Installation Instructions
|
|
- Wilfrid Gordon
- 6 years ago
- Views:
Transcription
1 page 1 of 9 Description The mount is designed to attach the antenna to a vertical tower pipe of diameter 115mm. The mount also provides adjustment ranges of ±15 fine elevation and ±180 ( ±12 fine) azimuth. Notice The installation, maintenance, or removal of antenna systems requires qualified, experienced personnel. Andrew installation instructions have been written for such personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. Andrew disclaims any liability or responsibility for the results of improper or unsafe installation practices. 3 NOTICE READ THE INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY FULLY ASSEMBLED ANTENNAS 1 2 MATERIAL CHECK Unpack all materials and inspect for any shipment damage. TIGHTENING OF HARDWARE. It is recommended that all hardware is tightened to the torques specified in Table 1. The integrity of the mount depends on all fasteners being properly tightened. TABLE 1. FASTENER TORQUE SPECIFICATIONS FASTENER TORQUE VALUES IN Nm (lb.ft) FOR EACH FASTENER SIZE (UNLESS OTHERWISE STATED. SIZE M5 M6 M8 M10 M12 M16 STAINLESS STEEL GALVANISED STEEL 4.5 (3.3) 2.7 (2) 7.7 (5.7) 4.5 (3.3) 18.7 (13.8) 11.1 (8.1) 39.2 (28.9) 22 (16.2) 65.1 (48) 38 (28) 161 (18.7) 95 (70.1) Warning: Use protective wear to avoid skin contact with the conductive grease. Keep away from mouth. Wash thoroughly after use with liberal amounts of liquid soap and rinse with water. Do not store open near food or food sources. Contents: oil, clay, and zinc dust. TO HOIST ANTENNA ATTACH M12 LIFTING EYE (NOT SUPPLIED) STANDARD VERSION ANTENNA INTEGRATED VERSION ANTENNA MOUNT SHOWN FULLY ASSEMBLED TO A 6ft ANTENNA (NOTE DIFFERENT STRUT PIPE ARRANGEMENT). is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
2 page 2 of 9 4 MOUNT POSITION RHS / LHS TO CHANGE ANTENNA FROM LEFT TO RIGHT HAND SIDE - ROTATE REFLECTOR ASSY 180 SO THAT THICK BRACKET IS BEING ATTACHED TO MOUNT ASSEMBLY. THICK BRACKET (3x BOLTS + NUTS) THIN BRACKET (2x BOLTS + NUTS) THICK BRACKET (3x BOLTS + NUTS) MOUNT ASSEMBLED ON RIGHT HAND SIDE THIN BRACKET (2x BOLTS + NUTS) MOUNT ASSEMBLED ON LEFT HAND SIDE is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
3 page 3 of 9 5 ATTACH SAFETY BRACKET. TORQUE TO 95Nm 6 ATTACH PANNING FRAME ASSEMBLY. TORQUE TO 95Nm is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
4 7 ATTACH ELEVATION ADJUSTERS. page 4 of 9 ELEVATION ADJUSTER (ENSURE ELEVATION ADJUSTER IS ATTACHED AT TOP OF MOUNT AS SHOWN) APPLY CONDUCTIVE GREASE TO THREADS OF ELEVATION ADJUSTER. 8 ATTACH REFLECTOR ASSEMBLY. DO NOT ATTACH MOUNT TO 'THIN' BRACKET is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
5 page 5 of 9 9 ATTACH STRUT PIPE. NOTE STRUT TO BE LOOSELY FITTED UNTIL ALIGNMENT IS COMPLETE THEN TIGHTEN ALL FIXINGS TO TORQUE SPECIFIED. STRUT PIPE ATTACHMENT INTEGRATED ANTENNAS STRUT TO BE ATTACHED TO CENTRE HOLE ONLY STRUT TO BE ATTACHED TO CENTRE HOLE ONLY STRUT PIPE ATTACHMENT STANDARD ANTENNAS is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
6 10a ATTACH AZIMUTH ADJUSTER ASSEMBLY. OPTION 1 - FOR ATTACHMENT TO NON-CIRCULAR STRUCTURAL MEMBERS. page 6 of 9 LEAVE LOOSE UNTIL ADJUSTMENT IS COMPLETE THEN ENSURE BRACKETS AND NUTS ARE BOLTED RIGIDLY TOGETHER AS SHOWN. APPLY CONDUCTIVE GREASE TO THREADS OF AZIMUTH ADJUSTER. ENSURE CORRECT BRACKET IS USED Ø18 HOLE FOR M16 TORQUE TO 95Nm M16 bolt must be attached to a structural member capable of supporting 5200N in accordance with TIA-222. The maximum allowable relative deflection between the antenna mounting pipe and the strut attachment point must be less than 2mm at the survival wind speed of the antenna. HOLE DIAMETER 18mm 0.5mm STRUCTURAL MEMBER is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or STRUCTURAL MEMBER
7 page 7 of 9 10b ATTACH AZIMUTH ADJUSTER ASSEMBLY. OPTION 2 - FOR ATTACHMENT TO CIRCULAR STRUCTURAL MEMBERS. LEAVE LOOSE UNTIL ADJUSTMENT IS COMPLETE THEN BRACKETS STRUCTURAL MEMBER (CIRCULAR) ENSURE CORRECT BRACKET IS USED Ø13.5 HOLE FOR M12 ENSURE BRACKETS AND NUTS ARE BOLTED RIGIDLY TOGETHER AS SHOWN WITH NO VISIBLE THREADS (VIEWED FROM UNDERSIDE FOR CLAIRTY) Clamps must be attached to a circular structural member (Dia 48mm-115mm) capable of supporting 5200N in accordance with TIA-222. The maximum allowable relative deflection between the antenna mounting pipe and the strut attachment point must be less than 2mm at the survival wind speed of the antenna. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to products or
8 ValuLine / Advantage Antenna Bulletin AZIMUTH & ELEVATION ADJUSTMENT page 8 of 9 ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE ADJUSTING AZIMUTH (ONCE ADJUSTMENT IS COMPLETE RE-TORQUE TO 95Nm) ENSURE THIS BOLT HAS BEEN LOOSENED BEFORE EL. ADJUSTMENT RE- ELEVATION ADJUSTMENT ±15 ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE ADJUSTING ELEVATION (ONCE ADJUSTMENT IS COMPLETE RE-) ENSURE SAFETY BRACKET IS SECURELY FITTED AT ALL TIMES ENSURE THIS NUT HAS BEEN LOOSENED BEFORE AZ. ADJUSTMENT RE- ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE ADJUSTING AZIMUTH (ONCE ADJUSTMENT IS COMPLETE RE-TORQUE TO 95Nm) AZIMUTH ADJUSTMENT ±12 ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE AZ. ADJUSTMENT RE- is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
9 ValuLine / Advantage Antenna Bulletin STRUT PIPE POSITIONAL RANGE page 9 of 9 LIMITS OF STRUT POSITION FOR ATTACHMENT TO APPROVED STRUCTURAL SUPPORT 5 5 DEPENDING ON RADIO INTEGRATION, STRUT ENVELOPE MAY BE RESTRICTED is a trademark of CommScope. All trademarks identified by or are registered trademarks or tradeany specifications or warranties relating to products or
Installation Instructions
Description The following pages show the steps required to assemble and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
More informationInstallation Instructions
put barcode here page 1 of 13 Description The following pages show the steps required to assemble and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides
More informationInstallation Instructions ValuLine 4ft Antennas
Rev: J Installation Instructions ValuLine 4ft Antennas 4ft (1.2m) Bulletin Version 08 page 2 of 27 Status RE Rev J Model Version 01 StatusRE Rev B This document is for the following: VHLP(X)4-*** 1.2m
More informationInstallation Instructions
page 1 of 7 Description These feeds are designed for installation in shielded standard types of parabolic antennas. The feed is designed for positive metal-to-metal contact between the feed and the reflector,
More informationInstallation Instructions
Description Instructions given in this bulletin apply to either a standard, unshielded or high-performance, shielded antenna. The antenna consists of a two-piece reflector, braced by a back structure;
More informationRevision B. Mar 2017 Side-By-Side Mounting Kit
-1 Revision B. Mar 2017 Side-By-Side Mounting Kit BSAMNT-SBS-2-2 GENERAL INFORMATION The BSAMNT-SBS-2-2 Mounting Kit allows mounting either two 350mm wide or two 457mm wide antennas with 2 mount points
More informationIMPORTANT! BEFORE UNPACKING AND ASSEMBLING THE ANTENNA MANUAL FULLY INSTRUCTIONS READ THIS INSTALLATION Rev: H
Rev: H IMPORTANT! INSTALLATION READ THIS MANUAL FULLY BEFORE UNPACKING AND ASSEMBLING THE ANTENNA Videos provide supplementary information- the instructions contained witin this bulletin must always be
More information457 mm (18.0") WIDE ANTENNAS
Revision D, January 201 Side-By-Side Mounting Kit BSAMNT-SBS-2- GENERAL INFORMATION The BSAMNT-SBS-2- Mounting Kit allows mounting either two 0mm wide or two 7mm wide antennas with mount points side by
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 8 ft Antennas PA, PAL, PAD, PAX, PADX DA, UA, DAX, UDA, UXA HTT 81.221-15 (e) These installation instructions have been written for qualified, skilled personnel. The antenna shall
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 8 ft Antennas PA, PAL, PAD, PAX, PADX DA, UA, DAX, UDA, UXA HTT 81.221-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 10 ft Antennas PA, PAL, PAD, PAX, PADX DA, UA, DAX, UDA, UXA HTT 81.222-11(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall
More informationInstallation Instructions 6 ft Antennas Adv. Backring (with T-Mount) PA, PAL, PAD, SP, PAX, PADX, SPX DA, UA, SU, SD, SDF, DAX, UDA, UXA, SDX, SUX
Installation Instructions 6 ft Antennas Adv. Backring (with T-Mount) PA, PAL, PAD, SP, PAX, PADX, SPX DA, UA, SU, SD, SDF, DAX, UDA, UXA, SDX, SUX NMT 628-00(e) DA, UA, SU, SD, SDF DAX, UDA, UXA, SDX,
More informationInstallation Guide for HP3 & HP4 ANTENNAS
Installation Guide for HP3 & HP4 ANTENNAS with Cast Mount 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 email; sales@radiowaves.com www.radiowaves.com IMPORTANT!
More information100A Series Low Power FM Antenna
Installation Instructions 100A Series Low Power FM Antenna Types 100A-1M, 100A-2F, 100A-2F-HW 20100326001_AEN Revision 03 Notice The installation, maintenance, or removal of antenna systems requires qualified,
More information2007 Shelby GT500 Long Tube Headers Installation
2007 Shelby GT500 Long Tube Headers Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationRevision C, June 2016 Pipe Kit for Mounting 1 to 3 Antennas 800PIPEKIT-X GENERAL INFORMATION
Revision C, June 2016 Pipe Kit for Mounting 1 to 3 Antennas 800PIPEKIT-X GENERAL INFORMATION The 800PIPEKIT-X is used for mounting one to three Commscope base station antennas to an existing pole measuring
More informationLong Tube Header Installation For Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C
Long Tube Header Installation For 2005-2008 Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C Precision manufactured using high quality austenitic stainless
More informationInstallation for Chevrolet Malibu 2.0L Turbo PN-11936
Installation for Chevrolet Malibu 2.0L Turbo PN-11936 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts
More informationExhaust System Installation for Audi S5, S4, and S6 PNs , ,
Exhaust System Installation for Audi S5, S4, and S6 PNs-140391, 140403, 140704 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts
More informationTONNEAU COVER INSTALLATION INSTRUCTION. Toyota Hilux 407L
TONNEAU COVER INSTALLATION INSTRUCTION Toyota Hilux 407L Piece Tonneau Cover Place these instructions in vehicle s glove box after installation is complete Care Instructions: Clean Tonneau Cover with a
More informationInstallation for Jeep Grand Cherokee SRT8 PN s , and 60634, 60635
Installation for Jeep Grand Cherokee SRT8 PN s-140632, 140633 and 60634, 60635 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure
More informationExhaust System Installation for Corvette, C6 or Z06 PN s , 11811, 11812, 11814, 11815, 11816, 11917
Exhaust System Installation for Corvette, C6 or Z06 PN s - 11810, 11811, 11812, 11814, 11815, 11816, 11917 ***** Please compare the parts in the box with the bill of materials provided ***** to assure
More informationExhaust System Installation for Audi S4, S5 & S5 Sportback PNs ,
Exhaust System Installation for Audi S4, S5 & S5 Sportback PNs 140740, 140749 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary
More information3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS
3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS TC00d / Vehicle Description: NISSAN NAVARA D0 DUAL CAB 3-PIECE TONNEAU COVER PARTS LIST NO. PART NAME QTY. NO. PART NAME QTY. NO. PART NAME QTY.
More informationInstallation for Dodge Challenger & Charger HellCat PN s , , , , , , ,
Installation for PN s-140642, 140646, 140647, 140648, 140666, 140667, 140668, 140669 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the
More informationPlease compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for this installation.
Installation for Chevrolet Corvette C7 Stingray & ZO6 (Standard exhaust) PN s - 11862, 11863, 11868, 11869, 11877, 11878, 11880, 11881 (Optional NPP) PN s - 11874, 11855, 11875, 11856 ZO6 PN s - 11902,
More information3PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger/Mazda BT-50 (without bedliner)
3PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger/Mazda BT-50 (without bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More informationHeader Installation For Jeep Wrangler
Header Installation For 2007-2008 Jeep Wrangler Precision manufactured using high quality austenitic stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationExhaust System Installation for the Ford Mustang PN s ,140584,140585,140589,140590,140591
Exhaust System Installation for the Ford Mustang PN s-140583,140584,140585,140589,140590,140591 Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years
More informationChevrolet Camaro (Gen6) Installation Guide PN 11920, 11921, 11924, 11925, 11926, 11927, 11930, 11931
Installation Guide PN 11920, 11921, 11924, 11925, 11926, 11927, 11930, 11931 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages) to assure that
More informationExhaust System Installation for Chevrolet Corvette C6 PN and
Exhaust System Installation for Chevrolet Corvette C6 PN-140128 and 140131 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationExhaust System Installation for the Ford Mustang PN s , , , , , , , ,
Exhaust System Installation for the Ford Mustang PN s-140583, 140584,1 40585, 140586, 140587, 140588, 140589, 140590, 140591 Precision manufactured using aircraft quality T-304 stainless steel; this system
More informationInstallation for the Ford Mustang V-6 PN s , ,
Installation for the Ford Mustang V-6 PN s-140586, 140587, 140588 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document
More informationExhaust System Installation for Chevrolet Corvette C7 Stingray PN 11855, 11856
Exhaust System Installation for Chevrolet Corvette C7 Stingray PN 11855, 11856 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read
More informationPlease take time to read and understand the following
Thank you for purchasing a Borla Performance Down Pipe. This Down Pipe has been designed for use only with a Borla Performance Cat-Back exhaust system. Replacement down-pipes are designed exclusively for
More informationInstallation Instructions for Challenger R/T: , , , Charger R/T: , , ,
Installation Instructions for Challenger R/T: 140713, 140714, 140715, 140716 Charger R/T: 140722, 140723, 140724, 140725 ***** Please compare the parts in the box with the bill of materials provided *****
More informationExhaust System Installation For Dodge Challenger 3.5L
Exhaust System Installation For Dodge Challenger 3.5L BORLA PERFORMANCE INDUSTRIES These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please
More informationExhaust System Installation for Nissan GT-R PN 12658
Exhaust System Installation for Nissan GT-R PN 12658 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationInstallation for Dodge Challenger R/T PN s ,
Installation for PN s-140707, 140708 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages) to assure that you have all the parts necessary for this
More informationInstallation, Operation and Maintenance
Installation, Operation and Maintenance Type ES93( ) 9.3-Meter ESA Bulletin OM93 Revision D 9.3-Meter Earth Station Antenna Andrew Corporation 10500 West 153rd Street Orland Park, IL U.S.A. 60462 Telephone:
More informationExhaust System Installation for the Ford F-150 PNs , , , , , ,
Exhaust System Installation for the Ford F-150 PNs 140693, 140694, 140695, 140696 140697, 140698, 140699, 140700 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
More informationBy installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms stated below.
Thank you for purchasing a Borla Performance Cat-back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationLong Tube Header Installation For Ford Mustang GT
Long Tube Header Installation For 2005-2008 Ford Mustang GT Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla
More informationBanks Ram-Air Intake System
Banks Ram-Air Intake System 1997-2006 Jeep 4.0L THIS MANUAL IS FOR USE WITH KITS 41816 General Installation Practices 1. For ease of installation of your Banks Ram-air intake system, familiarize yourself
More information2005 ODU Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly Antenna Boom Arm Assembly Antenna TRIA Attachment Mounting the Antenna Base-Assembly Installing the Antenna Elliptical
More informationInstallation Guide for Chevrolet Camaro ZL1 PNs ,
Installation Guide for Chevrolet Camaro ZL1 PNs -140726, 140727 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages) to assure that you have all
More informationFollowing symbols can be found next to text outlining important information.
Revision J, October 2016 641 mm Profile Panel Antennas General This instruction manual contains all necessary information required to assist in the correct installation of Panel Antennas of 641 mm (25.2
More informationInstallation for Honda Civic Type R PN
Installation for PN-140738 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationPRO STREET-S INSTALLATION INSTRUCTIONS
PARTS & HARDWARE LIST Part Number Description Qty Part Number Description Qty A 1534.8100 DAMPER ASSY FRONT 2 B 1534.8200 DAMPER ASSY REAR 2 C PDK4.TOOL 4mm ADJUSTMENT TOOL 1 D PDK6.TOOL 6mm ADJUSTMENT
More informationInstallation for Chevrolet Corvette C7 Stingray & ZO6 PN **
Installation for Chevrolet Corvette C7 Stingray & ZO6 PN - 12669** These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2000 1984 1991 Toyota 2 Wheel Drive Pick-Ups 2 Front Dropped Spindles Congratulations!
More informationAKRAPOVIC CARBON-FIBER PARTS for the SUZUKI B-KING (2008)
Installation instructions: *502102* AKRAPOVIC CARBON-FIBER PARTS for the SUZUKI B-KING (2008) Congratulations on purchasing an Akrapovic carbon-fiber part. Please read these installation instructions carefully.
More informationCOOPER POWER SERIES. 200 A loadbreak junction 15 and 25 kv class installation instructions. Loadbreak Connectors MN650015EN
Loadbreak Connectors MN650015EN Effective December 2015 Supersedes S500-15-1 October 2013 COOPER POWER SERIES 200 A loadbreak junction 15 and 25 kv class installation instructions DISCLAIMER OF WARRANTIES
More informationInstallation, Operation and Maintenance
Installation, Operation and Maintenance Type ES45P, MP, MPJ 4.5-Meter ESA Bulletin OM45P Revision F 4.5-Meter Earth Station Antenna Andrew Corporation 10500 West 153rd Street Orland Park, IL U.S.A. 60462
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationINSTALLATION AND OWNER S MANUAL Wing Deflectors, Fairing Mount N5107 and N5109 for HONDA GL1800
INSTALLATION AND OWNER S MANUAL Wing Deflectors, Fairing Mount N5107 and N5109 for HONDA GL1800 Thank you for purchasing a National Cycle product. Please read these instructions carefully and thoroughly
More informationBanks Ram-Air Intake System
Banks Ram-Air Intake System 1997-2006 Jeep 4.0L THIS MANUAL IS FOR USE WITH KITS 41816 Gale Banks Engineering 546 Duggan Avenue Azusa, CA 91702 (626) 969-9600 Fax (626) 334-1743 Product Information & Sales:
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationM H F150 4X4 Rear Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
More informationThank you for purchasing a Borla Performance Rear Section Exhaust System.
Thank you for purchasing a Borla Performance Rear Section Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationInstallation Instructions
Installation Instructions Bulletin 237471 MACXLine 8-3/16" Rigid Coaxial Transmission Line Including Inners Only Replacement Systems Revision E Contents Description 1 Components 1 Installation Tool Kit
More informationInstruction Manual For The WildBlue 65cm x 75cm Elliptical Ka Antenna
Raven 2009ODU Manual Instruction Manual For The WildBlue 65cm x 75cm Elliptical Ka Antenna 1035-09-004-A Caution This instruction leaflet will assist you in the correct installation of the product. Read
More informationBMS MI30 FRONT. Shock Absorber Kit for BMW M3 (E46) Mounting Instructions
Kit Contents Description Part No Pcs Shock absorber Dust Boot 1016-01 Lock nut M14 467-04 Lower spring seat 465-0 Lock ring 466-0 Washer 4619-06 Rebound adjuster 461-0 Used for both front and rear C-spanner
More informationCougar B Series Electric Vibrators 3 Frame
Cougar B Series Electric Vibrators 3 Frame Go to Cougar B Series Electric Vibrators web page Operator s Manual M3929 Important MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO CONTAMINATION
More informationInstallation for Ford Explorer PN s , ,
Installation for Ford Explorer PN s- 140656, 140659, 140658 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document completely
More informationInstallation for Honda Accord PN s 11840, 11853, 11949
Installation for Honda Accord PN s 11840, 11853, 11949 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts
More informationInstallation for Ford F-150 Raptor (V6 Ecoboost) PN s , 60638, 60650*
Installation for (V6 Ecoboost) PN s- 60637, 60638, 60650* ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationTools, Equipment and Supplies Needed:
153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.
More informationExhaust System Installation PN , , , , &
Exhaust System Installation PN-140415, 140416, 140417, 140438, & 140466 BORLA PERFORMANCE INDUSTRIES These instructions have been written to help you with the installation of your Borla Performance Exhaust
More informationINSTALLATION INSTRUCTION PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTION PART NUMBER: 24-6003 1994-2001 ACURA Integra L4-1.8L Manual Trans. C.A.R.B. E.O. # D-670 Non VTEC models ONLY AEM bypass valves
More informationFord Mustang GT Long Tube Header Installation
2005-2006 Ford Mustang GT Long Tube Header Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationExhaust System Installation for Chevrolet Silverado and GMC Sierra PN , , , , ,
Exhaust System Installation for Chevrolet Silverado and GMC Sierra PN-140535, 140536, 140537, 140538, 140539, 140540 ***** Please compare the parts in the box with the bill of materials provided *****
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationVOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationThank you for purchasing a Borla Performance Stainless Steel Header.
Thank you for purchasing a Borla Performance Stainless Steel Header. Precision manufactured using aircraft quality T-304 stainless steel; these headers are designed to endure years of heavy use. Installing
More informationAiro Pro 1.5 Gallon Sprayer Airo Pro 1 Gallon Sprayer Airo Pro.5 Gallon Sprayer Airo Pro Sprayer Manual
Airo Pro 1.5 Gallon Sprayer 501-502-180 Airo Pro 1 Gallon Sprayer 501-504-210 Airo Pro.5 Gallon Sprayer 501-505-180 Airo Pro Sprayer Manual Safety Notices Safety Instruction Keep out reach of children
More informationSYDEX / MAINTENANCE AND OPERATION MANUAL
Installation Operation and Maintenance Attention: The following explanations have the aid to give you all possible information over the SYDEX pumps range. The right choosing of the pump is depending from
More informationPART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More information2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: (99-137)
2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: 422046 (99-137) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions
More informationInstructions for Porsche PN s * and
Instructions for Porsche 997.2 PN s-140711* and 140712 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationInstallation for Chevrolet Silverado/GMC Sierra PN s ,
Installation for Chevrolet Silverado/GMC Sierra PN s-140550, 140551 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger (with bedliner)
PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger (with bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationSUS MI10 front front. Shock Absorber Kit for Subaru Impreza (GRB)
Before installing this product, check the contents of the kit. If anything is missing, please contact an Öhlins dealer. Kit Contents Shock absorber Upper spring seat Dust boot Top mount Bearing spacer
More informationInstallation for Chevrolet Silverado & GMC Sierra PN s , , ,
Installation for Chevrolet Silverado & GMC Sierra PN s-140717, 140718, 140719, 140720 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to
More informationGearbox Installation Manual
Gearbox Installation Manual Rotork Gears IW, MOW, MTW, IB and IS ranges (Electronic copy available on www.rotork.com)! This manual contains important safety information. Please ensure it is thoroughly
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationOWNERS MANUAL. Model No LB. PUSH BROADCAST SPREADER. Assembly Operation Maintenance Repair Parts
OWNERS MANUAL Model No. 45-02102-101 SHIELD UP - 8 TO 18 FT. SPREAD WIDTH SHIELD DOWN - 3 TO 4 FT. SPREAD WIDTH 125 LB. PUSH BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully
More informationCable Carriers. Information about further items of our product range is available on request:
Cable Carriers Information about further items of our product range is available on request: Copper head rails Current collectors Insulators Plastic- and neoprene-cables Junction boxes Cable reels Radio
More informationChevrolet Camaro (Gen6) Installation Guide Long Tube Header PN 17293*
BORLA PERFORMANCE INDUSTRIES Chevrolet Camaro (Gen6) Installation Guide Long Tube Header PN 17293* ***** Please compare the parts in the box with the bill of materials provided ***** (view the following
More information2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation Instructions
2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation Instructions P/N: 422046 and 422119 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation
More information2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014
2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &
More information1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
More information