Vehicle Service Parts (may be required for reassembly) Legend

Size: px
Start display at page:

Download "Vehicle Service Parts (may be required for reassembly) Legend"

Transcription

1 Toyota Corolla 2016 Part Number: Accessory Code: KE1000 Conflicts Note: Not for installation on vehicles equipped with factory keyless entry Additional Items Required For Installation Item# Quantity Req. Description Kit Contents Item# Quantity Req. Description 1 1 Control Module 2 1 Main Harness 3 1 Hardware Bag 4 1 Valet Switch " Cable Ties Button Transmitter 7 1 Owner's Card Vehicle Service Parts (may be required for reassembly) Item# Qty Description Control Module Transmitter Main Installation Harness On/Off Toggle Control Switch Hardware Bag Headlight Extension Wire Hardware Bag Contents Item# Quantity Req. Description 1 8 Red T-Taps 2 2 Blue T-Taps 3 8 Black T-Taps 4 1 Yellow T-Tap /4" x 2-1/4" Foam Pad 6 6 8" Cable Ties Recommended Tools Safety Tools Special Tools Legend STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CRITICAL PROCESS: Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installation. TOOLS & EQUIPTMENT: This calls out the specific tools and equipment required for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. S SAFETY TORQUE: This mark indicates that torque is related to safety. Installation Tools Phillips Screwdriver Rachet w/ Extension Wire Cutters/Strippers Flashlight Torque Wrench (48 in. lbs.) Needle Nose Pliers Special Chemicals Straight-Slot Screwdriver 10 mm Socket Common Pliers Nylon Trim Tool Wire Crimpers SPECIAL NOTE: After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality. Page 1 of 12 Rev. L 03/07/2016

2 INSTALLATION PREPARATION 1. Familiarize yourself with the installation instructions. Corolla 2016 PREPARING FOR INSTALLATION Negative Battery 2. Inspect kit components (Refer to kit contents and hardware bag contents). VEHICLE PREPARATION Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation o f this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). Safety (eye protection, re-checking torque procedure, etc.). Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). Electrical Component Disassembly/Reassembly (battery disconnection,connector removal, etc.). Fig. 2a Fig. 2b REMOVE THE DRIVER'S SIDE SCUFF PLATE: 1. Disengage the (10) claws and remove the LH scuff plate. (Fig. 2b) REMOVE THE DRIVER'S SIDE KICK PANEL: 1. Remove the plastic nut, disengage the (1) clip and remove the LH kick panel. (Fig. 2c) Fig. 2c Screw REMOVE THE LOWER INSTRUMENT FINISH PANEL (LH): 1. Pry off the far right blank knock out cover using the slot at the bottom of the knock out and remove the screw located behind. Use protective tape to avoid damage to the finish panel when prying. (Fig. 2d) Fig. 2d Page 2 of 12

3 PREPARING FOR INSTALLATION REMOVE THE LOWER INSTRUMENT FINISH PANEL (LH); cont: 1. Disengage the (8) clips, and remove the lower instrument finish panel. Then disconnect any electrical connectors. Using needle-nose pliers, disengage harness clip and remove clip from panel. Remove panel from vehicle and set the panel aside where it will not be damaged. (Fig. 3a) Fig. 3a REMOVE THE LOWER STEERING COLUMN COVER: 1. Remove the (2) philips screws securing the steering column cover. Then disengage the claws and remove the lower half of the steering column cover. (Fig. 3b) Fig. 3b T-TAP INSTALLATION When installing female T-Tap connectors, be sure the wire is located inside the wire channel of the female T-Tap connector before closing the connector over the wire with pliers. When possible, install T-Taps at least 1" away from connector. Step A Step B Step C T-Tap Wire from main keyless harness IMPORTANT! After installation, inspect and ensure that Keyless System Harnesses are clear of all HOT, SHARP or MOVING objects. IMPORTANT! Care MUST be exercised when using the BLACK T-Taps. To avoid damage and broken wires, please note: Ensure there is NO tension on the T-Tap connection when securing the harness. The wire should be slack. Excessive manipulation and/or stress on the wire connection could lead to wire breakage. Center the wire in the metal insert, NOT the plastic side of the T-Tap. Misalignment of the wire against the metal insert could lead to cutting the wire. It is recommended to close close the T-Tap with your fingers (Step A above). After the T-Tap has been closed with your fingers, applying light pressure with a set of pliers will complete the connection. Page 3 of 12

4 WIRING DIAGRAM - Corolla WIRING DIAGRAM PINK / WHITE WIRE [ LF Door Unlock Switch ]: Use black T-Tap and connect to the YELLOW WIRE in connector HE1, location 3. RED WIRE [ +12 VDC ]: Use black T-Tap and connect to the BLUE WIRE in connector E4, location 4. YELLOW WIRE [ Accessory ]: Use black T-Tap and connect to the BLACK WIRE in connector E4, location 7. BLACK WIRE- (18 GA.) GROUND: Connect to factory ground location in drivers kick panel. GREEN/RED WIRE [ Horn ]: Use black T- Tap and connect to the LT. GREEN WIRE in connector E8, location 9. WHITE WIRE [ Tail lights ]: Use black T-Tap and connect to the WHITE WIRE in connector E10, location 18. BLUE WIRE [ Headlights]: Use black T-Tap and connect to the RED WIRE in connector E10, location 17. PINK WIRE [ LF Door Lock Switch ]: Use black T-Tap and connect to the BLUE WIRE in connector HE1, location 4. PINK / WHITE WIRE [ Unlock Detect ]: Use black T-Tap and connect to the YELLOW WIRE in connector HE2, location AMP WHITE WIRE [ Driver's Door Unlock Motor ]: Towards Door Lock - See Detail A BLUE/WHITE WIRE [ Driver's Door Unlock Motor ]: Towards Body ECU - See Detail A Main Control Module DETAIL "A" DRIVER'S DOOR UNLOCK CIRCUIT Cut the BLACK WIRE in connector HE1, location 1. Strip the insulation from both sides of the cut wire, and crimp the WHITE WIRE from the keyless harness to the HARNESS side of the cut wire. Crimp the BLUE/WHITE WIRE from the keyless harness to the CONNECTOR side of the cut wire. Harness Wires BLUE w/ WHITE Cut & Strip Existing Wire WHITE Page 4 of 12 To Toggle Control Switch

5 CONNECTOR DETAILS Corolla Corolla 1. CONNECTOR E4 : Ignition Switch Location : Steering Column Blue Pin 4 +12V BATT (7.5A AM2) All Connectors Show Terminal View Black Pin 7 +12V ACC (5A AM1) KEYLESS CAR PIN T-TAP Red Blue 4 Black Yellow Black 7 Black 2. CONNECTOR E10 : Tail Lights / Head Lights Location : Lower Steering Column Cover Area White Pin 18 Tail Lights Red Pin 17 Head Lights KEYLESS CAR PIN T-TAP White White 18 Black Blue Red 17 Black 3. CONNECTOR E8 : Horn Location : Lower Steering Column Cover Area STOP THERE ARE 2 LT. GREEN WIRES IN CONNECTOR E8. ENSURE CONNECTION IS MADE TO THE LARGER LT. GREEN WIRE IN PIN 9, NOT THE SMALLER LT. GREEN WIRE IN PIN 13. DAMAGE TO THE MODULE WILL OCCUR IF CONNECTED TO THE WRONG WIRE! Lt. Green Pin 9 HORN KEYLESS CAR PIN T-TAP Green/Red Lt. Green 9 Black Page 5 of 12

6 CONNECTOR DETAILS - Corolla 4. CONNECTOR HE1 : Door Locks Location : Driver's Kick Panel Area All Connectors Show Terminal View Black Pin 1 Unlock Motor Yellow Pin 3 Unlock Switch Blue Pin 4 Lock Switch KEYLESS CAR PIN T-TAP Pink Blue 4 Black Pink/White Yellow 3 Black White Black 1 Lock Side Blue Black 1 ECU Side 5. CONNECTOR HE2 - Unlock Detect Location : Driver's Kick Panel Area Yellow Pin 10 UNLOCK DETECT KEYLESS CAR PIN T-TAP Pink/White Yellow 10 Black Page 6 of 12

7 INSTALLING THE KEYLESS ENTRY SYSTEM IMPORTANT! Make sure that the brake pedal, accelerator pedal, and acceletor pedal linkages are free and clear of all security harnesses. Mounting the Main Control Module : 1. Fully extend and lift the tilt and telescoping steering column. Route the main wiring harness to the control module. Use caution when routing to avoid any hot, sharp, or moving objects. Route the main wiring harness BEHIND the factory harness to avoid the harness shorting against the dash brace, as pictured. (Fig. 10a) Factory Harness SET Harness 2. Apply provided adhesive pad to the side of the control module. Using the adhesive pad, mount the control module to the factory dash brace (to the left of the steering column). Sharp Edge Fig. 10a Control Module 3. Secure the control module to the factory brace with 1 long wire tie. (Fig. 10b) Connecting the Security System Harness : SECURING MODULE GROUND: Fig. 10b 1. Locate the factory ground lug in the driver's kick panel area. Secure the black ground wire to the 10mm ground lug, Factory Ground point EA. Set Toggle Control Switch to OFF position. Secure excess wiring, Black ground wire, and the Toggle Control Switch to the factory wiring harness with a wire tie as pictured. (Fig. 10c) EA Factory Ground Point EA Fig. 10c Toggle Control Switch Page 7 of 12

8 COMPLETING THE INSTALLATION: COROLLA S NOTE : Re-torque battery cable to 48in lb. once process is completed. Negative Battery Verify that the DC CUT 30A FUSE is installed prior to testing. TESTING THE SYSTEM: 1. Prior to delivering the vehicle, test all features of the system accordinng to the owner's manual included. LOCK - Press and release the LOCK button on the transmitter. All doors should lock, headlights should come on. UNLOCK - Press and release the UN- LOCK button on the transmitter. The driver's door should unlock, headlights should come on. Press and release the UNLOCK button again. All doors should unlock. Press and hold the PANIC button for approximately 3 seconds. The horn should sound and the parkings lights should flash. Press and release the PANIC button to silence the horn. NOTE: Be sure to test both transmitters that were included in the kit. ASSEMBLE ALL REMOVED PANELS TO THE VEHICLE: 1. Refer again to the vehicle repair manual and reassemble all panels that were removed for installation back onto the vehicle. Test thoroughly, all mechanical components disconnected and or removed from the vehicle during the installation of this accessory. PREPARING THE VEHICLE FOR DELIVERY: 1. To set the arm/disarm chirps to "soft" chirps. 2. Start with the doors in the unlocked position, Toggle Control Switch in the "OFF" position. 3. Turn the ignition key to the on position. 4. Turn the ignition key off, then immediately switch the Toggle Control Switch "ON" then "OFF" 4 times. 5. The vehicle horn should respond with soft horn chirps. 6. Place owner's card in glove compartment. Page 8 of 12

9 PROGRAMMING NEW or REPLACEMENT TRANSMITTERS TO THE SECURITY MODULE: IMPORTANT NOTE : Once you enter the programming mode, if 30 seconds elapse with no activity on the system, the programming mode will be terminated. If this happens, simply start over. STEP 1 STEP 3 To get started, disarm the module by first locating the silver toggle switch in the driver s kick panel. Press the Lock button on the transmitter. The horn will chirp to confirm it has learned the transmitter. 1. Insert the key into the ignition key cylinder and turn to the ON position 3. Flip the toggle switch ON, then OFF. ON OFF ON OFF STEP 4 Repeat Step 3 for all transmitters that you need to program to operate the vehicle. (Maximum of 4 transmitters per vehicle) 4. Turn the ignition key to the OFF position STEP 5 STEP 2 When all transmitters have been programmed, turn the ignition key ON then OFF to exit the program mode. Turn the vehicle s ignition key ON then OFF 7 times at 1 second intervals... 1 Second The vehicle will respond by sounding the horn in a SHORT-SHORT-LONG pattern to confirm programming mode has been termindated....ending in the OFF position. The vehicle will respond by sounding the horn in a SHORT- LONG pattern to confirm you have entered programming mode. The programming mode will automatically terminate after 30 seconds of inactivity. This will be confirmed by the horn sounding a SHORT-SHORT-LONG pattern. If this happens, start over at step 1 to program transmitters. Page 9 of 12

10 VEHICLE FUNCTION CHECKLIST THESE POINTS MUST BE CHECKED TO ENSURE A QUALITY INSTALLATION Head Light If the warning lights remains on, it may indicate a system malfunction. High Beams Turn Signal Lights Tail Lights Stop Lights Backup Lights Hazard Lights Marker Lights Dome/Courtesy Lights Panel/Switch Illumination Accessory Controls/Illumination Rear Window Defogger Key Sensor Buzzer Fog Lights Day Time Running Lights Trunk/Tailgate/Bed Lights Glove Box Light ABS Light Rear Wiper/Washer (if equipped) Clock Accessory Power Socket Starter Audio/Video Power Sliding Door (if equipped) Convenience Memory Settings Heated Seats Page 10 of 12 Massage Seats Power Side Mirrors Side Mirror Defogger Front Windshield Defogger Navigation System Rear Sunshade Cruise Control Light Steering Wheel Audio Control HVAC Power Locks Power Windows Gauges Front Wiper/Washer Hood Latch Release Passenger Air Bag Switch Rollover Side Curtain Air Bag Switch (RSCA) Horn Seat Belt Warning Light If the warning lights remains on, it may indicate a system malfunction. Air Bag Warning Light If the warning lights remains on, it may indicate a system malfunction. Lamp Failure Sensor If the warning lights remains on, it may indicate a system malfunction. Track/Skid Control Light If the warning lights remains on, it may indicate a system malfunction. Tire Pressure Monitoring System (TPMS) Prior to TPMS activation and Pre-Delivery Service (PDS) of the vehicle the TPMS light will blink when IG is turned on. After TPMS activation and PDS of the vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on.

11 Block Diagram System: Corolla: Kit P/N Ground - Connect to Factory Ground Point EA, Driver s Kick Panel. Ignition - Connect to Black Wire (Connector E4, Cavity 7) +12v - Connect to Lt. Blue Wire (Connector E4, Cavity 4) Headlights - Connect to Red wire (Connector E10, Cavity 17) On/Off Toggle Control Switch P/N: C-1 14 Control Module P/N P-W P-W B B Y Y R R L L C-1 15 C-1 13 C-1 23 C-1 11 C-1 10 C-1 5 C-1 6 C-1 21 C-1 7 W W L L P-W P L-W W P-W P L-W W 10 A O-W B-O B-O GR GR C-1 9 C-1 18 C-1 17 C-1 8 Tail Lights - Connect to White Wire (Connector E10, Cavity 18) Horn - Connect to Lt. Green Wire (Connector E8, Cavity 9) Door Unlock detect - Connect to Yellow Wire (Connector HE2, Cavity 10) Door Unlock Switch - Connect to Yellow Wire (Connector HE1, Cavity 3) Door Lock Switch - Connect to Blue Wire (Connector HE1, Cavity 4) Driver s Door Unlock Motor - Connect to Black Wire (Connector HE1, Cavity 1) Driver s Door Unlock Motor - Connect to Black Wire (Connector HE1, Cavity 1) Factory wire is cut in half, refer to installation instructions for additional details. Page 11 of 12

12 Connector C-1: Harness Connector Connector End View Checking the Harness Pinouts: Pin Wire Color Wire Function Test Reference Proper Operation 1 No Wire N/A 2 No Wire N/A 3 No Wire N/A 4 No Wire N/A 5 Pink/White Unlock All Doors Pin 5 to Ground. 6 Pink/White Unlock Detect Pin 6 to Ground. 7 Blue/White Driver s Unlock Motor ECU Side Pin 7 to Ground. 8 White Driver s Unlock Motor Motor Side Pin 8 to Ground 9 Orange/White Active Out Pin 9 to Ground. Always 12 VDC. 10 Green/Red Horn Chirp / Panic Pin 10 to Ground. 11 White Tail Light Flash Pin 11 to Ground. 12 No Wire N/A 13 Red Battery Pin 13 to Ground. Approximately 12 VDC. Approximately 12VDC at rest. Continuity to Ground (pulsed) when driver s unlock switch is in the UNLOCK position or if keyless UNLOCK function is active (2nd UNLOCK press). Approximately 12 VDC at rest. Continuity to Ground (pulsed) when driver s unlock switch is in the UNLOCK position or if keyless UNLOCK function is active (2nd UNLOCK press). Approximately 0 VDC at rest. Approximately 12 VDC (pulsed) when driver s unlock switch is pressed. Approximately 12 VDC (pulsed) when keyless UNLOCK function is activated (first UNLOCK press). Approximately 0 VDC at rest. Approximately 12 VDC at rest. Continuity to Ground (pulsed) when horn pad is pressed / honking. Approximately 12 VDC at rest. Continuity to Ground (pulsed) when keyless is active Continuity to Ground (solid) tail lights are switched to ON at headlight switch. 14 Black Ground Pin 14 to Ground. Always continuity less than 1 ohm. 15 Yellow Ignition Pin 15 to Ground. 16 No Wire N/A 17 Gray Programming Switch Pin 17 to Pin Black/Orange Programming Switch Pin 18 to Pin 17. Always continuity to Ground. 19 No Wire N/A 20 No Wire N/A 21 Pink Lock Pin 21 to Ground. 22 No Wire N/A 23 Blue Headlight Pin 23 to Ground. 24 No Wire N/A Approximately 12 VDC when the key is turned to the ON/Run position. Approximately 0 VDC when key is turned OFF. Continuity to Ground when programming switch is in the ON position. No Continuity to Ground when programming switch is in the OFF position. Approximately 12 VDC at rest. Continuity to Ground when driver s lock switch is in the LOCK position or if keyless LOCK function is active. Approximately 12 VDC at rest. Continuity to Ground for 30 seconds after LOCK or UNLOCK operation performed on keyless system. Continuity to Ground when Head Light Hi-Beam FLASH is Activated on the Headlight Switch. Page 12 of 12

Vehicle Service Parts (may be required for reassembly) Legend

Vehicle Service Parts (may be required for reassembly) Legend Toyota Part Number: 00016-32901 Accessory Code: KE1 Corolla 2014 Note: Not for installation on vehicles equipped with factory keyless entry Additional Items Required For Installation Item# Quantity Req.

More information

TOYOTA YARIS KEYLESS ENTRY SYSTEM

TOYOTA YARIS KEYLESS ENTRY SYSTEM TOYOTA YARIS 2011 - KEYLESS ENTRY SYSTEM Part Number: 00016-32901 Accessory Code: KE1 Conflicts Not for installation in vehicles equipped with factory installed keyless entry. Kit Contents Item # Quantity

More information

Conflicts. Prius C 2014 Keyless Entry Upgrade. TOYOTA Part Number: Code: QS10. Vehicle Service Parts (May be required for reassembly)

Conflicts. Prius C 2014 Keyless Entry Upgrade. TOYOTA Part Number: Code: QS10. Vehicle Service Parts (May be required for reassembly) TOYOTA Part Number:00016-47032 Code: QS10 Conflicts 1. Vehicle's with out factory immobilizer Kit Contents Item# Quantity Req. Description 1 1 Security Module 2 1 Shock Sensor, Dual Stage 3 1 LED / Valet

More information

Conflicts. Scion FR-S Keyless Entry Upgrade Alarm Part Number: Code: YQ20. Vehicle Service Parts (may be required for reassembly)

Conflicts. Scion FR-S Keyless Entry Upgrade Alarm Part Number: Code: YQ20. Vehicle Service Parts (may be required for reassembly) 2013 - Part Number: 00016-32910 Code: YQ20 Conflicts Kit Contents Item# Quantity Req. Description 1 1 Security Module 2 1 Shock Sensor, Dual Stage 3 1 LED / Valet Swicth 4 2 Window Warning Decals 5 1 Shock

More information

TOYOTA TUNDRA IMPACT SENSOR

TOYOTA TUNDRA IMPACT SENSOR TOYOTA TUNDRA 2010 - IMPACT SENSOR Part Number: 00016-47031 Accessory Code: QG1 Kit Contents Item # Quantity Reqd. Description 1 1 Security Interface Module 2 1 Shock Sensor 3 1 Main Harness 4 1 Hardware

More information

Conflicts. Camry L (ECO Grade) Security System with Keyless Entry. Part Number: Accessory Code: QK1

Conflicts. Camry L (ECO Grade) Security System with Keyless Entry. Part Number: Accessory Code: QK1 2013- Part Number: 00016-32905 Accessory Code: QK1 Conflicts Note: NOT FOR INSTALLATION ON VEHICLES WITH FACTORY THEFT DETERRENT SYSTEMS. Kit Contents Item # Quantity Reqd Description 1 1 Keyless Security

More information

TOYOTA HIGHLANDER IMPACT SENSOR

TOYOTA HIGHLANDER IMPACT SENSOR TOYOTA HIGHLANDER 2010 - IMPACT SENSOR Part Number : 00016-47031 Accessory Code: QG1 Conflicts Not for installation on vehicles with factory theft deterrent systems - hybrid. Kit Contents Item # Quantity

More information

TOYOTA 4Runner Keyless Entry Upgrade Alarm

TOYOTA 4Runner Keyless Entry Upgrade Alarm TOYOTA 4Runner 2013 - Keyless Entry Upgrade Alarm Part Number: 00016-32910 Accessory Code: QSNS10 Conflicts Note: NOT FOR INSTALLATION ON VEHICLES EQUIPPED WITH SMART KEY General Applicability Used on

More information

Conflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)

Conflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly) TOYOTA 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4 1 Hardware

More information

XM Adapter Cable (P/N: ) MUST be used for this vehicle.

XM Adapter Cable (P/N: ) MUST be used for this vehicle. TOYOTA 2013 - Part Number:00016-00076 Code: RX30 XM Adapter Cable (P/N: 00016-00076-10) MUST be used for this vehicle. Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description

More information

Conflicts. TOYOTA Prius XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)

Conflicts. TOYOTA Prius XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly) TOYOTA Prius 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4

More information

TOYOTA COROLLA 2009 TVIP V4 PREPARATION

TOYOTA COROLLA 2009 TVIP V4 PREPARATION PREPARATION Part #: PT398-02080 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.

More information

TOYOTA COROLLA 2010 TVIP V4 PREPARATION

TOYOTA COROLLA 2010 TVIP V4 PREPARATION PREPARATION Part #: PT398-02080 or PT398-02100 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles

More information

LEXUS CT 200h 2011 TVIP V2 PREPARATION

LEXUS CT 200h 2011 TVIP V2 PREPARATION PREPARATION Part #: PT398-76110 Conflicts: Kit Contents GBS ECU V2 Harness GBS ECU Bracket Nut Microphone Foam Tape Wire Tie x1 x1 x1 x1 x1 x2 x15 08190-0C820 08192-6C820 Window Label Owner s Guide PT398-60084

More information

LEXUS RX TVIP V2 PREPARATION

LEXUS RX TVIP V2 PREPARATION PREPARATION Part #: PT398-48090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Vehicles without Factory Alarm System. Kit Contents GBS

More information

TOYOTA VENZA 2009 TVIP V2 PREPARATION

TOYOTA VENZA 2009 TVIP V2 PREPARATION PREPARATION Part #: PT398-0T092 Conflicts: Kit Contents Do not install into Vehicles without Factory Alarm System. GBS ECU GBS ECU Bracket GBS Harness GBS Microphone Wire Tie Foam Tape M6 Tapping Screw

More information

LEXUS ES TVIP V2 PREPARATION

LEXUS ES TVIP V2 PREPARATION PREPARATION Part #: PT398-33132 Conflicts: Kit Contents GBS ECU GBS ECU Bracket V2 Harness M6 Bolt Washer Wire Tie GBS Microphone x1 x1 x1 x1 x1 x5 08190-0C820 91651-60618 08192-6C820 x1 Foam Tape V2 Window

More information

TOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT

TOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT Preparation Part Number: PT398-48083 Conflicts Do not install into vehicles without RKE systems. Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory Kit Contents

More information

TOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: PT398-34111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts Do not install into vehicles without RKE system. Recommended Sequence of

More information

TOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation

TOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation Preparation Part Number: 08586-48070 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 ECU Mounting Bracket Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Microphone

More information

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:

More information

TOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION

TOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION PREPARATION Part #: PT398-0T110 Conflicts: Will not program with Techstream Lite. Kit Contents RES ECU RES ECU Bracket RES Harness M6 Screw Wire Tie Splicing Connector Remote Label x1 x1 x1 x1 x5 x1 x2

More information

SCION xa LIMITED EDITION SECURITY WITH RKE (V3)

SCION xa LIMITED EDITION SECURITY WITH RKE (V3) Preparation Part Number: 08586-53840 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 V3 Security ECU 3 2 Remote Control Transmitters 4 1 Piezo Buzzer 5 1 Status Monitor 6 1 Radar Sensor

More information

Toyota Sienna. Installation Manual: Toyota Sienna. Power Lift Gate System. Page 1 of 12

Toyota Sienna. Installation Manual: Toyota Sienna. Power Lift Gate System. Page 1 of 12 Toyota Sienna Installation Manual: Toyota Sienna Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage

More information

TOYOTA Highlander / Highlander HV 2014 TVIP V2 PREPARATION

TOYOTA Highlander / Highlander HV 2014 TVIP V2 PREPARATION PREPARATION Part #: PT398-48141 Conflicts: Do not install into Vehicles without Factory Alarm System. Kit Contents GBS ECU GBS ECU Bracket V2 Harness M6 Nut Bolt Jumper Connector Wire Tie DISCARD x1 08190-0C820

More information

Kia Sedona. Installation Manual: Kia Sedona. Power Lift Gate System. Page 1 of 13

Kia Sedona. Installation Manual: Kia Sedona. Power Lift Gate System. Page 1 of 13 Kia Sedona Installation Manual: Kia Sedona Power Lift Gate System Page 1 of 13 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused

More information

TOYOTA TUNDRA TVIP V5

TOYOTA TUNDRA TVIP V5 Preparation Part Number: PT398-34142 Conflicts Do not install into vehicles with Factory Alarm Systems or SR grade vehicles. Do not use Techstream Lite for Registration. Recommended Sequence of Application

More information

TOYOTA FJ CRUISER TVIP V5 Preparation

TOYOTA FJ CRUISER TVIP V5 Preparation Preparation Part Number: 08586-36822 Conflicts Do not be installed in vehicles with factory Anti-theft alarm, or Vehicle without Factory Keyless Entry Systems. Recommended Sequence of Application Item

More information

TOYOTA YARIS HATCHBACK TVIP V3 (RS3200) Preparation

TOYOTA YARIS HATCHBACK TVIP V3 (RS3200) Preparation Preparation Part Number: 08586-53810 Kit Contents Item # Quantity Reqd. Description 1 1 V3 ECU 2 1 Piezo Buzzer 3 1 Wire Harness 4 1 ECU Mounting Bracket 5 2 Remote Control Transmitter 6 1 Butyl Tape 7

More information

TOYOTA CAMRY TVIP V2 (GBS WITH ADD ON)

TOYOTA CAMRY TVIP V2 (GBS WITH ADD ON) Preparation Part Number: 08586-3T930 Kit Contents Item # Quantity Reqd. Description 1 2 Wire Harness (One wire harness is only for RS3200+) 2 1 GBS ECU 3 1 GBS Mounting Bracket 4 1 Microphone Hardware

More information

TOYOTA RAV TVIP V5

TOYOTA RAV TVIP V5 Preparation Part Number: 08586-42810 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 Security ECU Mounting Bracket 4 1 GBS ECU Mounting Bracket 5 1 Status Monitor 6 1 Security

More information

TOYOTA RAV4 w/smart 2009 TVIP V4 PREPARATION

TOYOTA RAV4 w/smart 2009 TVIP V4 PREPARATION PREPARATION Part #: PT398-42110 Conflicts: Do not install into Vehicles manufactured from November 2012 and Onwards. Kit Contents RES ECU Gateway ECU RES ECU Bracket Gateway ECU Bracket Remote Label Key

More information

TOYOTA PRIUS 2010 TVIP V5 PREPARATION

TOYOTA PRIUS 2010 TVIP V5 PREPARATION PREPARATION Part #: PT398-47090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.

More information

TOYOTA PRIUS 2010 TVIP V4 PREPARATION

TOYOTA PRIUS 2010 TVIP V4 PREPARATION PREPARATION Part #: PT398-47091 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.

More information

Keyless Upgrade Alarm

Keyless Upgrade Alarm Toyota Matrix 009 - Keyless Upgrade Alarm Part Number: 0006-940 Accessory Code: QS Kit Contents Item # Quantity Reqd Description Security Module Shock Sensor 3 LED Valet Switch 4 HP Switch Ext. 5 Window

More information

Conflicts. TOYOTA Highlander CAR LINK (W/O Remote Start) Part Number: Accessory Code: QL1. Doc PIO / DIO Rev.

Conflicts. TOYOTA Highlander CAR LINK (W/O Remote Start) Part Number: Accessory Code: QL1. Doc PIO / DIO Rev. Doc. 06.107.00 PIO / DIO Rev. A 04/26/11 TOYOTA Highlander 2011 - CAR LINK (W/O Remote Start) Part Number: 00016-00077 Accessory Code: QL1 Conflicts Note: Kit Contents Item # Quantity Reqd. Description

More information

SCION tc SECURITY (V5) Preparation

SCION tc SECURITY (V5) Preparation Preparation Part Number: PT398-21070 Kit Contents Item # Quantity Reqd. Description 1 1 2 1 GBS ECU Hardware Bag Contents Item # Quantity Reqd. Description 1 1 V5 Security ECU 2 1 ECU Mounting Bracket

More information

LEXUS RX 450h 2010 TVIP V4 PREPARATION

LEXUS RX 450h 2010 TVIP V4 PREPARATION PREPARATION Part #: PT398-48112 Conflicts: Kit Contents Will not Program with Techstream Lite. RES ECU RES ECU Bracket RES Harness Key Tag Engine Room Label Remote Label Window Label English x2 English

More information

TOYOTA TACOMA TVIP V5

TOYOTA TACOMA TVIP V5 Preparation Part Number: PT398-35090 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor/Microphone 5 2 Warning Labels (English) 6 2 Warning

More information

Installation Manual: Honda CRV Power Lift Gate System

Installation Manual: Honda CRV Power Lift Gate System Installation Manual: Honda CRV Power Lift Gate System Page 1 of 18 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper

More information

TOYOTA CAMRY HYBRID TVIP V5 (RS3200 PLUS) Preparation

TOYOTA CAMRY HYBRID TVIP V5 (RS3200 PLUS) Preparation Preparation Part Number: 08586-3T940-AA Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 3 1 ECU Mounting Bracket NOTE: Part number of this accessory may not be the same as the part number

More information

TOYOTA TACOMA TVIP V5

TOYOTA TACOMA TVIP V5 Preparation Part Number: PT398-35121 Conflicts Note: Must not be installed in Vehicles with Factory Alarm System and 2013- Vehicles with (4WD Double Cab 6MT and Off-Road Package). Kit Contents Item # Quantity

More information

Installation Manual: Jeep Cherokee Power Lift Gate System

Installation Manual: Jeep Cherokee Power Lift Gate System Installation Manual: Jeep Cherokee Power Lift Gate System Page 1 of 11 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper

More information

Chevrlot Equinox. Installation Manual: Chevrlot Equinox. Power Lift Gate System. Page 1 of 11

Chevrlot Equinox. Installation Manual: Chevrlot Equinox. Power Lift Gate System. Page 1 of 11 Chevrlot Equinox Installation Manual: Chevrlot Equinox Power Lift Gate System Page 1 of 11 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage

More information

Installation Manual: Jeep Cherokee Power Lift Gate System

Installation Manual: Jeep Cherokee Power Lift Gate System Installation Manual: Jeep Cherokee Power Lift Gate System Page 1 of 11 NOTE: Installation Precaution Kit Details Power Cable 4120353 1. It is recommended to have this product installed by a professional

More information

TOYOTA HIGHLANDER w/o Smart Key TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA HIGHLANDER w/o Smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: PT398-48111 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory Kit Contents Item # Quantity Description 1 1 Wire Harness

More information

Nissan Rogue. Installation Manual: Nissan Rogue. Power Lift Gate System. NOTE: Not for Rogue Sport Models. Page 1 of 13

Nissan Rogue. Installation Manual: Nissan Rogue. Power Lift Gate System. NOTE: Not for Rogue Sport Models. Page 1 of 13 Nissan Rogue Installation Manual: Nissan Rogue Power Lift Gate System NOTE: Not for Rogue Sport Models Page 1 of 13 NOTE: Installation Precaution 1. It is recommended to have this product installed by

More information

Ford Escape. Installation Manual: Ford Escape. Power Lift Gate System. Page 1 of 12

Ford Escape. Installation Manual: Ford Escape. Power Lift Gate System. Page 1 of 12 Ford Escape Installation Manual: Ford Escape Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused

More information

Installation Manual: Hyundai Tucson Power Lift Gate System

Installation Manual: Hyundai Tucson Power Lift Gate System Installation Manual: Hyundai Tucson Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper

More information

TOYOTA RAV TVIP V3

TOYOTA RAV TVIP V3 Section I Installation Preparation Part Number: 08586-4A872 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1 V3

More information

TOYOTA TACOMA 2005 TVIP V5 (RS3200 PLUS) Preparation

TOYOTA TACOMA 2005 TVIP V5 (RS3200 PLUS) Preparation Preparation Part Number: 08586 04840 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor 5 2 Warning Labels 6 1 Owner s Manual 7 1 Warranty Card

More information

TOYOTA TACOMA TVIP V3 (RS3200) Section I - Installation Preparation

TOYOTA TACOMA TVIP V3 (RS3200) Section I - Installation Preparation Section I - Installation Preparation Part Number: 08586-04810 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4

More information

Nissan Rogue. Installation Manual: Nissan Rogue. Power Lift Gate System. Page 1 of 13

Nissan Rogue. Installation Manual: Nissan Rogue. Power Lift Gate System. Page 1 of 13 Nissan Rogue Installation Manual: Nissan Rogue Power Lift Gate System Page 1 of 13 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused

More information

FORM: C 01/06

FORM: C 01/06 Accessory Color Document # 3802 REVISION B 01/09/06 Part Number: 00016-21910 Accessory Code:YQ4 Kit Contents Item # Quantity Reqd Description 1 1 MPX Security Module 2 1 Shock Sensor 3 1 LED Valet Switch

More information

TOYOTA SIENNA w/smart Key and Factory Alarm 2015 TVIP V4 PREPARATION

TOYOTA SIENNA w/smart Key and Factory Alarm 2015 TVIP V4 PREPARATION PREPARATION Part #: PT398-08150 Conflicts: Kit Contents Do not install into Vehicles without Smart Key and Factory Alarm. RES ECU RES ECU Bracket V4 Harness Nut Wire Tie Remote Label Key Tag x1 PT398-0T097

More information

TOYOTA CAMRY wo/smart entry TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA CAMRY wo/smart entry TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: 08586-3T950 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 RES ECU 3 1 BUS ECU 4 1 ECU Mounting Bracket (A) 5 1 ECU Mounting Bracket (B) 6 1 Butyl Tape Hardware

More information

Conflicts - Fog Lights

Conflicts - Fog Lights TOYOTA CAMRY 2013 - BLACKOUT LED DRL Part Number: 00016-32270 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box

More information

TOYOTA PRIUS V 2012 TVIP V4 PREPARATION

TOYOTA PRIUS V 2012 TVIP V4 PREPARATION PREPARATION Part #: PT398-47121 Conflicts: Will not program with Techstream Lite. Kit Contents Screw RES ECU RES ECU Bracket Hood Switch V4 Harness Remote Label (for Hood SW) Wire Tie PT398-0T097 x1 x1

More information

TOYOTA TACOMA XSP-X LED DRL. Part Number: Accessory Code: LDRL10

TOYOTA TACOMA XSP-X LED DRL. Part Number: Accessory Code: LDRL10 TOYOTA TACOMA 2013 - XSP-X LED DRL Part Number: 00016-35230 Accessory Code: LDRL10 Conflicts -None Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Harness bag 4 Hardware Bag

More information

TOYOTA im INTERIOR LIGHT KIT Preparation

TOYOTA im INTERIOR LIGHT KIT Preparation Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1

More information

TOYOTA PRIUS V LED DRL Black-Out

TOYOTA PRIUS V LED DRL Black-Out TOYOTA PRIUS V 2012 - LED DRL Black-Out Part Number: 00016-47021 Accessory Code:LDBO10 Conflicts Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box

More information

TOYOTA TUNDRA TVIP V5

TOYOTA TUNDRA TVIP V5 Preparation Part Number: 08586-OC890 Conflicts Do not install into vehicles with Factory Alarm Systems or without Immobilizer. Do not use Techstream Lite for Registration. Recommended Sequence of Application

More information

TOYOTA SIENNA LED DRL Black-Out

TOYOTA SIENNA LED DRL Black-Out TOYOTA SIENNA 2013 - LED DRL Black-Out Part Number: 00016-08021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver

More information

TOYOTA TACOMA FOG LIGHT

TOYOTA TACOMA FOG LIGHT TOYOTA TACOMA 2012 - FOG LIGHT Part Number: 00016-35220 Accessory Code: LF10 Conflicts - Factory Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Hardware bag 3 1 Switch Assembly

More information

TOYOTA RAV FOG LIGHT

TOYOTA RAV FOG LIGHT TOYOTA RAV4 2011 - FOG LIGHT Part Number: 00016-12013 Accessory Code: LF10 Conflicts - Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Lamp s bezels 3 1 Switch Assembly 4 1 Fog light

More information

TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation

TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag

More information

CAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc

CAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc Doc. 02.126.00 TOYOTA CAMRY PIO / DIO Rev. A 2013-02/26/13 STRIP LED DRL Part Number: 00016-32280 Accessory Code: LDRS10 Conflicts - Only works on Camry SE Kit Contents Item # Quantity Reqd. Description

More information

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

TOYOTA TACOMA LED DRL Black-Out

TOYOTA TACOMA LED DRL Black-Out TOYOTA TACOMA 2013 - LED DRL Black-Out Part Number: 00016-35021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 1 Driver Box 3 1 Harness bag

More information

TOYOTA TUNDRA TVIP V4 Preparation

TOYOTA TUNDRA TVIP V4 Preparation Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM

More information

Part Number: T4R-2N1. Hardware Bag Contents. General Applicability Models with factory fog light. Conflicts -

Part Number: T4R-2N1. Hardware Bag Contents. General Applicability Models with factory fog light. Conflicts - Date: 07.30.2015 TOYOTA TUNDRA 2014-2016 LED Fog Light & DRL 2 in 1 Part Number: T4R-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User

More information

TOYOTA TACOMA FOG LIGHT

TOYOTA TACOMA FOG LIGHT TOYOTA TACOMA 2013 - FOG LIGHT Part Number: 00016-35220 Accessory Code: LF10 Conflicts - Factory Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Hardware bag 3 1 Switch Assembly

More information

SCION xa 2004 SECURITY WITH RKE (V3) Section I Installation Preparation

SCION xa 2004 SECURITY WITH RKE (V3) Section I Installation Preparation Section I Installation Preparation Part Number: 08586 52970 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 V3 Security ECU 3 2 Remote Control Transmitters

More information

Part Number: T4R-2N1. Hardware Bag Contents. General Applicability Models with factory fog light

Part Number: T4R-2N1. Hardware Bag Contents. General Applicability Models with factory fog light 11/10/16 TOYOTA CAMRY 2012-2014 2 in 1 LED UPGRADE KIT Part Number: T4R-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1

More information

Part Number: TTA-2N1. Hardware Bag Contents. General Applicability SR5, TRD Sport, TRD Off-Road, Limited

Part Number: TTA-2N1. Hardware Bag Contents. General Applicability SR5, TRD Sport, TRD Off-Road, Limited Date: 2.10.2016 TOYOTA TACOMA 2016-2 in 1 LED UPGRADE KIT Part Number: TTA-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User s card

More information

TOYOTA PRIUS C FOG LIGHT

TOYOTA PRIUS C FOG LIGHT TOYOTA PRIUS C 2012 - FOG LIGHT Part Number: 00016-47160 Accessory Code: LF10 Conflicts NONE Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Lamp s bezels 3 1 Switch Assembly 4 1 Fog

More information

General Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools

General Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

TOYOTA COROLLA FOG LIGHT

TOYOTA COROLLA FOG LIGHT Doc. 03.69.00 PIO / DIO Rev. C 10/11/12 TOYOTA COROLLA 2012 - FOG LIGHT Part Number: 00016-32118 Accessory Code: LF10 Conflicts - Factory code PM on model 1838 Kit Contents Item # Quantity Reqd. Description

More information

TOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools

TOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number

More information

TOYOTA tc HANDS FREE BLU LOGIC Preparation

TOYOTA tc HANDS FREE BLU LOGIC Preparation TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20

More information

SCION tc 2011 TVIP V4 PREPARATION

SCION tc 2011 TVIP V4 PREPARATION PREPARATION Part #: PT398-21111 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.

More information

Part Number: TCO-314 / TCO-814

Part Number: TCO-314 / TCO-814 Date: 05.02.2014 TOYOTA COROLLA L, LE 2014-15 FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Switch

More information

TOYOTA VENZA HANDS FREE BLU LOGIC Preparation

TOYOTA VENZA HANDS FREE BLU LOGIC Preparation TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear

More information

Part Number: TTA-712. Hardware Bag Contents. General Applicability All models

Part Number: TTA-712. Hardware Bag Contents. General Applicability All models Date: 09.30.2013 TOYOTA TACOMA 2012-15 LED DRL Part Number: TTA-712 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware

More information

Part Number: STC-501. Hardware Bag Contents. General Applicability. Conflicts. Date: SCION tc LED DRL in FOG LIGHT HOUSING

Part Number: STC-501. Hardware Bag Contents. General Applicability. Conflicts. Date: SCION tc LED DRL in FOG LIGHT HOUSING Date: 09.30.2013 SCION tc 2011-2013 LED DRL in FOG LIGHT HOUSING Part Number: STC-501 Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL housings 2 2 Bezels 3 1 Driver Box 4 1 Harness bag 5 1 User

More information

TOYOTA TUNDRA TVIP V3 (RS3000) Section I - Installation Preparation

TOYOTA TUNDRA TVIP V3 (RS3000) Section I - Installation Preparation Section I - Installation Preparation Part Number: 0886-34861 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1

More information

Part Number: TCA-712SE

Part Number: TCA-712SE Date: 09.04.2013 TOYOTA CAMRY SE 2012-14 LED DRL Part Number: TCA-712SE Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion

More information

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear

More information

TOYOTA TACOMA EC REARVIEW MIRROR Preparation

TOYOTA TACOMA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,

More information

Part Number: T4R-2IN1

Part Number: T4R-2IN1 Date: 12.11.2014 TOYOTA HIGHLANDER 2015 LED Fog Light & DRL 2in1 Part Number: T4R-2IN1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User

More information

TOYOTA COROLLA LED DRL eyebrow. Part Number: TCO-DRL

TOYOTA COROLLA LED DRL eyebrow. Part Number: TCO-DRL Part Number: TCO-DRL Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware Bag Contents Item # Quantity Reqd. Description

More information

Part Number: T4R-2N1. Hardware Bag Contents. General Applicability. Conflicts - Limited Models

Part Number: T4R-2N1. Hardware Bag Contents. General Applicability. Conflicts - Limited Models Date: 12.11.2014 TOYOTA HIGHLANDER 2014-2016 LED Fog Light & DRL 2 in 1 Part Number: T4R-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4

More information

LED Fog Light. Conflicts Note: 1832, 1852, 1856, 1872, General Applicability Fits Models

LED Fog Light. Conflicts Note: 1832, 1852, 1856, 1872, General Applicability Fits Models LED Fog Light Year & Model Part Number 2017 Corolla TCO-817 Conflicts Note: 1832, 1852, 1856, 1872, 1874 General Applicability Fits Models 1863 1866 1864 1865 Additional Items Required For Installation

More information

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles

More information

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number:

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number: Section I Installation Preparation Part Number: 08586 52960 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Mounting Bracket 3 1 GBS ECU 4 1 Security

More information

SCION tc 2014 TVIP V4 PREPARATION

SCION tc 2014 TVIP V4 PREPARATION PREPARATION Part #: PT398-21111 Conflicts: Kit Contents Do not install into Vehicles with Smart key or Manual Transmission Vehicles. Will not program with Techstream Lite. Hood Switch RES ECU RES ECU Bracket

More information

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad

More information

SCION TC HANDS FREE BLU LOGIC Preparation

SCION TC HANDS FREE BLU LOGIC Preparation SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information