Model FSB-110 Multiple Vertical Table Stand

Transcription

1 Model FSB-110 Multiple Vertical Table Stand INSTALLATION MANUAL 1x #8-32 1x 3/32" (2.38mm) 1/8" (3.15mm) Rev B. 08/02 1 of CH

2 1 ERGONOMIC EYE HEIGHT RECOMMENDATIONS Vertically stacked Flat Panel monitors do not lend themselves to standard Ergonomic Height Rules, but generally, the bottom monitor(s) should be set low, as close to the worksurface as possible because it is more comfortable to look down than to look up for sustained periods. 6" (1168mm) 62" (1575mm) Average Female Average Person Eye Standing 59'' (1509 mm) 62'' (1567 mm) Height Sitting '' (1118 mm) 6'' (1171 mm) Center of Operating Range 5'' (1377 mm) 5'' (1377 mm) Average Male 6'' (1636 mm) 8'' (1232 mm) 5'' (1377 mm) 2 3! 1/8" (3.15mm) 888-CH of 9 Rev B. 08/02

3 1 75mm 2 100mm 3 Xmm 3 Contact Chief Manufacturing 1 75mm! If your monitor uses a screw size other than M x 10mm, DO NOT use the M x 10mm screws or knob provided as they could result in damage to the monitor. Indien uw monitor voorzien is van een ander type schroef dan de M X 10 mm, gebruik dan beslist niet de door Ergotron geleverde M X 10mm schroeven of schroefknoppen, want deze kunnen de monitor beschadigen. Rev B. 08/02 3 of CH

4 2 100mm 3/32" (2.38mm)! mm #8-32 a! If your monitor uses a screw size other than M x 10mm, DO NOT use the M x 10mm screws or knob provided as they could result in damage to the monitor. Indien uw monitor voorzien is van een ander type schroef dan de M X 10 mm, gebruik dan beslist niet de door Ergotron geleverde M X 10mm schroeven of schroefknoppen, want deze kunnen de monitor beschadigen. b 888-CH of 9 Rev B. 08/02

5 5 6 5a 5b 6a 7 6b Rev B. 08/02 5 of CH

6 OVERVIEW The Monitor Pivots are factory-set to provide positive pivot control and a smooth moving force throughout the entire pivot range of motion. To customize your installation, you will evaluate the operation of each Pivot function by moving the monitor through its full range of movement. If excessive force is required to pivot the monitor or if the monitor does not stay in the desired position, pivot adjustment is required. Adjust for a controlled motion of the monitor over the entire range of travel. Specifi c adjustment procedures for each function are found on the following pages. a b c a a1 a2 a3 888-CH of 9 Rev B. 08/02

7 b b1 b2 b3 c c1 c2 c3 Rev B. 08/02 7 of CH

8 ? TROUBLE SHOOTING a b c Symptom Probable Cause Solution Monitor pivots up and down too diffi cult or too easy Improper Pivot tension Monitor exceeds weight capacity* Contact Chief Manufacturing a 6 Monitor pivots side-to-side too diffi cult or too easy Improper Pivot tension b 7 Monitor rotates from portrait to landscape too diffi cult or too easy Improper Pivot tension c 7 * Weight Capacities: Generally (although there are many variables), the weight capacity is a function of the center of gravity (CG) of the monitor relative to the Pivot Mounting Pad. 23 lbs (10.5 kgs) is based on the CG not exceeding 1" (2.5mm) from the Pivot Mounting pad. For every 1" additional distance between the CG of the monitor and the Pivot Mounting Pad reduce the capacity by 3.5 lbs (1.59 kgs). up to 23 lbs (up to 10.5 kgs) 888-CH of 9 Rev B. 08/02

9 SPECIFICATIONS Part Number Description Weight Capacity Net Weight Shipping Weight FSB-110 Multiple Vertical 23 lbs (10kg) per pivot 16.5 lbs (7.5kg) 19 lbs (8.62kg) Table Stand RANGE OF MOTION up to 180 monitor tilt (side view) up to 180 side-to-side tilt (top view) 360 portrait/landscape (P/L) (front view) DIMENSIONS 1 1 /2" (38 mm) 6" (152. mm) 28 1 /" (718 mm) 12 3 /8" (31 mm) REPLACEMENT PARTS Contact your Chief Manufacturing representative for details Chief Manufacturing Inc Hwy 13 S., Ste. 500 Savage, MN USA Phone: Fax: Rev B. 08/02 9 of CH