-SERIES Dual Output W - 225W Features 15 Complies the standard of the harmonics current limiter Worldwide input: 85-265VAC Peak load accommodatable double power: Approximately twice the value of average output current Operating ambient temperature range (-1C to +5C: %) Output voltage adjusting trimmer Low leakage current Complies with EMI / immunity standards Safety standard approved: CE(LVD)/UL/CSA/EN A wide variety of types: input/output (connector/ terminal block), with L angle, with cover Applications Product Line up 225 Model naming method - 524 / Option 1 Blank: PCB type L: L-shape metal plate type A: With cover Option 2 (Blank: Molex connector) J: JST connector T: Terminal block (vertical) Combination of output voltages Active filter Peak current Output power Series name 2 Conformity to RoHS Directive This means that, in conformity with EU Directive 2/95/ EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications. - (Dual Output, Peak Current) Output W(Peak186W) 15W(Peak294W) 225W(Peak4W) Voltage Output Current(Peak)/Model Output Current(Peak)/Model Output Current(Peak)/Model 5V -524/J 15-524/J 24V 4A(8A) 5A(12A) 9A(18A) 225-524/J -P - - A-349
225 225 Specifications -P - MODEL 225-524 ITEMS/UNITS CH 1 2 Voltage Range (*3) V AC85-265 or DC1-37 Frequency (*3) Hz 47-63 Power Factor (/VAC)(typ) (*2).99 /.95 Input Efficiency (/VAC)(typ) (*2) % 81 / 83 Current (/VAC)(typ) (*2) A 2.81 / 1.43 Inrush Current (/VAC)(typ) (*4) A 15 / 3 at Ta=25, cold start Leakage Current (*1) ma.75 max (Low leakage current option available --> /FG. Refer to application note). Nominal Voltage VDC 5 24 Maximum Current A 5 9 Maximum Peak Current (/VAC) (*1) A - 14 / 18 Maximum Peak Power (*1) W - 336 / 432 Total Average Power W 225 Total Allowable Peak Power (/VAC) (*1) W 344 / 4 Output Voltage Setting Accuracy (*2) 4.9-5.1V 23.52-24.48V Maximum Line Regulation (*5)(*6) mv 96 Maximum Load Regulation (*5)(*7) mv 15 Temperature Coefficient.2%/ Maximum Ripple & Noise (<Ta<7 ) (*5) mvp-p 1 15 Maximum Ripple & Noise (-1<Ta< ) (*5) mvp-p 1 1 Hold-up Time (typ) (*2) ms Voltage Adjustable Range VDC 4.5-5.5 22.8-27.6 Over Current Protection (*8) > 15% > 5% Over Voltage Protection (*9) VDC 1-145 Function Remote ON/OFF Control - Possible Parallel Operation Not possible Series Operation Not possible Environment Operating Temperature (*11) -1 to + 7 Convection: -1 to +5 : '%', + : 5%, +7 : % Storage Temperature - 3 to +85 Operating Humidity %RH - 9 (No dewdrop) Storage Humidity %RH 1-95 (No dewdrop) Vibration (Non-operating) Shock (In package) Cooling Input Withstand Voltage Isolation Isolation Resistance Safety Standards PFHC Standards EMI Immunity Mechanical 1-55Hz (sweep for 1min) Less than 19.6m/s² constant, X, Y, Z 1hour each Less than 196.1m/s² Convection cooling - Output : 3.kVAC (ma), Input - FG : 2.kVAC (ma) Output - FG : 5VAC (ma) for 1min. More than MΩ at Ta=25 and 7%RH, Output - FG : 5VDC Approved by UL95-1, CSA C22.2 No.95-1, EN95-1, EN5178. Built to meet DENAN Built to meet IEC-3-2 Complies with FCC-B, CISPR22-B, EN5522-B, VCCI-B Built to meet EN-4-2,-3,-4,-5,-6,-8,-11 Weight (typ) g 67 Size (W x H x D) mm 95 x 45 x 222 (Refer to outline drawing) (*1) Operating period at peak output current (i) 9~14A: less than 1 sec; Duty.35 (ii) 14~18A: less than 5 sec; Duty.. (Average output power and current is less than maximum output power and current.) For peak load derating method, please refer to instruction manual for details. (*2) At /VAC and total average output power, Ta = 25. (*3) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as - 2VAC, 5/Hz on name plate. (*4) Not applicable for the in-rush current to noise filter for less than.2ms. (*5) Please refer to Fig A for measurement of line & load regulation and output ripple voltage. (Measure with normal probe.) (*6) 85-132VAC and 17-265VAC, constant load. (*7) No load - full load, constant input voltage. (*8) Current limiting with automatic recovery. Avoid to operate at overload or dead short for more than 3 seconds. (*9) OVP circuit will shutdown output, manual reset. (line recycle) (OVP for V1, V1 & V2 shutdown, OVP for V2, only V2 shutdown.) (*1) Measured by each measuring method of UL, CSA, EN and DENAN (at Hz). (*11) At standard mounting method, Fig B. - Load(%) is percent of maximum output load (Item 2 and 4), do not exceed derating in both maximum output current and power -For other mountings, refer to derating curve. -When forced air cooling, refer to derating curve. Recommended EMC Filter - RSEL-6W Please refer to "TDK-Lambda EMC Filters" catalog. A-358
225 Outline Drawing 225(/J:JST connector) A. THE 5-φ3.5 HOLES ARE FOR CUSTOR'S CHASSIS HOLE, ALL MUST BE SCREWED IN ORDER TO CONFORM THE VIBRATION SPEC. B. MODEL NA, INPUT VOLTAGE RANGE, AVERAGE OUTPUT POWER, C. COUNTRY OF MANUFACTURER WILL BE SHOWN HERE. D. TO KEEP A DISTANCE MORE THAN 4.5mm FROM PC-BOARD EDGE, LEAD CUT AND COMPONENT HEIGHT TO CUSTOR'S CHASSIS. RECOMNDED HOUSING AND TERMINAL PIN. PIN HEADER (OUTPUT SIDE CN2) B1P-VH JST 1 225(/JL:With L-shape metal plate, JST connector) PIN HEADER (OUTPUT SIDE CN2) B1P-VH JST 1 225(/JA:With cover, JST connector) RECOMNDED HOUSING & TERMINAL PIN : SOCKET HOUSING (CN2) VHR-1N JST 1 HAND CRIMPING TOOL: YC-1R CN1, CN2 MANUFACTURER: JST HAND CRIMPING TOOL: YC-11R OR YRS-11 CN3 MANUFACTURER: JST A. M4 EMBOSSED TAPPED & COUNTERSUNK HOLES (6) ARE FOR CUSTOR'S CHASSIS. SCREW MUST NOT PROTRUDE INTO POWER SUPPLY BY MORE THAN 6mm. B. φ4.5 HOLES (3) AND R2.25 SLOT HOLES (2) ARE FOR CUSTOR'S CHASSIS. (USE M4 SCREW) C. MODEL NA, INPUT VOLTAGE RANGE, AVERAGE OUTPUT POWER, NOMINAL OUTPUT VOLTAGE, AVERAGE OUTPUT CURRENT AND PEAK OUTPUT CURRENT ARE SHOWN HERE IN ACCORDANCE WITH THE ON/OFF, REMOVE JM-2W-96 AND REFER TO THE TABLE FOR RECOMNDED HOUSING AND TERMINAL PIN. RECOMNDED HOUSING & TERMINAL PIN : SOCKET HOUSING (CN2) VHR-1N JST 1 HAND CRIMPING TOOL: YC-1R CN1,CN2 MANUFACTURER: JST HAND CRIMPING TOOL: YC-11R OR YRS-11 CN3 MANUFACTURER: JST A. M4 EMBOSSED TAPPED & COUNTERSUNK HOLES (6) ARE FOR CUSTOR'S CHASSIS. SCREW MUST NOT PROTRUDE INTO POWER SUPPLY BY MORE THAN 6mm. B. Φ4.5 HOLES (3) AND R2.25 SLOT HOLES (2) ARE FOR CUSTOR'S CHASSIS. (USE M4 SCREW) C. MODEL NA, INPUT VOLTAGE RANGE, AVERAGE OUTPUT POWER, NOMINAL OUTPUT VOLTAGE, AVERAGE OUTPUT CURRENT AND PEAK OUTPUT CURRENT ARE SHOWN HERE IN ACCORDANCE WITH THE ON/OFF, REMOVE JM-2W-96 AND REFER TO THE TABLE FOR RECOMNDED HOUSING AND TERMINAL PIN. -P - PIN HEADER (OUTPUT SIDE CN2) B1P-VH JST 1 RECOMNDED HOUSING & TERMINAL PIN : SOCKET HOUSING (CN2) VHR-1N JST 1 HAND CRIMPING TOOL: YC-1R CN1,CN2 MANUFACTURER: JST HAND CRIMPING TOOL: YC-11R OR YRS-11 CN3 MANUFACTURER: JST A-359 -
225 Outline Drawing 225(/T:Vertical terminal) A. THE 5-φ3.5 HOLES ARE FOR CUSTOR'S CHASSIS HOLE. ALL MUST BE SCREWED IN ORDER TO CONFORM THE VIBRATION SPEC. B. TO KEEP A DISTANCE MORE THAN 4.5mm FROM PC-BOARD EDGE, LEAD CUT AND COMPONENT HEIGHT TO CUSTOR'S CHASSIS. C. FG IS FOR SAFETY GROUND CONNECTION. D. CN3 IS NORMALLY SHORTED BY JM-2W-96(JST). IF USING REMOTE RECOMNDED HOUSING AND TERMINAL PIN. -P - 225(/TL:Vertical mounting, with L-shape metal plate) 225(/TA:Vertical terminal, with cover) RECOMNDED HOUSING & TERMINAL PIN: HAND CRIMPING TOOL : YC-11R OR YRS-11 CN3 MANUFACTURER : JST A. M4 EMBOSSED TAPPED & COUNTERSUNK HOLES (6) ARE FOR CUSTOR'S CHASSIS. SCREW MUST NOT PROTRUDE INTO POWER SUPPLY BY MORE THAN 6mm. B. Φ4.5 HOLES (3) AND R2.25 SLOT HOLES (2) ARE FOR CUSTOR'S CHASSIS. (USE M4 SCREW) C. MODEL NA, INPUT VOLTAGE RANGE, AVERAGE OUTPUT POWER, RECOMNDED HOUSING AND TERMINAL PIN. RECOMNDED HOUSING & TERMINAL PIN: HAND CRIMPING TOOL : YC-11R OR YRS-11 CN3 MANUFACTURER : JST S A. M4 EMBOSSED TAPPED & COUNTERSUNK HOLES (6) ARE FOR CUSTOR'S CHASSIS. SCREW MUST NOT PROTRUDE INTO POWER SUPPLY BY MORE THAN 6mm. B. Φ4.5 HOLES (3) AND R2.25 SLOT HOLES (2) ARE FOR CUSTOR'S CHASSIS. (USE M4 SCREW) C. MODEL NA, INPUT VOLTAGE RANGE, AVERAGE OUTPUT POWER, RECOMNDED HOUSING AND TERMINAL PIN. - RECOMNDED HOUSING & TERMINAL PIN: HAND CRIMPING TOOL : YC-11R OR YRS-11 CN3 MANUFACTURER : JST A-3
225 Output Derating 225 Recommended standard mounting method is (A). (B), (C), (D) and (E) are also possible. Mounting (F), (G), (H) and (I) are prohibited. Please do not use (F), where the PCB will be on the top side and heat will be trapped inside the unit. In the following derating curve, average load (%) is percent of maximum output load (both maximum output current and maximum output power in specification.) Do not exceed the load derating. PCB type (A) STANDARD (B) L-shape metal with cover (C) (D) (E) (F)Prohibited (A) STANDARD (B), (D) (C), (E) -1 1 3 5 7 (A) (A) (B), (D) (C), (E) (B) (C) CONVECTION COOLING (PCB type and with chassis type) CONVECTION COOLING (With chassis and cover type) (D) (E) (F)Prohibited (G)Prohibited (H)Prohibited ( I )Prohibited FORCED AIR COOLING (PCB type and with chassis type) (A), (B), (C), (D), (E) -1 1 3 5 7 FORCED AIR COOLING (With chassis and cover type) (A), (B), (C), (D), (E) -P - -1 1 3 5-1 1 3 5 Recommended minimum air velocity:.7m/s (Measured at component side of PCB, air must flow through component side.) - A-361