Nightscape High performance floodlights and spotlights for discharge lamps Nightscape is a range of floodlights and spotlights which offers new possibilities for the architectural illumination of buildings. Wide, medium and narrow beam axially symmetrical and rotationally symmetrical reflectors are available for all wattages. The high IP rating makes them suitable for exterior use and for applications in buildings where dust is a problem. Concept: Roland Jéol Design: Roy Fleetwood Both sizes of housing take double ended discharge lamps. Concentrating on this type of lamp made it possible to design luminares with a very shallow cross section. When installed horizontally on a facade, the luminaires only have a minimal effect on the overall appearance of the building. 14 Nightscape
The range of accessories for the Nightscape series includes a particularly strong wall arm. By moving a guiding bar, the direction of the arm can be adjusted 45. Once the required position has been reached, it is fixed by tightening the screw. Nightscape is the result of international cooperation between the lighting consultant Roland Jéol and the architect and industrial designer Roy Fleetwood. Impressive illumination of the new office building of Ströer Out-of-Home Media AG, Cologne. Nightscape A floodlights equipped with red colour filters make the façade stand out at night. Architecture: Fischer + Fischer, Cologne Lighting design: Mailänder Licht Design, Cologne Nightscape 15
Nightscape Nightscape A Asymmetrical, wide beam For metal halide lamps (HIT-DE), ceramic metal halide lamps (HIT-DE-CE) and high pressure sodium lamps (HST-DE) die cast aluminium housing, polyester powder coated, asymmetrical satin finish aluminium reflector, all exterior steel parts stainless steel, safety glass flush with frame, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, integral ignitor and LPF ballast, HPF available (see page 196), supplied without lamp Nightscape A, asymmetrical, wide beam C 0 180 C 270 8 911 040 000 black HIT-DE 70 W Rx7s 6.0 kg 69 85 8 911 0 000 white HIT-DE-CE 70 W 8 911 050 000 silver grey HST-DE 70 W 8 912 040 000 black HIT-DE 150 W Rx7s 6.5 kg 69 85 8 912 0 000 white 8 912 050 000 silver grey HST-DE 150 W HIT-DE-CE 70 W 6500 lm 8911040 24 m 16 m 12 m 8 m 4 m 168 lx 42 lx 19 lx 11 lx 7 lx 5 lx 2 m 4 m 6 m 8 m 12 m 3, 7 m 13500 lm 8912040 10, 14 m 17, 21 m 24 m 16 m 12 m 8 m 4 m 348 lx 87 lx 38 lx 22 lx 14 lx 10 lx 3, 7 m 10, 14 m 17, 21 m 150 450 0 2 m 4 m 6 m 8 m 12 m Asymmetrical, wide beam For metal halide lamps (HIT-DE) and ceramic metal halide lamps (HIT-DE-CE) Technical description: see above, asymmetrical, wide beam C 0 180 C 270 8 922 040 000 black HIT-DE 250 W Fc2 11.0 kg 72 88 8 922 0 000 white HIT-DE-CE 250 W 8 922 050 000 silver grey HIT-DE 250 W 20000 lm 39 m 32, 8922040 26 m 19, 13 m 6, 216 lx 54 lx 24 lx 13 lx 9 lx 6 lx 3 m 6 m 9 m 12 m m 15 18 m 6 m 12 m 18 m 24 m 36 m 150 450 0 16 Nightscape HIT-DE HIT-DE-CE HIT-DE HST-DE
Accessories for Nightscape floodlights Part number Colour Description 129 0 241 940 black Pole outrigger, for 1 luminaire, 129 0 241 9 white for poles Ø 76 89 mm 129 0 241 950 silver grey Accessories for Nightscape Accessories for Nightscape floodlights Part number Colour Description 129 0 242 940 black Pole outrigger, for 2 luminaires 129 0 242 9 white for poles Ø 76 89 mm 129 0 242 950 silver grey Nightscape 17
Nightscape C 270 C 0 180 Axially symmetrical reflectors Axially symmetrical reflectors distribute the light in 2 principal planes: Vertical (C0 180) and horizontal (C 270). The Nightscape range includes reflectors which offer narrow, medium or wide beam distribution in the vertical plane. All reflectors have wide beam distribution in the horizontal plane. Example 1: Axially symmetrical wide beam are mounted close to the facade. Axially symmetrical wide beam reflectors reach large areas of the facade and create uniform illumination. Example 2: Axially symmetrical narrow and medium beam As the distance from the facade increases, the light distribution needs to be more precisely directed. Axially symmetrical narrow or medium beam reflectors are used to achieve a sufficiently high luminous intensity. Example 3: Axially symmetrical narrow beam Horizontal features on a façade are to be uniformly illuminated. Axially symmetrical narrow beam floodlights produce linear light distribution which can be projected accurately onto a horizontal surface. Example 4: Axially symmetrical narrow beam The floodlights are mounted on a facade in order to provide uniform illumination. Axially symmetrical narrow beam reflectors produce an intensive band of light. The light shines parallel to the facade (wall washing). 18 Nightscape
Rotationally symmetrical reflectors The light distribution of rotationally symmetrical reflectors is the same in all planes. Therefore the beam angle in one plane is sufficient to describe the characteristics of a reflector. C 270 C 0 180 Nightscape Example 1: Rotationally symmetrical medium or wide beam Rotationally symmetrical medium or wide beam reflectors are suitable for the uniform illumination of symmetrical surfaces, e.g. circular or square signs. Example 2: Rotationally symmetrical medium or wide beam In situations where vertical surfaces, e.g. banners, along a facade are to be illuminated, rotationally symmetrical medium or wide beam floodlights should be used as they create a uniform light cone. The uniformity can be increased by mounting the floodlight on an arm. Example 3: Rotationally symmetrical narrow beam A facade detail is to be accentuated from a long distance. Rotationally symmetrical narrow beam spotlights are used to project light of high intensity over greater distances. Example 4: Rotationally symmetrical narrow beam The luminaires are to be mounted on a facade to provide accent lighting. Rotationally symmetrical narrow beam reflectors create intensive bands of light along the facade and thus highlight the architectural features. Nightscape 19
Nightscape A Nightscape A For compact fluorescent lamps (TC-L) die cast aluminium housing, polyester powder coated, axially symmetrical high gloss aluminium reflector, all exterior steel parts stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, integral starter and LPF ballast, supplied without lamp Nightscape A Part number* Colour Lamp Lampholder Weight Beam angle C 0 180 C 270 8 919 041 000 black 3 x TC-L 18 W 2G11 5.5 kg 107 107 8 919 061 000 white 8 919 051 000 silver grey TC-L 18 W 3750 lm 89141 16,4 m 13,7 m 10,9 m 8,2 m 5, 2,7 m 2,7 m 5, 4 m 8,1 m 10,8 m 13, 16,2 m 187 lx 47 lx 21 lx 12 lx 7 lx 5 lx 1 m 2 m 3 m 4 m 6 m 40 80 120 *Can also be supplied with electronic ballast. 20 Nightscape A TC-L
Nightscape A Axially symmetrical For metal halide lamps (HIT-DE), ceramic metal halide lamps (HIT-DE-CE) and high pressure sodium lamps (HST-DE) die cast aluminium housing, polyester powder coated, axially symmetrical aluminium reflector (high gloss or satin finish), all exterior steel parts stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, integral ignitor and LPF ballast, HPF available upon request (see page 196), supplied without lamp Nightscape A 0 0 1200 HIT-DE-CE 70 W 6500 lm 8911041 26,4 m 22,0 m 17,6 m 13,2 m 8,8 m 4,4 m 0,8 m 1, 2,3 m 3, 1 m 3,8 m 4,6 m 541 lx 135 lx lx 34 lx 22 lx 15 lx 3 m 6 m 9 m 12 m 18 m 13500 lm 8912041 44,1 m 36,7 m 29,4 m 22,0 m 14,7 m 7,3 m 1,3 m 2, 6 m 3,8 m 5, 1 m 6,4 m 7,7 m 405 lx 101 lx 45 lx 25 lx 16 lx 11 lx Nightscape A, axially symmetrical, narrow beam C 0 180 C 270 8 911 041 000 black HIT-DE 70 W Rx7s 6.0 kg 10 73 8 911 061 000 white HIT-DE-CE 70 W 8 911 051 000 silver grey HST-DE 70 W 8 912 041 000 black HIT-DE 150 W Rx7s 6.5 kg 10 73 8 912 061 000 white 8 912 051 000 silver grey HST-DE 150 W 500 750 HIT-DE-CE 70 W 6500 lm 8911042 26, 22,1 m 17,7 m 13,3 m 8,8 m 4,4 m 1,2 m 2, 3,7 m 5, 0 m 6,2 m 7, 399 lx 100 lx 44 lx 25 lx 16 lx 11 lx 3 m 6 m 9 m 12 m 18 m 13500 lm 26, 22,1 m 8912042 17,7 m 13,3 m 8,8 m 4,4 m 8 lx 207 lx 92 lx 52 lx 33 lx 23 lx 3 m 6 m 9 m 12 m 18 m 1,2 m 2, 3,7 m 5, 0 m 6,2 m 7, Nightscape A, axially symmetrical, medium wide beam C 0 180 C 270 8 911 042 000 black HIT-DE 70 W Rx7s 6.0 kg 22 73 8 911 062 000 white HIT-DE-CE 70 W 8 911 052 000 silver grey HST-DE 70 W 8 912 042 000 black HIT-DE 150 W Rx7s 6.5 kg 22 73 8 912 062 000 white 8 912 052 000 silver grey HST-DE 150 W 150 0 450 HIT-DE-CE 70 W 6500 lm 28,3 m 23,6 m 8911043 18,9 m 14,2 m 9,4 m 4,7 m 251 lx 63 lx 28 lx 16 lx 10 lx 7 lx 3 m 6 m 9 m 12 m 18 m 2,2 m 4, 3 m 13500 lm 6, 8, 6 m 10,8m 13,0 m 28,3 m 23,6 m 8912043 18,9 m 14,2 m 9,4 m 4,7 m 521 lx 1 lx 58 lx 33 lx 21 lx 14 lx 3 m 6 m 9 m 12 m 18 m 2,2 m 4, 3 m 6, 8,6 m 10,8 m 13,0 m Nightscape A, axially symmetrical, wide beam C 0 180 C 270 8 911 043 000 black HIT-DE 70 W Rx7s 6.0 kg 40 76 8 911 063 000 white HIT-DE-CE 70 W 8 911 053 000 silver grey HST-DE 70 W 8 912 043 000 black HIT-DE 150 W Rx7s 6.5 kg 40 76 8 912 063 000 white 8 912 053 000 silver grey HST-DE 150 W HIT-DE HIT-DE-CE HST-DE Nightscape A 21
Nightscape A Nightscape A Rotationally symmetrical For metal halide lamps (HIT-DE), ceramic metal halide lamps (HIT-DE-CE) and high pressure sodium lamp (HST-DE) die cast aluminium housing, polyester powder coated, rotationally symmetrical aluminium reflector (high gloss or satin finish), all exterior steel parts stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, integral ignitor and LPF ballast, HPF available upon request (see page 196), supplied without lamp Nightscape A, rotationally symmetrical, narrow beam 8 916 041 000 black HIT-DE 70 W Rx7s 6.0 kg 9 8 916 061 000 white HIT-DE-CE 70 W 8 916 051 000 silver grey HST-DE 70 W 8 917 041 000 black HIT-DE 150 W Rx7s 6.5 kg 9 8 917 061 000 white 8 917 051 000 silver grey HST-DE 150 W HIT-DE-CE 70 W 6500 lm 89141 Ø 1, Ø 3,1 m 482 lx 121 lx 13500 lm 8917041 Ø 4,6 m 54 lx Ø 9,2 m Ø 6,2 m lx Ø 12,3 m Ø 7,7 m 19 lx Ø 15,4 m 5000 7500 Ø 6,2 m Ø 3,1 m 250 lx 63 lx 28 lx 16 lx 10 lx m 80 m 100 m Nightscape A, rotationally symmetrical, medium wide beam 8 916 042 000 black HIT-DE 70 W Rx7s 6.0 kg 20 8 916 062 000 white HIT-DE-CE 70 W 8 916 052 000 silver grey HST-DE 70 W 8 917 042 000 black HIT-DE 150 W Rx7s 6.5 kg 20 8 917 062 000 white 8 917 052 000 silver grey HST-DE 150 W HIT-DE-CE 70 W 6500 lm 89142 Ø 1,8 m Ø 3,6 m 554 lx 139 lx 13500 lm 8917042 Ø 5,4 m 62 lx Ø 10,8 m Ø 7,2 m 35 lx Ø 14,4 m Ø 9 m 22 lx Ø 18 m 2000 00 Ø 7,2 m Ø 3,6 m 288 lx 72 lx 32 lx 18 lx 12 lx Nightscape A, rotationally symmetrical, wide beam 8 916 043 000 black HIT-DE 70 W Rx7s 6.0 kg 45 8 916 063 000 white HIT-DE-CE 70 W 8 916 053 000 silver grey HST-DE 70 W 8 917 043 000 black HIT-DE 150 W Rx7s 6.5 kg 45 8 917 063 000 white 8 917 053 000 silver grey HST-DE 150 W HIT-DE-CE 70 W 6500 lm 89143 Ø 2, Ø 399 lx 100 lx 3 m 6 m 13500 lm 8917043 Ø 7, 44 lx 9 m Ø 12,4 m Ø 9,9 m 25 lx 12 m Ø 16,6 m Ø 12,4 m 16 lx Ø 20,7 m 200 400 0 Ø 8,3 m Ø 4,1 m 299 lx 75 lx 33 lx 19 lx 12 lx 22 Nightscape A HIT-DE HIT-DE-CE HST-DE
For compact fluorescent lamps (TC-L) die cast aluminium housing, polyester powder coated, axially symmetrical high gloss aluminium reflector, all exterior steel parts stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range120, M20 cable gland, possibility for through wiring, integral starter and LPF ballast, HPF available upon request (see page 196), supplied without lamp TC-L 18 W 5000 lm 89242 18,8 m 15,7 m 12,6 m 9,4 m 6,3 m 3,1 m 2,9 m 5, 7 m 8,6 m 11,4 m 14,3 m 17,1 m 186 lx 46 lx 21 lx 12 lx 7 lx 5 lx 1 m 2 m 3 m 4 m 6 m Part number* Colour Lamp Lampholder Weight Beam angle C 0 180 C 270 8 929 042 000 black 4 x TC-L 18 W 2G11 9.0 kg 110 115 8 929 062 000 white 8 929 052 000 silver grey *Can also be supplied with electronic ballast. The screws used to close the fitting are integrated into the hinges. Depending on the installation, the frame can be opened to either side to gain access to the inside of the luminaire. TC-L 23
, 250 W Axially symmetrical For metal halide lamps (HIT-DE) and high pressure sodium lamps (HST-DE) die cast aluminium housing, polyester powder coated, axially symmetrical aluminium reflector (high gloss or satin finish), all exterior steel parts stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, integral ignitor and LPF ballast, HPF available upon request (see page 196), supplied without lamp, axially symmetrical, narrow beam C 0 180 C 270 8 922 041 000 black HIT-DE 250 W Fc2 11.0 kg 13 72 8 922 061 000 white 8 922 051 000 silver grey 8 922 046 000 black HST-DE 250 W Fc2 11.0 kg 13 72 8 922 066 000 white 8 922 056 000 silver grey HIT-DE 250 W 20000 lm 8922041 43,9 m 36,6 m 29,3 m 22,0 m 14,6 m 7,3 m 1,3 m 2, 3,8 m 5, 1 m 6,3 m 7,6 m 541 lx 135 lx lx 34 lx 22 lx 15 lx HST-DE 250 W 25500 lm 8922046 43,9 m 36,6 m 29,3 m 22,0 m 14,6 m 7,3 m 6 lx 1,3 m 2, 173 lx 3,8 m 77 lx 5, 1 m 43 lx 6,3 m 28 lx 7,6 m 19 lx 500 750 1000, axially symmetrical, medium wide beam C 0 180 C 270 8 922 042 000 black HIT-DE 250 W Fc2 11.0 kg 28 71 8 922 062 000 white 8 922 052 000 silver grey 8 922 047 000 black HST-DE 250 W Fc2 11.0 kg 24 73 8 922 067 000 white 8 922 057 000 silver grey HIT-DE 250W 20000 lm 8922042 42, 35,4 m 28,3 m 21,2 m 14,2 m 7,1 m 2, 5, 0 m 7, 10,0 m 12,6m 15,1 m 407 lx 102 lx 45 lx 25 lx 16 lx 11 lx HST-DE 250 W 25500 lm 44,2 m 36,9 m 8922047 29, 22,1 m 14,7 m 7,4 m 564 lx 141 lx 63 lx 35 lx 23 lx 16 lx 2,1 m 4, 1 m 6,2 m 8, 3 m 10,4m 12,4 m 500 750, axially symmetrical, wide beam C 0 180 C 270 8 922 043 000 black HIT-DE 250 W Fc2 11.0 kg 48 70 8 922 063 000 white 8 922 053 000 silver grey 8 922 048 000 black HST-DE 250 W Fc2 11.0 kg 49 70 8 922 068 000 white 8 922 058 000 silver grey HIT-DE 250W 20000 lm 25,3 m 21,1 m 8922043 16,9 m 12,7 m 8,4 m 4,2 m 721 lx 180 lx 80 lx 45 lx 29 lx 20 lx 3 m 6 m 9 m 12 m 18 m 2,7 m HST-DE 250 W 25500 lm 2,7 m 5, 4 m 5, 4 m 8,2 m 8,2 m 10,9 m 13,6m 16,3 m 25,3 m 21,1 m 8922048 16,9 m 12,7 m 8,4 m 4,2 m 919 lx 2 lx 102 lx 57 lx 37 lx 26 lx 10,9 m 13,6 m 16,3 m 150 0 450 3 m 6 m 9 m 12 m 18 m 24 HIT-DE HST-DE
, 250 W Rotationally symmetrical For metal halide lamps (HIT-DE) and high pressure sodium lamps (HST-DE) die cast aluminium housing, polyester powder coated, rotationally symmetrical aluminium reflector (high gloss or satin finish), all exterior steel parts stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, integral ignitor and LPF ballast, HPF available upon request (see page 196), supplied without lamp 00 4500 HIT-DE 250 W 20000 lm 8927041 Ø 3,4 m 258 lx HST-DE 250 W 25500 lm 8927046 Ø 6,7 m 64 lx Ø 10,1 m 29 lx m Ø 10,1 m Ø 13,4 m 16 lx 80 m Ø 13,4 m Ø 16,8 m 10 lx 100 m Ø 16,8 m, rotationally symmetrical, narrow beam 8 927 041 000 black HIT-DE 250 W Fc2 11.0 kg 10 8 927 061 000 white 8 927 051 000 silver grey 8 927 046 000 black HST-DE 250 W Fc2 11.0 kg 10 8 927 066 000 white 8 927 056 000 silver grey Ø 6,7 m Ø 3,4 m 328 lx 82 lx 36 lx 21 lx 13 lx m 80 m 100 m 1000 1500 HIT-DE 250 W 20000 lm 8927042 Ø 3,7 m 318 lx HST-DE 250 W 25500 lm Ø 7, 79 lx Ø 11,2 m 35 lx Ø 20 lx Ø 19,8 m Ø 18,7 m 13 lx Ø 24,7 m, rotationally symmetrical, medium wide beam 8 927 042 000 black HIT-DE 250 W Fc2 11.0 kg 21 8 927 062 000 white 8 927 052 000 silver grey 8 927 047 000 black HST-DE 250 W Fc2 11.0 kg 28 8 927 067 000 white 8 927 057 000 silver grey 8927047 Ø 14,8 m Ø 9,9 m Ø 4,9 m 281 lx 70 lx 31 lx 18 lx 11 lx 500 750 1000 HIT-DE 250 W 20000 lm 8927043 Ø 3,2 m Ø 6,3 m 687 lx 172 lx HST-DE 250 W 25500 lm Ø 9, 76 lx Ø 12,7 m 43 lx Ø 15,8 m Ø 15,9 m 27 lx Ø 19,7 m, rotationally symmetrical, wide beam 8 927 043 000 black HIT-DE 250 W Fc2 11.0 kg 35 8 927 063 000 white 8 927 053 000 silver grey 8 927 048 000 black HST-DE 250 W Fc2 11.0 kg 43 8 927 068 000 white 8 927 058 000 silver grey 8927048 Ø 11,8 m Ø 7,9 m Ø 3,9 m 1 lx 150 lx 67 lx 38 lx 24 lx HIT-DE HST-DE 25
, 400 W Axially symmetrical For metal halide lamps (HIT-DE) and high pressure sodium lamps (HST-DE) die cast aluminium housing, polyester powder coated, axially symmetrical aluminium reflector (high gloss or satin finish), all exterior steel parts are stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, separate ballast required, integral ignitor, LPF and HPF ballasts available (see page 196), supplied without lamp, axially symmetrical, narrow beam C 0 180 C 270 8 923 041 000 black HIT-DE 400 W Fc2 7.5 kg 13 72 8 923 061 000 white 8 923 051 000 silver grey 8 923 046 000 black HST-DE 400 W Fc2 7.5 kg 13 72 8 923 066 000 white 8 923 056 000 silver grey HIT-DE 400 W 0 lm 89241 14,6 m 7,3 m 1,3 m 22,0 m 2, 29,3 m 3,8 m 36,6 m 5, 1 m 43,9 m 6,3 m 7,6 m 974 lx 244 lx 108 lx 61 lx 39 lx 27 lx HST-DE 400 W 48000 lm 89246 29,3 m 14,6 m 325 lx 2, 43,9 m 5, 1 m 81 lx 58,6 m 7,6 m 36 lx 73,2 m 10,1 m 20 lx 87,8 m 12,6m 13 lx 15,2 m 9 lx 500 750 1000 m, axially symmetrical, medium wide beam C 0 180 C 270 8 923 042 000 black HIT-DE 400 W Fc2 7.5 kg 25 71 8 923 062 000 white 8 923 052 000 silver grey 8 923 047 000 black HST-DE 400 W Fc2 7.5 kg 23 73 8 923 067 000 white 8 923 057 000 silver grey HIT-DE 400 W 0 lm 89242 7,1 m 826 lx 14,2 m 2,2 m HST-DE 400 W 48000 lm 89247 14,7 m 266 lx 21,2 m 4, 4 m 207 lx 29, 4,1 m 44,2 m 8, 3 m 66 lx 28,3 m 6, 92 lx 59,0 m 12,4 m lx 35,4 m 8, 7 m 52 lx 42, 73,7 m 16,6 m 17 lx 10,9m 33 lx 88, 20,7m 11 lx 13,1 m 23 lx 24,9 m 7 lx 400 0 m, axially symmetrical, wide beam C 0 180 C 270 8 923 043 000 black HIT-DE 400 W Fc2 7.5 kg 45 71 8 923 063 000 white 8 923 053 000 silver grey 8 923 048 000 black HST-DE 400 W Fc2 7.5 kg 48 70 8 923 068 000 white 8 923 058 000 silver grey HIT-DE 400 W 0 lm 89243 7,1 m 504 lx 14,1 m 4,3 m HST-DE 400 W 48000 lm 89248 7,0 m 623 lx 21,2 m 8, 6 m 126 lx 14,1 m 4, 21,1 m 9, 1 m 156 lx 28,2 m 12,9 m 56 lx 28,1 m 13,6 m 69 lx 35,3 m 17,1 m 32 lx 42,3 m 35,1 m 18,1 m 39 lx 21,4 m 20 lx 42,2 m 22,7 m 25 lx 25,7 m 14 lx 27,2 m 17 lx 150 0 450 26 HIT-DE HST-DE
, 400 W Rotationally symmetrical For metal halide lamps (HIT-DE) and high pressure sodium lamps (HST-DE) die cast aluminium housing, polyester powder coated, axially symmetrical aluminium reflector (high gloss or satin finish), all exterior steel parts are stainless steel, tempered safety glass, silicon gasket, closure with 4 stainless steel screws, hinged frame, mounting bracket powder coated aluminium with tilt scale: 6 drilled holes Ø 8.m, spacing 70 mm (1m, 200 mm), 1 centre hole Ø 22 mm, tilt range 120, M20 cable gland, possibility for through wiring, separate ballast required, integral ignitor, LPF and HPF ballasts available (see page 196), supplied without lamp 5000 7500 10000 HIT-DE 400 W 0 lm 8928041 Ø 2,7 m Ø 5,3 m 780 lx 195 lx HST-DE 400 W 48000 lm 8928046 Ø 8 m 87 lx m Ø 9 m Ø 10,6 m 49 lx 80 m Ø 12 m Ø 13,3 m 31 lx 100 m Ø, rotationally symmetrical, narrow beam 8 928 041 000 black HIT-DE 400 W Fc2 7.5 kg 8 8 928 061 000 white 8 928 051 000 silver grey 8 928 046 000 black HST-DE 400 W Fc2 7.5 kg 9 8 928 066 000 white 8 928 056 000 silver grey Ø 6 m Ø 3 m 1 lx 75 lx 33 lx 19 lx 12 lx m 80 m 100 m 1000 1500 2000 HIT-DE 400 W 0 lm 8928042 Ø 3,7 m Ø 7, 572 lx 143 lx HST-DE 400 W 48000 lm Ø 11,2 m 64 lx Ø 36 lx Ø 19,8 m Ø 18,7 m 23 lx Ø 24,7 m, rotationally symmetrical, medium wide beam 8 928 042 000 black HIT-DE 400 W Fc2 7.5 kg 21 8 928 062 000 white 8 928 052 000 silver grey 8 928 047 000 black HST-DE 400 W Fc2 7.5 kg 28 8 928 067 000 white 8 928 057 000 silver grey 8928047 Ø 14,8 m Ø 9,9 m Ø 4,9 m 5 lx 132 lx 59 lx 33 lx 21 lx 500 750 1000 HIT-DE 400 W 0 lm 8928043 Ø 6,3 m 9 lx HST-DE 400 W 48000 lm Ø 12,7 m 77 lx Ø 19 m 34 lx Ø 25,4 m 19 lx Ø 31, Ø 31,7 m 12 lx Ø 39,4 m, rotationally symmetrical, wide beam 8 928 043 000 black HIT-DE 400 W Fc2 7.5 kg 35 8 928 063 000 white 8 928 053 000 silver grey 8 928 048 000 black HST-DE 400 W Fc2 7.5 kg 43 8 928 068 000 white 8 928 058 000 silver grey 8928048 Ø 23,6 m Ø 15,8 m Ø 7,9 m 283 lx 71 lx 31 lx 18 lx 11 lx HIT-DE HST-DE 27
Accessories Nightscape Accessories Nightscape A/B Part number Colour Description 129 0 047 940 black Wall arm, 0 mm 129 0 047 9 white adjustable aluminium profile 129 0 047 950 silver grey with 1 sliding suspension rod Nightscape A/B Part number Colour Description 129 0 157 940 black Wall arm, 18m 129 0 157 9 white adjustable aluminium profile 129 0 157 950 silver grey with 2 sliding suspension rods Design: Roy Fleetwood Accessories Nightscape A/B Part number Colour Description 119 0 031 940 black Single pole mount arm, 119 0 031 9 white aluminium, 119 0 031 950 silver grey for pole Ø 76 89 mm Accessories Nightscape A/B Part number Colour Description 119 0 032 940 black Double pole mount arm, 119 0 032 9 white aluminium, 119 0 032 950 silver grey for pole Ø 76 89 mm Accessories Nightscape A/B Part number Colour Description 122 0 140 940 black Pole top fitter, aluminium, polyester powder 122 0 140 9 white coated, for pole Ø 76 mm with M20 thread, 122 0 140 950 silver grey for mounting one floodlight 122 0 150 940 black Pole top fitter, aluminium, polyester powder 122 0 150 9 white coated, for pole Ø 89 mm with M20 thread, 122 0 150 950 silver grey for mounting one floodlight Accessories, 400 W Part number Colour Power factor Description 119 0 041 000 black LPF Remote ballast unit 119 0 061 000 white LPF for HIT-DE/HST-DE 400 W 119 0 051 000 silver grey LPF IP65 119 0 941 000 black HPF 119 0 961 000 white HPF 119 0 951 000 silver grey HPF 28 Nightscape
Accessories Nightscape A Part number Part number Colour Description 129 0 016 940 129 0 036 940 black Cowl 129 0 016 9 129 0 036 9 white c/w frame 129 0 016 950 129 0 036 950 silver grey Nightscape A Part number Part number Colour Description 129 0 012 940 129 0 032 940 black Protection grill 129 0 012 9 129 0 032 9 white c/w frame 129 0 012 950 129 0 032 950 silver grey Accessories Nightscape Nightscape A Part number Part number Colour Description 129 0 014 940 129 0 034 940 black Vertical louvre 129 0 014 9 129 0 034 9 white c/w frame 129 0 014 950 129 0 034 950 silver grey 129 0 015 940 129 0 035 940 black Horizontal louvre 129 0 015 9 129 0 035 9 white c/w frame 129 0 015 950 129 0 035 950 silver grey Nightscape A Part number Part number Colour Description 129 0 067 940 129 0 087 940 black Radial louvre 129 0 067 9 129 0 087 9 white c/w frame 129 0 067 950 129 0 087 950 silver grey Nightscape A Part number Part number Colour Description 129 0 018 940 129 0 038 940 black Green colour filter 129 0 018 9 129 0 038 9 white c/w frame 129 0 018 950 129 0 038 950 silver grey 129 0 013 940 129 0 033 940 black Blue colour filter 129 0 013 9 129 0 033 9 white c/w frame 129 0 013 950 129 0 033 950 silver grey 129 0 017 940 129 0 037 940 black Red colour filter 129 0 017 9 129 0 037 9 white c/w frame 129 0 017 950 129 0 037 950 silver grey 129 0 011 940 129 0 031 940 black Yellow colour filter 129 0 011 9 129 0 031 9 white c/w frame 129 0 011 950 129 0 031 950 silver grey For use on spotlights with rotationally symmetrical narrow beam reflectors only 129 0 019 940 129 0 039 940 black Ribbed glass 129 0 019 9 129 0 039 9 white for vertical beam 129 0 019 950 129 0 039 950 silver grey c/w frame 129 0 020 940 129 0 040 940 black Ribbed glass 129 0 020 9 129 0 040 9 white for horizontal beam 129 0 020 950 129 0 040 950 silver grey c/w frame The frames can carry a special glass plus another accessory. They can therefore also be ordered individually. Accessories such as louvres and special glasses are fitted into a supporting frame which is screwed onto the front of the floodlight. A special glass plus another accessory can be fitted into one frame. Nightscape A Part number Part number Colour Description 129 0 051 910 129 0 071 910 yellow Filter 129 0 051 9 129 0 071 9 blue 129 0 051 970 129 0 071 970 red 129 0 051 980 129 0 071 980 green For use on spotlights with rotationally symmetrical narrow beam reflectors only 129 0 059 000 129 0 079 000 Ribbed glass for vertical beam 129 0 0 000 129 0 080 000 Ribbed glass for horizontal beam Nightscape 29