IFP BMG HIGH TORQUE High Performance in an Economical Package International BMG series motors are economical efficient compact units designed for medium duty applications requiring smooth control of shaft speed and rotation while maintaining maximum output torque. Motors operate using an efficient "Gerotor" assembly suitable for applications requiring higher torque for short periods of time and lower torque for longer periods of time. When operated within their rated conditions these motors will provide long trouble free service life. C:\wliu\BMG.bmp Features High Volumetric Efficiency Economical High Starting Torque Compact BMG - 30-2 - S K Series Displacement Mounting Porting Shaft Mounting 2 SE 2 Bolt 4 4 Bolt (3.25" BC) K S Shaft 1" keyed 1" 6B Spline S P B Porting 7/8" -14 SE 1/2" NPT 1/2" BSP Displacement 3 3 in /r (cm /r) Speed (rpm) Flow GPM (l/min) Torque in-lbs(nm) 30 3.0(50) 700 880 10.6(40) 49 4.9(80) 550 715 61 6.1(100) 440 570 76 7.6(125) 350 450 98 9.8(160) 275 360 122 12.2(200) 220 300 152 15.2(250) 176 230 192 19.2(315) 150 180 244 24.4(400) 130 150 Pressure PSI (MPa) 620(70) 800(90) 1000(110) 1250(140) 1300(145) 1600(185) 1600(175) 1750(195) 2000(230) 2600(300) 2200(245) 2800(320) 2500(278) 3500(400) 2800(315) 4000(450) 3350(378) 4000(450) 1800(124) 1800(124) 1800(124) 2300(159) 2300(159) 2300(159) 1800(124) 1600(110) 2300(159) 2300(159) 1600(110) 1400(97) 1300(90) 1800(124) 1200(83) 1400(97)
IFP BMG HIGH TORQUE Ø1.75/1.745(44.45/44.32) Pilot Dia. 45 Ø0.540/0.530(13.62/13.46) Dia. thru(2) Mounting Holes 5.17(131.4)Max. Ø3.25/3.245(82.55/82.44) Pilot Dia. 3.28(83.3) Max 1.76(44.7) Max 3/8-16UNC(0.60(15.2) Max bolt engagement) Mounting holes(4) equally spaced on 3.25(82.6) Dia. bolt circle 0.11(2.8) Groove provided for 3.25(82.5)D. x 0.103(2.52) Cross section O ring 4.187(106.35) 1.64(42.7) 0.998/0.996 (25.35/25.3) 1/4-20 UNC-2Bx0.56 (14.2) Min Deep 0.60(15.5) 7/8-14 UNF O Ring port 1.81/1.75 (46.0/44.5) 1.00(25.41) Min. W mounting surface 1.114/1.098 (28.30/27.89) 1.000/0.992(25.4/25.15) Dia. key x 0.251/0.25 (6.375/6.35) wide G1/4 (Optional drain port) 0.247/0.2444 (6.275/6.200) Ø0.848/0.843 (21.54/21.40) 25.4/25.37 (1.00/.999) Dimension inches(millimeters) 1"SE -6B Spline Shaft 1" Woodruff Keyed Shaft Displ. in 3/r (cm 3/r) 3.0 (50) 4.9 (80) 6.1 (100) 7.6 (125) 9.8 (160) 12.2 (200) 15.2 (250) 19.2 (315) 24.4 (400) W width in(mm) 0.28 (7) 0.41 (10.5) 0.51 (13) 0.63 (16) 0.83 (21) 1.02 (26) 1.26 (32) 1.65 (42) 2.04 (52) L Length in (mm) 5.54 (140.7) 5.68 (144.2) 5.78 (146.7) 5.89 (149.7) 6.09 (154.7) 6.28 (159.7) 6.52(165.7) 6.92 (175.7) 7.31 (185.7) Weight (4 bolts/ 2 Bolts) Weight lbs (kg) 13.01/13.22 (5.9/6.0) 13.22/13.56 (6.0/6.15) 13.22/13.67 (6.0/5.2) 13.56/13.78 (6.15/6.25) 13.78/14.44 (6.25/6.55) 14.11/14.66 (6.4/6.65) 14.77/15.32 (6.7/6.95) 15.76/16.20 (7.15/7.35) 16.53/16.98 (7.5/7.7)
IFP HIGH TORQUE GEROTER MOTORS Parts Service Information "BMG SERIES" Screw Spacer Plate Housing Drive Plug Pin Geroter Back Cover Woodruff Key Spacer Front Cover (2 bolts) Thrust Needle Bearing Plug "O " Ring " O " Ring Bearing Race Keyed Shaft (Spline Shaft vailable) Thrust Needle Bearing Shaft Seal Screw Front Cover (4 bolt) C FCTORY TIMING OF MOTOR WILL PRODUCE FOLLOWING ROTTIONS WHEN INLET ND OUTLET PORTS RE ORIENTTED S SHOW S BOVE DIGRMS
IFP BMG HIGH TORQUE *INDICTES STNDRD STOCK UNITS STNDRD 4 BOLT/KEYED SHFT(SPLINE SHFTS VILBLE) IFP MODEL BMG030-4PK *BMG030-4SK 3.0 BMG030-4PK *BMG030-4SK 3.0 BMG049-4PK *BMG049-4SK 4.9 BMG061-4PK *BMG061-4SK 6.1 BMG076-4PK *BMG076-4SK 7.6 BMG098-4PK *BMG098-4SK 9.8 BMG122-4PK *BMG122-4SK 12.2 BMG152-4PK *BMG152-4SK 15.2 BMG192-4PK *BMG192-4SK 19.2 BMG244-4PK *BMG244-4SK 24.4 CHRLYNN "H" MODEL 101-1749 101-1753 2.2 101-1009 101-1001 2.8 101-1750 101-1754 3.6 101-1002 101-1010 4.5 101-1003 101-1011 5.9 101-1755 101-1751 7.3 101-1752 101-1756 8.9 101-1004 101-1012 9.7 101-1005 101-1013 11.3 101-1006 101-1014 14.1 101-1007 101-1015 17.9 101-1008 101-1016 22.6 DNFOSS "OMP" MODEL 151-2041 151-2121 3.0 151-2041 151-2121 3.0 151-2122 151-2042 4.7 151-2123 151-2043 5.9 151-2124 151-2044 7.6 151-2125 151-2045 9.5 151-2026 151-2046 11.9 151-2127 151-2047 14.8 151-2128 151-2048 18.7 151-2129 151-2049 23.7 PORTS SIZE STNDRD 2 BOLT/KEYED SHFT(SPLINE SHFTS VILBLE) IFP MODEL BMG030-2PK *BMG030-2SK 3.0 BMG030-2PK *BMG030-2SK 3.0 BMG049-2PK *BMG049-2SK 4.9 BMG061-2PK *BMG061-2SK 6.1 BMG076-2PK *BMG076-2SK 7.6 BMG098-2PK *BMG098-2SK 9.8 BMG122-2PK *BMG122-2SK 12.2 BMG152-2PK *BMG152-2SK 15.2 BMG192-2PK *BMG192-2SK 19.2 BMG244-2PK *BMG244-2SK 24.4 CHRLYNN "H" MODEL 101-1704 101-1700 2.2 101-1025 101-1033 2.8 101-1705 101-1701 3.6 101-1026 101-1036 4.5 101-1027 101-1035 5.9 101-1706 101-1702 7.3 101-1707 101-1703 8.9 101-1028 101-1036 9.7 101-1029 101-1037 11.3 101-1030 101-1038 14.1 101-1031 101-1039 17.9 101-1032 101-1040 22.6 DNFOSS "OMP" MODEL 151-2081 151-2001 3.0 151-2084 151-2001 3.0 151-2082 151-2002 4.7 151-2083 151-2003 5.9 151-2084 151-2004 7.6 151-2085 151-2005 9.5 151-2086 151-2006 11.9 151-2087 151-2007 14.8 151-2088 151-2008 18.7 151-2089 151-2009 23.7 PORTS SIZE
IFP BMG HIGH TORQUE TIMING PROCEDURE STNDRD ROTTION Motor rotation will be as shown in Figure #1 when the following timing procedure is used. Position tooth slot#1 on shaft assembly in line with tooth slot#3 highest point of geroter - VIEW GEROTER HIGHEST POINT TOOTH SLOT #3 TOOTH SLOT #1 C SHFT ROTOR Figure #1 When timing is orientated as shown TIMING PROCEDURE REVERSE ROTTION Motor rotation will be as shown in Figure #2 when the following timing procedure is used. Position tooth slot#2 on shaft assembly in line with tooth slot#3 highest point of geroter GEROTER HIGHEST POINT - VIEW TOOTH SLOT #3 TOOTH SLOT #2 SHFT ROTOR C Figure #2 When timing is orientated as shown
IFP BML HIGH TORQUE High Performance in an Economical Package International BML series motors are economical efficient compact units designed for continuous duty applications. Motors operate using an efficient Geroter / Roller assembly for applications requiring higher torque and operating pressure, the roller assembly provides a wear compensating power element for higher volumetric efficiency and a longer life. When operated within their rated conditions these motors will have a long trouble free service life. Features High Volumetric Efficiency Economical High Starting Torque Compact BML - 30-2 - S K Series Displacement Mounnting Porting Shaft Mounting 2 SE 2 Bolt 4 4 Bolt (3.25" BC) K S Shaft 1" keyed 1" 6B Spline S P B Porting 7/8" -14 SE 1/2" NPT 1/2" BSP Displace 3 3 in /r (cm /r) Speed (rpm) Flow GPM (l/min) Torque in-lbs(nm) Pressure PSI (MPa) 30 3.0(50) 760 950 10.6(40) 750(80) 1000(110) 2500(172) 49 4.9(80) 650 815 1150(130) 1500(170) 2500(172) 61 6.1(100) 520 650 1500(170) 1900(215) 2500(172) 76 7.6(125) 420 520 1900(210) 2350(265) 2500(172) 98 9.8(160) 320 407 2200(250) 2650(300) 1800(124) 2200(152) 122 12.2(200) 260 330 159(60) 2550(290) 3350(380) 1800(124) 2200(152) 152 15.2(250) 210 260 2650(300) 3800(430) 1400(99) 192 19.2(315) 165 207 2800(320) 4250(480) 1200(83) 1800(124)
IFP BML HIGH TORQUE Ø1.75/1.745(44.45/44.32) Pilot Dia. 45 Ø0.540/0.530(13.62/13.46) Dia. thru(2) Mounting Holes 5.17(131.4)Max. Ø3.25/3.245(82.55/82.44) Pilot Dia. 3.28(83.3) Max 1.76(44.7) Max 3/8-16UNC(0.60(15.2) Max bolt engagement) Mounting holes(4) equally spaced on 3.25(82.6) Dia. bolt circle 0.11(2.8) Groove provided for 3.25(82.5)D. x 0.103(2.52) Cross section O ring 4.187(106.35) 1.64(42.7) 0.998/0.996 (25.35/25.3) 1/4-20 UNC-2Bx0.56 (14.2) Min Deep 0.60(15.5) 7/8-14 UNF O Ring port 1.81/1.75 (46.0/44.5) 1.00(25.41) Min. W mounting surface 1.114/1.098 (28.30/27.89) 1.000/0.992(25.4/25.15) Dia. key x 0.251/0.25 (6.375/6.35) wide G1/4 0.11 (3) 0.247/0.2444 (6.275/6.200) Ø0.848/0.843 (21.54/21.40) 25.4/25.37 (1.00/.999) Dimension inches(millimeters) 1"SE -6B Spline Shaft 1" Woodruff Keyed Shaft Displ. in 3/r (cm 3/r) 3.0 (50) 4.9 (80) 6.1 (100) 7.6 (125) 9.8 (160) 12.2 (200) 15.2 (250) 19.2 (315) W width in(mm) 0.39 (10) 0.63 (16) 0.79 (20) 0.98 (25) 1.24 (31.5) 1.57 (40) 1.97 (50) 2.44 (62) L Length in (mm) 5.74 (145.7) 5.97 (151.7) 6.31 (155.7) 6.33 (160.7) 6.58 (167.2) 6.92 (175.7) 7.31(185.7) 7.78 (197.7) Weight (4 bolts/ 2 Bolts) Weight lbs (kg) 15.43/15.98(7.00/7.25) 15.98/16.53 (7.25/7.50) 16.53/17.09 (7.50/7.75) 17.09/17.64 (7.75/8.00) 18.08/18.74 (8.20/8.50) 18.85/19.51 (8.55/8.85) 20.39/21.27(9.25/9.65) 21.27/22.05 (9.25/9.65)
IFP HIGH TORQUE GEROTER / ROLLER MOTORS Parts Service Information "BML SERIES" Screw Spacer Plate Housing Drive Plug Pin Geroler Back Cover Woodruff Key Spacer Front Cover (2 bolts) Thrust Needle Bearing Plug "O " Ring Spacer " O " Ring Bearing Race Keyed Shaft (Spline Shaft vailable) Thrust Needle Bearing Shaft Seal Screw Front Cover (4 bolt) C FCTORY TIMING OF MOTOR WILL PRODUCE FOLLOWING ROTTIONS WHEN INLET ND OUTLET PORTS RE ORIENTTED S SHOW S BOVE DIGRMS
IFP BML HIGH TORQUE *INDICTES STNDRD STOCK UNITS STNDRD 4 BOLT/KEYED SHFT(SPLINE SHFTS VILBLE) IFP MODEL BML030-4PK *BML030-4SK 3.0 BML049-4PK *BML049-4SK 4.9 BML061-4PK *BML061-4SK 6.1 BML076-4PK *BML076-4SK 7.6 BML098-4PK *BML098-4SK 9.8 BML122-4PK *BML122-4SK 12.2 BML152-4PK *BML152-4SK 15.2 BML192-4PK *BML192-4SK 19.2 CHRLYNN "S" MODEL 103-1573 103-1570 3.6 103-1002 103-1010 4.5 103-1003 103-1011 5.9 103-1574 103-1571 7.3 103-1575 103-1572 8.9 103-1004 103-1012 9.7 103-1005 103-1013 11.3 103-1006 103-1014 14.1 103-1007 103-1015 17.9 103-1008 103-1016 22.6 DNFOSS "OMR" MODEL 151-2421 151-2341 3.1 151-2422 151-2342 4.9 151-2423 151-2343 6.1 151-2424 151-2344 7.7 151-2224 151-2421 151-2425 151-2345 9.7 151-2426 151-2346 12.2 151-2427 151-2347 15.2 151-2428 151-2348 19.3 151-2429 151-2349 22.7 PORTS SIZE STNDRD 2 BOLT/KEYED SHFT(SPLINE SHFTS VILBLE) IFP MODEL BML030-2PK *BML030-2SK 3.0 BML049-2PK *BML049-2SK 4.9 BML061-2PK *BML061-2SK 6.1 BML076-2PK *BML076-2SK 7.6 BML098-2PK *BML098-2SK 9.8 BML122-2PK *BML122-2SK 12.2 BML152-2PK *BML152-2SK 15.2 BML192-2PK *BML192-2SK 19.2 CHRLYNN "H" MODEL 103-1540 103-1537 3.6 103-1026 103-1034 4.5 103-1027 103-1035 5.9 103-1541 103-1538 7.3 103-1542 103-1539 8.9 103-1028 103-1036 9.7 103-1029 103-1037 11.3 103-1030 103-1038 14.1 103-1031 103-1039 17.9 103-1032 103-1040 22.6 DNFOSS "OMR" MODEL 151-2084 151-2001 3.1 151-2082 151-2002 4.9 151-2083 151-2003 6.1 151-2084 151-2004 7.7 151-2085 151-2005 9.7 151-2086 151-2006 12.2 151-2087 151-2007 15.2 151-2088 151-2008 19.3 151-2089 151-2009 22.7 PORTS SIZE
IFP BML HIGH TORQUE TIMING PROCEDURE STNDRD ROTTION Motor rotation will be as shown in Figure #1 when the following timing procedure is used.position tooth slot#1 on shaft assembly in line with tooth slot#3 highest point of geroter - VIEW GEROTER HIGHEST POINT TOOTH SLOT #3 TOOTH SLOT #1 C SHFT ROTOR Figure #1 When timing is orientated as shown TIMING PROCEDURE REVERSE ROTTION Motor rotation will be as shown in Figure #2 when the following timing procedure is used.position tooth slot#2 on shaft assembly in line with tooth slot#3 highest point of geroter GEROTER HIGHEST POINT - VIEW TOOTH SLOT #3 C TOOTH SLOT #2 Figure #2 SHFT ROTOR When timing is orientated as shown