W60 and W80 Series Valves

Transcription

1 INSTRUCTION MANUAL W0 and W0 Series Valves FORM NO.: REVISION: 1/017 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT.

2

3 SPX FLOW, Inc. 11 Sugar Creek Road Delavan, WI 311 USA Tel: (00) -00 or () Fax: (00) -01 or () Web site: Information contained in this manual is subject to change without notice and does not represent a commitment on the part of SPX FLOW, Inc. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of SPX FLOW, Inc. Copyright 017 SPX FLOW, Inc. All Rights Reserved. Never-Seez is a registered trademark of Bostik Findley. Dow Corning is a registered trademark of Dow Corning Corporation. Loctite is a registered trademark of Henkel Loctite Corporation, U.S.A. Tef-Flow is a trademark of SPX FLOW, Inc. Revision Date: 1/017 Publication: 9-030

4 Table of Contents Waukesha Cherry-Burrell Brand W0/W0 Valves Warranty... Shipping Damage or Loss... Warranty Claim... Safety...7 Care of Component Materials... Stainless Steel Corrosion... Elastomer Seal Replacement Following Passivation... Introduction...9 General Information...9 Factory Inspection...9 Models and Specifications...9 Materials...9 Equipment Serial Number...9 Operating Parameters...10 Seal Compatibility...10 Seat Options...11 Pressure Ratings...11 Installation...1 Welding Instructions...1 Air Supply...1 Pipeline Support...1 Flow Direction...13 W0 Stem Flush Adapter...13 Operation...1 Air Connections...1 Maintainable Actuators...1 ", ", and " Air-to-Raise...1 ", ", and " Air-to-Lower...1 " Air-to-Raise, 3-Position...1 " Air-to-Lower, 3-Position...1 Adjustable-Spring Actuators...1 ", ", and " Air-to-Raise, Adjustable-Spring...1 ", ", and " Air-to-Lower, Adjustable-Spring...1 Maintenance-Free Actuators...1 A, B, and C Size Air-to-Raise, Maintenance-Free...1 A, B, and C Size Air-to-Lower, Maintenance-Free...1 Pressure Setting...17 Air-To-Raise, Adjustable-Spring Actuator...17 Air-to-Lower, Adjustable-Spring Actuator...17 Maintenance...1 Maintenance Intervals...1 Inspection...1 Lubrication...1 Cleaning...1 Valve Removal...19 W1/W1 Valve Disassembly...0 W1/W1 Valve Assembly...1 W1Y Valve Disassembly... W1Y Valve Assembly...3 W/W Valve Disassembly... W/W Valve Assembly... W3/W3 Valve Disassembly... W3/W3 Valve Assembly...7 W/W Valve Disassembly... W/W Valve Assembly...9 WR/WR Valve Disassembly...30 Page /017

5 Waukesha Cherry-Burrell Brand W0/W0 Valves Table of Contents WR/WR Valve Assembly WET/WET Valve Disassembly... 3 WET/WET Valve Assembly W/W Valve Disassembly... 3 W/W Valve Assembly... 3 Seat Replacement Standard Tef-Flow Seat Tef-Flow P Seat Standard Tri Ring Seat... 3 Servicing Actuators: U-cups, O-rings and Bearings Valves with Control Module O-ring and Bearing Replacement:,, and " Actuator U-cup Replacement: " and " Actuator... 0 O-ring and Bearing Replacement: Actuator... 0 U-cup, O-ring and Bearing Replacement: Air-to-Raise 3-Position Actuator... 1 U-cup, O-ring and Bearing Replacement: Air-to-Lower 3-Position Actuator... O-ring and Bearing Replacement: Maintenance-Free Actuator... 3 O-ring and Bearing Replacement:,, and " Adjustable-Spring Actuator... Reversing the Spring Action on the Maintenance-Free Actuator... Reversing the Spring Action on the Maintainable Actuator... 7 Parts Lists... W1/W1 Shutoff Valve... W1Y Shutoff Valve... 0 W/W Divert Valve... W3/W3 Reverse Shutoff Valve... W/W Tank Outlet Valve... WR/WR Tank Outlet Valve... WET Tank Outlet Valve... 0 W/W Non-Slam Divert Valve... W0/W0 Series Single Seat Valve Bodies - inch O.D. Tube sizes... " and " Air-to-Spring or Air-to-Air Actuators... " Air-to-Spring or Air-to-Air Actuators... " and " Air-to-Spring Long Stroke Actuator " Air-to-Air Long Stroke Actuator... 7 " Air-to-Raise 3-Position Actuator... 7 " Air-to-Lower 3-Position Actuator... 7 ", ", and " Air-to-Raise Adjustable-Spring Actuator... 7 ", ", and " Air-to-Lower Adjustable-Spring Actuator Maintenance Free Actuator... 0 Maintenance Free Actuator Cap... 1 Maintenance Free Actuator Yoke... 1 Hand Lock Manual Handle... Hand Lock Long Stroke Manual Handle... 3 Micrometer Handle... Installation Tools... Tef-Flow P Tools... Tri-Ring Tool... Troubleshooting / Page

6 Warranty Waukesha Cherry-Burrell Brand W0/W0 Valves Warranty LIMITED WARRANTY: Unless otherwise negotiated at the time of sale, SPX FLOW US, LLC (SPX FLOW) goods, auxiliaries and parts thereof are warranted to the original purchaser against defective workmanship and material for a period of twelve (1) months from date of installation or eighteen (1) months from date of shipment from factory, whichever expires first. If the goods or services do not conform to the warranty stated above, then as Buyer's sole remedy, SPX FLOW shall, at SPX FLOW's option, either repair or replace the defective goods or re-perform defective services. Third party goods furnished by SPX FLOW will be repaired or replaced as Buyer's sole remedy, but only to the extent provided in and honored by the original manufacturer's warranty. Unless otherwise agreed to in writing, SPX FLOW shall not be liable for breach of warranty or otherwise in any manner whatsoever for: (i) normal wear and tear; (ii) corrosion, abrasion or erosion; (iii) any good or services which, following delivery or performance by SPX FLOW, has been subjected to accident, abuse, misapplication, improper repair, alteration, improper installation or maintenance, neglect, or excessive operating conditions; (iv) defects resulting from Buyer's specifications or designs or those of Buyer's contractors or subcontractors other than SPX FLOW; or (v) defects resulting from the manufacture, distribution, promotion or sale of Buyer's products. THE WARRANTIES CONTAINED HEREIN ARE THE SOLE AND EXCLUSIVE WARRANTIES AVAILABLE TO BUYER AND SPX FLOW HEREBY DISCLAIMS ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING REPAIR, REPLACEMENT AND RE-PERFORMANCE OBLIGA- TIONS STATE SPX FLOW'S ENTIRE AND EXCLUSIVE LIABIL- ITY AND BUYER'S EXCLUSIVE REMEDY FOR ANY CLAIM IN CONNECTION WITH THE SALE AND FURNISHING OF SER- VICES, GOODS OR PARTS, THEIR DESIGN, SUITABILITY FOR USE, INSTALLATION OR OPERATIONS. Shipping Damage or Loss Warranty Claim If equipment is damaged or lost in transit, file a claim at once with the delivering carrier. The carrier has a signed Bill of Lading acknowledging that the shipment has been received from SPX FLOW in good condition. SPX FLOW is not responsible for the collection of claims or replacement of materials due to transit shortage or damages. Warranty claims must have a Returned Material Authorization (RMA) from the Seller or returns will not be accepted. Contact or Claims for shortages or other errors must be made in writing to Seller within ten (10) days after delivery. This does not include transit shortage or damages. Failure to give such notice shall constitute acceptance and waiver of all such claims by Buyer. Page /017

7 Waukesha Cherry-Burrell Brand W0/W0 Valves Safety Safety READ AND UNDERSTAND THIS MANUAL PRIOR TO INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT SPX FLOW recommends users of our equipment and designs follow the latest Industrial Safety Standards. At a minimum, these should include the industrial safety requirements established by: 1. Occupational Safety and Health Administration (OSHA). National Fire Protection Association (NFPA) 3. National Electrical Code (NEC). American National Standards Institute (ANSI) WARNING Severe injury or death can result from electrical shock, burn, or unintended actuation of equipment. Recommended practice is to disconnect and lockout industrial equipment from power sources, and release stored energy, if present. Refer to the National Fire Protection Association Standard No. NFPA70E, Part II and (as applicable) OSHA rules for Control of Hazardous Energy Sources (Lockout-Tagout) and OSHA Electrical Safety Related Work Practices, including procedural requirements for: Lockout-tagout Personnel qualifications and training requirements When it is not feasible to de-energize and lockout-tagout electrical circuits and equipment before working on or near exposed circuit parts Before putting SPXFLOW equipment into operation, the operator shall analyze the application for all foreseeable risks, their likelihood to occur and the potential consequences of the identified risks as per ISO and ISO/IEC in their actual current version. Locking and Interlocking Devices: These devices should be checked for proper working condition and capability of performing their intended functions. Make replacements only with the original equipment manufacturer s OEM renewal parts or kits. Adjust or repair in accordance with the manufacturer s instructions. Periodic Inspection: Equipment should be inspected periodically. Inspection intervals should be based on environmental and operating conditions and adjusted as indicated by experience. At a minimum, an initial inspection within 3 to months after installation is recommended. Inspection of the electrical control systems should meet the recommendations as specified in the National Electrical Manufacturers Association (NEMA) Standard No. ICS 1.3, Preventative Maintenance of Industrial Control and Systems Equipment, for the general guidelines for setting-up a periodic maintenance program. Replacement Equipment: Use only replacement parts and devices recommended by the manufacturer to maintain the integrity of the equipment. Make sure the parts are properly matched to the equipment series, model, serial number, and revision level of the equipment. Warnings and cautions are provided in this manual to help avoid serious injury and/or possible damage to equipment: DANGER marked with a stop sign. Immediate hazards which WILL result in severe personal injury or death. WARNING marked with a warning triangle. Hazards or unsafe practices which COULD result in severe personal injury or death. marked with a warning triangle. Hazards or unsafe practices which COULD result in minor personal injury or product or property damage. 1/ Page 7

8 Care of Stainless Steel Waukesha Cherry-Burrell Brand W0/W0 Valves Care of Component Materials NOTE: SPX FLOW recommends the use of an FDA-approved anti-seize compound on all threaded connections. WARNING Failure to comply with the Care of Component Materials could lead to bodily injury. Stainless Steel Corrosion Corrosion resistance is greatest when a layer of oxide film is formed on the surface of stainless steel. If film is disturbed or destroyed, stainless steel becomes much less resistant to corrosion and may rust, pit or crack. Corrosion pitting, rusting and stress cracks may occur due to chemical attack. Use only cleaning chemicals specified by a reputable chemical manufacturer for use with stainless steel. Do not use excessive concentrations, temperatures or exposure times. Avoid contact with highly corrosive acids such as hydrofluoric, hydrochloric or sulfuric. Also avoid prolonged contact with chloride-containing chemicals, especially in presence of acid. If chlorine-based sanitizers are used, such as sodium hypochlorite (bleach), do not exceed concentrations of 10 ppm available chlorine, do not exceed contact time of 0 minutes, and do not exceed temperatures of 10 F (0 C). Corrosion discoloration, deposits or pitting may occur under product deposits or under gaskets. Keep surfaces clean, including those under gaskets or in grooves or tight corners. Clean immediately after use. Do not allow equipment to set idle, exposed to air with accumulated foreign material on the surface. Corrosion pitting may occur when stray electrical currents come in contact with moist stainless steel. Ensure all electrical devices connected to the equipment are correctly grounded. Elastomer Seal Replacement Following Passivation Passivation chemicals can damage product contact areas of this equipment. Elastomers (rubber components) are most likely to be affected. Always inspect all elastomer seals after passivation is completed. Replace any seals showing signs of chemical attack. Indications may include swelling, cracks, loss of elasticity or any other noticeable changes when compared with new components. Page /017

9 Waukesha Cherry-Burrell Brand W0/W0 Valves Introduction Introduction General Information For control top information, please refer to publication For additional product information, please see our website at product-literature. Information in this manual should be read by all personnel involved in installation, setup, operation and maintenance of W0/W0 valves. Always use installation tools and lubricants recommended by SPX FLOW. Waukesha Cherry-Burrell brand products are subject to intensive intermediate and final leakage and functional tests. W0/W0 Series valves meet 3-A and EHEDG standards for sanitation, design and style. Factory Inspection Each Waukesha Cherry-Burrell brand valve is shipped completely assembled, lubricated and ready for use. Models and Specifications Materials Product Wetted: ASTM 31L (UNS-S3103); (DIN-1.0) Non-Product: ASTM 30 (UNS-S3000); (DIN-1.301) Seat Material: Elastomers: Tef-Flow (standard) Tef-Flow P (optional) Tri Ring (optional) Metal (optional) Bonded (optional) FKM (standard) EPDM (optional) Equipment Serial Number Waukesha Cherry-Burrell brand valves are identified by a serial number found on the label on the actuator cylinder. 1/ Page 9

10 Introduction Operating Parameters Waukesha Cherry-Burrell Brand W0/W0 Valves Temperature Range The recommended operating temperature is determined by the material used for the seals. No special precautions are required for applications within a temperature range of 3 F to 10 F (0 C to C). For applications above 190 F ( C), clearances can be affected by excessive thermal expansion when the valve is installed in compact fabrications or manifolds. Valve bodies have thicker cross-sections than tubing, but thermal expansion can affect clearances in interconnecting piping sections. If operating below 3 F (0 C): Control air must have an appropriately low dew point. Valve stems must be protected from icing to ensure long working life for valve stem seals. Solenoid valves may not be used in the control module in room environments below 3 F (0 C) and over 10 F (0 C), as function cannot be guaranteed. Seal Compatibility Table 1: Seal Compatibility for FKM/EPDM Seals Thermal Range of Application Chemical Resistance Not compatible with Fluorelastomer (FKM) Seals 3 F to 37 F (0 C to 190 C) Silicone oil and grease Ozone, aging and weather resistant Oils and fats Aliphatic, chlorinated and aromatic hydrocarbons Superheated steam Formic and acetic acids EPDM Seals 0 F to 7 F (-1 C to 13 C) Silicone oil and grease Ozone, aging and weather resistant Hot water and steam up to 7 F (13 C) Many organic and inorganic acids Cleaning agents, soda and potassium alkalis Many polar solvents (alcohols, ketones, esters) Mineral oil products (oils, greases and fuels) Contact SPX FLOW Application Engineering for other fluid compatibility. FKM and EPDM seals comply with FDA regulations. Page /017

11 Waukesha Cherry-Burrell Brand W0/W0 Valves Introduction Seat Options Seat Type Maximum Temperature Application Standard Tef-Flow (TF) White in color 10 F ( C)* Standard seat of choice. General Purpose >90% of applications Standard Tri Ring (TR) EPDM, FKM Operation 0 F (137 C) EPDM Sterile 7 F (13 C) EPDM Operation 30 F (17 C) FKM Sterile (Consult Factory) FKM High Pressure Particulate EHEDG Optional Tef-Flow P (TFP) Gray in color 0 F (137 C) High Temperature High Pressure Over Pressure Valves Optional Metal (M) 37 F (190 C) High Pressure High Flow Particulate Optional Bonded (B) EPDM, FKM 30 F (110 C) Particulate For higher temperature applications than those listed, please consult factory. *Operating conditions such as flow rate and pressure must be considered when operating near maximum temperature rating. Pressure Ratings Standard Valve Size with pressure at: 1.0/1-1/.0-1/ * 70 F (0 C) 00 psi (3. bar) 0 psi (31 bar) 00 psi ( bar) 30 psi ( bar) 00 psi (1 bar) 10 psi (10 bar) 10 /10 F (71/ C) 37 psi ( bar) 30 psi ( bar) 300 psi (17 bar) 0 psi (17 bar) 10 psi (10 bar) 100 psi ( bar) 0 F (11 C) 0 psi (17 bar) 0 psi (17 bar) 00 psi (1 bar) 10 psi (10 bar) 1 psi (. bar) 7 psi ( bar) Optional High Pressure Adapter and Clamps Valve Size with pressure at: 1.0/1-1/.0-1/ * 70 F (0 C) 10 psi ( bar) 900 psi ( bar) 70 psi (9 bar) /10 F (71/ C) 110 psi (0 bar) psi (0 bar) 90 psi (7 bar) F (11 C) 1100 psi (7 bar) 30 psi (7 bar) * High pressure clamp is not available for 3", ", ". 0 psi ( bar) / Page 11

12 Installation Waukesha Cherry-Burrell Brand W0/W0 Valves Installation WARNING To avoid electrocution, ALL electrical work should be done by a registered electrician, following industrial safety standards and local codes. All power must be OFF and Locked Out during installation. When installing valves, ensure that no foreign materials (e.g. tools, screws, welding wire, lubricants, cloths, etc.) are enclosed in the system. Welding Instructions CAUTION Inspect each valve prior to installation. When using buttweld connections on two- and three-piece body valves, clamp connections MUST be used on one or more bodies to allow service to the body o-ring(s) after installation. W0/W0 valves with welded connections require the following before welding: 1. Remove the stem and actuator assembly. See Valve Removal on page 19.. Remove all seals from the body. 3. Weld the body into position, ensuring that the connection is free of tension and distortion.. Dissipate heat away from the valve body to prevent warping. Air Supply Install the valves using dry, filtered air. Lubrication is not required. If using lubricated air, refer to the solenoid manufacturer s specifications. Pipeline Support Install adequate supports to prevent strain on the fittings, valves, and equipment connections. F C G 1. Install supports at least every 10 feet (3 meters) on straight runs of piping (Figure 1, item C). D E. Install supports on both sides of the valves as close as possible to the connections (Figure 1, item D). 3. Install supports at each change of pipeline direction (Figure 1, item E and F).. For pipelines passing through walls, floors or ceilings, provide at least 1 inch ( mm) of clearance around the pipe to allow for expansion and contraction (Figure 1, item G). VA100-0 Figure 1: Pipeline Support Page /017

13 Waukesha Cherry-Burrell Brand W0/W0 Valves Installation Flow Direction Install the valves to close against the flow to prevent hammering. VA100-1c Flow Figure : Flow Direction W0 Stem Flush Adapter W0 Series valves utilize a stem flush adapter to provide a liquid or steam barrier around the valve stem. W0 valves are designed for 1. psi (1 bar) maximum flush pressure with 1/" (.3 mm) tube O.D. connections. 1/ Page 13

14 Operation Waukesha Cherry-Burrell Brand W0/W0 Valves Operation Air Connections Maintainable Actuators A NOTE: Actual air pressure values may vary depending on the valve size, actuator size, holding pressure requirements and spring selection. ", ", and " Air-to-Raise Air Pressure Range = minimum 0 psi to maximum 90 psi (min. 3. bar to max.. bar) 1/"-7 NPT Thread A. Vent B. Air In B VA100-10a Figure 3: ", ", and " Air-to-Raise B ", ", and " Air-to-Lower Air Pressure Range = minimum 0 psi to maximum 90 psi (min. 3. bar to max.. bar) 1/"-7 NPT Thread A. Vent B. Air In A Figure : ", ", and " Air-to-Lower A VA100-10b " Air-to-Raise, 3-Position Air Pressure Range = minimum 0 psi to maximum 90 psi (3. bar to. bar) 1/"-7 NPT Thread B A. Vent B. Full Air In C. 3-Position Air In C VA100-37a Figure : " Air-to-Raise, 3-Position Page /017

15 Waukesha Cherry-Burrell Brand W0/W0 Valves Operation B " Air-to-Lower, 3-Position C Air Pressure Range = minimum 0 psi to maximum 90 psi (3. bar to. bar) 1/"-7 NPT Thread A. Vent B. Full Air In C. 3-Position Air In A VA a Figure : " Air-to-Lower, 3-Position Adjustable-Spring Actuators C ", ", and " Air-to-Raise, Adjustable-Spring D E A A. Vent B. Air In C. Locknut Cover D. Adjustment Screw E. Stop Air Pressure Range = minimum 7 psi to maximum 90 psi (. bar to. bar) 1/"-7 NPT Thread B VA100-9 Figure 7: ", ", and " Air-to-Raise, Adjustable-Spring ", ", and " Air-to-Lower, Adjustable-Spring B Air Pressure Range = minimum 7 psi to maximum 90 psi (. bar to. bar) D E A A. Vent B. Air In C. Locknut Cover D. Adjustment Screw E. Stop 1/"-7 NPT Thread C VA100- Figure : ", ", and " Air-to-Lower, Adjustable-Spring 1/ Page 1

16 Operation Maintenance-Free Actuators Waukesha Cherry-Burrell Brand W0/W0 Valves A, B, and C Size Air-to-Raise, Maintenance-Free A B A. Vent B. Air In A, B and C Size Air Pressure Range = 7-10 psi (- bar) 1/" BSPP x 1/" OD Thread A, B, and C Size Air-to-Lower, Maintenance-Free A, B and C Size Air Pressure Range = 7-10 psi (- bar) 1/" BSPP x 1/" OD Thread NOTE: The actuator shown in Figure 9 is in air-to-raise configuration; if it is configured for air-to-lower, port A becomes Air In and port B becomes Vent. VA Figure 9: A, B and C Size Air-to-Raise, Maintenance-Free Page /017

17 Waukesha Cherry-Burrell Brand W0/W0 Valves Operation Pressure Setting Table : Spring Setting for Air-to- Raise, Adjustable-Spring Actuator Plug Size 1." 0 mm.0" 0 mm." mm 3.0" 0 mm.0" 100 mm Pressure change per turn of adjusting screw Actuator RHAR RHAR RHAR Air-To-Raise, Adjustable-Spring Actuator CAUTION Do not use vice-grips, channel locks, or pipe wrenches, as damage to the adjustment screw can result. Remove locknut cover (Figure 7). Using a 1 hex wrench or 1/ spanner, turn down the adjustment screw fully, until the stop contacts the actuator can (approx. -9 turns). This is the maximum holding pressure setting. Refer to publication DS-101, W0 Series Shut-Off & Divert Valves, for pressure holding charts for the actuator size and valve seat size: W1, W, W Air-to-Raise. NOTE: In some cases, the valve seat size may be less than the body size (reduced-seat options). Be sure to check holding pressures using the correct seat size and actuator diameter size. To reduce the pressure setting below the maximum, unscrew the adjustment screw as per Table. Check and confirm specific settings with a master gauge under pressure; adjust as required. Once the setting is achieved, apply a scribe line to the indicator stem to mark the position. Actual pressure change per turn of the adjusting screw may be different due to spring variations. Air-to-Lower, Adjustable-Spring Actuator CAUTION Do not use vice-grips, channel locks, or pipe wrenches, as damage to the adjustment screw can result. Table 3: Spring Setting for Air-to- Lower, Adjustable-Spring Actuator Plug Size.0" 0 mm." mm 3.0" 0 mm.0" 100 mm Pressure change per turn of adjusting screw Actuator RHAL RHAL RHAL Unscrew the locknut cover (Figure on page 1). The cover will stay in the yoke area. Using a 1" hex wrench or 1/" spanner, turn the adjustment screw in fully, until the stop contacts the actuator can (approx. -9 turns). This is the maximum holding pressure setting. Refer to publication DS-101, W0 Series Shut-Off & Divert Valves, for pressure holding charts for the actuator size and valve seat size: W3, W, W Air-to-Lower. NOTE: In some cases, the valve seat size may be less than the body size (reduced-seat options). Be sure to check holding pressures using the correct seat size and actuator diameter size. To reduce the pressure setting below the maximum, unscrew the adjustment screw as per Table 3. Check and confirm specific settings with a master gauge under pressure; adjust as required. Once the setting is achieved, apply a scribe line to the indicator stem to mark the position. Actual pressure change per turn of the adjusting screw may be different due to spring variations. 1/ Page 17

18 Maintenance Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Maintenance Intervals Maintain adequate stock of replacement parts. See the items in bold beginning on page for recommended spare parts. Maintenance intervals should be determined by the user and specific application, based on the following conditions: Inspection DANGER Do not put a hand into the yoke or body of a pneumatically actuated valve. Lubrication VA100-39a Daily operation period Switching frequency Application parameters such as temperature, pressure, and flow Product type Inspect the following on a regular basis: Actuator connections for air leaks Valve body and stem o-rings Valve seats (If leakage occurs, see Troubleshooting on page 7) Pneumatic connections: - Air pressure at supply connection - Air lines for kinks and leaks - Threaded connections for tight fit - Threaded stress relief for tight fit Electrical connections secure on the control module: - Wire connections tight on the terminal strip - Clean air filter at regular intervals. No lubrication is required other than as noted in the disassembly and assembly procedures. (Use food grade non-petroleum (silicone) grease on seals and o-rings.) Apply Bostik Never-Seez White Food Grade with PTFE or equivalent to all bolts and threaded stem parts. Cleaning NOTE: Actuate each valve a minimum of twice each cycle to ensure effective cleaning and sanitizing. CAUTION Avoid splashing any liquid into the air vent of the actuator during clean up. Cleaning-In-Place (CIP) CIP methods can be used to clean installed automatic valves without disassembly. Select methods based on the specific requirements of sanitarians and each application. Check with local chemical suppliers for the most effective cleaning agents and procedures. Page /017

19 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Valve Removal Before detaching the port connections on the valve body, perform the following: 1. Clean, rinse and drain the pipe system elements attached to the valve.. Remove or block the fluid and gas lines to prevent material from entering the pipe system elements attached to the valve. 3. Shut off the delivery of the control air unless it is required for the removal of the valve stem/actuator assembly from the body.. Disconnect the electrical supply and lockout all power.. If the valve has a control module with solenoid, the air and electric supply must remain ON until the valve is properly disassembled. 1/ Page 19

20 Maintenance W1/W1 Valve Disassembly B VA100-1b Figure 10: W1/W1 Shut Off Valve (Air-to-Raise Shown) 1 A 3,3a,3b, 3c,3d 7 Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Apply air to Port A to raise the stem.. Remove the body clamp (Figure 10, item ). 3. Release the air pressure.. Remove the body from the adapter (item 3). For two-piece bodies, un-clamp and remove the lower body first.. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve. 7. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke. 10. Remove the body o-ring (item ) and stem o-ring (item ); replace them as needed. 11. Inspect and replace the PTFE bearing (item ) as needed. Air-to-Lower Actuator 1. Shut off the air and disconnect the air line to the actuator at Port B.. For valves with control modules, disconnect/lockout the electrical power to the valve. 3. Remove the body clamp (item ) and body from the adapter (item 3). For two-piece bodies, un-clamp and remove the lower body first.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item7).. Replace the seat ring (item ) as needed. See Seat Replacement on page 37.. Unscrew the adapter (item 3) from the yoke. 7. Remove the body o-ring (item ) and stem o-ring (item ); replace them as needed.. Inspect and replace the PTFE bearing (item ) as needed. Page /017

21 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance W1/W1 Valve Assembly B 1 A 3,3a,3b, 3c,3d Air-to-Raise Actuator 1. Screw the adapter (Figure 11, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Apply air to Port A to raise the stem.. Assemble the body to the adapter; secure it with the body clamp (item ).. Release the air pressure. Air-to-Lower Actuator 1. Screw the adapter (item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Assemble the body to the adapter; secure it with the body clamp (item ). 7 VA100-1b Figure 11: W1/W1 Shut Off Valve (Air-to-Raise Shown) 1/ Page 1

22 Maintenance W1Y Valve Disassembly B 1 A 7 VA100-01a Figure 1: W1Y Shut Off Valve Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Apply air to Port A to raise the stem.. Remove the body clamp (Figure 10, item ). 3. Release the air pressure.. Remove the body from the adapter (item 3). For two-piece bodies, un-clamp and remove the lower body first.. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve. 7. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke. 10. Remove the body o-ring (item ) and stem o-ring (item ); replace them as needed. 11. Inspect and replace the PTFE bearing (item ) as needed. Air-to-Lower Actuator 1. Shut off the air and disconnect the air line to the actuator at Port B.. For valves with control modules, disconnect/lockout the electrical power to the valve. 3. Remove the body clamp (item ) and body from the adapter (item 3). For two-piece bodies, un-clamp and remove the lower body first.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item7).. Replace the seat ring (item ) as needed. See Seat Replacement on page 37.. Unscrew the adapter (item 3) from the yoke. 7. Remove the body o-ring (item ) and stem o-ring (item ); replace them as needed.. Inspect and replace the PTFE bearing (item ) as needed. Page /017

23 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance W1Y Valve Assembly A B 1 Air-to-Raise Actuator 1. Screw the adapter (Figure 11, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Apply air to Port A to raise the stem.. Assemble the body to the adapter; secure it with the body clamp (item ).. Release the air pressure. Air-to-Lower Actuator 1. Screw the adapter (item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Assemble the body to the adapter; secure it with the body clamp (item ). 7 VA100-01a Figure 13: W1Y Shut Off Valve 1/ Page 3

24 Maintenance W/W Valve Disassembly B VA100-b Figure 1: W/W Divert Valve (Air-to-Raise Shown) 1 A 3,3a, 3b,3d 7 9 Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Apply air to Port A to raise the stem.. Remove the lower body clamp (Figure 1, item ) and lower body. 3. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Remove the upper body clamp (item ) and upper body. 7. Replace the seat ring (item ) as needed. See Seat Replacement on page 37.. Unscrew the adapter (item 3) from the yoke. 9. Remove the body o-ring (item ) and stem o-ring (item ); replace them as needed. 10. Inspect and replace the PTFE bearing (item ) as needed. Air-to-Lower Actuator 1. Remove the lower body clamp (Figure 1, item ) and lower body (item 9).. Apply air to Port B to lower the stem. 3. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Shut off the air and disconnect the air line to the actuator.. Remove the upper body clamp (item ) and upper body.. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke.. Remove the body o-ring (item ) and stem o-ring (item ); replace them as needed. 9. Inspect and replace the PTFE bearing (item ) as needed. Page /017

25 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance W/W Valve Assembly B VA100-b Figure 1: W/W Divert Valve (Air-to-Raise Shown) 1 A 3,3a, 3b,3d 7 9 Air-to-Raise Actuator 1. Screw the adapter (Figure 1, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Apply air to Port A to raise the stem.. Install the lower body o-ring (item ). 7. Assemble the lower body; secure it with the lower body clamp (item ).. Release the air pressure. Air-to-Lower Actuator 1. Screw the adapter (item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Apply air to Port B to lower the stem.. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Release the air pressure. 7. Install the lower body o-ring (item ).. Assemble the lower body; secure it with the lower body clamp (item ). 1/ Page

26 Maintenance W3/W3 Valve Disassembly B VA100-3b Figure 1: W3/W3 Shut Off Valve (Air-to-Raise Shown) 1 A 3,3a, 3b,3d 7 9 Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Remove the lower body clamp Figure 1, item ) and the lower body (item 9).. Remove the body o-ring (item ); replace as needed. 3. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Replace the seat ring (item ) as needed. See Seat Replacement on page Remove the upper body clamp (item ) and the upper body from the adapter (item 3).. Unscrew the adapter (item 3) from the yoke. 9. Remove the body o-ring (item ) and stem o-ring (item ); replace as needed. 10. Inspect and replace the PTFE bearing (item ) as needed. Air-to-Lower Actuator 1. Remove the lower body clamp (Figure 1, item ) and the lower body (item 9).. Apply air to Port B to lower the stem. 3. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Release the air pressure.. Remove the upper body clamp (item ) and the upper body from the adapter (item 3).. Unscrew the adapter (item 3) from the yoke. 7. Remove the body o-ring (item ) and stem o-ring (item ); replace as needed. Page /017

27 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance W3/W3 Valve Assembly B VA100-3b Figure 17: W3/W3 Shut Off Valve (Air-to-Raise Shown) 1 A 3,3a, 3b,3d 7 9 Air-to-Raise Actuator 1. Screw the adapter (Figure 17, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ) and PTFE bearing (item ). 3. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Install the lower body o-ring (item ).. Assemble the lower body; secure it with the lower body clamp (item ). Air-to-Lower Actuator 1. Screw the adapter (item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ) and PTFE bearing (item ). 3. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Apply air to Port B to lower the stem.. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Release the air pressure. 7. Install the lower body o-ring (item ).. Assemble the lower body; secure it with the lower body clamp (item ). 1/ Page 7

28 Maintenance W/W Valve Disassembly 1 7 3,3a, 3b,3d A 1 Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve. 3. Remove the body/tank flange clamp (Figure 1, item ) and remove the valve from the tank flange.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Replace the seat ring (item ) as needed. See Seat Replacement on page 37.. Remove the lower body o-ring (item ); replace as needed. 7. Remove the upper body clamp (item ) and upper body from the adapter (item 3).. Unscrew the adapter (item 3) from the yoke. 9. Remove the upper body o-ring (item ) and stem o-ring (item ); replace as needed. 10. Inspect and replace the PTFE bearing (item ) as needed. B VA100-b Figure 1: W/W Tank Outlet Valve Air-to-Lower Actuator 1. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve. 3. Remove the body/tank flange clamp (Figure 1, item ) and remove the valve from the tank flange.. Reapply the air to the actuator.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Shut off the air and disconnect the air line to the actuator. 7. Remove the upper body clamp (item ) and upper body from the adapter (item 3).. Unscrew the adapter (item 3) from the yoke. 9. Remove the upper body o-ring (item ) and stem o-ring (item ); replace as needed. Page /017

29 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance W/W Valve Assembly 1 B VA100-b Figure 19: W/W Tank Outlet Valve 7 3,3a, 3b,3d A 1 Air-to-Raise Actuator 1. Screw the adapter (Figure 19, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Install the lower body o-ring (item ) onto the body.. Insert the valve into the tank flange and tighten the body clamp (item ). Air-to-Lower Actuator 1. Screw the adapter (Figure 19, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and PTFE bearing (item ). 3. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Apply air to Port B to lower the stem.. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Release the air pressure. 7. Install the lower body o-ring (item ) onto the body.. Insert the valve into the tank flange and tighten the body clamp (item ). 1/ Page 9

30 Maintenance WR/WR Valve Disassembly Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Remove the body/tank flange clamp (item ) and remove the valve from the tank flange ,3a, 3b,3d A 1. Apply air to Port A to raise the stem. 3. Remove the body clamp (item ).. Release the air pressure.. Remove the body from the adapter (item 3).. Shut off the air and disconnect the air line to the actuator. 7. For valves with control modules, disconnect/lockout the electrical power to the valve.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7). 9. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke. 11. Remove the body o-ring (item ) and stem o-ring (item ); replace as needed. 1. Inspect and replace the PTFE bearing (item ) as needed. Air-to-Lower Actuator B VA100-Ra Figure 0: WR/WR Tank Outlet Valve 1. Remove the body/tank flange clamp (Figure 0, item ) and remove the valve from the tank flange.. Shut off and disconnect the air line to the actuator. 3. For valves with control modules, disconnect/lockout the electrical power to the valve.. Remove the body clamp (item ) and body from the adapter (item 3).. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke.. Remove the body o-ring (item ) and stem o-ring (item ); replace as needed. 9. Inspect and replace the PTFE bearing (item ) as needed. Page /017

31 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance WR/WR Valve Assembly VA100-Ra Figure 1: WR/WR Tank Outlet Valve 7 3,3a, 3b,3d B 1 A 1 Air-to-Raise Actuator 1. Screw the adapter (Figure 1, item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and the PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Apply the air to Port A to raise the stem.. Assemble the body to the adapter (item 3); secure it with the body clamp (item ).. Release the air pressure. 7. Insert the valve into the tank flange and tighten the body clamp (item ). Air-to-Lower Actuator 1. Screw the adapter (item 3) onto the yoke.. Install the body o-ring (item ), stem o-ring (item ), and the PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Assemble the body to the adapter (item 3); secure it with the body clamp (item ).. Insert the valve into the tank flange and tighten the body clamp (item ). 1/ Page 31

32 Maintenance WET/WET Valve Disassembly Figure : WET Tank Outlet Valve Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve. 3. Remove the body/tank flange clamp (Figure, item ) and remove the valve from the tank flange.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Replace the seat ring (item ) as needed. See Seat Replacement on page 37.. Remove the lower body o-ring (item ); replace as needed. 7. Unscrew the body from the yoke.. Remove the stem o-ring (item ); replace as needed. 9. Inspect and replace the PTFE bearing (item ) as needed. Air-to-Lower Actuator 1. Shut off the air and disconnect the air line to the actuator.. For valves with control modules, disconnect/lockout the electrical power to the valve. 3. Remove the body/tank flange clamp (Figure, item ) and remove the valve from the tank flange.. Reapply the air to the actuator.. Using /-inch wrench flats on the stem, unscrew and remove the valve stem (item 7).. Shut off the air and disconnect the air line to the actuator. 7. Unscrew the body from the yoke.. Remove the stem o-ring (item ); replace as needed. 9. Inspect and replace the PTFE bearing (item ) as needed. Page /017

33 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance WET/WET Valve Assembly Air-to-Raise Actuator 1. Screw the body onto the yoke.. Install the stem o-ring (Figure 3, item ) and PTFE bearing (item ). 3. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Install the lower body o-ring (item ) onto the body.. Insert the valve into the tank flange and tighten the body clamp (item ). Air-to-Lower Actuator 1. Screw the body onto the yoke.. Install the stem o-ring (item ) and PTFE bearing (item ). 3. Apply air to Port B to lower the stem.. Using /-inch torque wrench flats on the stem, install the valve stem (item 7). Torque to 30 in/lbs.. Release the air pressure.. Install the lower body o-ring (item ) onto the body. 7. Insert the valve into the tank flange and tighten the body clamp (item ). Figure 3: WET Tank Outlet Valve 1/ Page 33

34 Maintenance W/W Valve Disassembly 9 7b Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Remove the lower body clamp (Figure, item ) and the lower body.. Remove the body o-ring (item ); replace as needed. 3. If necessary, remove the lower bearing carrier (item 11) from the lower body. Figure - Remove Counter bore O-ring B VA100-39b. Remove the body o-ring (item ) and stem o-ring (item ) from the bearing carrier; replace as needed.. Inspect and replace the PTFE bearing (item ) as needed.. Using /-inch wrench flats on the stem, unscrew and remove the lower valve stem (Figure, item 7b). 7. Replace the o-ring (Figure, item 9) in the counter bore of the lower stem as needed. 1. Replace the lower seat ring (Figure, item ) as needed. See Seat Replacement on page 37. 7b A 3,3a, 3b,3d 7a 9. Remove the middle body clamp (item ) and the middle body. 10. Remove the middle body o-ring (item ); replace as needed. 11. Apply air to Port A to raise the stem. 1. Remove the upper body clamp (item ) and the upper body from the adapter (item 3). 13. Using /-inch wrench flats on the stem, unscrew and remove the upper valve stem (item 7a). 1. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke. 1. Remove the body o-ring (item ) and stem o-ring (item ) from the adapter; replace as needed. 17. Inspect and replace the PTFE bearing (item ) as needed. 11,11a,11b,11d VA100-b Figure : W/W Divert Valve Page /017

35 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Air-to-Lower Actuator B 1. Remove the lower body clamp (Figure, item ) and the lower body.. Remove the body o-ring (item ); replace as needed. 7b 1 A 3,3a, 3b,3d 7a 3. If necessary, remove the lower bearing carrier (item 11) from the lower body.. Remove the body o-ring (item ) and stem o-ring (item ) from the bearing carrier; replace as needed.. Inspect and replace the PTFE bearing (item ) as needed.. Apply air to Port B to lower the stem. 7. Using /-inch wrench flats on the stem, unscrew and remove the lower valve stem (Figure, item 7b).. Replace the o-ring (Figure, item 9) in the counter bore of the lower stem as needed. 9. Replace the lower seat ring (Figure, item ) as needed. See Seat Replacement on page Release the air pressure. 11. Shut off the air and disconnect the air line to the actuator. 1. For valves with control modules, disconnect/lockout the electrical power to the valve. 13. Remove the middle body clamp (item ) and the middle body. 11,11a,11b,11d VA100-b Figure : W/W Divert Valve 1. Remove the middle body o-ring (item ); replace as needed. 1. Remove the upper body clamp (item ) and the upper body from the adapter (item 3). 1. Using /-inch wrench flats on the stem, unscrew and remove the upper valve stem (item 7a). 17. Replace the seat ring (item ) as needed. See Seat Replacement on page Unscrew the adapter (item 3) from the yoke. 19. Remove the body o-ring (item ) and stem o-ring (item ) from the adapter; replace as needed. 0. Inspect and replace the PTFE bearing (item ) as needed. 1/ Page 3

36 Maintenance W/W Valve Assembly B Waukesha Cherry-Burrell Brand W0/W0 Valves Air-to-Raise Actuator 1. Screw the adapter (Figure, item 3) onto the yoke.. Install the upper body o-ring (item ) onto the adapter. 3. Using /-inch torque wrench flats on the stem, install the upper valve stem (item 7a). Torque to 30 in/lbs. 1. Apply air to Port A to raise the stem.. Assemble the upper body to the adapter; secure it with the upper body clamp (item ). A 3,3a, 3b,3d. Install the middle body o-ring (item ) onto the upper body. 7. Assemble the middle body; secure it with the middle body clamp (item ).. Release the air pressure. 9. Using /-inch torque wrench flats on the stem in the yoke area, install the lower valve stem (item 7b) onto the upper stem (item 7a). Torque to 30 in/lbs. 10. Install the lower body o-ring (item ) on the middle body. 7a 11. Assemble the lower body; secure it with the lower body clamp (item ). 1. Install the body o-ring (item ) onto the bearing carrier and insert it into the lower body. 7b 13. Install the bearing carrier clamp (item ). 11,11a,11b,11d VA100-b Air-to-Lower Actuator 1. Screw the adapter (Figure, item 3) onto the yoke. Figure 7: W/W Divert Valve. Install the upper body o-ring (item ) onto the adapter. 3. Using /-inch torque wrench flats on the stem, install the upper valve stem (item 7a). Torque to 30 in/lbs.. Assemble the upper body to the adapter; secure it with the upper body clamp (item ).. Install the middle body o-ring (item ) onto the upper body.. Assemble the middle body; secure it with the middle body clamp (item ). 7. Apply air to Port B to lower the stem.. Install the o-ring (item 9) in the counter bore of the lower stem (item 7b). 9. Using /-inch torque wrench flats on the stem in the yoke area, install the lower valve stem (item 7b). Torque to 30 in/ lbs. 10. Install the lower body o-ring (item ) on the middle body. 11. Assemble the lower body; secure it with the lower body clamp (item ). 1. Release the air pressure. 13. Install the body o-ring (item ) onto the bearing carrier (item 11) and insert it into the lower body. 1. Install the bearing carrier clamp (item ). Page /017

37 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Seat Replacement Standard Tef-Flow Seat Standard Tef-Flow seats are white and can be cut for removal. E A B C 1. Place a piece of shim stock or a feeler gauge behind the seat ring (Figure, item C) to prevent scratching the stem surface.. Carefully cut through the seat ring with a utility knife. 3. Remove the seat ring (item C) from the stem (item A).. To install a new seat, place the seat ring on a standard S- Line ferrule (item D) equal in size to the valve, or on the seat ring tool as shown in Figure, item E.. Align the stem on the seat ring and apply pressure to snap the seat into place.. The valve seat will spin freely when properly installed. VA100-17b A. Stem B. Stem Groove E. Seat Ring D C. Seat Angle D. "S" Clamp Ferrule Figure : Tef-Flow Seat A D Tef-Flow P Seat Tef-Flow P seats are gray and must be melted through for proper removal. 1. Melt through the seat ring using a clean plastic cutting tip on a heavy-duty soldering iron capable of maintaining a 700 F (371 C) tip temperature. B C Figure 9: Tef-Flow P Seat VA CAUTION Do not use a knife to cut the seat ring from the stem to avoid personal injury and/or damage to the stem.. To install a new seat, place the installation tool base onto a table or bench with a 1.0" ( mm) hole (Figure, item B). For tool part numbers, see Installation Tools on page. 3. Place the stem through the hole in the base.. Place a new seat ring (item C) onto the stem with the seat angle (item D) and flat side facing away from the base as shown in Figure.. Place the seat ring tool (Figure, item A) over the seat ring. For tool part numbers, see Installation Tools on page.. Using an arbor press, apply a constant steady pressure to the seat ring tool, snapping the seat ring into place. CAUTION DO NOT use a hammer to install. 7. The valve seat will spin freely when properly installed. 1/ Page 37

38 Maintenance Waukesha Cherry-Burrell Brand W0/W0 Valves Standard Tri Ring Seat 1. Remove the Tri Ring seat by carefully cutting or using an o- ring tool or pick to pull the seat out of the groove. Do not scratch or nick the metal seating surface.. Clean the Tri Ring groove after removing the seat. 3. Lubricate the new Tri Ring (Figure, item A) with acceptable cleansing solution or lubricant.. Place the stem through a 1-1/ inch (30 mm) hole bored through a board, or secure it with a vise with copper or aluminum jaws.. Start the Tri Ring as shown in Figure 9.. Using the installation tool, part number (Figure 9, item B), press the Tri Ring into the plug at locations A, B, C, and D (Figure 30). If this tool is not available, a dull, flat tool can be used. DO NOT use a knife or any other sharp item that will tear or cut the Tri Ring. 7. To finish installation, press small sections of the seal, alternating from side to side (A-B-C-D), avoiding large loops of seal.. When properly installed, the Tri Ring seat lip will protrude slightly from the seat edge as shown in Figure 9. A B VA100-0a Figure 30: Installing New Tri Ring Seat B C A D Bonded Seat Stems Bonded seat stems do not require maintenance. If the seating surface becomes damaged, purchase a new seat stem. Metal Seat Stems Figure 31: Pressing Tri Ring Into Plug VA100-0a Metal seat stems do not require maintenance. If the seating surface becomes damaged, purchase a new seat stem. Do not attempt to re-lap or machine the seating surfaces. Page /017

39 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Servicing Actuators: U-cups, O-rings and Bearings Shut off the air and disconnect the air supply line to the actuator. Disconnect/lockout the electrical power to the valve. Valves with Control Module For control top information, please refer to publication For additional product information, please see our website at spxflow.com/en/waukesha-cherry-burrell/resources/productliterature/. For the Set and Forget Switch option, remove the target on the indicator stem before removing the actuator can. 9 Figure 3: Remove Yoke 1 Figure 33: Remove Yoke O-ring and Guide Bearing 1 VA100-3a 7 9 VA100-37a O-ring and Bearing Replacement:,, and " Actuator 1. Remove the cap screws (Figure 3, item 9) and pull the yoke (item 1) from the actuator cylinder (item ).. Remove the yoke (Figure 33, item ). Inspect the lower stem o-ring (item ) and cylinder o-ring seals (item 7). 3. Remove the worn o-ring seals. Coat the new o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent, and replace them.. Remove the PTFE guide bearing (Figure 33, item ) by placing a screwdriver behind the bearing to pry it away from the wall of the yoke. Use needle-nose pliers to grip and remove the bearing.. Pull the lower stem (Figure 3, item 3) to remove the caged spring assembly from the actuator cylinder. DANGER Do not use air to remove the caged spring assembly.. Remove and inspect the upper stem o-ring (Figure 3, item ) in the top of the actuator cylinder. 3 VA a Figure 3: Pull Lower Stem 7. Remove the worn o-ring seals. Coat the new o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent, and replace them.. Inspect and replace the PTFE guide bearing (Figure 3, item ) in the actuator cylinder as needed. VA100-3 Figure 3: Remove O-ring and Bearing 1/ Page 39

40 Maintenance Waukesha Cherry-Burrell Brand W0/W0 Valves 1,1a 13 U-cup Replacement: " and " Actuator 1. Inspect the piston U-cup seal (Figure 3, item ).. Remove the worn U-cup seal. Do not score or nick grooves in the piston (item 10). 7 3 VA Figure 3: " and " Actuator Coat the new U-cup seal with Dow Corning #7 Silicone Lubricant or equivalent.. Slightly stretch the lubricated seal to fit over the piston. Install the lower seal first with the "U" pointing down. Install the upper seal with the "U" pointing up. U-cup seals flare slightly at the outer edges when they are properly installed.. Place the piston and spring assembly in the cylinder.. Place the cylinder over the yoke, and install cap screws (item 9) to secure it. NOTE: If the stems were disassembled during this maintenance procedure, clean, prime, and apply Loctite 0 Thread Locker, according to manufacturer s specifications, to the upper (items 1, 1a) and lower (item 3) stems. Torque the stems to 00 in/lbs. 13 1,1a O-ring and Bearing Replacement: Actuator 1. Inspect the piston o-ring seal (Figure 37, item ).. Remove the worn o-ring seal. Do not score or nick grooves in the piston (item 10). 3. Coat the new o-ring seal with Dow Corning #7 Silicone Lubricant or equivalent. 10. Slightly stretch the lubricated seal to fit over the piston VA Inspect and replace the PTFE guide bearing (item 1) on the piston as needed.. Place the piston and spring assembly in the cylinder. 7. Place the cylinder over the yoke, and install cap screws (item 9) to secure it. NOTE: If the stems were disassembled during this maintenance procedure, clean, prime, and apply Loctite 0 Thread Locker, according to manufacturer s specifications, to the upper (items 1, 1a) and lower (item 3) stems. Torque the stems to 00 in/lbs. Figure 37: " Actuator Page /017

41 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance ,1a VA Figure 3: " Air-to-Raise 3-Position Actuator U-cup, O-ring and Bearing Replacement: Air-to-Raise 3-Position Actuator 1. Inspect the upper piston U-cup seal (Figure 3, item ).. Remove the worn U-cup seal. Do not score or nick grooves in the piston (item 10). 3. Coat the new U-cup seal with Dow Corning #7 Silicone Lubricant or equivalent.. Slightly stretch the lubricated seal to fit over the upper piston. Install the lower seal first with the "U" pointing down. Install the upper seal with the "U" pointing up. U-cup seals flare slightly at the outer edges when properly installed.. Inspect the lower piston o-ring (item 0), stem o-ring (items and 11) and yoke o-ring seals (item 7).. Remove the worn o-ring seals. Do not score or nick grooves in the piston (item 1). 7. Coat the new o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent.. Slightly stretch the lubricated piston seal to fit over the lower piston. 9. Inspect and replace the PTFE guide bearings (items 1 and ) as needed. 10. Place the outer stem (item 1) in the lower piston. 11. Screw the outer stem into the yoke (item 1). 17 turns = full stroke adjustment 1 turn = 0.03 stroke Using a spanner wrench, turn the stem counter-clockwise for more stroke and clockwise for less stroke. 1. Place the piston and spring assembly in the cylinder. 13. Place the cylinder over the yoke, and install cap screws (item 9) to secure it. NOTE: If the stems were disassembled during this maintenance procedure, clean, prime, and apply Loctite 0 Thread Locker, according to manufacturer s specifications, to the upper (items 1, 1a) and lower (item 3) stems. Torque the stems to 00 in/lbs. 1/ Page 1

42 Maintenance VA Figure 39: " Air-to-Lower 3-Position Actuator Waukesha Cherry-Burrell Brand W0/W0 Valves U-cup, O-ring and Bearing Replacement: Air-to-Lower 3-Position Actuator 1. Inspect the lower piston U-cup seal (Figure 39, item ).. Remove the worn U-cup seal. Do not score or nick grooves in the piston (item 10). 3. Coat the new U-cup seal with Dow Corning #7 Silicone Lubricant or equivalent.. Slightly stretch the lubricated seal to fit over the lower piston. Install the lower seal first with "U" pointing down. Install the upper seal with the "U" pointing up. U-cup seals flare slightly at the outer edges when properly installed.. Inspect the stem o-ring seal (item ).. Remove the worn o-ring seal. Do not score or nick grooves in the piston. 7. Coat the new o-ring seal with Dow Corning #7 Silicone Lubricant or equivalent.. Slightly stretch the lubricated seal to fit over the lower piston. 9. Inspect and replace the PTFE guide bearing (item ) on the piston as needed. 10. Connect the piston and spring assembly to the stem (item 3) with the bolt (item 1). 11. Assemble the piston and spring assembly to the yoke (item 1). 1. Inspect the upper piston U-cup seal (item 17). 13. Remove the worn U-cup seal. Do not score or nick grooves in the piston (item 1). 1. Coat the new U-cup seal with Dow Corning #7 Silicone Lubricant or equivalent. 1. Slightly stretch the lubricated seal to fit over the upper piston. Install the lower seal first with the "U" pointing down. Install the upper seal with the "U" pointing up. U-cup seals flare slightly at the outer edges when properly installed. 1. Inspect the upper stem o-ring seal (item 11). 17. Remove the worn o-ring seal. Do not score or nick grooves in the cylinder top and upper piston. 1. Coat the new o-ring seal with Dow Corning #7 Silicone Lubricant or equivalent. 19. Install the lubricated seal in the upper piston and cylinder top. 0. Assemble the upper piston and stem (item 1) to the cylinder. Secure them with a hex nut (item 1). Place the cylinder over the yoke, and install cap screws (item 9) to secure it. 1. Adjust the mid-position by loosening the hex nut (item 1) and turning the stem (item 1). NOTE: If the stems were disassembled during this maintenance procedure, clean, prime, and apply Loctite 0 Thread Locker, according to manufacturer s specifications, to the upper (item 1) and lower (item 3) stems. Torque the stems to 00 in/lbs. Page /017

43 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance 3 1c 1a 1b 1b 1a 1 1 O-ring and Bearing Replacement: Maintenance-Free Actuator 1. Remove the actuator from the valve assembly: a. Remove the control top. b. Remove the retaining nut and spacer located on top of the actuator. c. Unclamp the valve body and remove the body and stem. d. Un-bolt the yoke from the bottom of the actuator assembly.. Remove the o-ring guide nut assembly (Figure 0, item 1) from both ends of the actuator. 3. Replace the bearing (item 1c) and o-ring (1b). NOTE: Apply a thick layer of silicone lubricant on the o-ring prior to installation.. Re-install the o-ring guide nut assembly (Figure 0, item 1) and tighten the guide nut (item 1a) until it is snug. NOTE: Do not over-tighten the nut ("snug" is all that is required).. Reassemble the valve in reverse order of the items in step 1 above. 1c VA Figure 0: Maintenance-Free Actuator 1/ Page 3

44 Maintenance Waukesha Cherry-Burrell Brand W0/W0 Valves O-ring and Bearing Replacement:,, and " Adjustable-Spring Actuator WARNING Adjustable-Spring actuators cannot be disassembled. Do not attempt to cut the actuator or otherwise disassemble it, as the compressed spring will present a projectile hazard. Adjustable-spring actuators are fully welded and cannot be disassembled or reversed. Only compressed air side seals and bearings require maintenance. Air-to-Raise, Adjustable-Spring Actuator 1. Remove the valve from the body.. Shut off the air and disconnect the air supply line to the actuator. 3. Disconnect/lockout the electrical power to the valve. WARNING For Adjustable-Spring actuators, unload the spring adjustment completely before attempting to service the actuator VA Figure 1: ", ", and " Air-to-Raise, Adjustable-Spring Actuator 0 NOTE: On the " design, the location of items 11 and 1 is reversed (see inset).. Unscrew and remove the locknut cover (Figure 1, item 17). Unscrew and remove the adjustment screw (item 0). Check for free movement of the stem to ensure that no compression remains.. nspect the o-ring (item ) in the adjustment screw (item 0). Remove the worn o-ring seals. Coat the new o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent, and replace them.. Remove the PTFE guide bearing (item ) in the adjustment screw by placing a screwdriver behind the bearing to pry it away from the wall of the yoke (item 1). Use needle-nose pliers to grip and remove the bearing. 7. Using wrenches on the upper and lower wrench flats, unscrew and remove the lower stem (item 3). Do not remove the upper stem (item 1), as it locates an internal support washer.. Remove and inspect the yoke area stem o-ring (item 11). Remove the worn o-ring seal. Coat the new o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent, and replace them. 9. Inspect and replace the PTFE guide bearing (item 1) in the yoke as needed. 10. Reassemble the actuator in reverse order. 11. Once secure, screw in the adjustment screw (item 0) until it is held by threads (not in its final position). Refer to Adjustable-Spring Actuators: Pressure Setting (Table on page 17) for setting it to the desired loading pressure. Page /017

45 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Air-to-Lower, Adjustable-Spring Actuator 1. Remove the valve from the body.. Shut off the air and disconnect the air supply line to the actuator. 3. Disconnect/lockout the electrical power to the valve. WARNING For Adjustable-Spring actuators, unload the spring adjustment completely before attempting to service the actuator.. Using wrenches on the upper and lower wrench flats, unscrew and remove the upper stem (Figure, item 1). Do not remove the lower stem (item 3) as it locates an internal support washer.. Remove and inspect the indicator area stem o-ring (item ). Remove the worn o-ring seal. Coat the new o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent, and replace them.. Inspect and replace the PTFE guide bearing (item ) in the indicator area as needed. 7. Reassemble the actuator in reverse order.. Once secure, screw in the adjustment screw (item 0) until it is held by threads (not in its final position). Refer to Adjustable-Spring Actuators: Pressure Setting (Table 3 on page 17) for setting it to the desired loading pressure. VA100-1 Figure : ", ", and " Air-to-Lower, Adjustable-Spring Actuator 1/ Page

46 Maintenance Reversing the Spring Action on the Maintenance-Free Actuator Waukesha Cherry-Burrell Brand W0/W0 Valves 1. Remove the control top (if applicable).. Loosen and remove the retaining nut and spacer from the stem on the top of the actuator. 3. Loosen and remove the bolts on the yoke that are threaded into the bottom of the actuator.. Lift the actuator cylinder from the yoke/stem.. Flip the actuator cylinder over and re-insert the stem into the actuator.. Re-install the yoke bolts on the bottom of the actuator. 7. Install the spacer and retaining nut on top of the actuator.. Install the control top (if applicable). VA100-7 Figure 3: Maintenance-Free Actuator - reversing spring action Page /017

47 Waukesha Cherry-Burrell Brand W0/W0 Valves Maintenance Reversing the Spring Action on the Maintainable Actuator 1. Remove the cap screws (Figure, item 9) and pull the yoke (item 1) from the actuator cylinder (item ).. Pull the lower stem (Figure, item 3) to remove the caged spring assembly from the actuator cylinder. 10 Figure : Remove Yoke 3 VA100-39a Air-to-Raise Figure : Remove Actuator Stem Halves Figure : Pull Lower Stem VA b Air-to-Lower Figure 7: Actuator Piston/ Spring Configuration 3. Using a /-inch wrench on the lower stem (Figure, item 3) and a 3/-inch wrench on the upper stem (item ), unscrew and remove the two actuator stem halves.. Turn the piston/spring assembly (item 10) over.. Install the actuator stem halves in the piston/spring assembly. See Figure for Air-to-Raise configuration; Figure 7 for Air-to-Lower configuration. Clean, prime and apply Loctite 0 Thread Locker, according to manufacturer s specifications, to the upper (items 1, 1a) and lower (item 3) stems (See Figure 3 and Figure 37 on page 0). Torque the stems to 00 in/lbs for " and " actuators; 00 in/lbs for " actuators.. Coat the U-cup and o-ring seals with Dow Corning #7 Silicone Lubricant or equivalent. 7. Install the piston/spring assembly in the actuator cylinder and assemble them with cap screws (Figure, item 9).. Reverse the vent plug (Figure, item 13) as follows: Air-to-Raise Actuator: The vent plug must be located on TOP of the actuator in Port B (Figure, item B). Air-to-Lower Actuator: The vent plug must be located on the SIDE of the yoke in Port A (Figure, item A). Figure : Cap Screws and Vent Plug 1/ Page 7

48 Parts Lists Waukesha Cherry-Burrell Brand W0/W0 Valves Parts Lists W1/W1 Shutoff Valve 1 3,3a,3b,3c,3d 7 10 (3a) (3b) a (3c) VA100-1 (3d) Page /017

49 Waukesha Cherry-Burrell Brand W0/W0 Valves Parts Lists W1/W1 Shutoff Valve Item # Part Description 1" & 1-1/" " -1/" 3" " " Notes Control Top Contact Factory 1 Actuator See actuator parts list * Bearing Adapter, W0 (Std.) a Adapter, W POA High Press. W POA 3b Adapter, W c Adapter, W1A POA 3 3d Adapter, Wiping Stem Seal POA 1 * O-ring EPDM E7010 E701 FKM V7010 V701 * a Wiping EPDM POA Stem Seal FKM 11+ POA 1 Clamp Standard High Pressure POA * O-ring, EPDM E703 E70 E703 E703 E70 E70 Body FKM V703 V70 V703 V703 V70 V70 7 Stem (less Tef-Flow TM N/A seat ring) Tri Ring Metal P.O.A * Seat Ring Tef-Flow TM POA Tef-Flow TM P POA Tri Ring, EPDM Tri Ring, FKM High Pressure Backup Ring BURT10 POA PL07-CH1 Notes: * Recommended Spare Parts 1. Wiping Stem Seal Adapter and Wiping Stem Seal options available for W0 Series valves only.. W0 Adapter allows for liquid or steam flush of stem o-ring only. 3. W1A Adapter allows for liquid or steam flush of stem o-ring and body o-ring. Only available on one-piece body configurations.. High Pressure Body Clamp only required for valves equipped with High Pressure Adapter (item 3a).. W1A Adapter requires two body o-rings. POA: Contact Factory 1/ Page 9

50 Parts Lists Waukesha Cherry-Burrell Brand W0/W0 Valves W1Y Shutoff Valve 1 7 a (3d) VA Page /017

51 Waukesha Cherry-Burrell Brand W0/W0 Valves Parts Lists W1Y Shutoff Valve Item # Part Description -1/" 3" " Notes 1 Actuator See actuator parts list * Bearing Adapter, W0 (Std.) d Adapter, Wiping Stem Seal * O-ring EPDM FKM E701 V701 * a Wiping Stem Seal EPDM FKM Clamp Standard * O-ring, Body EPDM E701 E70 E707 FKM V701 V70 V707 7 Stem (less seat ring) Tef-Flow TM * Seat Ring Tef-Flow TM Tef-Flow TM P PL07-CH Notes: * Recommended Spare Parts 1. Tef-Flow P seat is not recommended for manual actuation configuration; Standard Tef-Flow seats should be used with manual actuation. 1/ Page 1

52 Parts Lists Waukesha Cherry-Burrell Brand W0/W0 Valves W/W Divert Valve 1 3,3a,3b,3d 7 10 (3a) (3b) (3d) a VA100- Page /017

53 Waukesha Cherry-Burrell Brand W0/W0 Valves Parts Lists W/W Divert Valve Item # Part Description 1" 1-1/" " -1/" 3" " Notes Control Top Contact Factory 1 Actuator See actuator parts list * Bearing Adapter, W0 (Std.) a Adapter, High W N/A Pressure W N/A 3b Adapter, W d Adapter, Wiping Stem Seal * O-ring EPDM FKM E7010 V7010 * a Wiping Stem EPDM Seal FKM 11+ Clamp Standard High Pressure N/A 3 * O-ring, Body EPDM E703 E70 E703 E703 E70 FKM V703 V70 V703 V703 V70 7 Stem (less seat ring) Tef-Flow TM Tef-Flow TM Long Stroke N/A N/A N/A Tri Ring Tri Ring, Long Stroke N/A N/A N/A Metal Metal, Long Stroke N/A N/A N/A * Seat Ring Tef-Flow TM Tef-Flow TM P Tri Ring, EPDM Tri Ring, FKM High Pressure Backup Ring BURT10 N/A PL07-CH3 * Recommended Spare Parts 1. Wiping Stem Seal Adapter and Wiping Stem Seal options available for W0 Series valves only.. W0 Adapter allows for liquid or steam flush of stem o-ring only. 3. High Pressure Body Clamp only required for valves equipped with High Pressure Adapter (item 3a). 1/ Page 3

54 Parts Lists Waukesha Cherry-Burrell Brand W0/W0 Valves W3/W3 Reverse Shutoff Valve 1 3,3a,3b,3d 7 10 a (3a) (3b) (3d) VA100-3 Page /017

55 Waukesha Cherry-Burrell Brand W0/W0 Valves Parts Lists W3/W3 Reverse Shutoff Valve Item # Part Description 1" & 1-1/" " -1/" 3" " " Notes Control Top Contact Factory 1 Actuator See actuator parts list * Bearing Adapter, W0 (Std.) a Adapter, W N/A High W N/A 3b Adapter, W d Adapter, Wiping Stem Seal P.O.A. 1 * O-ring EPDM E7010 E701 FKM V7010 V701 * a Wiping EPDM P.O.A. Stem Seal FKM 11+ P.O.A. 1 Clamp Standard High Pressure N/A 3 * O-ring, Body EPDM E703 E70 E703 E703 E70 E70 FKM V703 V70 V703 V703 V70 V70 7 Stem (less seat ring): Tef-Flow TM N/A Tef-Flow TM Long Stroke N/A N/A N/A Tri Ring Tri Ring, Long Stroke N/A N/A P.O.A. Metal P.O.A. Metal, Long Stroke N/A N/A P.O.A. * Seat Ring Tef-Flow TM N/A Tef-Flow TM P N/A Tri Ring, EPDM Tri Ring, FKM High Pressure Backup Ring BURT10 N/A Notes: * Recommended Spare Parts 1. Wiping Stem Seal Adapter and Wiping Stem Seal options available for W0 Series valves only.. W0 Adapter allows for liquid or steam flush of stem o-ring only. 3. High Pressure Body Clamp only required for valves equipped with High Pressure Adapter (item 3a). PL07-CH 1/ Page

56 Parts Lists Waukesha Cherry-Burrell Brand W0/W0 Valves W/W Tank Outlet Valve 1 7 3,3a,3b,3d 1 a 10 (3a) (3b) (3d) VA100- Page /017