PLF - Plasma Floor Lift

Transcription

1 SHEET 1 of 6 DESIGN HIGHLIGHTS Quiet smooth action with variable speed motion Full cable management Stylish look and finish Wide range of mounting options OPTIONS Marine suitable option FUNCTION n electric lift to reveal a television from a floor. separate electric walk on flap is included. SUITBILITY This product can be custom made to suit any screen from 32" to 85". Maximum Load is 12Kg [265lb] Swivelling version with 18 degree swivel to the left and right. Swivelling version has three learnable preset positions. B and O and Loewe Mount Options. Telescopic versions for restricted floor depths. SPECIFYING fully waterproof floor recess is required to install the mechanism. Various floor finishes can be accommodated. CONTROL Supplied with basic infrared remote. Can be learnt by many learning remotes. lso has switch control and RS232 so can be operated by relays, switches, Crestron / MX or Lutron systems. WRNING It is the responsibility of the installer to warn all potential end users of the dangers of interfering with mechanisms during operation IMPORTNT Mechanisms which lift or move weights need to be checked on a yearly basis for any damage which may result in an accident

2 SHEET 2 of 6 PLN The mechanism is supplied as two parts. n electric flap mechanism and the main lift mechanism. Use the chosen screen size to determine the mechanisms required. For example: Screen of 165mm[65."] width and 96mm[37.8"] height would fit in a lift with reference PLF H191 W182. SCREEN WIDTH F F custom height pole can be used by changing the overall lift height. The swivelling version (PLFS) has the same dimensions. Other widths and heights available. UP Maximum Screen Thickness - 16mm [6.3"] Mechanism Height Maximum Screen Height Floor Recess Height Pole Height H21 16[41.7] 21[79.1] 5[19.7] H191 96[37.8] 191[75.2] 5[19.7] H181 86[33.8] 181[71.3] 5[19.7] SCREEN BSE/FLP WIDTH POLE Stainless Steel Pole for swivel and non swivel versions. MechanismWidth Maximum Screen Width Floor Recess Width Base/Flap Width W [53.1] 152[59.8] 137[53.9] W [57.1] 162[63.8] 147[57.9] W [61.] 172[67.7] 157[61.8] W [65.] 182[71.7] 167[65.7] Base DOWN Removable floor insert to get access to mechanism. FLOOR RECESS Control System Electric flap mechanism retracts flap into the floor before lifting the screen. Flap can be walked on. Power Supply SECTION F-F Lift mechanism. The lift and the electric flap mechanism mount to the front face of the floor recess. Base fills the opening in the floor when in the up position. FLOOR RECESS WIDTH

3 SHEET 3 of 6 B PLN B INSERT RECESS WIDTH= FLOOR RECESS WIDTH+15mm[5.9"] Flap to fill the opening when the lift is down to Recess for Floor Insert Floor Insert Floor Insert Base to fill opening when in the up position. 2 - Mechanism is fixed to this front face at the top and bottom. 3 - Electric flap mechanism is fixed to this front face here on both sides. 4 - Power Supply Unit needs 11/24V C Supply 5 - Control Unit needs 11/24V C Supply 6 - Flap Unit needs 11/24V C Supply 7 - Cable Entry points FLOOR RECESS 5 7 SECTION B-B SCLE 1 : 12 BSE WIDTH SECTION - SCLE 1 : Clearance as base moves Viewing Side Clearance as base moves FLOOR RECESS WIDTH

4 SHEET 4 of FLOOR INSERT Viewing Side The Floor Insert drops into a recess created in the finished floor surface OPENING WIDTH to 36 FLP OPENING WIDTH = BSE/FLP WIDTH + 6mm [.25] The Base and the Flap will fill the opening in the floor insert with a gap of 3mm [1/8"] around the edge. BSE/FLP WIDTH The Floor Insert, Base and Flap all need to be made from the finished floor material. This can be timber, stone or carpet (over timber). The maximum weight of the Base or Flap must be no more than 25Kg [55lb]. BSE 3 to 36 Stone or tiles can be used. To simplify the installation attach to an 18mm [.75] piece of plywood. Up to 18mm of stone attached to 18mm of plywood will give the maximum thickness of 36mm [1.5] BSE/FLP WIDTH Viewing Side 3 to 36

5 Fitting Notes SHEET 5 of 6 GENERL FITTING NOTES 3mm to 36mm recess for insert.5 12 Possible control box location PLN Fix the lift here The lift can be checked and operated prior to insertion in the floor. Lay the main lift on its back and place the flap mechanism alongside. Connect the control system and test. Prior to insertion in the hole, grease the main rack. Fit the lift in the centre of the hole. If the hole is too deep then place blocks underneath to keep the top of the lift at 12mm [.5] from the top Position the flap mounting plates here on each side. Use bolt heads no greater than 7mm tall. Use sufficient fittings so that the weight of the mechanism is supported along with the possible weight of people walking on top. djust dimensions if the hole is wider than the specified width. The flap can then be dropped into place using the key hole slots engaging on the flap mounting plates. Fix on the flap mounting plates at the position shown. Change dimensions if the hole is wider than the width shown. Fix the lift here Power Supply Unit needs 11/24V C Supply SECTION - SCLE 1 : 1

6 Fitting Notes SHEET 6 of 6 GENERL FITTING NOTES UP SWITCH DJUST This stop controls when the lift stops at the top. djust with Caution! Fix Flap to the Flap Mechanism with screws from underneath. Use the Insert to assist when positioning Make sure the motor is stopping. Observe lights in control box so there is confidence that the motor has stopped. With the beam at the top the Base can be fitted. Use the Insert to assist when positioning Remove uprights and fix to the screen. Then hook screen in place. Do not mount to high - clearance is needed as the flap l lifts and closes. FLP DJUST Slots enable Left to Right movement. Bolt enables Up and Down adjust. Run cables through cable track and then up through the pole. End plate enables Rock and Front to Back adjust. WRNING lways cover the STOP button on the remote when moving the mechanisms after fitting new parts.