ISSPRO ATTRIBUTE PROGRAMMER
|
|
- Gwendoline Ball
- 6 years ago
- Views:
Transcription
1 ISSPRO, INC N.E. Riverside Way, Portland OR Telephone: (503) Toll Free: (800) Fax: (503) ISSPRO ATTRIBUTE PROGRAMMER Please read the Attribute Programmer Installation Guide in the CD before proceeding with the installation. Form No. IS204 (07/15/2016 Rev. H) Page 1 of 7
2 ISSPRO, INC N.E. Riverside Way, Portland OR Telephone: (503) Toll Free: (800) Fax: (503) ISSPRO Attribute Programmer Instructions The Attribute Programmer is used to activate and set levels for warning lights & outputs, adjust lighting curves, and adjust filtering characteristics of ISSPRO EV² and Performax electronic gauges. 1) Install the programming software onto your PC: Insert the CD into a CD drive on your PC, if it does not autostart then follow steps a and b, if it does autostart then proceed to step c: a) Using Windows Explorer to select the CD drive (as an example, if it were the D: drive, double click on the D: in Windows Explorer). b) Double click on the file setup.cmd or setup.exe. Please note that the.cmd or.exe extension may not be visible depending on preferences selected on your PC. Follow direction on your screen to proceed with the installation. c) It is recommended that you keep the default destination values. d) Once program has completely installed, click Finish button. Form No. IS204 (07/15/2016 Rev. H) Page 2 of 7
3 ISSPRO, INC N.E. Riverside Way, Portland OR Telephone: (503) Toll Free: (800) Fax: (503) e) Creating a desktop shortcut: i) Click Start, point to All Programs, point to Attribute Programmer folder, and then point to Attribute Programmer. ii) Right-click the Attribute Programmer file, point to Send To, and then click Desktop (creating shortcut). iii) Attribute Programmer shortcut appears on your desktop. 2) Connect the programming cable to the gauge: a) EV²: i) Expose the programming pins on the back of the gauge: 1) Using small wire cutters or something similar cut the sides of the breakaway portion below the opening for the electrical connector. 2) Bend the remaining tab back to allow access to the programming pins. You can also break the tab completely out if desired. ii) Plug the connector of the USB cable into the back of the gauge, with the red wire towards the left side of the gauge back as it is facing you (closest to pin #6 on the gauge). b) Performax and Sealed EV2: i) Plug one end of the short cable with orange connector into the programming module, with the angled barbs on the connector facing towards the white tab on the module. Plug the other end of the same cable into the back of the gauge: Performax Sealed EV2 ii) Connect the power supply cable to the center jack on the module, then plug the end of the USB programming cable into the module, with the green wire closest to the indicator Form No. IS204 (07/15/2016 Rev. H) Page 3 of 7
4 LED (towards the right as you are looking at that end of the module). Plug the power supply into a household outlet: 3) Plug the USB end of the cable into the PC s USB port. The first time using the programmer there will be a delay while Windows installs the driver. Note that the drivers are on the installation CD. The CD must be installed when first using the USB port. 4) Start the program by double-clicking its icon. 5) 4743 Program Attributes window will display. 6) Under Gauge Type, select the gauge type you are working with. Within EV2 choices the differences are in the default programming for the Dimmer Max and Dimmer Min values, to match the factory backlighting for the particular truck. See also notes A & B on last page. 7) Under Description, select the specific gauge you are working with, such as Turbo Boost 100 psi. Once you make this selection then the default values for this gauge will show in the adjustment windows. 8) Sealed/Unsealed switch - EV2 only, select whether gauges are sealed or standard (unsealed). 9) Dimmer/Backlight EV2 only, these are the values for dimmer circuit input to the gauge at Form No. IS204 (07/15/2016 Rev. H) Page 4 of 7
5 the maximum and minimum light output conditions. Note that the max values are typically higher than actual vehicle voltages, which is necessary to match the factory backlight levels. These values may be adjusted to get the gauge brightness to perfectly match the factory dash at various brightness levels, but otherwise should be left at default values. To adjust the values, set the Dimmer Min to match the voltage of the dimmer circuit when the factory dash turns off or is at a minimum. If the gauges are too bright with the dimmer adjusted at maximum then set the Dimmer Max value higher than its default value. The Dimmer Max may be set as high as 25.5V on gauges prior to D323, and may be set as high as 102V on gauges after D323. If the Dimmer Max is set higher than 25.5V on gauges earlier than D323, the gauge will not program properly. 10) Alarm Lamp Output Direction toggle switch to define if the warning light comes on above a maximum level or below a minimum level. Maximum level values are used for pyrometers and most other gauges, but minimum levels are frequently used for Oil Pressure and Fuel Pressure. 11) Alarm Lamp Warning Level the set point at which the alarm turns on. This may be set by rotating the knob with the mouse pointer, or clicking in the window below the knob and typing in an exact number. 12) Output Module Warning Level Same functionality as Alarm Lamp adjustments but for switching points on optional output module (P/N R82006). Only used with gauges S/N F19 and later, with earlier S/N gauges the output direction switch must be selected down in the Output turns ON when Pointer goes LOW position to prevent improper gauge operation. NOTE: When used with pressure gauges and a high level warning (switching the module as the pressure rises), if the pressure rises slowly, rapid on-off switching of the module may occur as it passes the programmed level. a) 15 Sec Delay at Startup only used on gauges S/N F288 and later. Set this switch high to ignore the Output Module activation point for the first 15 seconds of gauge operation. Useful for applications such as switching based on oil pressure or fuel pressure which is low at start. b) Delay (sec) on Activation - only used on gauges S/N F288 and later. Selects a minimum period of time which the Output Module activation condition must be present before the module is activated. 13) Test Mode EV2 only, used to confirm the alarm and output module value and direction settings: a) After selecting your values for the alarm level and direction, make sure the switch for Test Mode is up, and then press the Program Part button. It will change color briefly then return to the original color. b) Sealed only: a. A few seconds after programming the gauge should begin cycling through its full range of values, with the warning light turning on at the selected point. b. If the gauge is NOT working as intended, check/reset the value in question, and repeat step 13a. c. If the gauge IS working as intended, click the Test Mode switch to the down position to Normal Mode, then click on the Program Part button. d. Unplug the programmer connector from the gauge, reinstall gauge in the vehicle, and confirm correct gauge functionality. Form No. IS204 (07/15/2016 Rev. H) Page 5 of 7
6 c) Unsealed only: a. Unplug the programmer connector from the gauge, then plug the vehicle s orange gauge harness connector back into the gauge and turn on power. The gauge should begin cycling through its full range of values, with the warning light turning on and the output module switching at the selected points. b. If the gauge is NOT working as intended, unplug the gauge from the vehicle, plug the programmer connector back in to the gauge, check/reset the value in question, and repeat step 13a. c. If the gauge IS working as intended, unplug the gauge from the vehicle, plug the programmer connector back in to the gauge, click the Test Mode switch to the down position to Normal Mode, then click on the Program Part button. d. Unplug the programmer connector from the gauge, reinstall gauge in the vehicle, and confirm correct gauge functionality. 14) Pointer Position Performax only, used to confirm the alarm value and direction setting. After selecting your values for the alarm level and direction, press the Program Part button then simply move the rotary knob or enter a specific value in the box below the knob, the gauge will move to that value and the warning light should illuminate per its programming. 15) Reset to Default Values press this button if you would like to set all parameters to default, then follow steps 12a-12d. 16) Advanced this switch reveals advanced programming functions. Note: Some setting may affect the operation and/ or accuracy of the gauge. Use the new settings cautiously. If in doubt, the factory settings can be restored by pressing the Reset to Default Values button. a) Degrees Sweep Angular degrees of sweep between min and max positions on the gauge. b) Sensor Scan Rate the period in milliseconds for each cycle of scanning the sensor. Set to 250 for most gauges, or 100 for certain fuel pressure gauges. c) Hysteresis a setting of 0-255, defining the minimum change in the measured value necessary for movement of the pointer. A higher value will cause the pointer to remain steadier with small oscillations in values, but it will move more when it does finally move. d) Weight 0.01 to 1.0, with lower numbers giving more filtering to the pointer (i.e., slower but smoother response). 17) Stop button press this button at any time to stop programming. Form No. IS204 (07/15/2016 Rev. H) Page 6 of 7
7 Advanced Adjustments screen Note A: Certain older EV2 gauges (S/N earlier than B333, which would not have the warning light preinstalled) will not accept any programming using this software. Gauges with S/N B334 through C90 will work with this software but do not have warning lights. If you have an older gauge without warning lights and would like to use this software, or to make any other adjustments, you can return the gauge to ISSPRO for a nominal fee for an upgrade. To check if a gauge has a preinstalled warning light, simply watch the bottom of the face dial (6 o clock position) when powering up the gauge, if the warning LED is installed it will briefly light up red during start-up. Note B: Application of Output Module only available in EV2 gauges S/N F19 and later. S/N F288 and later necessary for Output Module Activation and Startup Delays, and use with wide pointers on R30000 and R32000 series EV2 gauges. Wide pointers require selecting 4 th Gen Dodge or Jetta gauge type. Form No. IS204 (07/15/2016 Rev. H) Page 7 of 7
MSD Programmable Shift Controller PN 75591
MSD Programmable Shift Controller PN 75591 WARNING: During installation, disconnect the battery cables. When disconnecting, always remove the Negative cable first and install it last. Parts Included: 1
More informationNEXUS. Introduction SENSOR MODULE &
2650-1056 INSTALLA AT TION INSTRUCTIONS NEXUS SENSOR MODULE & REMOTE ASSEMBLY IMPORTANT WEAR SAFETY GLASSES 60 80 40 100 FUEL 20 PSI 0 AUTO METER PRODUCTS INC. c 2004-6463 0 10 20 10 20 BOOST VAC In.Hg
More informationProgramming Instructions for : Pressure 2 1/16 + DOWN MODE UP. Spek Pro Fuel Rail Pressure Gauge
Programming Instructions for : Pressure 2 1/16 Spek Pro Fuel Rail Pressure Gauge Refer to the Flow Chart Programming Instructions while reviewing this guide. Gauge is field programmable by the operator
More informationGENERAL The AuRACLE Engine Management System primary display provides a graphical representation of the following engine instrumentation:
GENERAL The AuRACLE Engine Management System primary display provides a graphical representation of the following engine instrumentation: o Manifold Pressure (MAP) o RPM o Fuel Flow (FF) o Turbine Inlet
More informationCOMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT J
COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT J05306 2015-04-24 GENERAL Figure 1. Title 49, United States Code GENERAL (Continued) Table 1. Speedometer Features Available MODELS FEATURES GEAR INDICATOR
More informationSteering Angle Sensor (SAS) Replacement on Vehicles Equipped with Electronic Stability Control (ESC)
Revised 09-18 Technical Bulletin Steering Angle Sensor (SAS) Replacement on Vehicles Equipped with Electronic Stability Control (ESC) Revised 1 Technical 09-18 Bulletin Hazard Alert Messages Read and observe
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2008-2014 Honda CBR1000RR Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab 1 O2 Optimizer THE IGNITION MUST BE TURNED
More informationCurveMaker HD v1.0 2Ki Programmable Ignition programming software
Contents CurveMaker HD v1.0 2Ki Programmable Ignition programming software Dynatek 164 S. Valencia St. Glendora, CA 91741 phone (626)963-1669 fax (626)963-7399 page 1) Installation 1 2) Overview 1 3) Programming
More informationFUEL MOTO MICRO EFI TUNER HARLEY-DAVIDSON V-ROD MODELS. 1 Micro Tuner Module 1 USB Cable 1 CD-ROM 1 Installation Guide 1 Zip-tie
FUEL MOTO MICRO EFI TUNER INSTALLATION INSTRUCTIONS 2002-2011 HARLEY-DAVIDSON V-ROD MODELS PARTS LIST 1 Micro Tuner Module 1 USB Cable 1 CD-ROM 1 Installation Guide 1 Zip-tie 2 Velcro 1 Alcohol swab 1
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2008-2011 Yamaha TMax 500 Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2013-2014 Honda CBR600RR Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab 1 O2 Optimizer THE IGNITION MUST BE TURNED OFF
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2004-2007 Honda CBR1000RR Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!
More informationWater/Methanol Failsafe
Installation Instructions for P/N 30-3020 Water/Methanol Failsafe (Injection Monitor) WATER/METHANOL FAILSAFE PARTS LIST Qty P/N Qty P/N 1 35-3020 W/M Failsafe Gauge 1 35-8553W Faceplate 1000 White 1 35-2126
More informationFEATURES: SPEK PERFORMANCE GAUGE FEATURES:
Wiring Installation Instructions for : Pressure Gauge 2 1/16 Spek Pro Professional Racing Gauge SPEK PRO URE GAUGE PACKAGE CONTAINS: Pressure Gauge Pressure Sender Wiring Harness Mounting Cup (1) Neoprene
More informationINSTALLATION MANUAL SPECTRUM BRAKE CONTROL
INSTALLATION MANUAL 51170 SPECTRUM BRAKE CONTROL TABLE OF CONTENTS Controls & Components Tools List Before You Begin Wiring Wiring Diagram Mounting the LED Display Rotary Knob Wiring the Plug Connector
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
DYNOJET FUEL CONTROLLER PARTS LIST 1 Dynojet Fuel Controller 1 USB Cable 1 CD-ROM 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab 2008-2010 Honda SH125i/SH150i Installation Instructions PLEASE
More informationFlow Chart Programming Instructions for : VOLTMETER 2 1/16
Flow Chart Programming Instructions for : VOLTMETER 2 1/16 Program Main Menu (Press one button at a time) START HERE Main Menu ONE NORMAL/DIAL BRIGHTNESS: Press the down or up button to adjust dial brightness.
More informationOWNERS MANUAL GPS RENTAL. All PowaKaddy electric trolleys have been awarded the Quiet Mark by the Noise Abatement Society
OWNERS MANUAL GPS RENTAL All PowaKaddy electric trolleys have been awarded the Quiet Mark by the Noise Abatement Society Thank you for purchasing the new PowaKaddy FW5s GPS Rental Cart. Please read these
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2009-2010 BV300 / Vespa 300GTS Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab THE IGNITION MUST BE TURNED OFF
More informationAURORA SERIES GAUGES FUEL GAUGE SUGGESTED TOOLS AND MATERIALS. 3 3 /8 in (85.7 mm) PARTS LIST
GAUGE INSTALLATION. Select mounting locations for the fuel gauge. 2. Cut a 2 /6 (52 mm) diameter hole for the gauge and test for proper fitmate. 3. Tighten the gauge with the enclosed Aurora Mounting Clamp
More informationFeature Description. Version History
TA2 Malfunction Indicator Lamp (MIL) and Engine Protection Document Number: FD-0007 Author: J. Goodloe Version: 03 Publish Date: 2016-03-18 Feature Description Version History Version Date Modified Sections
More informationNORMAL/DIAL BRIGHTNESS: Press the down or up button to adjust dial brightness. Press the center button to save and advance to PEAK PLAYBACK.
Flow Chart Programming Instructions for : VOLTMETER 2 1/16 Program Main Menu (Press one button at a time) START HERE Main Menu ONE NORMAL/DIAL BRIGHTNESS: Press the down or up button to adjust dial brightness.
More informationSystem III Wiring Information 54-12
System III Wiring Information 54-12 System Operation General Information Initial Power On Description of Revisions: This service bulletin is updated and replaces the version dated September 2002. This
More informationPackage Contents: Transferring Data to a PC
-------------------------------------------------------------------------------------------- P/N: 250-DS-UDXSR --------------------------------------------------------------------------------------------
More informationOverview of operation modes
Overview of operation modes There are three main operation modes available. Any of the modes can be selected at any time. The three main modes are: manual, automatic and mappable modes 1 to 4. The MapDCCD
More informationITCEMS950 Idle Timer Controller - Engine Monitor Shutdown Isuzu NPR 6.0L Gasoline Engine
Introduction An ISO 9001:2008 Registered Company ITCEMS950 Idle Timer Controller - Engine Monitor Shutdown 2014-2016 Isuzu NPR 6.0L Gasoline Engine Contact InterMotive for additional vehicle applications
More informationGENERAL MOTORS SERVICE PARTS OPERATION 6200 Grand Pointe Drive, Grand Blanc, MI 48439
LS IGNITION CONTROLLER 19355418 Ignition Control for Carbureted LS Series Engines (24x Crankshaft Index/1x Camshaft Index, 58x Crankshaft Index/4x Camshaft Index) Parts Included Quantity Ignition Controller
More informationQUICK START GUIDE 199R10546
QUICK START GUIDE 199R10546 1.0 Overview This contains detailed information on how to use Holley EFI software and perform tuning that is included within the software itself. Once you load the software,
More informationCurveMaker DFS v2.0 Dyna FS Ignition Programming Software
CurveMaker DFS v2.0 Dyna FS Ignition Programming Software Contents Dynatek 164 S. Valencia St. Glendora, CA 91741 phone (626)963-1669 fax (626)963-7399 page 1) Installation 1 2) Overview 1 3) Introduction
More informationSPEK PRO MONITOR AND CONTROL
Programming Instructions for : Temperature 2 1/16 Spek Pro Racing Gauge - NASCAR ECU Compatible SPEK PRO MONITOR AND CONTROL Refer to the Flow Chart Programming Instructions while reviewing this guide.
More informationWireless Tire Pressure and Temperature Monitoring System Instruction Manual Model #: TM-507 SCE 507 Commercial Cap Sensors with Monochrome Display
Wireless Tire Pressure and Temperature Monitoring System Instruction Manual Model #: TM-507 SCE 507 Commercial Cap Sensors with Monochrome Display Thank you for purchasing the TST Tire Pressure Monitoring
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
Introduction An ISO 9001:2015 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2019 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications The A-ITC620-A1 is an
More informationTranZformer 2 nd Gen Shift Kit Installation
TranZformer 2 nd Gen Shift Kit Installation For Firmware Version 2.0.0-061214 The TranZformer Shift Kit is an electronic shift enhancer for 2011-2014 Dodge Charger and Chrysler 300 vehicles. The TranZformer
More informationSUBJECT: EB e-stroke GEN 3 Post Install Functionality Test
Introduction: The following procedure is intended to test the e-stroke system functionality after installation. Following these steps will verify that the system is installed correctly and the vehicles
More informationSubaru L Turbo
Subaru 02-05 2.0L Turbo Getting Started Product Introduction Congratulations on the purchase of the new AccessPORT handheld programmer. The AccessPORT can: Reprogram the factory engine control unit (ECU)
More informationAdvanced Torque Products
Advanced Torque Products Torque Cart Operation Manual 1 Click It or Risk It How many times do you believe the average operator uses a click-style torque wrench over the course of a day? Every time a torque
More informationMSD Programmable Shift Controller PN 7559
MSD Programmable Shift Controller PN 7559 WARNING: During installation, disconnect the battery cables. When Disconnecting, always remove the Negative cable first and install it last. Parts Included: 1
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2018 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications Introduction The A-ITC620-A1 is an
More informationInstalling the EFILive LBZ / LMM DSP2 & DSP5 Custom Operating Systems
Installing the EFILive LBZ / LMM DSP2 & DSP5 Custom Operating Systems Ross Myers Installing the EFILive LBZ/LMM DSP2 & DSP5 Custom Operating Systems 2009 EFILive Limited All rights reserved First published
More informationMAX-FIRE AND E-FIRE ELECTRONIC DISTRIBUTORS
INSTALLATION INSTRUCTIONS MAX-FIRE AND E-FIRE ELECTRONIC DISTRIBUTORS NOTE: This product is applicable to pre-1966 California and pre-1968 federally certified passenger cars. It is also applicable to non-emission
More informationWireless Tire Pressure and Temperature Monitoring System Instruction Manual Model #: TM Cap Sensors
Wireless Tire Pressure and Temperature Monitoring System Instruction Manual Model #: TM-510 510 Cap Sensors Thank you for purchasing the TST Tire Pressure Monitoring System. With minimal care, your new
More informationNO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS.
Table of Contents Table of Contents... 1 Getting Started... 2 ProCal Flash Tool... 2 Verify Package Contents... 2 Getting to Know the ProCal 3 Software... 3 Prepare Vehicle for Flashing... 7 Download Calibration
More information12 VOLT BATTERY & ELECTRICAL SYSTEM ANALYSER
12 VOLT BATTERY & ELECTRICAL SYSTEM ANALYSER P/No. BLT700 KIT CONTENTS 1. Battery analyser 2. Storage case 3. Battery chart 4. USB Cable 5. Software on CD 6. Printer paper OVERVIEW 1. LCD display 2. Red
More informationOptional: Wiring a Relay for Gauge Controlled Output
Wiring Installation Instructions for : PYROMETER 2 1/16 Spek Pro Professional Racing Gauge GAUGE 12-Pin Wiring Harness & Plug Firewall Grommet DIAGRAM 1 Black-Engine Ground 12-Pin Wiring Harness CUP Coil
More informationRR Concepts. The StationMaster can control DC trains or DCC equipped trains set to linear mode.
Jan, 0 S RR Concepts M tation aster - 5 Train Controller - V software This manual contains detailed hookup and programming instructions for the StationMaster train controller available in a AMP or 0AMP
More informationCORNERING LIGHTING MODULE CLM02-CAN INSTALLATION MANUAL
CORNERING LIGHTING MODULE CLM02-CAN INSTALLATION MANUAL QUASAR ELECTRONICS ul. Cieślewskich 2K 03-07 Warszawa tel. (22) 427-3-4..44 http://www.quasarelectronics.pl e-mail: biuro@quasarelectronics.pl OPERATION
More informationDFE PARTS LIST INSTALLATION INSTRUCTIONS PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
1 Fusion Module 1 USB Cable 1 Installation Guide PARTS LIST INSTALLATION INSTRUCTIONS 2 Velcro Strips 1 Alcohol Swab 1 O2 Optimizer 2014 KAWASAKI TERYX 4 DFE-17-054 PLEASE READ ALL DIRECTIONS BEFORE STARTING
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2009-2014 Yamaha YFZ450 R/X Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!
More informationInstalling the EFILive LBZ/LMM DSP2 & DSP5 Custom Operating Systems
Installing the EFILive LBZ/LMM DSP2 & DSP5 Custom Operating Systems Installing the EFILive LBZ/LMM DSP2 & DSP5 Custom Operating Systems Copyright 1998-2009 EFILive Limited. All rights reserved First published
More informationMUSTANG PROJECT. INSTALLING THE Mustang Project LED SEQUENTIAL TAILLIGHT KIT P/N MP-2004-LED AND MP-2004-LED-QK. Price:$9.
WWW.MUSTANGPROJECT.COM VOLUME 6 Price:$9.95 A SafeCode Inc. Publication INSTALLING THE Mustang Project 1996-2004 LED SEQUENTIAL TAILLIGHT KIT P/N MP-2004-LED AND MP-2004-LED-QK Page 2 Read these instructions
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
2011 Honda CBR250R Installation Instructions PARTS LIST 1 Juice Box Pro 1 USB Cable 1 Top Tune CD-ROM 1 Installation Guide 2 Velcro strip 1 Alcohol swab 1 Posi-tap THE IGNITION MUST BE TURNED OFF BEFORE
More informationWireless Tire Pressure and Temperature Monitoring System Color Display Manual. Wide Screen Color Display Model #: TST-507-D-C
Wireless Tire Pressure and Temperature Monitoring System Color Display Manual Wide Screen Color Display Model #: TST-507-D-C Thank you for purchasing the TST Tire Pressure Monitoring System. With minimal
More informationProMax Progressive Controller Installation and Operation Instructions
ProMax Progressive Controller Installation and Operation Instructions These instructions will guide you through the setup, installation, and use of the Nitrous Outlet Promax Progressive Controller. If
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2006-2014 Yamaha Stratoliner/Roadliner 2008-2013 Yamaha Raider Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab 1 O2 Optimizer
More informationWindLab TM Wind Turbine Power System Sample Laboratory Procedure Manual
WindLab TM Wind Turbine Power System Sample Laboratory Procedure Manual WindLab TM is a scaled Wind Turbine Electrical Generation System, designed to function like a full-sized wind turbine system. It
More informationTemperature Programming Quick Reference Guide
Temperature Programming Quick Reference Guide Normal Mode Dial Brightness (press one at a time) Peak Mode Factory Default Reset (Hold for 5 seconds) High Alert Setting Mode Use LEFT or RIGHT buttons to
More informationFUEL MOTO MICRO EFI TUNER YAMAHA GRIZZLY YAMAHA GRIZZLY 700 FIG. FIG. 1 Micro Tuner Module 1 USB Cable 1 Alcohol swab
FIG. FUEL MOTO MICRO EFI TUNER INSTALLATION INSTRUCTIONS 2009-2014 YAMAHA GRIZZLY 550 2007-2016 YAMAHA GRIZZLY 700 FIG. 1 Micro Tuner Module 1 USB Cable 1 Alcohol swab PARTS LIST 1 Installation Guide 2
More informationMCL-3000 SERIES AIR PRESSURE PART# MCL-3K-A
MCL-3000 SERIES AIR PRESSURE PART# MCL-3K-A Thank you for purchasing the Dakota Digital MCL-3K-A gauge for your Harley Davidson Touring bike. This gauge is designed to be a direct, plug in replacement
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List 2004-2014 Suzuki GSX-R600/GSX-R750 Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab 1 O2 Optimizer THE IGNITION MUST BE
More informationUSER GUIDE 1 USER GUIDE
USER GUIDE 1 USER GUIDE 1 TABLE OF CONTENTS IN THE BOX...3 NAVIGATING THE MENUS...3 MENU LAYOUT...3 UPDATE YOUR PROGRAMMER...4 CONNECT WITH THE MOTORCYCLE...5 TUNE YOUR MOTORCYCLE...6 ADDITIONAL FEATURES...8
More informationUser Manual WatchPower App
User Manual WatchPower App Management Software for Inverter Table of Contents 1. Introduction... 1 2. WatchPower App Install and Uninstall... 1 2.1. System Requirement... 1 2.2. Software Install... 1 2.3.
More informationIdle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications
An ISO 9001:2008 Registered Company Idle Timer Controller - ITC515-A 2015-2018 Ford Transit Contact InterMotive for additional vehicle applications Overview The ITC515-A system will shut off gas or diesel
More informationGENERAL MOTORS SERVICE PARTS OPERATION 6200 Grand Pointe Drive, Grand Blanc, MI 48439
LS CIRCLE TRACK IGNITION CONTROLLER 19355863 Ignition Control for Carbureted LS Series Engines (24x Crankshaft Index/1x Camshaft Index, 58x Crankshaft Index/4x Camshaft Index) Parts Included Quantity Ignition
More informationInstallation Guide. Installing and Configuring the Meritor WABCO Trailer RSS 2M with InfoLink Lift Axle Control Option. Hazard Alert Messages
Installation Guide Revised 01-17 Installing and Configuring the Meritor WABCO Trailer RSS 2M with InfoLink Lift Axle Control Option Kits 400 850 845 0, 400 850 841 0 and 400 850 056 2. Must be used with
More informationGM ALLISON 6 SPEED LCT-1000/2000/2400 CO-PILOT Parts list
2006-10 GM ALLISON 6 SPEED LCT-1000/2000/2400 CO-PILOT Parts list Co-Pilot Computer (1) 601-800-4308 Solenoid Block (1) 601-109-4308 External Wiring Harness (1) 601-011-4308 Internal Wiring Harness (1)
More informationCustom Dynamics LED Tri-Bar Fender Tip Installation Instructions
Custom Dynamics LED Tri-Bar Fender Tip Installation Instructions We thank you for purchasing the Custom Dynamics LED Tri-Bar Fender Tip! Our products utilize the latest technology and high quality components
More informationIdle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC520-A 2009-2018 Ford E Series 2008-2016 Ford F250 - F550 2017-2018 Ford F250 - F550 (*B-ITC520-A) 2016-2018 F650/F750 *Uses the Ford 24-Pin
More informationINSTALLATION INSTRUCTIONS. Yamaha G19 Installation Notes
620 Magnolia Avenue Suite B Ontario, CA 91762 (909) 923-1973 INSTALLATION INSTRUCTIONS Yamaha G19 Installation Notes CURTIS 1232, 1234, 1236 OR 1238 AC INDUCTION MOTOR/ CONTROLLER Yamaha G 19 Installation
More informationWWW.MORETRACTION.COM TMS-5500-SL ELECTRONIC TRACTION CONTROL US PATENT 6,577,944 Other Patents Pending COPYRIGHT NOTICE Copyright 1999-2013 Davis Technologies, LLC. All rights reserved. Information in
More informationDCC-2500 Digital Climate Control for Vintage Air GEN-IV systems
INSTALLATION AND OPERATOR S MANUAL FOR DCC-2500 Digital Climate Control for Vintage Air GEN-IV systems PARTS INCLUDED WITH THIS SYSTEM Vent sensor housings: 2 1 / 2 housings (x2) 2 housings (x2) Installation/operator
More informationFUEL MOTO MICRO EFI TUNER YAMAHA RAPTOR Micro Tuner Module 1 USB Cable 1 Alcohol swab. 1 Installation Guide 2 Velcro strips
FUEL MOTO MICRO EFI TUNER INSTALLATION INSTRUCTIONS 2006-2017 YAMAHA RAPTOR 700 PARTS LIST 1 Micro Tuner Module 1 USB Cable 1 Alcohol swab 1 Installation Guide 2 Velcro strips PLEASE READ ALL DIRECTIONS
More informationAdvanced User Manual
Advanced User Manual Banks SpeedBrake For use with Palm Tungsten E2 2004-2005 Chevy/GMC 6.6L (LLY) Turbo-Diesel Pickup THIS MANUAL IS FOR USE WITH KITS 55419 & 55421 Gale Banks Engineering 546 Duggan Avenue
More informationMSD Boost Control Module PN 7763
MSD Boost Control Module PN 7763 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationProdigy to Encore HD Manual Powder Spray System Upgrade Kit
Instruction Sheet P/N 60780-0 Prodigy to Encore HD Manual Powder Spray System Upgrade Kit WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this
More informationMSD Boost Control Module PN 77631
MSD Boost Control Module PN 77631 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationAppendix 3 V1.1B Features
Appendix 3 V1.1B Features The v1.1b of the Valve Spring Tester adds several new features, which are described in this Appendix. In addition, the Automatic Spring Tester was released after the original
More informationMCL-3000 SERIES OIL TEMP PART# MCL-3K-TMP
MCL-3000 SERIES OIL TEMP PART# MCL-3K-TMP Thank you for purchasing the Dakota Digital MCL-3K-TMP gauge for your Harley Davidson Touring bike. This gauge is designed to be a direct, plug in replacement
More informationEPAS Desktop Pro Software User Manual
Software User Manual Issue 1.10 Contents 1 Introduction 4 1.1 What is EPAS Desktop Pro? 4 1.2 About This Manual 4 1.3 Typographical Conventions 5 1.4 Getting Technical Support 5 2 Getting Started 6 2.1
More informationPLATINUM PRO PLUG-IN HONDA CIVIC (EP3)
PLATINUM PRO PLUG-IN HONDA CIVIC (EP3) 2002-2005 (HT055047) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com
More informationLeafBox manual, v How to set the LeafBox?
LeafBox manual, v1.0 LeafBox should be installed to accelerator pedal plug of Nissan Leaf. It does not matter generation or year of production, but there are various settings depend on your driving mood,
More informationPLATINUM SPORT GM (HT051100) QUICK START GUIDE. Version
PLATINUM SPORT GM (HT051100) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for
More informationALFA-Club. Owners Manual Rev 4.0, August Small Systems Specialists 201 N. Lobb Ave. Pen Argyl, PA Memory Checkpoint Clock
ALFA-Club Memory Checkpoint Clock Dual Odometer/Clock Owners Manual Rev 4.0, August 2018 Small Systems Specialists 201 N. Lobb Ave. Pen Argyl, PA 18072 609-301-0541 ALFA@Rally.cc On the web at www.rally.cc
More informationBegin to Use The New ESC: Before use the new ESC please carefully check every connections are correct or not. Yellow motor wire B Blue motor wire A
HIMOTO ZTW Brushless Electronic Speed Control for car or truck Thank you for purchasing ZTW Brushless Electronic Speed Controller(ESC). The ZTW electronic speed control (ESC) is specifically designed for
More informationRS-351-EDP. Installation Guide
RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...
More informationECLIPSE Laundry Dispenser Controller
ECLIPSE Laundry Dispenser Controller Reference Manual Programming and Operation Online and downloadable Product Manuals and Quick Start Guides are available at www.hydrosystemsco.com Please check online
More informationPLATINUM PRO PLUG-IN Nissan Z32 300ZX
PLATINUM PRO PLUG-IN Nissan Z32 300ZX (HT-055107) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationWideband Failsafe Gauge Parts List
Wideband Failsafe Gauge Parts List Qty Qty 1 Wideband Failsafe Gauge 1 Faceplate, Lambda Black 1 UEGO Sensor 1 Faceplate, Vacuum Black 1 UEGO Harness 1 Harness, Input / Output 1 Install Kit w/ Bung 1 Rubber
More informationTECHNICAL SPECIFICATIONS. CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules devices HKPY2VC/A 3 modules devices
USER GUIDE Mobility MiX Cart HKPX2VC/A Mobility MiX Cart 30 HKPY2VC/A Mobility MiX Cart 45 TECHNICAL SPECIFICATIONS CAPACITY per slot width 1ʺ 1.25ʺ 1.5ʺ HKPX2VC/A 2 modules 30 24 20 devices HKPY2VC/A
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Parts List Husqvarna 250, 310, 450, 510, 610, and 630 Models Installation Instructions 1 Power Commander FC 1 USB Cable 1 Installation Guide 2 Dynojet Decals 2 Velcro 1 Alcohol swab 1 Posi-tap 1 O2 Optimizer
More informationApplied BioPhysics Inc
Applied BioPhysics Inc 185 Jordan Rd, Troy, NY 12180 info@biophysics.com ECIS p-flow Peristaltic Pump Manual, rev D. Pump Specifications Maximum flow rate with 3.18mm ID tubing 24ml/min Minimum flow rate
More informationFUEL MOTO MICRO EFI TUNER POLARIS RZR800 / S / 4. 1 Micro Tuner Module 1 USB Cable 1 Alcohol swab. 1 Installation Guide 2 Velcro 2 Zip ties
FUEL MOTO MICRO EFI TUNER INSTALLATION INSTRUCTIONS 2011-2014 POLARIS RZR800 / S / 4 PARTS LIST 1 Micro Tuner Module 1 USB Cable 1 Alcohol swab 1 Installation Guide 2 Velcro 2 Zip ties PLEASE READ ALL
More informationInstruction of connection and programming of the VECTOR controller
Instruction of connection and programming of the VECTOR controller 1. Connection of wiring 1.1.VECTOR Connection diagram Fig. 1 VECTOR Diagram of connection to the vehicle wiring. 1.2.Connection of wiring
More informationFast Charger SL01/02
Fast Charger SL01/02 User Manual This manual contains important information for commissioning and handling. Please read them first before use of the SL01 or SL02 and keep these instruction, so you can
More informationPLATINUM PRO PLUG-IN Nissan Z32 300ZX
PLATINUM PRO PLUG-IN Nissan Z32 300ZX (HT-055107) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects
More informationPIM701 (Police Interface Module) Dodge Charger Pursuit
An ISO 9001:2008 Registered Company PIM701 (Police Interface Module) 2015-2017 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired
More informationEasyCoding User Manual
EasyCoding User Manual Table of contests 1. Software operating system... 2 2. Software download and installation... 2 2.1 Software download... 2 2.2 Software installation... 2 3. Product instruction...
More informationMSD Power Grid System Controller PN 7730/77303
MSD Power Grid System Controller PN 7730/77303 Parts Included: 1 - System Controller, PN 7730 / PN 77303 1-4Gb SD Card 1 - Micro-USB Cable 1 - MSD View CD-Rom 1 - Fiber Optic Plug 1 - CAN Terminator Cap
More informationMSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010
MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 Parts Included 1 Ignition Controller, PN 6010 1 Pro-Data+ Software CD 1 Harness 1 Parts Bag 6 Timing Modules Optional Accessories
More informationobdtoolshop.co.uk EasyCoding User Manual
EasyCoding User Manual Table of contests 1. Software operating system...2 2. Software download and installation...2 2.1 Software download...2 2.2 Software installation...2 3. Product instruction...6 3.1
More information