) Inner gear Turning plate Mixing device I Bowl Stop ring Centre axle Fork Bearing 0 Key *0 Stop switch Change speed axle Nameplate Micro-switch Micro-switch shelves Screw Spring Handle Gasket Screw Arm Copper nut Big belt wheel Sleeve Board Gear box cover Gear axle Initiative axle Motor Stand Back board Gasket Small taper gear Flange knot Handwheel axle Key * Key * Handwheel Handle sleeve Handle axle AC contact device Seat Bar Back cover Capacitor Electric box Safety net(fixedly) Mixing device II Mixing device III Stop ring Big taper gear Thread bar Start switch Micro-switch shelves
4 Standard Accessories Item Flat Beater Dough Hook Wire Whip Bowl NOTES: Any agitator is easily installed by simply raising it onto the mixing axle, and the rotating it clockwise on the shaft until it locks into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate counterclockwise and lower. All of the accessories are precisely fitted to the bowl, have rounded corners, and are easily removed for cleaning. Operation Instructions! Please ensure that your power supply matches your machine NEMA 0P 0V! For changing the speed: Please stop machine first before changing speed in order to avoid damage to the gear box. Also make sure that the bowl is in fully lifted position and the guard is closed. Slow Speed is the middle, dough hook setting. The knob will be facing forward. Medium Speed is the bottom, flat beater setting. The knob will be straight down. High Speed is the top, whisk setting. The knob will be straight up. Mixing: Always use the correct attachment for the job. A. Wire Whip: Suitable for mixing liquids and soft ingredients, can work in all speeds. Do not run for more than minutes. B. Flat Beater: Suitable for mixing dry ingredients, can work in low & medium speeds only. Do not use in high speed. Do not run for more than minutes. C. Dough Hook: Suitable for mixing dough, can work in low & medium speeds only. Do not use in high speed, do not run for more than 0 minutes. Absorption ratio must be more than 0%. Refer to mixer capacity chart.
5 Mixer Capacity Chart Product Agitator and Speed Maximum Bowl Capacity 0 qt. Bread and Roll Dough -0 % AR Dough Hook - st only lbs. Heavy Bread Dough -% AR Dough Hook - st only lbs. Pizza Dough, Thin -0% AR Dough Hook - st only lbs. Pizza Dough, Medium -0% AR Dough Hook - st only lbs. Pizza Dough, Thick -0% AR Dough Hook - st only 0 lbs. Raised Donut Dough -% AR Dough Hook - st and nd lbs. Mashed Potatoes Flat Beater 8 lbs. Waffle or Hot Cake Batter Flat Beater 0 qts. Egg Whites Wire Whisk. qts. Whipped Cream Wire Whisk qts. Cake Batter Flat Beater lbs. When mixing dough ( pizza, bread or bagels), check your "AR" absorption ratio - water weight divided by flour weight. Above capacities based on % flour moisture at 70 F water temperature. If high gluten flour is used, reduce above dough batch size by 0%. Example: If recipe calls for lbs. of water and 0 lbs. of flour, then divided by 0 = 0.0 x 00 = 0 %AR. nd Speed should never be used on mixtures with less than 0% AR. Do not use attachments on hub while mixing. When calculating the correct size mixer for your application, here are some helpful weights & measures: 8. lbs. = gallon of water.08 lbs. = Quart.
6 GEAR AXLE Figure 7 Bearing 0 Gear axle Key *8 High-speed gear Sleeve Low-speed gear Gasket
7 INITIATIVE AXLE Figure Bearing 0 Initiative axle Key *8 Bearing 0 Gasket 7
8 FORK Figure Fork axle Fork Nut Spring Shaft 8
9 CHANGE SPEED AXLE Figure Handle knot Handle Screw M*0 Screw M* Speed block O ring.*.8 Spring Steel ball Stop ring 0*. O ring *. Change speed axle Eccentricity knot Pin * 9
10 TURNING PLATE AND MIXING AXLE Figure Inner gear Screw Nut M Spring gasket Gasket Planetary gear Bearing 0 Turning plate Spring gasket Nut Safe net Bearing 0 Oil seal ** Key * Mixing axle 9 Pin 0*
11 SINGLE PHASE MOTOR DIAGRAM Figure N PE L K K K K K0 KT C C K K K overload protection switch C C AC contact device The machine must be Kputbowl in the liftdry switch and flat ground, and make sure the machine steadily. We can use four screws K tosafety fix theprotect bracket, switch so the mixer will not shake or slope. K urgency stop switch Check the power voltage is suitable for voltage of this mixer or not before using, the ground wire is firm whether or not. K switch K reactor When the motor of this K0machine fluctuateis safety equipped switchwith 80V, you can ask the professional electricians to fix the electrical KT time relay source. If you find that running direction is not right, you M CA/CB capacitor can change the two wires, besides the ground wire. CB M motor CA Warning: users must install the shell ground wire. SPECIFICTION SPECIFICATIONS Type B0FA MX0 Capacitor Capacity (Qt) L 0 Power Supply (V) V 00-0~ 0 Input Power (W) W 00 Mixing Mixing Speed Speed (r.p.m.) r.p.m 0 Maxflour Max Capacity(kg) Flour Capacity (kg) 7 HP.
12 CENTER AXLE Figure Key 8*7*0 Bearing 0 Bearing ring Gear Gasket Oil seal 0**0 O ring 0*.8 Cover Roller Spring Engager Gear ring Dividing ring Gear Above bearing ring Joint Key 8*7* Key 8*7*0 Centre axle Bearing 0 Sleeve
13 Troubleshooting Trouble Possible Causes Solution The axles can t work when operating the machine Poor contact of the electrical equipment Check the Plug The mixing bowl is out of position Moving direction is not correct Change Leaks oil Sealing washer is damaged Change Difficult to move the bowl up and down Slideway is rusted Clean the slideway and lubricate The motor is overheated and speed is down The voltage is not enough, or incorrect speed Check the voltage or use lower speed Noise and overheating Poor lubrication Add or change lubrication Mixer touches bowl The mixing device or bowl deformed Repair or change the bowl or mixing device Limited Warranty All equipment, which is sold under Avantco trademark and used for commercial purpose is warranted against defects in materials and workmanship. The warranty runs for one year from the time of purchase and is for the benefit of the original purchaser only. All other Warranties, Expressed or Implied, Statutory or Otherwise, including Without Limitation any implied Warranty of Merchantability or Fitness for Purposes are excluded. The Seller shall in no event be liable for direct, indirect or consequential damages in connection with Avantco commercial products. This warranty is not effective if damage occurs because of accident, carelessness, improper installation, lack of proper set up, supervision when required or if the equipment is installed or operated in any manner contrary to the installation and operating instructions. In these cases, repairs will be made at a reasonable cost. Work performed by unauthorized personnel or unauthorized service agencies voids this Warranty. Items not covered under warranty: Changing Gears on the Mixers while Unit is Running and Overloading as Determined by an Approved Certified Technician. This warranty does not apply to, and Avantco is not responsible for any warranty claims on products sold or used outside of the contiguous United States. This equipment is intended for commercial use only. Warranty is void if equipment is installed in anything other than commercial applications.
User Manual. Gear Driven 40 Qt. Commercial Mixer. Models: MX40. Please read and keep these instructions. Indoor use only.
Gear Driven 0 Qt. Commercial Mixer Models: MX0 Shifting gears while this unit is running will void warranty. 0/07 Please read and keep these instructions. Indoor use only. www.avantcoequipment.com Index
More informationoperator s manual Commercial 7qt Deluxe Mixer
performance reliability simplicity operator s manual Commercial 7qt Deluxe Mixer Model No. Item No. Description HP SM7DX 7007 Commercial 7qt Deluxe Mixer ¾ t 800.469.8908 f 407.264.6309 mike@ 16-HBV-050
More informationSP8 SP10 SP20 SP25 SP30P SP40P SP60P SP80PL
mixing? Globe it. Globe mixers the perfect mix of performance, The Perfect Mix Whip up savings with Globe s family of heavy-duty mixers. Powerful custom-built motors, gear-driven transmissions, rugged
More informationTEDDY W5A OPERATING INSTRUCTIONS
TEDDY W5A US OPERATING INSTRUCTIONS EXPLODED VIEW No... Description... Part No. 1... Control button, l. and r.... AR005-178-TZ005 2... Base... AR005-022-TZ002 2.1... Fuse 5 A, slow, 110V... AR005-418-00001
More informationFOOD Mixer Operation Instruction
FOOD Mixer Operation Instruction General Description This is a kind of changing speed gear mixer. With its planetary stirring design, it has a compact structure, high efficiency, power saving and easy
More informationV5A TEDDY TEDDY is a registered trademark belonging to A/S Wodschow & Co. SPARE PART AND OPERATION MANUAL
V5A TEDDY TEDDY is a registered trademark belonging to A/S Wodschow & Co. 052017 US SPARE PART AND OPERATION MANUAL 14240 South Lakes Drive Charlotte, NC 28273 800 222-1138 www.varimixer.com mixer@varimixer.com
More informationPM 10 PARTS LIST 1 BEATER PM NUT PM HOOK PM SPRING PM WHIP PM PIN PM STEEL BUSHING PM10
PM 10 PARTS LIST 1 BEATER PM10-00001 68 NUT PM10-00068 2 HOOK PM10-00002 69 SPRING PM10-00069 3 WHIP PM10-00003 70 PIN PM10-00070 4 STEEL BUSHING PM10-00004 71 YOKE SHIFTER ROD PM10-00071 5 POWER HEAD
More informationCONTENTS MACHINE SPECIFICATION.. :.:. 1-1 MACHINE DESCRIPTION MACHINE COMMANDS. 1-2 CHAPTER 2 INSTALLATION, USE, MAINTENANCE 2-1
Via Artigianato 85 25030 Torbole Casaglia (BRESCIA) ITALY Tel. 0302650479 Fax 0302650143 INSTRUCTION BOOK PLANETARY MIXER BM20 CONTENTS CHAPTER 1 TECHNICAL SPECIFICATIONS 1-1 MACHINE SPECIFICATION.. :.:.
More informationMODEL TON HYDRAULIC FLOOR JACK
MODEL 66510 10 TON HYDRAULIC FLOOR JACK USER'S MANUAL *This hydraulic jack conforms to all "ANSI / ASME" safety standards. Jackco Transnational Inc. 2010 South El Monte, CA 888-452-2526 To see more jackco
More informationMODEL TON HYDRAULIC FLOOR JACK
MODEL 66500 5 TON HYDRAULIC FLOOR JACK USER'S MANUAL *This hydraulic jack conforms to all "ANSI / ASME" safety standards. Jackco Transnational Inc. 2010 South El Monte, CA 888-452-2526 To see more jackco
More informationHigh Quality Commercial Foodservice Equipment
High Quality Commercial Foodservice Equipment 03 07 11 13 MIXES SICES MEAT POCESSING VEGETABE & B CUTTES 15 17 General Food Equipment With a name you have known and trusted since 1955 Features a variety
More informationGLOBE MIXER MODEL SP-25
S6161-1K-FSE-010 0910-LP-113-0781 INSTRUCTION MANUAL FOR GLOBE MIXER MODEL SP-25 N00024-11-C-2111 GLOBE FOOD EQUIPMENT COMPANY 2153 DRYDEN RD. DAYTON, OH 45439 DISTRIBUTION STATEMENT B: DISTRIBUTION AUTHORIZED
More informationSPARE PART AND OPERATION MANUAL FOOD MIXER Model W20D
SPARE PART AND OPERATION MANUAL FOOD MIXER Model W20D Caution -READ BEFORE OPERATING- Caution Varimixer recommends that mixer operators be at least 18 years of age and be thoroughly trained on the use
More informationOwner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Hand Pallet Trucks Model SS45
Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Hand Pallet Trucks Model SS45 This publication, 1188027A, applies to the Lift-Rite Hand Pallet Truck, Model SS45 and
More informationBenron Equipment & supply, Inc.
Benron Equipment & supply, Inc. Service Manual G5 Part Number 6-00A. and 6-00M Edition 0/008 Ez-Tex G5 Operational Instructions. Before attempting to use the G5 check material manufacturer for mixing and
More informationHydraulic Clutch Jack
Hydraulic Clutch Jack Operating Instructions & Parts Manual Model Number Atd-7404 Capacity 500 Lb. Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China ATD7404-M0 05/07 Save these
More informationFOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL: SERIAL NUMBER: DATE PURCHASED: PURCHASED FROM:
FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL: SERIAL NUMBER: DATE PURCHASED: PURCHASED FROM: BASIC TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine does not work Power switch
More informationSMF01BLUS New product
SMF01BLUS New product 50's Retro style Stand Mixer Black EAN13: 8017709197018 As awarded by The Chicago Athenaeum: Museum of Architecture and Design Aesthetic Die cast aluminum body Zinc alloy base with
More information1016 SERIES INSTALLATION, OPERATION, MAINTENANCE & PARTS
LIMITED WARRANTY CHEVRON, INC., ("Chevron"), warrants to the original purchaser that each new Chevron product will be free from defects in material and workmanship for a period of twelve (12) months from
More informationRead this entire manual before operation begins.
Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............
More informationParts Manual Vermeer/ McLaughlin Mud System 230P
2006 Perimeter Road. Greenville, SC 29605 Toll Free: 800/435-9340 - Phone: 864/277-5870 Fax: 864/235-9661 - Website address: www.mightymole.com Email address: mmole@mightymole.com Parts Manual Vermeer/
More informationSPECIFICATIONS CONTENTS:
Model 3052A 1,100 Lbs Air Assist 2 Stage Transmission Jack INSTRUCTION MANUAL CONTENTS: Page 1 Specifications Page 2 Warning Information Page 3 Assembly Page 4 Operating Instructions Page 4 Preventative
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS MODEL D300 SERIES MIXERS (INCLUDES MOTOR PARTS) ML-134258 ML-134261 D300T (Timed) D300C (Timed) PRIOR MLS COVERED IN THIS MANUAL ML-134211 ML-134213 ML-104421 ML-134114 D300T
More informationSPECIFICATIONS CONTENTS:
Model 3052 1,100 Lbs 2 Stage Transmission Jack INSTRUCTION MANUAL CONTENTS: Page 1 Specifications Page 2 Warning Information Page 3 Assembly Page 4 Operating Instructions Page 4 Preventative Maintenance
More informationOwner s Manual Hydro-X Xtreme Xtractor
4201 Lien Rd Madison, WI 53704 Owner s Manual Hydro-X Xtreme Xtractor Installation, Operation & Service Instructions Read and Save These Instructions The Phoenix Hydro-X Xtreme Xtractor is the most effective
More informationVERTICAL CUTTER FP-50 SPECIFICATIONS
VERTICAL CUTTER FP-50 Ideal to make bread crumbs, humus, mashed potato, vinaigrettes, meat paste, salmon pate, chopped nuts. Equipment can be used for mincing, chopping, pureeing, or whipping any products
More informationOwner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Hand Pallet Trucks Model PST Plus
Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Hand Pallet Trucks Model PST Plus This publication, 1269849/001B, applies to the Lift-Rite Hand Pallet Truck, Model
More informationRead this entire manual before operation begins.
Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS LEGACY MIXER HL120 HL200 HL200 HL200C ML-134296 ML-134289 ML-134331 ML-134312 PREVIOUS MLS COVERED IN THIS MANUAL HL200 ML-134308 A p r o d u c t o f H O B A R T 7 0 1 S. R
More informationParts Manual Vermeer/ McLaughlin Mud System 230P
2006 Perimeter Road. Greenville, SC 29605 Toll Free: 800/435-9340 - Phone: 864/277-5870 Fax: 864/235-9661 - Website address: www.mightymole.com Email address: mmole@mightymole.com Parts Manual Vermeer/
More informationInstallation & Operation Manual Chef Base
Installation & Operation Manual Chef Base Please read this manual completely before installing or operating this unit! BACB53 BACB53M BACB71 BACB71M BACB74 BACB74M BACB83 BACB83M BACB86 BACB86M BACB96
More informationOwner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Titan Series Hand Pallet Trucks Model LCF55 - Freezer Special
Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Titan Series Hand Pallet Trucks Model LCF55 - Freezer Special Lift-Rite, 5975 Falbourne Street, Mississauga, Ontario
More informationCRD610 Automatic Fitting Inserter
CRD610 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 1.2 LAST EDITED 12.12.2018 cleanroomdevices.com 1 Table of Contents Title Page. 1 Table of Contents...2 1.0 General Product & Safety Information....3
More informationPower Controller IMPORTANT INFORMATION. What s In the Box? Assembly, Operation, & Maintenance
Power Controller Assembly, Operation, & Maintenance Congratulations on your purchase, and thank you for selecting the Power Controller from Blichmann Engineering. We are confident that it will provide
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS LEGACY MIXER HL120 HL200 HL200C HL200 HL200 ML-134459 ML-134455 ML-134456 ML-134457 ML-134458 A product of HOBART 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 43177 (May
More informationMODEL VG08001 CONTENT PACKING LIST / TOOLS NEEDED PANEL DIMENSIONS FITTINGS / TECHNICAL DATA WALL/CORNER INSTALLATION CARE AND TROUBLE SHOOTING
CONTENT PACKING LIST / TOOLS NEEDED PANEL DIMENSIONS FITTINGS / TECHNICAL DATA WALL/CORNER INSTALLATION CARE AND TROUBLE SHOOTING WARRANTY 1 PACKING LIST DESCRIPTION MODEL NUMBER - PANEL HOUSING 88057
More informationFUNNEL CAKE FRYER Instruction Manual Models: 8078 / FC-4, 8082 / FC-6, and 8090 / FC-4
Part No. 89784 Revised: December 2005 FUNNEL CAKE FRYER Instruction Manual Models: 8078 / FC-4, 8082 / FC-6, and 8090 / FC-4 Cincinnati, OH 45241-4807 USA GAS SAFETY PRECAUTIONS INSTALLATION INSTRUCTIONS
More informationUSER MANUAL. NEMA 48C Flange Mounted, Enclosed, Clutch Brake. FMCBE Model 500 FORM NO. L A (i)
USER MANUAL NEMA 48C Flange Mounted, Enclosed, Clutch Brake FMCBE Model 500 (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual
More informationAir Compressor. Owner s Manual
35 WARNING! READ AND UNDERSTAND ALL SAFETY PRECAUTIONS IN THIS MANUAL BEFORE OPERATING. FAILURE TO COMPLY WITH INSTRUCTIONS IN THIS MANUAL COULD RESULT IN PERSONAL INJURY, PROPERTY DAMAGE, AND/ OR VOIDING
More informationBlue Air. Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases
Blue Air Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases Please read this manual completely before installing or operating this unit! BACB53 BACB71 BACB74 BACB83 BACB86 BACB96
More informationOperating Instructions and Parts Manual Long Chassis Service Jacks
Operating Instructions and Parts Manual Long Chassis Service Jacks Models JSJ-3T/JSJ-5T/JSJ-10T WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-454430 Ph.: 800-274-6848 Revision A 8/05
More informationRTH2610B/RT3210HV DRIVE AXLE PARTS CATALOGUE
RTH2610B/RT3210HV DRIVE AXLE PARTS CATALOGUE IMPORTANT INFORMATION AFTERMARKET PARTS WARRANTY We warrant all new parts for one year from date of shipment to the buyer against defective material or workmanship
More informationOwner s Manual, Operating Instructions Manual, and Replacement Parts Manual
Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Titan Series Hand Pallet Trucks Models LCR55 and LCS55 Versions This publication, 1130442C, applies to the Lift-Rite
More information"WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD200SS TUBE EXPANDER OPERATIONS MANUAL VERSION 4.3 LAST EDITED 06.17.15 cleanroomdevices.com Table of Contents Table of Contents....1
More informationINSTRUCTION MANUAL FOR SINMAG SPIRAL MIXERS SM/KM-25/50/80T
INSTRUCTION MANUAL FOR SINMAG SPIRAL MIXERS SM/KM-25/50/80T Index. General information: Page 1 Components of package: Page 2 Movement and transportation: Page 3 Useful information: Page 4 Installation:
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS LEGACY MIXER HL120 HL120 HL200 HL200 HL200 HL200 HL200 HL200C ML-134296 ML-134459 ML-134289 ML-134331 ML-134455 ML-134457 ML-134458 ML-134456 A product of HOBART 701 S. RIDGE
More informationTS Series. MultiStage Centrifugal Pump Instruction Manual. Walrus America Inc. ISO 9001 Certified
TS Series MultiStage Centrifugal Pump Instruction Manual 234867 ISO 9001 Certified Walrus America Inc EC Declaration of Conformity Manufacturer: Walrus Pump Co., Ltd. Address: No. 83-14, Dapiantou, Sanjhih
More informationMini Manual Tire Changer
Mini Manual Tire Changer Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationGERINGHOFF. Corn Header Manual f HEADSIGHT.COM
GERINGHOFF Corn Header Manual 09020701f HEADSIGHT.COM 574.546.5022 About Headsight Headsight Contact Info Headsight, Inc. 4845 3B Road Bremen, IN 46506 Phone: 574-546-5022 Fax: 574-546-5760 Email: info@headsight.com
More informationHigh Quality Commercial Foodservice Equipment
113017 High Quality Commercial Foodservice Equipment MIXES SLICES MEAT POCESSING SLICES & CUTTES COFFEE & HOT WATE HEATING & COOKING 2-3 4-5 6-7 MIXES SLICES MEAT POCESSING General Food Equipment With
More informationMODEL 7400 STRUT SPRING COMPRESSOR
MODEL 7400 STRUT SPRING COMPRESSOR Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV112712 P/N: 81-0103A TABLE OF
More informationSEMI-AUTOMATIC MEAT SLICER
MS-10 SEMI-AUTOMATIC MEAT SLICER This manual contains important information regarding your Supera unit. Please read this manual thoroughly prior to equipment set-up, operation and maintenance. Failure
More informationOperating Instructions and Parts Manual SLT-330F Scissor Lift Table
Operating Instructions and Parts Manual SLT-330F Scissor Lift Table For serial no. 17020001 and higher JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-140771 Ph.: 800-274-6848 Revision C
More informationRead this entire manual before operation begins.
Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............
More informationMODEL G300 BRAKE BLEEDER
MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV120716 P/N: 81-0035H THIS PAGE INTENTIONALLY
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS HL120/200 SERIES LEGACY MIXERS ML-134296 ML-134459 ML-141092 ML-134289 ML-134331 ML-134455 ML-134456 ML-134457 ML-134458 ML-141094 ML-141095 ML-141108 HL120 HL120 HL120 (Canada)
More informationHydraulic Truck Jack
Operating Instructions & Parts Manual Hydraulic Truck Jack Model Capacity 23221C 22 Ton 23222C (Low Profile) 22 Ton 23301 30 Ton Models 23221C & 23222C Model 23301! U.S. Patent No's. 5,341,723 & 5,94,912
More informationOwner s Manual. 10U Wall-Mounted SmartRack Enclosure. Model: SRW10US W. 35th Street, Chicago, IL USA
WARRANTY REGISTRATION Register online today for a chance to win a FREE Tripp Lite product www.tripplite.com/warranty Owner s Manual 10U Wall-Mounted SmartRack Enclosure Model: SRW10US Table of Contents
More informationOwner s Manual, Operating Instructions Manual, and Replacement Parts Manual
Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Titan Series Hand Pallet Trucks Models LCM50, LCU50, and Four-Way Versions This publication, 114374C, applies to the
More information1250 LB. CAPACITY MECHANICAL WHEEL DOLLY
1250 LB. CAPACITY MECHANICAL WHEEL DOLLY 67287 SET-UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result
More informationASSEMBLY STEP ONE STEP TWO STEP THREE STEP FOUR STEP FIVE
ASSEMBLY STEP ONE Attach the front [18] and rear feet [14] to the frame using the nuts [8], washer [9] and bolts [10]. STEP TWO STEP THREE STEP FOUR STEP FIVE Attach the handlebar post [22] inserting into
More informationMini Jacks Instruction Manual
J11050-M0_062017 Instruction Manual MODELS: J11050, J11055-5 Ton Capacity J11100-10 Ton Capacity J11200-20 Ton Capacity This is the safety alert symbol. It is used to alert you to potential personal injury
More informationForce Test Stands Series TS MODELS TSA750, TSA750H, TSB100, TSC1000 & TSC1000H. User s Guide
Force Test Stands Series TS MODELS TSA750, TSA750H, TSB100, TSC1000 & TSC1000H User s Guide Series TS Force Measurement Test Stands Thanks! Thank you for purchasing a Mark-10 Series TS Force Measurement
More information2000-lb Hand Winch Truck Crane
2000-lb Hand Winch Truck Crane Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationOperating Instructions and Parts Manual AHR-50 Auto Rewind Hose Reel
Operating Instructions and Parts Manual AHR-50 Auto Rewind Hose Reel JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-426238 Ph.: 800-274-6848 Revision C 04/2017 www.jettools.com Copyright
More informationParts Catalog. Mixer SP30. Model:
, 0 99 ECN Parts Catalog Mixer SP0 Model: SP0 0/9/0 Rev. - IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT. GLOBE FOOD EQUIPMENT COMPANY East
More informationTABLE OF CONTENTS. Warranty Disclaimers Delivery Checklist After Sale Checklist Safety Set Up... 8
TABLE OF CONTENTS Pickett Equipment Warranty... 2 Warranty Disclaimers... 3 Delivery Checklist... 4 After Sale Checklist... 4 Safety... 5-7 Set Up... 8 Machine Adjustments and Operation... 9 Maintenance
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: CL-36-BDF-A, CL-42-BDF-A, CL-48-BDF-A E355088 READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the instructions in this manual
More information3000-Lb. Vehicle Positioning Jacks. Owner s Manual
3000-Lb. Vehicle Positioning Jacks Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationLow Profile Service Jack
Low Profile Service Jack Operating Instructions & Parts Manual Model Number JSA200LCX Capacity 2 Ton MAC TOOLS INC. 2005 505 N. Cleveland Ave. Suite 200 Westerville, OH 43082 Printed in PRC Save these
More informationPreassembled Clutch/Brake Module
Preassembled Clutch/Brake Module P-273-1-WE 819-0343 Installation Instructions An Altra Industrial Motion Company Contents MountingtoaMotor...3 Mounting to a Reducer.............3 Installing the Base Mount...........4
More informationMIXER ACCESSORIES AND ATTACHMENTS
SERVING THE FOOD INDUSTRY SINCE 1951 GRINDER HEAD ATTACHMENT FOR MIXERS With available units compatible for #12 and #22 drive hubs. Complete with a cast iron worm, ring, and cylinder, this grinder head
More informationCLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.1 LAST EDITED 7.25.14 DOCUMENT NUMBER 001 cleanroomdevices.com 1 Table of
More informationOPERATIONS MANUAL LEVER CHAIN HOIST
OPERATIONS MANUAL LEVER CHAIN HOIST IMPORTANT SAFETY INFORMATION Please read, understand and follow all safety information contained in these instructions prior to the use of this hoist. Retain these instructions
More information24G621 Agitator Speed Controller Accessory
Instructions-Parts 24G62 Agitator Speed Controller Accessory 3A35A ENG Accessory kit to control and automatically maintain the speed of an air-powered agitator. For professional use only. Important Safety
More informationOwner s (Operator s) Manual & Safety Instructions Manually Lever Operated Chain Hoist Model LX1B
Owner s (Operator s) Manual & Safety Instructions Manually Lever Operated Chain Hoist Model LX1B BULLETIN NO. LX-0804-CE-06 WARNING This equipment must not be installed, operated or maintained by any person
More informationOwner s Manual Hydro-X Xtreme Xtractor
4201 Lien Rd Madison, WI 53704 Owner s Manual Hydro-X Xtreme Xtractor Installation, Operation & Service Instructions Read and Save These Instructions The Phoenix Hydro-X Xtreme Xtractor is the most effective
More informationCompressor Clutch Replacement Procedure
Clutch Replacement Procedure P-1401-WE 819-0316 Installation Instructions An Altra Industrial Motion Company Warner Replacement Clutches for the following compressors: Denso 6E171 10P15 6P148 6C17 Ford
More informationOperator s Manual. Nitro 1000 Nitro 1000X. Nitro 750 Nitro 750X. September REV0
Operator s Manual Nitro 750 Nitro 750X Nitro 1000 Nitro 1000X September.27.2018REV0 Table of Contents Introduction...3 Safety.....4 Equipment Requirements......5 What You Have Received. 5 Serial Number...6
More informationPACKING LIST DESCRIPTION MODEL NUMBER - PANEL HOUSING HAND SHOWER HOSE HAND SHOWER FLEXIBLE HOSES 16" LONG WITH 1/2" FEMALE 88
MODEL VG-08009 CONTENT PACKING LIST / TOOLS NEEDED PANEL DIMENSIONS FITTINGS / TECHNICAL DATA WALL/CORNER INSTALLATION CARE AND TROUBLE SHOOTING WARRANTY 1 PACKING LIST DESCRIPTION MODEL NUMBER - PANEL
More informationHydraulic Transmission Jacks
Hydraulic Transmission Jacks Operating Instructions & Parts Manual Model Number Atd-7435 Atd-7436 Atd-7437 Capacity 1100 Lb. 2000 Lb. 3000 Lb. Model Atd-7435 Model Atd-7436 Model Atd-7437 Atd Tools Inc.
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS HL400 LEGACY MIXER HL400 HL400C ML-134348 ML-134359 A product of HOBART 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 43137 (June 2007) - 2 - HOBART Table Of Contents 5 CONTROL
More informationRENEGADE MODEL 408V&T
OWNER'S MANUAL RENEGADE MODEL 08V&T INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice. All ratings specified are based on structural factors
More informationTALCO FIRE SYSTEMS. LSF Start-Up Instructions. 1) IMPORTANT: Inspect the unit for damage. Report any damage to the freight carrier immediately.
LSF Start-Up Instructions 1) IMPORTANT: Inspect the unit for damage. Report any damage to the freight carrier immediately. 2) PRE-START-UP: Be sure there is water in the pump. Bleed air at all high points
More informationDeZURIK AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators
AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators Instructions D11033 August 2013 Instructions These instructions provide information about AFR3 Filter Regulators. They are for use by personnel
More informationExtension Hopper Installation & Operator s Instruction Manual for Model 55, 75, 90, & HMC FLEX-AUGER Feed Delivery Systems
Extension Hopper Installation & Operator s Instruction Manual for Model 55, 75, 90, & HMC FLEX-AUGER Feed Delivery Systems April 02 Chore-Time Warranty Chore-Time Equipment warrants each new product manufactured
More informationMODEL 7600 STRUT SPRING COMPRESSOR
MODEL 7600 STRUT SPRING COMPRESSOR Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV6162014 P/N: 81-0246 TABLE OF
More informationRead this entire manual before operation begins.
Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............
More information1014 SERIES INSTALLATION, OPERATION, MAINTENANCE & PARTS
OWNER'S MANUAL 1014 SERIES INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice. All ratings specified are based on structural factors only,
More informationSERIES 30 INSTALLATION, OPERATION, MAINTENANCE & PARTS
OWNER'S MANUAL SERIES 30 INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice. All ratings specified are based on structural factors only,
More information210, 220, 230 and 240 Series 2 Speed Single Axles Catalog PB-92126
Revised 11/02 210, 220, 230 and 240 Series 2 Speed Single Axles Catalog PB-92126 Strength Power Speed Agility MERITOR PARTS. RIGHT FROM THE START. HOW TO USE THIS CATALOG There are four basic carriers
More informationOperating Instructions for PAC800 Battery Charger
Operating Instructions for PAC800 Battery Charger General Safety The charger may only be used for the specified battery types. This battery charger is supplied with pre-set charging curves that are adapted
More informationOperations Manual. Model: DPR3000 Dual Pass Dough Sheeter. proluxe.com. formerly DOUGHPRO. New Name. Same Quality. Superior Service.
Operations Manual Model: DPR3000 Dual Pass Dough Sheeter formerly DOUGHPRO. New Name. Same Quality. Superior Service. proluxe.com Dough Roller (double pass) Heavy duty stainless steel construction. Compact
More informationSHEYENNE TELE-BOOM OWNERS MANUAL OPERATOR INSTRUCTIONS PARTS BOOK
SHEYENNE TELE-BOOM OWNERS MANUAL OPERATOR INSTRUCTIONS PARTS BOOK 701 Lenham Ave. SW PO Box 647 Cooperstown ND 58425 1-800-797-1883 701-797-2700 * 701-797-2584 Fax www.sheyennemfg.com TABLE OF CONTENTS
More informationRead this entire manual before operation begins.
Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............
More informationInstallation Manual. D3600- Series Duplex Grinder Systems. Contents
Installation Manual 7353000E D3600- Series Duplex Grinder Systems Features: 36 Diameter Fiberglass Tank Available in 48, 60, 72, 84, and 96 heights LSG Single or LSGX 2 Stage 2HP Grinder Pumps Factory
More informationOperator s Manual DROP-IN FROST TOP ENGLISH
ENGLISH DROP-IN FROST TOP Item Description HP Voltage Amps Plug 36419 Two-pan 1/4 hp 120V 4.9 5-15P 36420 Three-pan 1/3 hp 120V 5.9 5-15P 36424 Four-pan 1/3 hp 120V 5.9 5-15P 36426 Five-pan 1/2 hp 120V
More informationRTH2610B/RT3210HV DRIVE AXLE PARTS CATALOGUE
RTH2610B/RT3210HV DRIVE AXLE PARTS CATALOGUE IMPORTANT INFORMATION AFTERMARKET PARTS WARRANTY We warrant all new parts for one year from date of shipment to the buyer against defective material or workmanship
More informationCLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600AF Automatic Fitting Inserter With Auto Feed OPERATIONS MANUAL (Shown with optional alcohol dispenser) 1 VERSION 1.1 LAST EDITED
More informationIMPORTANT SAFETY INFORMATION
Specifications Tricycle Height 26 Front Wheel 5/8 Axle Diameter, 13 Pneumatic Knobby Tire Back Wheels 5/8 Axle Diameter, 10 Pneumatic Knobby Tire Age Range 5 and up Weight Capacity 150 lb. IMPORTANT SAFETY
More information