Version vom 18.April 2011 noch ned freigegeben! Korrekturlesung Auto-control system for private pools. POOLKLAR Touch XL

Transcription

1 WERNER Dosiertechnik Version vom 18.April 2011 noch ned freigegeben! Korrekturlesung Auto-control system for private pools Mess-, Regel- und Dosiertechnik für ph-regulierung und Desinfektionsmittel Technische Änderungen vorbehalten Hettlinger Straße 17 Tel. +49 (0) 8272/ D Wertingen- Geratshofen Fax +49 (0) 8272/

2 Inhaltsverzeichnis 1 Notes to this manual scope of application Target group Keeping of the manual Further information Used symbols Safety aspects Intended use Delivery scope Description Delivery scope Transport damage Identification of the device Device description Installation Place of installation Tapping points for measuring water Installation proposal Commissioning Setting of the Control parameters see for this page 22 Commissioning form ph-electrode Cleaning glass beads Measuring water flow Dosing pump heads Chemicals Switch off at backwash and vacuuming Electrical connections To open and close the housing Wiring plan The power board NT_PKT_2 fuses, relay The I/O- Board IO_PKT_ The amplifier MV_PKT_ OPTIONS OPTION Temperature OPTION Filter pressure Operation of the Touch display Operation Indication and Programmes Normal operation QuickInfo Dosing delay Start routine Alarm Main menu Main menu Settings Original Bedienungsanleitung in deutsch - Version (V _01_09) 2/24

3 Main menu Settings ph Main menu Settings mv (Disinfection) Main menu Settings dosing capacity Main menu Settings temperature Main menu Settings pressure Main menu Settings Dosing delay Main menu Settings system Main menu Settings system pass word Main menu Settings system network Main menu calibration Main menu calibration ph- electrode Main menu calibration redox- electrode Main menu Service Main menu Service output test Main menu Service input test Main menu Service Info Main menu Service event log list Maintenance Filter ph-electrode Injection valves Dosing heads Redox-electrode Diagnosis and troubleshooting check of dosing function Check of the electrodes taking out of service hibernation - storage Technical data Commissioning form Spare parts list Own notes Original Bedienungsanleitung in deutsch - Version (V _01_09) 3/24

4 1 Notes to this manual 1.1 scope of application This manual describes the installation, commissioning and operation of the unit. This manual is guilty for the from version -> see foot print. 1.2 Target group Only instructed persons shall operate this unit. Works on electric or water side should only be executed by skilled persons. 1.3 Keeping of the manual All manuals must be kept near to the unit and must be accessible anytime to any operating persons. 1.4 Further information Further information as selection needs for the operation parameters you get from your dealer. 1.5 Used symbols In this document the following symbols are used: DANGER! Danger indicates a safety advice, that may lead to death or severe injury if ignored. WARNING! WARNING indicates a safety advice, that may lead to death or severe injury if ignored. ATTENTION! ATTENTION indicates a safety advice, that may lead to injury if ignored: ATTENTION! ATTENTION indicates a safety advice, that may lead to material damage if ignored Note A note indicates information that may lead to operation problems if ignored Tipp A Tipp indicates information that may lead to improvements in the operation 2 Safety aspects 2.1 Intended use The device is intended for auto-control of the water quality of private swimming pools. Please pay attention at the handling of the chemicals! WARNING! Danger of chemical burn and poisoning - Never mix chemicals - Use only chemicals that are allowed for your swimming pool water and care - For maintenance use protective clothes. Original Bedienungsanleitung in deutsch - Version (V _01_09) 4/24

5 3 Delivery scope Description 3.1 Delivery scope The is delivered with following accessories: - buffer solution ph7, ph4, Redox-solution 468 mv - electrode cleaner solution, distilled water ½ l - glass beads for cleaning the platinum electrode, electrolyte, spare seals - 2 x ball valve ½ with immersion tube - each 7m tube 6x1mm PE (for measuring water) and PTFE (for dosing tube) 3.2 Transport damage Please check the device and accessories direct after getting it on completeness and intactness. 3.3 Identification of the device For spare parts needs or technical advice it is necessary to know the type indication and the series no. You can find the type label right side at the controller housing. The programmed version you can find by selecting the menu Service Info. 3.4 Device description controller 2. buffer solutions 3. prove cylinder to check the redox-tension 4. measuring water /dosing discharge to pool 5. measuring water supply 6. filter 7. probe water discharge 8. measuring water flow control 9. flow control valve 10. redox- electrode 11. measuring cell 12. ph- electrode 13. peristaltic dosing pumps 14. injection valves 15. suction lances (not on picture) The is delivered pre-mounted as seen on the picture for ease to mount at site. Only the ph-electrode (12) has to be put into the measuring cell and the dosing heads of the dosing pumps must be pushed onto the shafts of the dosing motors. By tipping on the Touch display on a symbol or a value you can get more information or you can change the parameters. This is supported by real text. The chemical leading items as pump, injection valve and suction lance are indicated by color marks to avoid interchange. Acid containing parts are indicated red and are situated left side, chlorine containing parts are indicated yellow and situated right side. Attention! if you interchange the chemicals you will get wrong water quality results. In addition a dangerous situation can result. red = ph-value/acid - yellow = disinfection/chlorine Original Bedienungsanleitung in deutsch - Version (V _01_09) 5/24

6 4 Installation 4.1 Place of installation For ease operation and maintenance please look for a good accessible mounting place, not at risk of frost or direct sun shine. 4.2 Tapping points for measuring water Only with good hydraulics a reasonable effect of the auto-control of the ph and the redox can be achieved. The dosed chemicals should reach all places in the pools within a short time (< 5 minutes). Also with bathers load the chlorine concentrations should be similar at different places of the pool. The measuring water in the cell should be identical to that in the pool. So it should be conveyed as fast as possible to the cell. If you have an overflow system with balance tank and fresh water supply herein, this must be considered. If highest quality is required, a extra pump for the measuring water is to be mounted. It is recommended to link the power supply of the POOLKLAR to the power supply of the filter pump. 4.3 Installation proposal Normally the water take off is between pump and filter, the injection behind the heat exchanger. For the connection to the piping please use the by-packed valves with emerging tubes, that are to be shortened so that their end is reaching to the middle of the pipe. ACHTUNG! As the water behind the POOLKLAR is very corrosive, the injection point should be behind the heat exchanger. At an overflow system it is recommended to install an extra measuring water pump Original Bedienungsanleitung in deutsch - Version (V _01_09) 6/24

7 5 Commissioning Before taking into service the following points have to be worked through. Please see for this too point 3.4 page Setting of the Control parameters see for this page 22 Commissioning form The POOLKLAR is at works set with certain parameters that are to be adjusted to the needs of your pool. Normally you can use these parameters for start and change them after some days when you see the reaction on your pool water quality. The most important will be the look on your values for free chlorine. 5.2 ph-electrode Take the ph-electrode from the packing and pull off the protection cap. Screw off the connector head and screw the electrode into the cell. Now screw on the connector head again on the electrode. After an hour time it is to check whether a calibration is needed. For this take out the electrode again from the cell and place it in the buffer solution ph 7,0. A calibration is needed if the indicated value has a difference to 7,0 more than 0, Cleaning glass beads The blue glass beads are to clean the surface of the platinum electrode to get stable values for the redox tension. Pull off the cable from the redox electrode (10) and screw out the PVC electrode holder from the cell. Now put the glass beads onto the platinum surface to cover the surface. Screw in again the electrode into the cell and push in the cable to the electrode. At screwing in the Redox-Electrode pay attention that no glass beads are in the thread. ATTENTION! Check all tube connections to be dense. Plastic connection are only fastened by hand! 5.4 Measuring water flow At the flow control valve (9) the water flow is to be adjusted. The switch bobbin must be pushed to top. Only in this position dosing is possible. The glass beads must rotate on the electrode surface; they should not be lifted by too high flow of the water. 5.5 Dosing pump heads Push the dosing heads on the motor shaft till the lockers do klick. 5.6 Chemicals Place the two chemical containers under the POOLKLAR. It is strongly recommended to place them into safety tubes to prevent leakage on the floor: Left, acid right chlorine. Place the suction lances into the containers. red = acid - yellow = chlorine For the right function of the POOLKLAR it is important to know what disinfection chemical was used before. If it was other chlorine or non chlorine type there are reactions in the water that may affect the disinfection capacity of the chlorine now in use. Chlorine compounds on organic basis (Dichlor, Quickchlor and others) do reduce the redox tension at same measured chlorine levels at use for longer time; the disinfection power of the chlorine is reduced. Original Bedienungsanleitung in deutsch - Version (V _01_09) 7/24

8 That means that at a certain level of the redox tension you get higher chlorine concentration. If you don t want the higher chlorine level, you have to select a lower set value for the redox tension, but that means lower disinfection power. Best would be in this case to empty your pool and to fill fresh water. 5.7 Switch off at backwash and vacuuming During backwash the circulation back to the pool is interrupted but the water supply to the POOLKLAR is not. Dosing could run on to the standing water in the return pipe. It would be possible that after finishing the backwash high concentration of chlorine could be flushed to the pool. To avoid this it is recommended to switch off the POOLKLAR during backwash. If the vacuuming of the pool floor is executed through the filter we get high pollution rates to the POOLKLAR that will block the filter on the system. So we recommend switching off of the POOLKLAR in this time too. 6 Electrical connections 6.1 To open and close the housing No tools are needed. To open the housing cover you lift a little the lower and upper sideward clips and you can then lift the cover forward, the upper cover clips are running in their grooves to their front stop. Now the cover can be flipped up and supported by means of the strap. Press To close the housing the strap must be loosened to backside and the cover is then to be closed downwards. Now loose the upper sideward clips and push the cover backwards. To seal the cover push at all 4 edges with slight. The cover closes with a slight klick. Klick To connect additional cables to the controller at the bottom of the housing you find some push out for cable connectors. Original Bedienungsanleitung in deutsch - Version (V _01_09) 8/24

9 6.2 Wiring plan DANGER! All jobs at the electrics may only executed by skilled persons under observance of the legal regulation! The power board NT_PKT_2 fuses, relay fuse Nominal current function F1 125 ma Minus 5 VDC F2 1,0 A Plus 24 VDC F3 315 ma Plus 5 VDC (pre fuse for F1) F4 max. 2 A Relay - K3 alarm F5 max. 2 A Relay - K2 - desinfection 2-point F6 max. 2 A Relay - K1 temperature F7 1,0 A Internal power supply (F1 to F3) F8 4,0 A Total power supply (F1 to F7) The figure shows as example the connection for a 230 Volt circulation pump for the pool heating Original Bedienungsanleitung in deutsch - Version (V _01_09) 9/24

10 6.2.2 The I/O- Board IO_PKT_ The amplifier MV_PKT_2 Original Bedienungsanleitung in deutsch - Version (V _01_09) 10/24

11 Fuses The fuses F4 to F6 are only to be fit, if the corresponding users 230 Volt are connected. For a non volt control the fuses are to be seperated. Fuse Current Fuse type Function F1 125 ma Micro- Sicherung Minus 5 VDC F2 1,0 A - ll - Plus 24 VDC F3 315 ma - ll - Plus 5 VDC (Pre-fuse for F1) F4 max. 2 A - ll - Relay- K3 - alarm F5 max. 2 A - ll - Relay - K2 - desinfektion 2-Punkt (Brom, Elektrolyse) F6 max. 2 A - ll - Relay - K1 - temperatur F7 1,0 A 5 x 20mm Mains internal supply (Pre-fuse for F1 bis F3) F8 4,0 A - ll - Mains total (Pre-fuse for F1 bis F7) Relay Outputs The relay outputs can be used non volt or with 230VAC. Non volt: upper 3-pole push connector (NC-C-NO) NC = normal closed open for function NO = normal open closed for function C = common contact 230V: lower (L1/N/PE) and upper (NC-C-NO) push connector The maximum current for each output is 2 Amp. If a higher load must be switched an additional power relay must be used. The total current of all outputs may not exceed 4 amperes. Original Bedienungsanleitung in deutsch - Version (V _01_09) 11/24

12 6.3 OPTIONS OPTION Temperature The implemented temperature control can be used for the heating of the pool water temperature. If the heating is executed by a heat exchanger it must be assured that the control of the heater pump is linked to the filter circulation pump that the heating pump may only run at running pool water circulation. Emerging sockets must be corrosion resistant! Further information please look at the operation manual OPTION Temperature OPTION Filter pressure With the measure of the filter pressure you can get information for the need of a filter backwash. Further information please look at the operation manual OPTION Filter pressure. Original Bedienungsanleitung in deutsch - Version (V _01_09) 12/24

13 7 Operation of the Touch display QuickInfo actual values actual dosing rate Value red alarm low or alarm high alarm off IN list start OUT list Status line menu date/time Change of the parameter, calibration or test functions are to the selected by touching the value or menu point easily. Description of the symbols IN - list red = container acid empty yellow = container chlorine empty leakage of a pump - dosing hose is broken Measuring water flow too low Pressure indication for backwash Dynamic time control active low dosing No distinction between the values value indication will be low! OUT - list red = output ph active, acid pump runs yellow = output disinfection active, chlorine pump runs Output temperature active heating pump runs Alarm relay active At right side Alarm relay is deactivated To interrupt the dosing delay To main menu Original Bedienungsanleitung in deutsch - Version (V _01_09) 13/24

14 7.1 Operation Indication and Programmes Normal operation The values are indicated and controlled No irritation QuickInfo With the function QuickInfo, the control parameter for ph-value, redox-tension und temperature can be seen directly. For this touch the wanted field No change of the parameters is possible Dosing delay At any switch on of the POOLKLAR dosing is suppressed for the set delay. This time has to be chosen so long that it is sure that actual pool water flows through the measuring cell. Software alarms are suppressed in this time With touching this time can be interrupted (e.g. at a maintenance job) and the POOLKLAR is running as set Start routine If one of the values is outside the control range (p-range) a dynamic dosing time monitoring is active: if a measure value does not reach the control range with a certain time dosing is stopped and alarm is given. This irritation is indicated by the symbol and can only be reset by a new start or a manual reset. Dieses Zeichen fehlt hier!? Alarm The symbol in the out -line indicated 1 or more alarms. The alarm relay is activated. We distinguish between alarms (software-alarm e.g. alarm high, alarm low) and irritations (switch inputs). At alarms the value is red colored. At irritations the according symbol is shown in the In -line. Alarms resp. irritations must be active at least for 5 seconds to be indicated. Original Bedienungsanleitung in deutsch - Version (V _01_09) 14/24

15 Some alarms are reset automatically as empty container or measuring water flow. The alarm Time monitoring must be reset manually! 7.2 Main menu automatic Back to normal control Settings to change control parameters and systems Settings calibration to calibrate the ph & redox- electrode service tests for input- and output-functions, Info and occurrence Main menu Settings ph control parameter ph Desinfektion control parameter disinfection Dosing rate Adjust dosing rate to pool size Temperature control parameter for pool heating Druck indication point for backwash Dosing delay System Date/ time, pass word, display brightness, reset Main menu Settings ph Alarm low lower alarm value, alarm relay is activated Set point this value is wanted to be reached Control range within this range we get proportional dosing, i.e. the greater the difference between the value and the set point, the longer dosing is executed with a dosing cycle. Maximum dosing at the end of the range = 50 seconds At the 2-point control this range is to define the hysteresis. Alarm high high alarm value, alarm relay is activated Time monitoring if the control range is not reached within 3x the set time, the dosing is stopped and alarm relay is activated. Important: this alarm must be reset manually! Original Bedienungsanleitung in deutsch - Version (V _01_09) 15/24

16 Main menu Settings mv (Disinfection) Identical to the Settings for ph. If you measure too high values for free chlorine: set lower values for redox or contrary Main menu Settings dosing capacity This is to adjust the dosing capacity to the chemical consumption needs of the pool. Especially for small pools this is important to avoid overdosing. If the values change up and down: lower the dosing capacity and/or increase the proportional range If you get the alarm indicating that the set value cannot be reached: increase the dosing capacity or lower the control range. Cycle time Dosing is organized in cycles to avoid coming together of the two chemicals whereby for both chemicals dosing times and pause times are defined. The shortest dosing cycle is 120 seconds, maximum dosing time is each 50 seconds with each10 seconds pause in between. That means that all 2 minutes dosing is activated in relation to the distance to the set point. An extension of the cycle time does extend the second pause time and so the dosing capacity is reduced. Example 1: 120 seconds example 2: 180 seconds ph mv ph mv sec. 120 sec. 0 sec. 180 sec Main menu Settings temperature Alarm low lower alarm value, alarm relay is activated Set point this value is wanted to be reached Control range = hysteresis if the temperature falls lower the hysteresis, the output for temperature (pump) is activated. Example: set point 25 C 2,0 K act. 23 C = output active Alarm high upper alarm value Offset fort he calibration of the temperature sensor If instead of the temperature ---- is indicated, you have following possibilities: 1. no temperature sensor is connected OPTION 2. the control range is on off, the control function is deactivated. 3. a sensor or cable break >1650Ω 170 C 4. a sensor or cable shortcut < 880Ω -30 C Original Bedienungsanleitung in deutsch - Version (V _01_09) 16/24

17 Main menu Settings pressure Measuring value: Shows the pressure indicated by the pressure sensor Backwash indication indication point for backwash. It should be adjusted so that a backwash indication is reached within 1 week. At reaching the indication point the symbol IN - line. is shown in the In case the filter is not backwashed in time or well the water quality (organic substances react with the chlorine) gets worse. To help the operator you can fix an indication point for backwash. If done, at reaching the set filter pressure you get the symbol information, the function is not affected. in the alarm indication line. This is only for Main menu Settings Dosing delay At any switch on of the filtration/poolklar the dosing is suppressed for the set delay. This time has to be chosen so long that it is sure that actual pool water flows through the measuring cell Main menu Settings system Date/time Setting of date and time Pass word Setting the pass word from works no pass word is set Display brightness To trim the display brightness to the environment Network To set the network addresses Reset To set back the parameters to works Settings Main menu Settings system pass word The main menu Settings can be locked against non authorized actions by setting a pass word. As pass word any number from can be taken. At works no pass word is set. important! Please store your pass word carefully. It can only be reset by the field service! Original Bedienungsanleitung in deutsch - Version (V _01_09) 17/24

18 Main menu Settings system network The POOLKLAR controller has implemented an interface with RJ45 connector. By means of this interface the front display can be transferred to external devices as PC-Monitor, Tablet-PC or Smartphone. TIPP! Further information you can get from our works service Main menu calibration ph to the calibration mode ph mv to the calibration mode Redox The calibration mode is conducted by real texts. By touching the AOKA the done steps are quit. Calibration values are taken if the value is stable for 15 seconds. At the end the reached electrode values are indicated and an evaluation of the electrode quality is done. At small deviations the calibration is taken over; at greater deviations a information cleaning or exchange is given Main menu calibration ph- electrode The ph-electrode gives as measuring signal a tension that is converted to ph indication. ph7 = zero point tension the zero point tension should be 0mV +/-30mV. ph4 = second check point to define the performance of the electrode. mv/ph = slope the slope at 25 C should be 59 mv/ph example: (mv at ph7 mv at ph4 = 3pH x 59mV = 177mV) Evaluation of the ph-electrode: Indication cleaning At a zero point tension > +/-41mV the indicated value is colored yellow and the mark for cleaning is indicated. Same indication at a slope < 52mV or > 63mV/pH. Indication irritation At a zero point tension > +/-61mV the indicated value is colored red and the calibration is not executed. Same with slope < 50mV or > 65mV/pH. The electrode is faulty and must be changed. If the calibration is not executed cause of faulty electrode, the control runs on with last values. Original Bedienungsanleitung in deutsch - Version (V _01_09) 18/24

19 Main menu calibration redox- electrode With the menu calibration redox- electrode the redoxelectrode is to be calibrated. The redox buffer solution of WDT brings a tension of 468mV at 25 C, see label. As the check tension is free to choose this calibration can be done with other buffer solutions too. Please pay attention to the dependency of the solution tension on the temperature Main menu Service Output test Test programme for pumps and relay outputs Input test Test programme for switch inputs Info To get the software version Event log In the event log list you find all irritations and alarms chronologic assorted max 100 events Main menu Service output test The output test is to check the function of the connected pumps and relay. The selected output is active for 100 seconds. Touching AEsc. the test function can be interrupted any time. Cause of safety reasons the dosing tests function only when the measuring water flows well, no interruption is indicated Main menu Service input test The input test is to check the function of the connected monitoring switches. The status of the switch is indicated by a 0 (open) or 1 (closed). All the switches (level and measuring water flow) are open in normal operation and closed to indicate irritation: container empty, low measuring water flow Main menu Service Info To look for the software version Main menu Service event log list In the event log list you find all irritations and alarms chronologic assorted max 100 events are stored. Original Bedienungsanleitung in deutsch - Version (V _01_09) 19/24

20 8 Maintenance All maintenance job shall be done by qualified personal. Need spare parts are to be supplied by the dealer. Please pay attention to the safety indications at the chemical containers and wear adequate protective clothes. Maintenance jobs to do: - clean filter if scaled - calibrate the ph- electrode at a difference >0,2pH against the measuring with Phenol-red - clean the inserts of the dosing valves especially the chlorine one every season or change if worn - change the dosing pump heads every season - change the seals of the redox-electrode every season 8.1 Filter The filter is to be cleaned if visually scaled. Especially in spring or autumn time it can be necessary more often. Advice! A scaled filter leads to a higher consumption of chlorine; the chlorine reacts with the organic material depressing the redox tension of the measuring water. Subsequently the chlorine concentration in the pool water will rise. 8.2 ph-electrode Attention! At doing any job with a ph-electrode pay attention that no humidity comes into contact with the connectors! Even smallest humidity will lead to a faulty electrode. The contacts must shine golden and may not look corroded. All sensors suffer under wear. The live time in swimming pool water should be at least one season, could be 2 years. With the time the performance of the electrode will change cause of scaling of the diaphragm and ageing of the sensor glass. This leads to deviations in the measuring value and a cleaning and calibration in needed. For cleaning the electrode only dunk it into the cleaning agent. Never use tiles or paper to clean the sensor glass and diaphragm. Advice! After each cleaning or change of the electrode you must calibrate it again. 8.3 Injection valves The yellow injection valve for chlorine solution tends to be blocked by calcium incrustations. Depending on the water factors temperature and calcium hardness a cleaning can be necessary within weeks or months. The sign for the need of cleaning is the blockage of the chlorine dosing and subsequently indication of chlorine low alarm. It is recommended to clean the injection valve frequently to avoid blockage of the dosing and stress/shorter life time of the pump. The calcium incrustation can be easily dissolved by hydrochloric or acetic acid. 1 Teflonband The parts 1, 3, 4, 5 und 6 are assembled ina maintenance kit. Advice Please pay attention to the right assembly of the parts. Otherwise you will have irritations in the function. Original Bedienungsanleitung in deutsch - Version (V _01_09) 20/24

21 snap lock 8.4 Dosing heads The pump heads should be changed yearly to be sure that under the season all is running well. To loosen the head press the snap locks at side of the head and pull the head off the motor shaft. Cut the black cable clips at the hose nipples and pull off the hoses from the nipples. Push on the hoses of the new dosing head onto the nipples and fix them with the cable clips. Now push on the dosing head onto the motor shaft till it does klick. 8.5 Redox-electrode Change yearly the flat seal of the inner platinum electrode and the O-ring. 9 Diagnosis and troubleshooting 9.1 check of dosing function if you have alarm on high ph-value or low redox obviously the dosing is interrupted. Go to menu point output test and choose the corresponding one. If the pump rollers turn the liquid shout be sucked up to the pump and further to the injection valve. You can see that by air bubbles in the transparent suction tube. If the roller does not move, the motor or any connection wire is broken. 9.2 Check of the electrodes Frequently you should measure the quality of your pool water by means of the analytic check kit. If you get greater deviations at the measuring values more often you should do a calibration job on this electrode. At this procedure you get information on the quality of the electrode. 10 taking out of operation hibernation - storage When the POOLKLAR is taken out of service for a longer time you do the following. - Flush all parts being in contact with the chemical with water. For this place a bin with water instead of the chemical container and let the pumps run by using the output test programmes for the pumps. Do this twice for both pumps. Then pull off the pump heads from the motor shaft. - The diaphragm of a glass electrode should never get dry. To avoid this, do some electrolyte into the protection cap and push it on the glass electrode. The ph-electrode is frost proove till -15 C. - Don t disconnect the mains supply; do not switch off the POOLKLAR. - If you get frost in your technical room, you have to empty all water leading parts of the system thoroughly. An alternative could be to dismount the POOLKLAR from the wall and place it at a frost safe room. 11 Technical data measures: electrics: dosing capacity: measuring range: width: 430mm voltage: 230V 50Hz peristaltic pump SR10 ph ph hight: 650mm currant: max. 4A mv mv depth: 150mm power: 7W stand by each pump approx. temperature C weight: 8kg 8W dosing 1l/h pressure ,6 bar Original Bedienungsanleitung in deutsch - Version (V _01_09) 21/24

22 12 Commissioning form doing Reset in the main menu all parameters are set back to the works settings. To be able to set the old, well proved parameters it is recommended to fill the list below with your special found parameters! After a reset the electrodes are to be calibrated again! Menu Settings works settings setting ranges steps at commissioning optimised Parameter ph - set point 7,0 ph 6,0 8,0 ph 0,05 - control range 0,50 0,1 1,0 0,1 - alarm high 8,0 ph 6,0 9,9 ph 0,1 - alarm low 6,5 ph 4,0 8,0 ph 0,1 - monitoring time 30 Minuten off 60 Min 2 Parameter Desinfektion/redox/mV - set point 750 mv mv 5 - control range 100 mv alarm high 800 mv mv 10 - alarm low 600 mv mv 10 - monitoring time 30 Minuten off 60 Min 2 Dosing capacity - Dosing capacity acid 100% % 10 - Dosing capacity chlorine 100% % 10 - cycle time 120 Sekunden sec 30 Parameter temp. C - set point 25 C C 1 - control range off 1 10 K 1 - alarm high 30 C C 1 - alarm low 10 C 5 50 C 1 - Offset (calibration) off -5 C C 1 Parameter pressure - backwash indication at 0,80 bar off 1,6 bar 0,01 times - dosing delay 600 Sekunden sec 10 System password Additional remarks: Date place service man operator Original Bedienungsanleitung in deutsch - Version (V _01_09) 22/24

23 13 Spare parts list Spare parts for the POOLKLAR you get from your dealer. To avoid misunderstandings please state for each demand the exact product designation and the series no. of the POOLKLAR. Blue signed code numbers suffer under normal wear and are excluded from the 2-years warranty time. dosing technics code no. article designation dosing head SR10 3,0mm white rolls motor for dosing pump SR hose holder kit SR10-XL maint. kit for inj. valve red, code no injection valve 3/8 4x1 yellow suction lance NF d16x500 2m yellow suction lance NF d16x500 2m red injection valve 3/8 4x1 red maint. kit for inj. valve yellow, code no measuring water electrodes code no measuring water ball valve PVC ¼ 6x1mm probe water take off valve PVC ¼ filter cup for fine filter 300µm seal for cap fine filter 300µm filter element fine filter 300µm switch tube POOLKLAR 1/4"-d16-NO switch body magnetic d11 for flow switch flow switch d8 1m measuring cell POOLKLAR PR screen inset 18mm for metering cell ph/orp dosing tube double T-piece 3/8" code no ph-electrode 55mm gelous electrolyte prode cable ph with screw-socket S7-80 cm redox electrode platinum 1/2" with seals kit seal kit for redox electrode 1/2" electrode insert Pt for redox elektrode 1/2" cable for redox electrode 1/2" - 90 cm cleaning beads 5 ml buffer solution ph 4,00-50 ml buffer solution ph 7,00-50 ml buffer solution redox +468mV 50 ml electrode cleaner solution 50 ml destillated water 500 ml control system code no. on request OPTIONS code no immersion sleeve PVC ½ x 60mm pressure sensor 0-1,6 bar for POOLKLAR-XL temperature sensor C Original Bedienungsanleitung in deutsch - Version (V _01_09) 23/24

24 14 Own notes Here you have the possibility to note your remarks e.g. special experience, maintenance works Original Bedienungsanleitung in deutsch - Version (V _01_09) 24/24