How to Convert a Universal Starter Box for Revo 3.3/Platinum
|
|
- Esmond Oliver
- 5 years ago
- Views:
Transcription
1 How to Convert a Universal Starter Box for Revo 3.3/Platinum These are instructions for converting a common universal electric starter box for starting the Revo 3.3 or Platinum without an on-board starting system. Written By: Brian Sallee 2017 traxxas.dozuki.com Page 1 of 14
2 INTRODUCTION Creating your own starting system for the Revo 3.3 or Platinum can be very useful if your vehicle does not have an on-board starting system. In just one half hour you can create your own starter box using a stock E-Maxx Chassis. TOOLS: Drill (1) Phillips Screwdriver (1) Protective Eyewear (1) Rotary Cutting Tool (1) PARTS: Stock E-Maxx chassis (1) 40mm Spacer (1) 2017 traxxas.dozuki.com Page 2 of 14
3 Step 1 Starter Box Prep Remove lid - Disconnect the starter box lid by removing the two hinge screws and locknuts. Remove charge jacks - The charge jacks will need to be removed to make room for the electric starter motors. They can be relocated by drilling new holes approximately 1/2-inch below the original ones. If the charge jacks are not necessary, then they can be removed permanently Step 2 Elevate starter wheel The starter wheel assembly must be elevated approximately 40mm to reach the Revo's flywheel. Disconnect the starter motor wires - The starter motors must be disconnected from the wiring harness to remove the starter motor assembly. Remove the starter motor assembly - Remove the four screws from the bottom of the starter box and lift the starter motor assembly from the box. Lift the starter motor assembly from the starter box traxxas.dozuki.com Page 3 of 14
4 Step 3 Raise starter motor assembly 40mm. Attach a 40mm spacer to the bottom of the starter motor assembly and remount the assembly back into the box. Longer hardware will be needed Make sure that the hardware you use is the correct size for your particular box. 1 large spacer or 4 individual spacers will work. Just make sure that the mounted motor assembly is secure. Tip: A wooden 2x4 cut to fit inside the box will also work. Note: Make sure you leave enough room for the battery wires to pass through traxxas.dozuki.com Page 4 of 14
5 Step 4 Trim the lid to clear raised motor assembly The wheel opening in the starter box lid must now be trimmed to provide clearance to the elevated motor assembly. The opening must be widened to approximately 40mm in width. This may vary with different starter boxes. Make sure there is proper clearance for the starter wheel. Remount the box lid - Use the two hinge screws and lock nuts to secure the lid to the starter box. Check the clearance for the starter wheel. Note: Do not tighten these screws. The lid needs to pivot smoothly to operate traxxas.dozuki.com Page 5 of 14
6 Step 5 Install posts to line up the flywheel with the starter wheel The Revo must be set onto the starter box in a specific location and orientation so that the flywheel lines up with the starter wheel for easy starting. There are multiple ways to key the truck onto the starter lid. OPTION A: Install plastic body posts - Universal plastic body posts can be used to mount onto the lid to key the truck in. Trim the posts to 1/2- inch in length. Correct post location - Refer to the picture for correct post locations for the Revo 3.3. The Post positions are marked in red and are measured from the center of the starter wheel to the center of the post location(s). Note: The positions indicated in the picture may need small adjustments for best performance from your personal Revo 3.3 and starter box. (A) Drill a hole here to mount a post to keep the front skid plate from sliding back. (B) Use this slot closest to the wheel. The slot may need to be lengthened a bit to fit the rear skid plate traxxas.dozuki.com Page 6 of 14
7 Step 6 OPTION B: Use front and rear E-Maxx chassis sections for 'drop-on' starting - The front and rear center sections of the molded E-Maxx chassis work great for keying in the Revo 3.3. The front center section of the E-Maxx chassis works great for a front adapter. Cut out the section along the lines shown in the picture with a rotary cutoff tool. Caution: Use proper protective eyewear when operating a rotary tool. Remove any unnecessary material from the adapter traxxas.dozuki.com Page 7 of 14
8 Step 7 Use these two holes for mounting the adapter. Use these locations for mounting the front adapter. The slot on the right will need to be notched for the outside screw traxxas.dozuki.com Page 8 of 14
9 Step 8 Mount Front Adapter Use the existing screws from the starter box to mount the front adapter onto the lid. (A) The left side hole in the adapter should line up at the end of the slot. (B) The right side hole in the adapter should be positioned in the outside slot, directly across from the left. The slot may need to be notched to fit the screw. Secure the adapter with the screws supplied with the starter box. Step 9 Correct Location and Orientation of the Front Adapter Double check the location of your front adapter. It should be aligned like the front adapter in these photos traxxas.dozuki.com Page 9 of 14
10 Step 10 Rear Adapter Cut out the section along the lines shown in the picture with a rotary cutoff tool. Caution: Use proper protective eyewear when operating a rotary tool. Remove any unnecessary material from the adapter. Use these two holes for mounting the adapter. Step 11 Use this slot for the rear adapter. The end of the slot at the side of the lid may need to be lengthened a little for proper fit traxxas.dozuki.com Page 10 of 14
11 Step 12 Mount Rear Adapter Use the existing hardware from the starter box to mount the rear adapter onto the lid. Step 13 Completed Starter Box Conversion Your starter box should look something like this traxxas.dozuki.com Page 11 of 14
12 Step 14 Correct starter wheel rotation for Revo The engine flywheel rotates counterclockwise (as you're looking at the front of the engine). The starter wheel needs to rotate clockwise in relation to the flywheel. If your wheel rotates the wrong way, just switch electric motor leads to get the proper rotation traxxas.dozuki.com Page 12 of 14
13 Step 15 Starting Your Revo 3.3 with the Converted Starter Box Fill the fuel tank with fuel and turn on the radio system. Set the truck onto the box while keying in the front and rear of the truck between the posts. The flywheel should line up with the starter wheel just above the wheel. The rear skid plate should fit between the two adapter posts and just in front of the lower rear suspension arms. The front skid plate should fit between the two posts and push back against the back wall of the adapter. The flywheel should line up with the starter wheel - just above the starter wheel traxxas.dozuki.com Page 13 of 14
14 Step 16 Starting Up Use a glow plug igniter to preheat the glow plug. Press down on the truck to engage the flywheel with the spinning starter wheel. The engine should turn over rapidly until the engine starts. This document was last generated on :56:13 AM traxxas.dozuki.com Page 14 of 14
LIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions
LIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions LIFT-304 LIFT-104 Contents of LIFT-304/104 Yamaha G22 Lift Kit: a (1 ea.) Passenger Side Spindle
More informationPA Performance High Torque Starter Solenoid Installation Instructions
PA Performance High Torque Starter Solenoid Installation Instructions Introduction: If you are having issues with your starter related to your solenoid, the PA Performance High Torque Starter Solenoid
More informationINSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only)
INSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No. 61770 for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only) Warn Light Bar 61090 and many other grille guards can be mounted
More informationThese instructions were written for a North American specification MkVI Golf R. Other models are similar.
Notes: These instructions were written for a North American specification MkVI Golf R. Other models are similar. When disassembling the car, be sure to keep all fasteners so they can be reused. It is recommend
More information07-11 GM 4WD 1500 P/U 1 1/4 Body Lift
92RC70100 07-11 GM 4WD 1500 P/U 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationPARTS LIST: 8581 DODGE LONG ARM BRACKETS 03-13
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8580 03-12 DODGE 2500/3500 4X4, 06-08 1500 MEGACAB 4X4 LONG ARM SUSPENSION KIT V3.0 GENERAL NOTES: These instructions are also available
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationAir Lift. Kit Honda Civic (8th GEN) PERFORMANCE INSTALLATION GUIDE. Front Application
Air Lift PERFORMANCE Kit 78524 Honda Civic (8th GEN) Front Application INSTALLATION GUIDE PERFORMANCE SUSPENSION PARTS For maximum effectiveness and safety, please read these instructions completely before
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationMOUNT BRACKET PARTS and HARDWARE: Installation parts with * come loose in hardware kit bag. Other parts are preassembled
INSTALL INSTRUCTIONS C-DMM-2006 Dash Monitor Mount 2017-2019 F-250, 350, 450 Pickup, F-450 and 550 Cab Chassis, 2015-2019 Ford F-150 and 2018-2019 Expedition Notes: 1. The C-DMM-2000 series Dash Monitor
More informationSuper Duty Front Air Bag Installation Instructions
2005-2010 Super Duty Front Air Bag Installation Instructions Congratulations! You have just purchased the best engineered, highest quality front air suspension kit available on the market for your 2005-2010
More informationInstallation Instructions
Installation Instructions Eibach Springs, Inc. 264 Mariah Circle Corona, California 92879-1751 USA Tech Support 800-222-8811 Ext 114 Eibach-Callaway Multi-Pro Coil-Overs 1997-2007 Chevrolet Corvette All
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More informationAir Lift. Kits PERFORMANCE / /78637 BMW E36, E46 Chassis Rear Application (With and Without Shocks) INSTALLATION GUIDE
Air Lift PERFORMANCE Kits 75636/78636 75646/78637 BMW E36, E46 Chassis Rear Application (With and Without Shocks) INSTALLATION GUIDE PERFORMANCE SUSPENSION PARTS For maximum effectiveness and safety, please
More informationJakes Big Block Conversion Kit (P/N 7216)
Jakes Big Block Conversion Kit (P/N 7216) Before beginning be sure to read and understand the instructions. This kit is designed to give you maximum torque for those extreme off-road conditions. We thank
More information»Product» Safety Warning
#J9320, J9321 Installation Instructions 1986-1995 Jeep YJ 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1i update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1i update Pedal box...1 Cable Accelerator Pedal (2002-2005)...2 OEM seats...7 Windshield... 13 Center console... 19 Pedal box Attach the pedal
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner.
More informationInstallation instructions for Camaro/Firebird and Nova* Windshield Wiper Systems
Installation instructions for 1967-69 Camaro/Firebird and 1968-74 Nova* Windshield Wiper Systems The Raingear 1967-69 Camaro/Firebird and 1964-74 Nova wiper system is designed for ease of installation
More informationJEEP WRANGLER INSTALLATION INSTRUCTIONS KIT SUM
1986-1995 JEEP WRANGLER INSTALLATION INSTRUCTIONS KIT SUM-7893300 Installation of a body lift will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationCOIL-OVER SUSPENSION SYSTEM
Page 1 of 11 PART NUMBER: 220.50.631X, 220.60.631X INSTRUCTION SHEET NUMBER: 920.65.9800A COIL-OVER SUSPENSION SYSTEM APPLICATION: 1997-2013 CORVETTE PACKAGE CONTENTS: Coil-Over Assembly - Front Right
More informationINSTALLATION INSTRUCTIONS
HIGH FLOW AIRFLOW METER INSTALLATION INSTRUCTIONS PART NUMBER D763-1600A APPLICATION: 2001-06 E46 M3 Parts List: Hose clamp 64Z (7) Plastic Rivets Air Filter Temp Sensor & Harness (2) Button Head Screws
More informationEVO-1162 EVO Tailgate Tire Carrier
EVO-1162 EVO Tailgate Tire Carrier Bill of Materials EVO-1162 Tailgate Tire Carrier Part number Description Quantity EVO-12161 EVO Tailgate Tire Carrier 1 EVO-12162 Bolt Plate 1 EVO-12163 Wheel Mount 1
More informationWARNING NOTICE CAUTION ASSEMBLY INSTRUCTIONS
MODEL 284 EZ-GLIDE SYSTEM 10' HIGH CUBE VAN DRIVER SIDE ALUMINUM DROP DOWN LADDER RACK ATTENTION Read and understand all instructions and warnings before operating or using this product. WARNING This product
More informationBODY-24, Late Model 944 ( and Newer) Dash Replacement
BODY-24, Late Model 944 (1985.5 and Newer) Dash Replacement Introduction Replacing the dash in a late model 944 is not overly difficult. However, it is very tedious and a lot of patience is required. It's
More informationLIFT-506 BMF Lift Kit Club Car DS Gas & Electric Installation Instructions
LIFT-506 BMF Lift Kit Club Car DS Gas & Electric 2003.5-09 Installation Instructions Contents of LIFT-506 Club Car DS BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1
More information1993 ACCESSORIES & EQUIPMENT Volkswagen Power Sun Roof. Volkswagen; Corrado SLC, EuroVan, Golf, GTI, Jetta, Passat
Article Text ARTICLE BEGINNING 1993 ACCESSORIES & EQUIPMENT Volkswagen Power Sun Roof Volkswagen; Corrado SLC, EuroVan, Golf, GTI, Jetta, Passat DESCRIPTION & OPERATION The power sun roof operates at all
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 6592 REAR HANGER & SHACKLE KIT DODGE RAM 2500 / 3500 Congratulations! You were
More informationInstallation Instructions
Installation Instructions for Harley Tri-Glide Trike Step 1 Step 2 Remove trike body and set aside Disassemble the rear suspension. Set aside the differential, ring gear, pulley, differential clamps, wheel
More informationJ & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034
J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The Hyperdrive Assault has gone through months
More information3 Rear Kit/Front Trimming. Chevy/GMC Tahoe, Avalanche Part#: ,
Part#: 021307, 021309 3 Rear Kit/Front Trimming Chevy/GMC Tahoe, Avalanche 2007-2016 Rev. 100416 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail:
More informationTNT Customs JK Guardian Front Bumper
Master Your Terrain (307) 775 9565 www.tntcustoms.com TNT Customs JK Guardian Front Bumper Please observe proper shop safety procedures when performing this install. Use proper eye and hearing protection
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationTuned Length Headers. Special Tools Required: Install Time: Difficulty: Follow these instructions carefully to ensure correct fitment and operation.
Special Tools Required: welder / saws all Install Time: Approximately 4 Hours Difficulty: 4 out of 5 Follow these instructions carefully to ensure correct fitment and operation. STEP 1 Disconnect the negative
More information9th Gen Honda Civic INSTALLATION GUIDE Civic, Civic Si Kit Civic Si Kit Front Application
9th Gen Honda Civic 2012-15 Civic, 2012-13 Civic Si Kit 78526 2014+ Civic Si Kit 78556 Front Application INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationPERFORMANCE SUSPENSION PARTS
PERFORMANCE SUSPENSION PARTS Introduction Air Lift Performance The purpose of this publication is to assist with the installation, maintenance and troubleshooting of this Chrysler LX, LD, LC Platform 300C,
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 6419 HANGER & SHACKLE KIT FORD F-150 Congratulations! You were selective enough
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----3300 W. Pontiac Way Clovis, CA 93612 toll free: 1-800-445-3767 web: www.belltech.com---- 6605-6607 FLIP KIT CHEVROLET C/K 1500 / 2500 PICK UP Thank you for being selective
More informationInstallation and Service Manual
RAVE Star Lift Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTRUCTIONS is required and will promote the safety of those installing this product, as well as those who
More informationII E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
II E1500-11 INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT KITS ARE UL LISTED UNDER CATEGORY GWVW, GWVW7 (CANADA) (ACCESSORY FOR USE ON FIRE EXIT HARDWARE AND PANIC HARDWARE). INDEX
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More information»Product» Safety Warning
D1401 Installation Instructions 2013 Ram 3500, 2014 Ram 2500 4.5" Radius Arm Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationWRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN
WRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE thoroughly and completely.
More informationRequired tools General hand tools 21/64" drill bit Torque wrench Threadlocker Center punch
Slipper Spring Kit (part numbers 2560, 2570 and 2580) Item Qty Part number Description 1... 8... 350054-50...3/8-16 x 1" grade 8 self-tapping screw 2... 4... 350084-00...7/16-14 x 4" grade 5 3... 6...
More informationShown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN
Shown with optional GFR-1017R Body Posts J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The
More information4 & 6 4-Link Suspension Systems. Ford Super Duty 4WD Part#: ,
Part#: 013013, 013014 4 & 6 4-Link Suspension Systems Ford Super Duty 4WD 2011-2016 Rev. 051817 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationLIFT-504. BMF Lift Kit. Yamaha G22 Gas or Electric. Installation Instructions
LIFT-504 BMF Lift Kit Yamaha G22 Gas or Electric Installation Instructions Contents of LIFT-504 Yamaha G22 BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More informationInstallation Instructions :AUDI 8V RS3 : Page 1
Installation Instructions :AUDI 8V RS3 : Page 1 1. We will start by removing the stock airbox system. Remove the 2 screws holding the inlet duct in place. Then push the duct into the airbox to release
More informationJEEP Wrangler JK/JKU Swing-A-Way Tire Carrier/RotoPpax WARNINGS/CAUTIONS NOTE. INSTALLATION INSTRUCTIONS 2 Door Models 85209
JEEP Wrangler JK/JKU Swing-A-Way Tire Carrier/RotoPpax 2007-2017 INSTALLATION INSTRUCTIONS Item Kit No. 2 Door Models 85209 4 Door Models 85209 WARNINGS/CAUTIONS These instructions are for both the can
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationToyota Tundra Tow Kit Installation Instructions
2007-2013 Toyota Tundra Tow Kit Installation Instructions Congratulations! You have just purchased the best engineered, highest quality air suspension kit available on the market for your 07-14 Toyota
More informationHASPORT PERFORMANCE EFH1
HASPORT PERFORMANCE Installation Instructions For: Part Number EFH1 1988-1991 Honda Civic/CRX Hasport Performance mounts are the result of extensive research and engineering. All mounts are designed with
More information97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions
97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Drill / Assorted Drill Bits Floor Jack Jack Stands Measuring
More informationEVO-1130 EVO MFG Pro Series JK Front Bumper
EVO-1130 EVO MFG Pro Series JK Front Bumper PART# DESCRIPTION QTY EVO-12071 EVO Pro Series Bumper w/ Hoop 1 EVO-12072 EVO Pro Series Bumper Winch Plate 1 EVO-12075 EVO Pro Series Bumper Winch Plate, Nut
More informationINSTALLATION INSTRUCTIONS 6298 Air Suspension Kit (pat. pending) Thank you for purchasing a quality Hellwig Product.
559-734-7451 800-367-5480 TechSupport@HellwigProducts.com INSTALLATION INSTRUCTIONS 6298 Air Suspension Kit (pat. pending) Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1970-74 Cuda/Challenger FOR PART NUMBER S: 1620810010, 1620810020, 1620810051, 1620820010, 1620820020, 1620820051 S I NCE 1986 Instruction # 8000000005
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More information05+ Toyota Tacoma Rear Shock Hoop Install Notes Part# 86460
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM 05+ Toyota Tacoma Rear Shock Hoop Install Notes Part# 86460 Note: This kit is designed to work with the Total
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More information07-11 GM 1500 Pickup, Avalanche, Yukon, Tahoe, Suburban Front 2.5 Kit
92130500 07-11 GM 1500 Pickup, Avalanche, Yukon, Tahoe, Suburban Front 2.5 Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install
More informationI. Before starting installation
5. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. A. Disconnect battery cables 1. Disconnect the negative cable first, then the
More informationLIFT-503. BMF Lift Kit. Club Car Precedent. Installation Instructions
LIFT-503 BMF Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-503 Club Car Precedent BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm (Shipped Loose)
More informationPolaris 340 & ATV Power Module Training and Troubleshooting Guide
Polaris 340 & ATV Power Module Training and Troubleshooting Guide Summary: This guide is intended as a training tool for the mechanical evaluation and troubleshooting of a 340 or ATV power module only.
More informationINSTALL INSTRUCTIONS
INSTALL INSTRUCTIONS Models: 6005 & 6005TK (For Non Electric Mirrors) GM CK Body Style If your stock mirrors are stock electric the wrong set has been ordered. Do not attempt to manually extend or retract
More informationEVO EVO Enforcer PRO Stage 1
EVO-201-1 EVO Enforcer PRO Stage 1 QTY PART # DESCRIPTION 1 EVO-11022B EVO Front Lower Control Arm, Driver 1 EVO-11023B EVO Front Lower Control Arm, Pass 1 EVO-11042B REARWARD BRACKET JK FRONT TRACKBAR
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More information»Product» Safety Warning
D1601 Installation Instructions 2013 Ram 3500, 2014 Ram 2500 6.5" Radius Arm Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will
More informationOWNER'S MANUAL FOR 135LB STAINLESS STEEL SPREADER SNOWRATOR
2017 OWNER'S MANUAL FOR 135LB STAINLESS STEEL SPREADER SNOWRATOR AES L. T. RICH PRODUCTS 11/16/2017 TABLE OF CONTENTS 1.0 SHIPPING CONTENTS... 2 2.0 IMPORTANT INFORMATION... 3 2.1 ABOUT THIS MANUAL...
More informationINSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT INDEX FUNCTION DESCRIPTION PAGE 1 PARTS LIST PAGE 2 TOOLS REQUIRED PAGE 2 KIT INSTALLATION INSTRUCTIONS PAGE 2-10 KIT ADJUSTMENT INSTRUCTIONS
More informationAir Lift. Kit Ford Mustang SN95 PERFORMANCE INSTALLATION GUIDE. Rear Application
Air Lift PERFORMANCE Kit 78619 Ford Mustang SN95 Rear Application INSTALLATION GUIDE PERFORMANCE SUSPENSION PARTS For maximum effectiveness and safety, please read these instructions completely before
More informationInstallation instructions for IPS parking Brake Kit for 1996 to 2002 Viper
Installation instructions for IPS parking Brake Kit for 1996 to 2002 Viper WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly
More informationFAX
INSTALLATION INSTRUCTIONS 6299 Air Suspension Kit (pat. pending) 2009+ Dodge 1500 Pickup with Rear Coil Springs Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationLincoln Mark VII Air Spring Solenoid Replacement By ArtBaileyJr
Lincoln Mark VII Air Spring Solenoid Replacement By ArtBaileyJr Removal and Installation of Air Spring Solenoid At some point, our Mark VII s will require air spring service. Most air spring service requires
More information»Product» Safety Warning
#C9315 Installation Instructions 2000-2005 Suburban/Tahoe/Yukon 1500 2/4wd 3" Body Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone
More informationPPM-8055/8089 JK FRONT TRACK BAR RELOCATION BRACKET Version 1.2
POLY PERFORMANCE MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8055/8089 JK FRONT TRACK BAR RELOCATION BRACKET Version 1.2 GENERAL NOTES: These instructions are also available on our
More informationLingenfelter Signature Series Camaro SS Rear Valance
Lingenfelter Signature Series 2010-2012 Camaro SS Rear Valance PN: L850161410 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-0422 fax www.lingenfelter.com
More informationLIFT Drop Spindle Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions
LIFT-107 6 Drop Spindle Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions Contents of LIFT-107 E-Z-Go RXV Drop Spindle Lift Kit: a (1 ea.) Driver Side Spindle b (1 ea.) Passenger Side Spindle
More informationFTS & 8 RADIUS ARM BOX KIT
FTS22139 6 & 8 RADIUS ARM BOX KIT 2008-2015 FORD F-250/350 SUPER DUTY 4WD 2008 2015 FORD F-250/350 SUPER DUTY 4WD FTS22139 6 & 8 RADIUS ARM KIT FTS22139 6"&8" Radius Arm Box Kit FT30287 Hardware Kit Qty
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationINSTRUCTION G-Comp Rear Suspension: Chevy Camaro. Kit Contents:
INSTRUCTION 350-700 G-Comp Rear Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350700.1 G-Comp Crossmember & Chassis Brace 350700.2 G-Comp Rear Crossmember Assembly 350700.3 G-Comp
More informationParts and tools needed for installation- Cleaning and Painting -
Thank you for the purchase of our JK Front Trail Doors. We have made these from 6061-T6 aluminum and reinforced them with stiffeners at the top that double as a comfortable armrest and support for Rugged
More informationRAM LIFT KIT PART# STOP! READ THIS FIRST!
NOTE: 2014-2016 RAM 2500 4 LIFT KIT PART# 54340 STOP! READ THIS FIRST! **READ THESE ENTIRE INSTRUCTIONS BEFORE STARTING ANYTHING** or chroming, which can damage the strength and structure of the metal,
More informationBUICK SKYLARK & GS CHEVROLET CHEVELLE & MONTE CARLO PONTIAC GTO & LEMANS OLDSMOBILE CUTLASS & 442
28433 HWY 65 NE ISANTI, MN 55040 763-444-5880 800-828-2212 www.autocityclassic.com 1970-1972 GM A-BODY 2DR COUPE, INSTALLATION HARDTOP & CONVERTIBLE INSTRUCTIONS POWER WINDOW INSTALL KIT BUICK SKYLARK
More informationKAWNEER 1686 CONCEALED EXIT DEVICE
FEBRUARY, 2015 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl
More informationWARNING indicates a potentially hazardous situation which, if not avoided, could result in property damage, serious personal injury or even death.
Comfort Ride Third axle slipper leaf spring system (part numbers 2560-50, 2570-50 and 2580-50) and shock absorber system (part numbers 2450-50, 2460-50 and 2470-50) Installation Instructions All specifications
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2000 by B&M Racing & Performance Products LLC The B&M Unimatic is a universal shifter that will
More information