Table of Contents Part Number Index Parts Manual 3N-3010 & 3N-3020 3-S No-Till Drill Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! 21529 Cover illustration may show optional equipment not supplied with standard unit. Copyright 2018 Printed 09/24/18 196-366P
Table of Contents Table of Contents Part Number Index Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Tongue...6 Hitch To Tongue...6 Transport Latch...8 Tongue To Center Frame...10 Rockshaft And Gauge Wheel...12 Rockshaft...12 Rockshaft To Frame...14 Gauge Wheels...16 Box And Box Frames...18 Wing To Center...18 Box To Center Frame...20 Box To Wing Frames...22 Box Components...24 LED Lights (S/N 1045UU+)...26 Walkboards And Steps...28 Metering System...30 Feeder Cup Tray (7.5" LH)...30 Feeder Cup Tray (7.5" RH)...32 Feeder Cup Tray (10" LH)...34 Feeder Cup Tray (10" RH)...36 Loup Shaft Monitor (2 Channel 116-282A) (3 Channel 116-283A)...38 Seed Rate Adjustment Handle Assembly...40 Drive...42 Contact Drive Wheel...42 Transmission Drive...46 Wing Drive...48 Ratchet Clutch CW (RH Side) (196-265S)...50 Ratchet Clutch CCW (LH Side) (196-266S)...52 Openers...54 10 Series Opener Arms & Mounts...54 10 Series Opener Body...56 20 Series Opener Arms & Mounts...58 20 Series Opener Body...60 Keeton Seed Firmer (Option)...62 Air Design Scraper (Option)...64 Side Wheel Scraper (Option)...66 10 & 20 Series Seed-Lok (Option)...68 Coulters...70 Grease Bank...72 Coulter Tine (Option)...74 Press Wheels...76 2" x 13" Single Press Wheel...76 3" x 13" Single Press Wheel...78 1" x 12" Double "V" Press Wheel...80 1 1/4" x 13 1/2" Double Press Wheel...82 2" x 12 1/2" Double Press Wheel (Part 1)...84 1" x 12" Double "V" Press Wheel Short...86 1" x 12" Double "V" Press Wheel Long...88 1" x 10" Double "V" Press Wheel...90 1 1/4" x 13" Double Press Wheel...92 2" x 12 1/2" Double Press Wheel (Part 2)...94 Hydraulics...96 Hydraulics...96 Depth Stop...98 Stroke Control Valve (810-445C)...100 Hydraulic Cylinder (810-475C)...102 Hydraulic Cylinder (810-218C) (S/N 1021UU-)...104 Hydraulic Cylinder (810-221C) (S/N 1022UU+)...106 Hydraulic Cylinder (810-287C) (S/N 1021UU-)...108 Hydraulic Cylinder (810-637C) (S/N 1022UU+)...110 Point Row...112 Point Row Clutch...112 Point Row Clutch Harness & Switch...114 Height Switch Cam...116 Decals...118 Decal Placement...118 Options...120 Flat Fold Marker...120 Marker Disk And Bearings...122 Single Marker Hydraulics...124 Dual Marker Hydraulics...126 Marker Sequence Valve (810-197C)...128 Harrow...130 Part Number Index...132 Copyright 2018 All rights reserved Printed 09/24/18 Great Plains Manufacturing, Inc. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Great Plains Manufacturing, Incorporated Trademarks The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 196-366P - 2-09/24/18
Table of Contents Part Number Index Alphabetized Table of Contents Selected Models 1 1 1/4" x 13 1/2" Double Press Wheel...82 1 1/4" x 13" Double Press Wheel...92 1" x 10" Double "V" Press Wheel...90 1" x 12" Double "V" Press Wheel...80 1" x 12" Double "V" Press Wheel Long...88 1" x 12" Double "V" Press Wheel Short...86 10 & 20 Series Seed-Lok (Option)...68 10 Series Opener Arms & Mounts...54 10 Series Opener Body...56 2 2" x 12 1/2" Double Press Wheel (Part 1)...84 2" x 12 1/2" Double Press Wheel (Part 2)...94 2" x 13" Single Press Wheel...76 20 Series Opener Arms & Mounts...58 20 Series Opener Body...60 3 3" x 13" Single Press Wheel...78 A Air Design Scraper (Option)...64 B Box Components...24 Box To Center Frame...20 Box To Wing Frames...22 C Contact Drive Wheel...42 Coulter Tine (Option)...74 Coulters...70 D Decal Placement...118 Depth Stop...98 Dual Marker Hydraulics...126 F Feeder Cup Tray (10" LH)...34 Feeder Cup Tray (10" RH)...36 Feeder Cup Tray (7.5" LH)...30 Feeder Cup Tray (7.5" RH)...32 Flat Fold Marker...120 Hydraulic Cylinder (810-218C) (S/N 1021UU-)...104 Hydraulic Cylinder (810-221C) (S/N 1022UU+)...106 Hydraulic Cylinder (810-287C) (S/N 1021UU-)...108 Hydraulic Cylinder (810-475C)...102 Hydraulic Cylinder (810-637C) (S/N 1022UU+)...110 Hydraulics...96 K Keeton Seed Firmer (Option)...62 L LED Lights (S/N 1045UU+)...26 Loup Shaft Monitor (2 Channel 116-282A) (3 Channel 116-283A)...38 M Marker Disk And Bearings...122 Marker Sequence Valve (810-197C)...128 P Point Row Clutch...112 Point Row Clutch Harness & Switch...114 R Ratchet Clutch CCW (LH Side) (196-266S)...52 Ratchet Clutch CW (RH Side) (196-265S)...50 Rockshaft...12 Rockshaft To Frame...14 S Seed Rate Adjustment Handle Assembly...40 Side Wheel Scraper (Option)...66 Single Marker Hydraulics...124 Stroke Control Valve (810-445C)...100 T Tongue To Center Frame...10 Transmission Drive...46 Transport Latch...8 W Walkboards And Steps...28 Wing Drive...48 Wing To Center...18 G Gauge Wheels...16 Grease Bank...72 H Harrow...130 Height Switch Cam...116 Hitch To Tongue...6 09/24/18-3 - 196-366P
Table of Contents 196-366P Part Number Index -4-09/24/18
Table of Contents Part Number Index 09/24/18-5 - 196-366P
Hitch To Tongue Table of Contents Part Number Index 20019 196-366P - 6-09/24/18
Hitch To Tongue Table of Contents Part Number Index Tongue Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. dwg20019 196-217H 890-610C 802-317C 802-166C 194-070D 890-184C 170-033H 196-136H 170-034H 803-034C 804-030C 804-017C 804-015C 803-020C 802-082C 807-073C 802-138C 804-009C 196-112D 113-370D Image No. PSS 30NT TONGUE WLDMNT SQ TB JACK 10000 LB 10 STROKE HHCS 1 1/4-7X11 GR5 SPTHD HHCS 1 1/4-7X9 1/2 GR5 SPTHD SAFETY CHAIN WASHER SAFETY CHAIN 30000 LB SINGLE HITCH STRAP-LARGE CLEVIS HITCH WELDMENT SINGLE HITCH STRAP-SMALL NUT HEX 1 1/4-7 PLT WASHER LOCK 1 1/4 SPRING PLT WASHER FLAT 1/2 USS PLT WASHER LOCK SPRING 1/2 PLT NUT HEX 1/2-13 PLT HHCS 1/2-13X1 3/4 GR5 SPRING HOSE LOOP HEAVY HHCS 5/16-18X2 1/4 GR5 WASHER LOCK SPRING 5/16 PLT RPBY 196-146D 1/4 MARKER HYD HOSE GUARD 09/24/18-7 - 196-366P
Transport Latch Table of Contents Part Number Index 19699 196-366P - 8-09/24/18
Transport Latch Table of Contents Part Number Index Tongue Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. dwg19699 803-147C 803-006C 804-006C 807-078C 804-017C 802-226C 802-005C 805-027C 196-461D 196-464D 196-463D 802-041C 807-128C 196-462D 802-065C 803-025C 804-024C 803-019C 804-021C 805-022C 196-219H Image No. NUT HEX NYLOCK 1/2-13 NUT-HEX 1/4-20 PLT WASHER LOCK SPRING 1/4 PLT SPRING DIE 1OD X 1/2ID X 1 3/4 WASHER FLAT 1/2 USS PLT HHCS 1/2-13X2 3/4 GR5 HHCS 1/4-20X1 GR5 PIN ROLL 5/16 X 1 1/2 PLT LATCH ROD SUPPORT BAR LATCH RELEASE EXTENSION ROD LATCH RELEASE HANDLE HHCS 1/2-13X3 1/2 GR5 SPRING COMP.906OD X 9 X.105W TRANSPORT LATCH HHCS 3/4-10X2 1/4 GR5 NUT HEX 3/4-10 PLT NYLOCK WASHER FLAT 3/4 USS PLT NUT LOCK 1/2-13 PLT WASHER FLAT 5/8 SAE PLT PIN ROLL 3/16 X 1 PLT LATCH RELEASE BRACKET 09/24/18-9 - 196-366P
Table of Contents Tongue To Center Frame Part Number Index 19675 196-366P - 10-09/24/18
Table of Contents Part Number Index Tongue Tongue To Center Frame Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. dwg19675 802-429C 804-028C 804-027C 803-031C 196-604D 196-603D Image No. HHCS 1-8X10 GR5 PLT WASHER FLAT 1 USS PLT WASHER LOCK SPRING 1 PLT NUT HEX 1-8 PLT SHIM, TONGUE-FRAME SHORT SHIM, TONGUE-FRAME LONG 09/24/18-11 - 196-366P
Rockshaft Table of Contents Part Number Index 19684 196-366P - 12-09/24/18
Rockshaft Table of Contents Part Number Index Rockshaft And Gauge Wheel Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 32. dwg19684 196-216H 196-534D 802-069C 803-025C 804-039C 805-105C 805-120C 815-103C 890-005C 815-099C 816-019C 822-036C 815-102C 822-037C 802-182C 200-006D 822-039C 822-038C 181-064D 805-016C 803-029C P502001 196-208K 816-035C 814-104C 814-177C 803-219C 890-122C 814-208C 814-210C 814-206C 196-272K 196-273K Image No. 30NT ROCKSHAFT WELDMENT ROCKSHAFT LIFT CYLINDER LUG HHCS 3/4-10X5 GR5 NUT HEX 3/4-10 PLT NYLOCK WASHER FLAT 1 1/4 SAE PLT PIN COTTER 1/4 X 2 1/2 PLT PIN CLEVIS 1 1/4 X 3 HUB & SPINDLE ASY 8 BOLT 5790# BUSHING CYL 1 1/4 X 1 X 1 SPINDLE SGL 2.73X15.97 8-BOLT HUB SEAL BRG CONE 2.00IDX1.18WD #3780 HUB ASSY 8 BOLT 5790# PAINTED BRG CUP 3.67ODX.93WD #3720 HUB STUD 5/8-18X2 1/2 GR5 8-BOLT WHEEL HUB MACH. BRG CUP 3.00ODX.75WD #2720 BRG CONE 1.31IDX1.01WD #2790 7/8 SPINDLE WASHER, HARDENED PIN COTTER 3/16 X 1 1/4 PLT NUT HEX SLOTTED 7/8-14 PLT REPLACED BY 890-032C TITAN 12.5L-15 20 PLY 8 BOLT VALVE STEM TR415X.625X1 1/4 LG WHEEL 15 X 10 X 8 BOLT TIRE TITAN 12.5L-15 20 PLY NUT LUG 5/8-18 X 90 DEG PLT BUSHING 1 1/2 X 1 1/4 X 1 1/2 RIM 16.5X12, 8 BLT 6 PILT 8 BC VALVE STEM METAL TR-575 TUBLES TIRE SKID ST 395/55B16.5 NHS RH TIRE/RIM 395/55B16.5 SKID 8 LH TIRE/RIM 395/55B16.5 SKID 8 Option Option Option Option Option 09/24/18-13 - 196-366P
Table of Contents Rockshaft To Frame Part Number Index 20023 196-366P - 14-09/24/18
Table of Contents Part Number Index Rockshaft And Gauge Wheel Rockshaft To Frame Ref. Part No. Part Description Comments Revision 1. 2. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 11. 12. dwg20023 196-224K 810-287C 810-637C 160-201H 805-249C 805-124C 804-029C 805-017C 805-239C 805-017C 196-221H 196-177H 196-213H 805-001C Image No. PSS 30NT ROCKSHAFT AXLE ASSY CYL REP 4.75 X 12 X 1.50 ROD REPHASING CYL 4 3/4X12X2 ROD WING PIVOT PIN WELDMENT PIN ROLL 3/8 X 2 PLT PIN CLEVIS 1 X 3 11/16 GR5 PLT WASHER FLAT 1 SAE PIN COTTER 3/16 X 1 3/4 PLT PIN CLEVIS 1 X 3 5/16 HRD PLT PIN COTTER 3/16 X 1 3/4 PLT PSS 30NT CENTER FRAME WLDMT CYLINDER LOCK CHANNEL-1 1/2X12 2" TRANSPORT CYLINDER LOCK PIN 3/8 X 3 USABLE LW/PIN (S/N 1021UU-) (S/N 1022UU+) (S/N 1021UU-) (S/N 1022UU+) Formerly 805-152C 09/24/18-15 - 196-366P
Gauge Wheels Table of Contents Part Number Index 19685 196-366P - 16-09/24/18
Gauge Wheels Table of Contents Part Number Index Rockshaft And Gauge Wheel Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 32. 33. 34. 35. 36. 37. 38. 39. 39. dwg19685 196-215H 890-005C 890-011C 802-099C 803-019C 815-085C 816-011C 822-018C 822-019C 815-082C 822-020C 815-082C 822-021C 804-055C 805-246C 803-029C 200-001D 815-079C 815-077C 802-104C 814-178C 814-008C 816-035C 197-148K 800-001C 160-201H 805-249C 804-030C 803-034C 803-032C 161-107H 810-218C 810-221C 805-239C 804-029C 805-017C 814-207C 814-209C 814-210C 196-274K 196-275K Image No. PSS 30NT GWL ARM WLDMNT BUSHING CYL 1 1/4 X 1 X 1 BUSHING SPINDLE 1 1/2X1 1/4X1 HHCS 1/2-13X3 1/4 GR5 NUT LOCK 1/2-13 PLT SPINDLE SGL 1.75X10.72 SEAL 2.56X1.625X.438 CR16289 BRG CONE 1.50ID LM-29749 BRG CUP LM-29710 HUB 6 BOLT 4 5/8 PILOT W/ CUPS BRG CUP LM-67010 HUB 6 BOLT 4 5/8 PILOT W/ CUPS BRG CONE 1.25ID LM-67048 WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG NUT HEX SLOTTED 7/8-14 PLT HUB GREASE CAP HUB AND SPINDLE ASSY 6 BOLT HUB 6 BOLT 4 5/8 PILOT 3600 LB BOLT WHEEL 1/2-20X1 90-DEG TIRE TITAN 11L-15 X 8 PLY WHEEL 8 X 15 X 6 BOLT VALVE STEM TR415X.625X1 1/4 LG TITAN TIRE 11L-15 8 PLY 6 BLT GREASE ZERK STRAIGHT 1/4-28 WING PIVOT PIN WELDMENT PIN ROLL 3/8 X 2 PLT WASHER LOCK 1 1/4 SPRING PLT NUT HEX 1 1/4-7 PLT NUT HEX JAM 1 1/4-7 PLT NTA35 WING EYEBOLT WELDMENT CYL REP 4.5X12X1.5 ROD (TIE) CYL REP 4.25X12X1.5 ROD (TIE) PIN CLEVIS 1 X 3 5/16 HRD PLT WASHER FLAT 1 SAE PIN COTTER 3/16 X 1 3/4 PLT TIRE SKID ST 265/70B16.5 NHS RIM 16.5X8.25, 6 BLT 4.63 PILT VALVE STEM METAL TR-575 TUBLES RH TIRE/RIM 265/70B16.5 SKID 6 LH TIRE/RIM 265/70B16.5 SKID 6 Formerly 200-003D (S/N 1021UU-) (S/N 1022UU+) Option Option Option Option Option 09/24/18-17 - 196-366P
Wing To Center Table of Contents Part Number Index 19700 196-366P - 18-09/24/18
Wing To Center Table of Contents Part Number Index Box And Box Frames Ref. Part No. Part Description Comments Revision 1. 1. 2. 3. 4. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 28. 29. 30. 31. 31. 32. 33. 34. 35. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. dwg19700 196-222H 196-223H 804-023C 803-027C 196-225H 196-226H 800-001C 196-546D 802-594C 803-026C 196-247H 197-001D 803-079C 805-085C 802-086C 890-725C 196-573D 402-130D 805-021C 196-230H 890-666C 196-571D 804-071C 802-426C 803-032C 196-231H 805-174C 803-038C 802-293C 810-475C 810-216C 196-572D 196-221H 196-414H 196-418H 802-167C 804-075C 803-255C 196-412H 196-413H 802-022C 802-017C 804-013C 804-011C 164-038D 990-223R 990-228R 800-082C 803-014C Image No. PSS 30NT LH WING FRAME WLDMT PSS 30NT RH WING FRAME WLDMT WASHER LOCK SPRING 3/4 PLT NUT HEX 3/4-10 PLT PSS 30NT LH TOOLBAR WLDMT PSS 30NT RH TOOLBAR WLDMT GREASE ZERK STRAIGHT 1/4-28 TOOLBAR HORZ PIVOT PIN HHCS 3/4-10X5 1/2 GR5 NUT LOCK 3/4-10 PLT PIVOT PIN SUPPORT CAP WELDMENT BOX HINGE PIVOT WASHER NUT HEX SLOTTED 1 1/4-7 PIN COTTER 5/16 X 2 1/2 HHCS 3/4-10X2 3/4 GR5 BUSHING 3 X 2 1/2 X 2 CONNEX WASHER HARD 4 X 2.56 X.25 CYL PIN PIN COTTER 1/4 X 2 PLT OUTER FOLD LINK WELDMENT BUSHING 1 7/8X1 5/8X1 1/2 SPLT INNER SPACER TUBE WASHER FLAT 1 1/2 SAE PLT HHCS 1 1/4-7X3 1/2 GR5 PLT NUT HEX JAM 1 1/4-7 PLT INNER FOLD LUG WELDMENT PIN CLEVIS 1 X 4 11/16 GR 5 NUT HEX 1-8 NYLON INSERT PLT HHCS 1-8X8 1/2 GR5 CYL 4X16X2 ROD (TIE ROD) CYL 4X16X1.5 ROD (TIE ROD) VERTICAL PIVOT PIN PSS 30NT CENTER FRAME WLDMT HOSE GUIDE 30P WING LH HOSE GUIDE 30P WING RH HHCS 1/4-20X1 1/2 GR5 WASHER FLAT 1/4 USS PLT NUT HEX NYLOCK 1/4-20 HOSE GUIDE 30P CTR LH HOSE GUIDE 30P CTR RH HHCS 3/8-16X1 1/2 GR5 HHCS 3/8-16X1 GR5 WASHER LOCK SPRING 3/8 PLT WASHER FLAT 3/8 USS PLT HYD HOSE CLIP W/HOLES SPIRAL HOSE WRAP 2.00 DIA SPIRAL HOSE WRAP 1 ID PLASTIC CABLE TIE.31X21.5 6DIA 120LB NUT HEX 3/8-16 PLT Shown. Shown. S/N 1161AA+ S/N 1160AA- Shown. Shown. 2nd Rev. 1st Rev. 09/24/18-19 - 196-366P
Table of Contents Box To Center Frame Part Number Index 20329 196-366P - 20-09/24/18
Table of Contents Part Number Index Box And Box Frames Box To Center Frame Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. dwg20329 802-034C 804-015C 803-020C 890-312C 890-311C 150-138D 801-081C 802-203C 804-016C 803-169C 802-387C 118-402D 803-199C 197-154H 800-148C 800-112C 890-390C 890-313C Image No. HHCS 1/2-13X1 1/4 GR5 WASHER LOCK SPRING 1/2 PLT NUT HEX 1/2-13 PLT DUAL AG LIGHTS RH DUAL AG LIGHTS LH 12' EWNT LIGHT BRACKET SCREW HEX SELF TAP 1/4-20X3/4 HFSS 1/2-13X1 1/2 GR5 WASHER FLAT 1/2 SAE PLT NUT HEX FLG. LOCK 1/2-13 PLT. HFS 5/16-18X3/4 GR5 SEED BOX PARTITION NUT HEX FLANGE 5/16-18 PLT 30 FT PSS NT BOX WLDMT CABLE TIE MOUNT CABLE TIE.19X7.25 1.75D 50LB LIGHT HARNESS, 10' WISHBONE AG LIGHT WIRING HARNESS-28' S/N 1044UU- S/N 1044UU- S/N 1044UU- S/N 1044UU- S/N 1044UU- S/N 1044UU- S/N 1044UU- S/N 1044UU- S/N 1044UU- 09/24/18-21 - 196-366P
Table of Contents Box To Wing Frames Part Number Index 21505 196-366P - 22-09/24/18
Table of Contents Part Number Index Box And Box Frames Box To Wing Frames Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 8. 9. 10. 10. 11. 12. 13. 14. dwg21505 118-402D 803-199C 802-387C 802-203C 804-016C 803-169C 197-154H 196-222H 196-223H 119-190D 821-046C 802-004C 248-251D 817-042C 817-516C 803-293C Image No. SEED BOX PARTITION NUT HEX FLANGE 5/16-18 PLT HFS 5/16-18X3/4 GR5 HFSS 1/2-13X1 1/2 GR5 WASHER FLAT 1/2 SAE PLT NUT HEX FLG. LOCK 1/2-13 PLT. 30 FT PSS NT BOX WLDMT PSS 30NT LH WING FRAME WLDMT PSS 30NT RH WING FRAME WLDMT HANDLE RPBY 821-048C HHCS 1/4-20X3/4 GR5 MANUAL PAK MOUNTING PLATE MINI END WHEEL PRESS WHEEL MANUAL PAK 1'" W/ GASKET NUT HEX FLNG T-LOCK 1/4-20 YLW 09/24/18-23 - 196-366P
Box Components Table of Contents Part Number Index 20027 196-366P - 24-09/24/18
Table of Contents Part Number Index Box And Box Frames Box Components Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. dwg20027 197-154H 119-230H 802-425C 804-036C 119-154D 807-106C 119-153D 890-221C 800-121C 803-011C 817-086C 817-350C 801-154C 175-180S 313-186D 802-015C 803-209C 890-305C 805-067C 197-091D 800-101C 313-176D 817-202C 804-004C 803-001C 118-474H 197-089D 197-096D 804-075C 803-003C 802-411C Image No. 30 FT PSS NT BOX WLDMT LID 76 7/8 SEED HHCS 5/16-18X1 1/4 NYL WASHER FLAT 5/16 SAE PLT LID HANDLE SPRING.540 O.D.X 1 1/4 X.054W LATCH CASTING MACHINED 12-20 X 90 LB GAS SPRING BALL STUD 10MM X 5/16-18 X 1/2 NUT LOCK 5/16-18 PLT SEED LEVEL BUSHING SEED LEVEL INDICATOR SCR HEX HD SHT MET #8 X 1/2 13' EW LID HINGE ASSEMBLY LID HINGE PIVOT RHSNB 3/8-16X1 GR5 NUT FLANGE LOCK 3/8-16 PLT CABLE 3/64 X 11 5/8 W/ EYELETS PIN COTTER 1/8 X 3/4 SEED LEVEL CHAIN BRACKET RIVET POP 1/8X.265LG FLG LID HINGE BASE PLATE SEED LEVEL ARM MOUNT WASHER INTERNAL STAR #10 PLT NUT HEX 10-24 PLT SEED LEVEL ARM, 6 3/4R. TAB FOAM FLOAT FOAM FLOAT WASHER WASHER FLAT 1/4 USS PLT.00 HEX SS 1/4-20 NYLOCK RHSNB 3/8-16X2 GR5 09/24/18-25 - 196-366P
Table of Contents LED Lights (S/N 1045UU+) Part Number Index 68984 196-366P - 26-09/24/18
Table of Contents Part Number Index Box And Box Frames LED Lights (S/N 1045UU+) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. dwg68984 833-720C 891-836C 833-686C 801-018C 818-055C 833-694C 803-084C 806-268C 802-167C 296-193D 803-006C 804-006C 833-696C 296-192D 833-697C 151-454D 816-807C 802-203C 803-169C 801-081C 804-015C 803-020C Image No. WISHBONE WIRING HRNSS-SHRT LED ADHESIVE BACK CORD CLIP LIGHT HARNESS, 35' LEAD - LED SCREW RD HD 1/4-20 X 5/8 DECAL SLOW MOVING-GALV. BACKED LIGHT HRNSS ENHANCE MODULE LED NUT HEX NYLOCK 5/16-18 PLT U-BOLT 5/16-18X2 1/32X2 11/16 HHCS 1/4-20X1 1/2 GR5 3N-3010 LIGHT MODULE MNT NUT HEX 1/4-20 PLT WASHER LOCK SPRING 1/4 PLT LIGHT, RED LAMP - LED 3N-3010 REAR LIGHT BRKT LIGHT, AMBER LAMP LED.25 X 1.73 X 5.73 SPACER WASHER FLAT RUBBER 1/2 HFSS 1/2-13X1 1/2 GR5 NUT HEX FLG LOCK 1/2-13 PLT SCREW HEX SELF TAP 1/4-20X3/4 WASHER LOCK SPRING 1/2 PLT NUT HEX 1/2-13 PLT 09/24/18-27 - 196-366P
Table of Contents Walkboards And Steps Part Number Index 20028 196-366P - 28-09/24/18
Table of Contents Part Number Index Box And Box Frames Walkboards And Steps Ref. Part No. Part Description Comments Revision 1. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. dwg20028 196-595D 196-596D 196-227H 805-143C 805-127C 802-034C 803-019C 802-079C 804-012C 803-078C 802-388C 119-211D 805-032C 198-810H 803-209C 802-038C 804-015C 803-020C 151-026H 196-228H 196-252H Image No. LADDER MOUNT LH LADDER MOUNT RH WALKBOARD WING PSS 30 PIN HAIR COTTER.120 PLT PIN CLEVIS 1/2 X 1 3/4 HHCS 1/2-13X1 1/4 GR5 NUT LOCK 1/2-13 PLT HHCS 3/8-16X1 1/4 GR5 WASHER FLAT 3/8 SAE PLT NUT LOCK 3/8-16 NYLON INSERT HFS 3/8-16X1 GR5 OPENER HANDLE HOLDER PIN HAIR COTTER.148 WIRE SPRING ADJ HANDLE WELDMENT NUT FLANGE LOCK 3/8-16 PLT HHCS 1/2-13X2 1/4 GR5 WASHER LOCK SPRING 1/2 PLT NUT HEX 1/2-13 PLT STEP WELDMENT PSS 30NT LADDER RH LADDER WELDMENT 3N-30 S/N 1167AA+ Shown S/N 1167AA+ S/N 1166AA- Shown S/N 1166AA- 09/24/18-29 - 196-366P
Table of Contents Feeder Cup Tray (7.5" LH) Part Number Index 21506 196-366P - 30-09/24/18
Table of Contents Part Number Index Metering System Feeder Cup Tray (7.5" LH) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. dwg21506 109-091D 118-226S 118-340D 118-341D 118-346D 118-370D 118-376D 118-437D 118-438D 816-002C 118-443D 118-616D 118-639D 118-640D 118-641D 800-009C 801-035C 802-004C 802-014C 803-194C 804-012C 804-013C 804-031C 805-023C 817-074C 817-075C 890-190C 890-350C 118-508D 118-336D 822-103C 800-004C 800-107C 817-071C 817-069C 817-070C 817-068C 801-057C 817-004C 817-073C Image No. MACHINED ADJUSTMENT SPOOL FEEDER CUP BEARING ASSEMBLY 5 5/8 BOX DVDR FOR 7 1/2 ROW 2SNT SEED BOX DIVIDER CLIP SPACER TUBE X 4.078 4 5/8 BOX DVDR FOR 8 ROW SPACER TUBE X 3.078 BOX DVDR 5.13 X 60DEG SPACER TUBE X 3.579 RUBBER GRAIN TUBE SPACER TUBE X 1.207 BOX DVDR FOR 4.63 ROW 3N-30 7.5 LH FEEDER CUP TRAY 3N-30 FD CUP DRIVE BAR BOX DVDR 10.0 X 40 DEG CLAMP HOSE 1 5/8 NO. 26 SCREW SET 5/16-18 SKT KP X 3/8 HHCS 1/4-20X3/4 GR5 HHCS 3/8-16X3/4 GR5 NUT HEX WHIZ 1/4-20 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER RETAINING PIN ROLL 3/16X1 1/4 PLT SEED CUP SLEEVE SEED CUP ASSEMBLY PM SEED CUP SPROCKET 5/8 SHAFT LOCKING COLLAR BEARING HUB 40A15 FEEDER CUP BEARING HOUSING BRG 30IDX55OD MM SNAP RING EXT BASIC 1 3/16 SNAP RING INTERNAL 2.165 SEED CUP ADJUSTMENT HANDLE SEED CUP RIGHT HALF SEED CUP DOOR SEED CUP LEFT HALF SCR SELF TAP 8X3/8 TYPE25 BT NYLON WASHER-SPLIT SEED CUP WASHER RETAINER 09/24/18-31 - 196-366P
Table of Contents Feeder Cup Tray (7.5" RH) Part Number Index 21507 196-366P - 32-09/24/18
Table of Contents Part Number Index Metering System Feeder Cup Tray (7.5" RH) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. dwg21507 109-091D 118-226S 118-340D 118-341D 118-346D 118-370D 118-376D 118-437D 118-438D 816-002C 118-443D 118-616D 118-640D 118-641D 118-643D 800-009C 801-035C 802-004C 802-014C 803-194C 804-012C 804-013C 804-031C 805-023C 817-074C 817-075C 890-190C 890-350C 118-508D 118-336D 822-103C 800-004C 800-107C 817-071C 817-069C 817-070C 817-068C 801-057C 817-004C 817-073C Image No. MACHINED ADJUSTMENT SPOOL FEEDER CUP BEARING ASSEMBLY 5 5/8 BOX DVDR FOR 7 1/2 ROW 2SNT SEED BOX DIVIDER CLIP SPACER TUBE X 4.078 4 5/8 BOX DVDR FOR 8 ROW SPACER TUBE X 3.078 BOX DVDR 5.13 X 60DEG SPACER TUBE X 3.579 RUBBER GRAIN TUBE SPACER TUBE X 1.207 BOX DVDR FOR 4.63 ROW 3N-30 FD CUP DRIVE BAR BOX DVDR 10.0 X 40 DEG 3N-30 7.5 RH FEEDER CUP TRAY CLAMP HOSE 1 5/8 NO. 26 SCREW SET 5/16-18 SKT KP X 3/8 HHCS 1/4-20X3/4 GR5 HHCS 3/8-16X3/4 GR5 NUT HEX WHIZ 1/4-20 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER RETAINING PIN ROLL 3/16X1 1/4 PLT SEED CUP SLEEVE SEED CUP ASSEMBLY PM SEED CUP SPROCKET 5/8 SHAFT LOCKING COLLAR BEARING HUB 40A15 FEEDER CUP BEARING HOUSING BRG 30IDX55OD MM SNAP RING EXT BASIC 1 3/16 SNAP RING INTERNAL 2.165 SEED CUP ADJUSTMENT HANDLE SEED CUP RIGHT HALF SEED CUP DOOR SEED CUP LEFT HALF SCR SELF TAP 8X3/8 TYPE25 BT NYLON WASHER-SPLIT SEED CUP WASHER RETAINER 09/24/18-33 - 196-366P
Table of Contents Feeder Cup Tray (10" LH) Part Number Index 21508 196-366P - 34-09/24/18
Table of Contents Part Number Index Metering System Feeder Cup Tray (10" LH) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. dwg21508 109-091D 118-226S 118-315D 118-339D 118-341D 118-347D 118-353D 118-356D 118-372D 816-002C 118-640D 118-641D 118-644D 800-009C 801-035C 802-009C 802-014C 803-194C 804-012C 804-013C 804-031C 805-023C 817-074C 817-075C 890-190C 890-350C 118-508D 118-336D 822-103C 800-004C 800-107C 817-071C 817-069C 817-070C 817-068C 801-057C 817-004C 817-073C Image No. MACHINED ADJUSTMENT SPOOL FEEDER CUP BEARING ASSEMBLY SPACER TUBE X 4.539 4 13/16 BOX DVDR FOR 7 1/2 ROW 2SNT SEED BOX DIVIDER CLIP SPACER TUBE X 3.266 185C058TUBE X 6.578 BOX DIVIDER FOR 10 ROW BOX DVDR 6.13 X 60DEG RUBBER GRAIN TUBE 3N-30 FD CUP DRIVE BAR BOX DVDR 10.0 X 40 DEG 3N-30 10 LH FEEDER CUP TRAY CLAMP HOSE 1 5/8 NO. 26 SCREW SET 5/16-18 SKT KP X 3/8 RHSNB 5/16-18X1 1/4 GR5 HHCS 3/8-16X3/4 GR5 NUT HEX WHIZ 1/4-20 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER RETAINING PIN ROLL 3/16X1 1/4 PLT SEED CUP SLEEVE SEED CUP ASSEMBLY PM SEED CUP SPROCKET 5/8 SHAFT LOCKING COLLAR BEARING HUB 40A15 FEEDER CUP BEARING HOUSING BRG 30IDX55OD MM SNAP RING EXT BASIC 1 3/16 SNAP RING INTERNAL 2.165 SEED CUP ADJUSTMENT HANDLE SEED CUP RIGHT HALF SEED CUP DOOR SEED CUP LEFT HALF SCR SELF TAP 8X3/8 TYPE25 BT NYLON WASHER-SPLIT SEED CUP WASHER RETAINER 09/24/18-35 - 196-366P
Table of Contents Feeder Cup Tray (10" RH) Part Number Index 21509 196-366P - 36-09/24/18
Table of Contents Part Number Index Metering System Feeder Cup Tray (10" RH) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. dwg21509 109-091D 118-226S 118-315D 118-339D 118-341D 118-347D 118-353D 118-356D 118-372D 816-002C 118-640D 118-641D 118-645D 800-009C 801-035C 802-004C 802-014C 803-194C 804-012C 804-013C 804-031C 805-023C 817-074C 817-075C 890-190C 890-350C 118-508D 118-336D 822-103C 800-004C 800-107C 817-071C 817-069C 817-070C 817-068C 801-057C 817-004C 817-073C Image No. MACHINED ADJUSTMENT SPOOL FEEDER CUP BEARING ASSEMBLY SPACER TUBE X 4.539 4 13/16 BOX DVDR FOR 7 1/2 ROW 2SNT SEED BOX DIVIDER CLIP SPACER TUBE X 3.266 185C058TUBE X 6.578 BOX DIVIDER FOR 10 ROW BOX DVDR 6.13 X 60DEG RUBBER GRAIN TUBE 3N-30 FD CUP DRIVE BAR BOX DVDR 10.0 X 40 DEG 3N-30 10 RH FEEDER CUP TRAY CLAMP HOSE 1 5/8 NO. 26 SCREW SET 5/16-18 SKT KP X 3/8 HHCS 1/4-20X3/4 GR5 HHCS 3/8-16X3/4 GR5 NUT HEX WHIZ 1/4-20 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER RETAINING PIN ROLL 3/16X1 1/4 PLT SEED CUP SLEEVE SEED CUP ASSEMBLY PM SEED CUP SPROCKET 5/8 SHAFT LOCKING COLLAR BEARING HUB 40A15 FEEDER CUP BEARING HOUSING BRG 30IDX55OD MM SNAP RING EXT BASIC 1 3/16 SNAP RING INTERNAL 2.165 SEED CUP ADJUSTMENT HANDLE SEED CUP RIGHT HALF SEED CUP DOOR SEED CUP LEFT HALF SCR SELF TAP 8X3/8 TYPE25 BT NYLON WASHER-SPLIT SEED CUP WASHER RETAINER 09/24/18-37 - 196-366P
Table of Contents Part Number Index Loup Shaft Monitor (2 Channel 116-282A) (3 Channel 116-283A) 34220 196-366P - 38-09/24/18
Table of Contents Part Number Index Metering System Loup Shaft Monitor (2 Channel 116-282A) (3 Channel 116-283A) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. dwg34220 802-257C 800-052C 803-088C 770026 540017 710425 116-019D 801-199C 253100 116-020D 253017 253016 833-595C 318951 253017 833-596C 318917 Image No. HFSS 1/4-20X3/4 GR5 HOSE CLIP 5/8 I.D. NUT HEX LOCK 1/4-20 FLG CABLE TIE, NYLON MAGNET, ADHESIVE BACKED, LARGE NUT HEX JAM, PLASTIC M16 X 2 SHAFT SENSOR MOUNT SCR SELF TAP #10 X 3/4 LOUP SHAFT SENSOR 2&3 CHANNEL SMALL CUP SENSOR MOUNT LOUP 3 CHANNEL SHAFT MONITOR LOUP 2 CHANNEL SHAFT MONITOR SHAFT MONITOR EXT. 30' 6P WP HARNESS 3 SHAFT MONITOR LOUP LOUP 3 CHANNEL SHAFT MONITOR SHAFT MONITOR EXT. 25' 4P WP HARNESS 2 SHAFT MONITOR LOUP 09/24/18-39 - 196-366P
Table of Contents Part Number Index Seed Rate Adjustment Handle Assembly 68212 196-366P - 40-09/24/18
Table of Contents Part Number Index Metering System Seed Rate Adjustment Handle Assembly Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. dwg68212 118-444H 118-443H 109-025H 816-509C 819-001C 802-014C 804-013C 804-012C 804-040C 109-069D 805-016C 803-016C 804-001C 822-008C 800-003C 802-007C 804-010C 804-009C 803-008C 801-001C 804-003C 804-002C 803-035C Image No. SEED RATE ADJ WLDMNT SEED RATE ADJ HANDLE WLDMNT ADJ LOCK PLATE ASS'Y - 1 1/2 W GRIP 1/4 X 1 1/2 X 3 LG NAME PLATE ADJ. GUIDE LONG HHCS 3/8-16X3/4 GR5 WASHER LOCK SPRING 3/8 PLT WASHER FLAT 3/8 SAE PLT WASHER MACH 1.19 X.63 X 18GA ADJUSTMENT HANDLE PIVOT PIN COTTER 3/16 X 1 1/4 PLT NUT WING 1/2-13 PLT WASHER ADJ HANDLE BRG BRG BALL 17IDX40OD 6203 SNAP RING EXT 17 MM HHCS 5/16-18X3/4 GR5 WASHER FLAT 5/16 USS PLT WASHER LOCK SPRING 5/16 PLT NUT HEX 5/16-18 PLT SCREW RD HD 8-32 X 3/8 BRASS WASHER FLAT #8 BRASS WASHER INTERNAL STAR #8 BRASS NUT HEX 8-32 BRASS 09/24/18-41 - 196-366P
Table of Contents Contact Drive Wheel Part Number Index 19676 196-366P - 42-09/24/18
Table of Contents Part Number Index Drive Contact Drive Wheel Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 18. 19. 20. 20. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. dwg19676 814-134C 196-551D 804-061C 822-175C 822-195C 803-177C 802-009C 196-553D 804-015C 803-020C 196-220H 802-034C 196-556D 196-554D 805-180C 808-303C 196-555D 891-053C 891-054C 196-266S 808-319C 808-305C 808-302C 196-590D 802-469C 804-023C 803-027C 204-005S 807-055C 204-017D 803-036C 802-424C 196-600D 802-162C 808-320C 803-021C 804-019C 804-022C 136-176D 120-309D 801-035C 402-058D 402-025S 805-240C 407-073D 805-180C 196-265S 802-551C 804-075C 803-007C 196-599D 803-209C 196-271H 802-022C 802-282C Image No. TIRE/WHEEL ASSY 13/5 X 6 SPACER TUBE 1.5X1.032X1.06 WASHER MACH 1.50 X 1.00 X 18GA FLANGETTE 52 3-BOLT PLT BRG INS 7/8HEXX2.04OD SPH 803-184 FLG TP LK 5/16-18ZNYCR RHSNB 5/16-18X1 1/4 GR5 CONTACT WHEEL OUTER ARM WASHER LOCK SPRING 1/2 PLT NUT HEX 1/2-13 PLT CONTACT WHEEL BRACE WLDMT 30NT HHCS 1/2-13X1 1/4 GR5 CONTACT WHL SIDE PLATE CONTACT WHEEL SHAFT 7/8 HEX PIN ROLL 1/4 X 1 1/2 LG PLT SPKT 50C17 X 7/8 HEX BORE CTCT WHEEL SPRING ANCHOR BAR 3N-3010 / 20 ACRE METER 3N-3010 / 20 HECTARE METER RATCHET CLUTCH CCW 7/8 HEX SPKT 50C30 X 7/8 HEX BORE SPKT 50C20 X 7/8 HEX BORE SPKT 50C15 X 7/8 HEX BORE SPACER TUBE 1ODX12GAX5.5 HHCS 3/4-10X8 GR5 PLT WASHER LOCK SPRING 3/4 PLT NUT HEX 3/4-10 PLT HD DOWN PRESSURE SPRING ASSY SPRING HOLD DOWN HD COULTER SPRING PLUG CASTING NUT HEX JAM 1/2-13 PLT HHCS 1/2-13X4 FTHD ACREMETER OFFSET MOUNT PADDLE HHCS 5/8-11X3 1/2 GR5 SPKT IDLER BRG #50 15 TOOTH NUT HEX 5/8-11 PLT WASHER FLAT 5/8 USS PLT WASHER LOCK SPRING 5/8 PLT CHAIN RL #50 114 PITCHES SENSOR DISC, 42T 5.3 DIA PLTD SCREW SET 5/16-18 SKT KP X 3/8 COLLAR LOCK 7/8 HEX LOCK COLLAR, 7/8 HEX W/ SET SC PIN LINCH 3/16 X 1 9/16 LONG COUPLER, DRY FERT PIN ROLL 1/4 X 1 1/2 LG PLT RATCHET CLUTCH CW 7/8 HEX HHCS 1/4-20X2 1/4 GR5 WASHER FLAT 1/4 USS PLT NUT-LOCK 1/4-20 PLT HEX SHAFT 73.18 LONG NUT FLANGE LOCK 3/8-16 PLT SPROCKET STORAGE WLDMENT LONG HHCS 3/8-16X1 1/2 GR5 RHSNB 5/16-18X1 GR5 Refer to "Ratchet Clutch CCW (LH Side) (196-266S)". (S/N 1002UU-) Refer to "Ratchet Clutch CW (RH Side) (196-265S)". (S/N 1002UU-) (S/N 1002UU-) (S/N 1002UU-) 09/24/18-43 - 196-366P
Table of Contents Contact Drive Wheel (continued) Part Number Index Ref. 53. 54. 55. 56. 57. 58. 59. 60. 60. Part No. 198-957K 198-258D 198-259D 198-260D 800-085C 802-091C 802-095C 891-055C 891-056C Part Description AUX DOWNPRESSURE SPRING ASSY DOWNPRESS SPRING ANCHOR DOWNPRESSURE SPRING ROD DP SPRING ANCHOR SPACER TUBE SNAP RING EXT 1 HEAVY HHCS 1/2-13X1 1/2 GR5 HHCS 3/4-10X7 GR5 3N-3010 / 20 ACRE METER 3N-3010 / 20 HECTARE METER Comments (Option) Revision 196-366P - 44-09/24/18
Table of Contents Part Number Index Drive Contact Drive Wheel (continued) This Page Intentionally Left Blank 09/24/18-45 - 196-366P
Table of Contents Transmission Drive Part Number Index 21510 196-366P - 46-09/24/18
Table of Contents Part Number Index Drive Transmission Drive Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. dwg21510 120-293D 120-306D 195-157D 196-245H 196-246H 196-249S 196-269L 196-270L 196-580D 196-581D 196-584D 196-851D 402-022H 402-025S 402-242D 800-001C 800-311C 802-009C 802-022C 802-091C 802-099C 802-252C 802-282C 802-424C 802-672C 803-020C 803-177C 803-209C 804-015C 804-113C 805-067C 805-180C 805-240C 808-259C 808-302C 808-306C 808-309C 808-312C 808-314C 808-315C 808-319C 808-305C 816-107C 817-273C 817-406C 817-456C 822-175C 822-195C 805-064C 804-017C 120-305D 402-126H 804-061C 196-593D Image No. TUBE RND DOM. 1 OD X 7/32WX3.0 TUBE RND 1 OD X 7/32W X 2.13 U-JOINT PIN 3/8 U-JOINT DRIVE SHAFT YOKE TELESCOPING DRIVE SHAFT TUBE DOUBLE IDLER SPOOL ASSY #50 PNT ROW CLUTCH ASS LH NO STRAP PNT ROW CLUTCH ASS RH NO STRAP STUB SHAFT 7/8 HEX 13.94 LG SLIDER SHAFT 7/8 HEX 44.50 LG TRANS REAR SHFT 7/8 HEX 18.41L 3N-30 FD CUP IDLER PLATE CEN SPRKT STORAGE WELD LOCK COLLAR, 7/8 HEX W/ SET SC IDLER BOLT PLATE GREASE ZERK STRAIGHT 1/4-28 RPBY 800-124C RHSNB 5/16-18X1 1/4 GR5 HHCS 3/8-16X1 1/2 GR5 HHCS 1/2-13X1 1/2 GR5 HHCS 1/2-13X3 1/4 GR5 RHSNB 3/8-16X1 3/4 GR5 RHSNB 5/16-18X1 GR5 HHCS 1/2-13X4 FTHD HHCS 1/2-13X4 1/2 GR5 SPTHD NUT HEX 1/2-13 PLT 803-184 FLG TP LK 5/16-18ZNYCR NUT FLANGE LOCK 3/8-16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 USS HARD PLT PIN COTTER 1/8 X 3/4 PIN ROLL 1/4 X 1 1/2 LG PLT PIN LINCH 3/16 X 1 9/16 LONG SPKT 40B14 X 7/8 HEX BORE SPKT 50C15 X 7/8 HEX BORE SPKT 50C22 X 7/8 HEX BORE SPKT 50C25 X 7/8 HEX BORE SPKT 50C28 X 7/8 HEX BORE SPKT 50C44 X 7/8 HEX BORE SPKT 50C60 X 7/8 HEX BORE SPKT 50C30 X 7/8 HEX BORE SPKT 50C20 X 7/8 HEX BORE SEED HOSE X 45 RIBS U-JOINT NYLATRON CROSS BLOCK IDLER 1 PC 2.38X1.01X1.062 IDLER SPOOL #50 2.38X1.01X.31 FLANGETTE 52 3-BOLT PLT BRG INS 7/8HEXX2.04OD SPH PIN COTTER 7/64 X 1 LONG WASHER FLAT 1/2 USS PLT TUBE RND 1 OD X 7/32W X 1.56 OFFSET DOUBLE IDLER WELDMENT WASHER MACH 1.50 X 1.00 X 18GA POINT ROW CLUTCH SHAFT Includes items 44, 47-50 See "Point Row Clutch" See "Point Row Clutch" Can use item 36 or 39 09/24/18-47 - 196-366P
Wing Drive Table of Contents Part Number Index 21511 196-366P - 48-09/24/18
Wing Drive Table of Contents Part Number Index Drive Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. dwg21511 120-306D 120-313D 136-110D 196-245H 196-580D 196-584D 196-852D 197-194D 402-025S 802-004C 802-009C 802-091C 802-282C 802-413C 802-424C 803-006C 803-020C 803-177C 804-006C 804-007C 804-015C 804-113C 805-180C 805-240C 808-259C 808-302C 808-314C 809-038C 817-406C 817-456C 822-175C 822-195C Image No. TUBE RND 1 OD X 7/32W X 2.13 TUBE RND 1 OD X 7/32W X 3.31 CHAIN RL #40 100 PITCHES U-JOINT DRIVE SHAFT YOKE STUB SHAFT 7/8 HEX 13.94 LG TRANS REAR SHFT 7/8 HEX 18.41L 3N-30 FD CUP IDLER PLATE WNG GREASE BANK MOUNT LOCK COLLAR, 7/8 HEX W/ SET SC HHCS 1/4-20X3/4 GR5 RHSNB 5/16-18X1 1/4 GR5 HHCS 1/2-13X1 1/2 GR5 RHSNB 5/16-18X1 GR5 HHCS 1/2-13X4 1/2 GR5 HHCS 1/2-13X4 FTHD NUT-HEX 1/4-20 PLT NUT HEX 1/2-13 PLT 803-184 FLG TP LK 5/16-18ZNYCR WASHER LOCK SPRING 1/4 PLT WASHER FLAT 1/4 SAE PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 USS HARD PLT PIN ROLL 1/4 X 1 1/2 LG PLT PIN LINCH 3/16 X 1 9/16 LONG SPKT 40B14 X 7/8 HEX BORE SPKT 50C15 X 7/8 HEX BORE SPKT 50C44 X 7/8 HEX BORE CHAIN RL #50 X 80 PITCHES IDLER 1 PC 2.38X1.01X1.062 IDLER SPOOL #50 2.38X1.01X.31 FLANGETTE 52 3-BOLT PLT BRG INS 7/8HEXX2.04OD SPH 09/24/18-49 - 196-366P
Table of Contents Part Number Index Ratchet Clutch CW (RH Side) (196-265S) 19129 196-366P - 50-09/24/18
Table of Contents Part Number Index Drive Ratchet Clutch CW (RH Side) (196-265S) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. dwg19129 176-065D 176-066D 176-076D 176-078D 176-084D 196-582D 800-177C 802-004C 804-006C 805-024C 805-026C 805-180C 807-097C 808-332C 817-111C 196-265S Image No. CLUTCH FRICTION WASHER CLUTCH SPRING RETAINER CLUTCH SLIDE PLATE - CW CLUTCH DRIVE PLATE LONG - CW CLUTCH HUB 7/8 HEX BORE PIVOT SHAFT 7/8 HEX 17.38 LG SNAP RING EXT 1 1/4 HEAVY HHCS 1/4-20X3/4 GR5 WASHER LOCK SPRING 1/4 PLT PIN ROLL 3/16X 1 1/2 PLT PIN ROLL 1/4 X 3/4 PLT PIN ROLL 1/4 X 1 1/2 LG PLT SPRING COMP 2 1/16 OD X 4 LG SPKT 50A19 1.813-1.818 BR/6HOL BSHG FLG 1.26IDX1.41ODX.87L RATCHET CLUTCH CW 7/8 HEX Includes items 1-5, 7-11, 13-15 09/24/18-51 - 196-366P
Table of Contents Part Number Index Ratchet Clutch CCW (LH Side) (196-266S) 19130 196-366P - 52-09/24/18
Table of Contents Part Number Index Drive Ratchet Clutch CCW (LH Side) (196-266S) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. dwg19130 176-065D 176-066D 176-077D 176-079D 176-084D 196-582D 800-177C 802-004C 804-006C 805-024C 805-026C 805-180C 807-097C 808-332C 817-111C 196-266S Image No. CLUTCH FRICTION WASHER CLUTCH SPRING RETAINER CLUTCH SLIDE PLATE - CCW CLUTCH DRIVE PLATE LONG - CCW CLUTCH HUB 7/8 HEX BORE PIVOT SHAFT 7/8 HEX 17.38 LG SNAP RING EXT 1 1/4 HEAVY HHCS 1/4-20X3/4 GR5 WASHER LOCK SPRING 1/4 PLT PIN ROLL 3/16X 1 1/2 PLT PIN ROLL 1/4 X 3/4 PLT PIN ROLL 1/4 X 1 1/2 LG PLT SPRING COMP 2 1/16 OD X 4 LG SPKT 50A19 1.813-1.818 BR/6HOL BSHG FLG 1.26IDX1.41ODX.87L RATCHET CLUTCH CCW 7/8 HEX Includes items 1-5, 7-11, 13-15 09/24/18-53 - 196-366P
Table of Contents 10 Series Opener Arms & Mounts Part Number Index (Applies to 3N-3010 only) 20457 196-366P - 54-09/24/18
Table of Contents Part Number Index Openers 10 Series Opener Arms & Mounts (Applies to 3N-3010 only) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. dwg20457 802-419C 803-169C 198-246D 817-084C 198-619H 807-116C 198-239D 198-618H 198-614H 198-613H 806-053C 804-022C 803-021C 122-172D 802-274C 803-007C 816-037C 801-002C 196-849D Image No. HFS 1/2-13 X 5 3/4 NUT HEX FLG. LOCK 1/2-13 PLT. SING OPENER INNER PIVOT TUBE PARALLEL ARM PIVOT BUSHING SING OPENER LOWER ARM WELDMENT SPRING EXT 1 5/8OD X 6.6X.177 6 13/16 SPRING STRAP SING OPENER UPPER ARM WELDMENT PSS OPENER MOUNT REAR WLDMT PSS OPENER MOUNT FRONT WLDMT U-BOLT 5/8-11 X 7 1/32 X 6 1/2 WASHER LOCK SPRING 5/8 PLT NUT HEX 5/8-11 PLT 10P 20P UP FLOAT LIMITER HHCS 1/4-20X3 GR5 NUT-LOCK 1/4-20 PLT END WHEEL FERTILIZER HOSE SCREW HEX SLT10-16X1/2P.THD CT 3N-40 SEED HOSE CLAMP PLATE Center frame openers only 09/24/18-55 - 196-366P
Table of Contents 10 Series Opener Body Part Number Index (Applies to 3N-3010 only) 20458 196-366P - 56-09/24/18
Table of Contents Part Number Index Openers 10 Series Opener Body (Applies to 3N-3010 only) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. dwg20458 817-530C 198-616H 805-063C 805-299C 198-241D 816-302C 817-349C 107-138S 107-111D 804-040C 802-228C 805-335C 198-491H 800-213C 890-466C 188-001V 820-256C 802-079C 803-014C 804-013C 122-169D AD21010 AD21011 AD21012 AD21013 AD21014 Image No. 3N-40 SEED TUBE NO SENSOR HOLE 10 SERIES SINGULATING OPENER PIN COTTER 3/32 X 1 LONG PIN CLEVIS 1/4 X 3 23/64 USBL SEED FLAP MOUNTING CLIP, SING SEED FLAP, RUBBER, SEED-LOK SEED FLAP, UHMW, LONG DD W/205 BRG-PLD FLNG-4MM DD BRG FLANGE DUST COVER WASHER MACH 1.19 X.63 X 18GA HHCS 5/8-11X1 1/2 GR5 NYL PIN ROLL 5/16 X 5/8 PLT SCRAPER-SPREADER 10-20 SER RIVET,BUTTON HEAD 1/4 X 1/2 HSG RIBB FLG 6BOLT PLT BEARING AA205DD FLAT DISK BLADE-4MM THICK HHCS 3/8-16X1 1/4 GR5 NUT HEX 3/8-16 PLT WASHER LOCK SPRING 3/8 PLT 10P AD OUTSIDE SCRAPER MOUNT AIR DESIGN SCRAPER J.D.2.5W RH AIR DESIGN SCRAPER J.D.2.5W LH AIR DESIGN SCRAPER J.D.MNT RH AIR DESIGN SCRAPER J.D.MNT LH AIR DESIGN SCRAPER J.D.SPRING S/N 1023UU+ S/N 1022UU- 09/24/18-57 - 196-366P
Table of Contents 20 Series Opener Arms & Mounts Part Number Index (Applies to 3N-3020 only) 20459 196-366P - 58-09/24/18
Table of Contents Part Number Index Openers 20 Series Opener Arms & Mounts (Applies to 3N-3020 only) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 6. 7. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. dwg20459 802-419C 803-169C 198-246D 817-084C 198-619H 807-116C 807-076C 198-239D 198-240D 198-618H 198-614H 198-613H 198-247D 806-053C 804-022C 803-021C 122-172D 802-274C 803-007C 816-037C 801-002C 196-849D Image No. HFS 1/2-13 X 5 3/4 NUT HEX FLG. LOCK 1/2-13 PLT. SING OPENER INNER PIVOT TUBE PARALLEL ARM PIVOT BUSHING SING OPENER LOWER ARM WELDMENT SPRING EXT 1 5/8OD X 6.6X.177 SPRING EXT 1.575O.D.X.225 WIRE 6 13/16 SPRING STRAP 3 13/32 SPRING STRAP SING OPENER UPPER ARM WELDMENT PSS OPENER MOUNT REAR WLDMT PSS OPENER MOUNT FRONT WLDMT 20 SER SING FRT INNER PIVOT TB U-BOLT 5/8-11 X 7 1/32 X 6 1/2 WASHER LOCK SPRING 5/8 PLT NUT HEX 5/8-11 PLT 10P 20P UP FLOAT LIMITER HHCS 1/4-20X3 GR5 NUT-LOCK 1/4-20 PLT END WHEEL FERTILIZER HOSE SCREW HEX SLT10-16X1/2P.THD CT 3N-40 SEED HOSE CLAMP PLATE Used with 1x12 Press Wheels. Used with 1x10 Press Wheels. Used with 807-116C. Used with 807-076C. Center frame openers only 09/24/18-59 - 196-366P
Table of Contents 20 Series Opener Body Part Number Index (Applies to 3N-3020 only) 20485 196-366P - 60-09/24/18
Table of Contents Part Number Index Openers 20 Series Opener Body (Applies to 3N-3020 only) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 6. 7. 8. 9. 10. 11. 12. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. dwg20485 817-530C 198-615H 805-063C 805-296C 198-241D 816-302C 817-349C 107-133S 107-138S 804-040C 802-228C 805-335C 198-491H 812-309C 800-213C 890-466C 188-001V 820-256C 198-202D 800-118C 298-324S 812-302C 803-307C 804-014C 198-201D 817-083C 807-172C 804-012C 805-067C 198-265D 198-998S 804-022C 802-179C 198-057S 802-352C 803-043C 814-082C 814-083C 198-183D 814-081C 802-694C 122-257H 800-001C 804-195C 802-430C 802-092C 816-723C 298-001D 198-266D 198-956K 822-095C Image No. 3N-40 SEED TUBE NO SENSOR HOLE 20 SERIES SINGULATING OPENER PIN COTTER 3/32 X 1 LONG PIN CLEVIS 1/4X1 31/64 USBL SEED FLAP MOUNTING CLIP, SING SEED FLAP, RUBBER, SEED-LOK SEED FLAP, UHMW, LONG RPBY 107-135S DD W/205 BRG-PLD FLNG-4MM WASHER MACH 1.19 X.63 X 18GA HHCS 5/8-11X1 1/2 GR5 NYL PIN ROLL 5/16 X 5/8 PLT SCRAPER-SPREADER 10-20 SER SCRAPER-SPREADER 10-20SER 2003 RIVET,BUTTON HEAD 1/4 X 1/2 HSG RIBB FLG 6BOLT PLT BEARING AA205DD FLAT DISK BLADE-4MM THICK 20 SER OPNR CAM PIN SNAP RING EXT 5/8.050 T RPBY 812-328C CASTING - STAINLESS T-HANDLE NUT HEX 7/16-20 GR8 WASHER LOCK 7/16 PLT 20 SER OPNR PW CAM PRESS WHEEL ARM PIVOT BUSHING SPRING COMP 5/8 OD X 1 3/4 LG WASHER FLAT 3/8 SAE PLT PIN COTTER 1/8 X 3/4 20P SIDE DEPTH WHEEL ARM 20P ELIMINATOR BUSHING ASSY WASHER LOCK SPRING 5/8 PLT HHCS 5/8-11X2 1/2 GR5 NYL 2X13 DEPTH WHEEL ASSY HFSS 5/16-18X1/2 GR5 NUT HEX WHIZ 5/16-18 PLT 2X13 D.W. OUTER RIM HALF 2X13 SIDE DEPTH TIRE 20 SER SIDE DEPTH WL STIFF PLT 2X13 D.W. INNER RIM HALF HHCS 7/16-20 2 3/4 GR8 SEP &FERT TUBE 10-20SER 1999 GREASE ZERK STRAIGHT 1/4-28 WASHER FLAT 1.31ODX.65IDX.188T HHCS 5/8-11X2 GR5 NYL RHSNB 5/16-18X3/4 GR5 U CUP SEAL 20P DEPTH WHL OUTER BUSHING 20P DEPTH WHL ECCENTRIC BUSHNG 20 SER OPENER T-HANDLE SUBASSY BRG INS.63IDX1.57OD DBL LIP Used with Seed-Lok (shown). Used without Seed-Lok. Includes 13-16 S/N 7388B+ S/N 7387B- Includes 45-47 Includes 33-38, 44 Option Includes 20, 23-27 09/24/18-61 - 196-366P
Table of Contents Keeton Seed Firmer (Option) Part Number Index 20252 196-366P - 62-09/24/18
Table of Contents Part Number Index Openers Keeton Seed Firmer (Option) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. dwg20252 120825 129001 129BXT827 802-411C 803-014C 804-013C Image No. KEETON NARROW TAIL KEETON BRACKET 10/20 SERIES KEETON GUARD RHSNB 3/8-16X2 GR5 NUT HEX 3/8-16 PLT WASHER LOCK SPRING 3/8 PLT 09/24/18-63 - 196-366P
Table of Contents Air Design Scraper (Option) Part Number Index 20434 196-366P - 64-09/24/18
Table of Contents Part Number Index Openers Air Design Scraper (Option) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. dwg20434 122-168D 802-079C 804-013C 803-014C 890-357C Image No. 10P20P AD INSIDE SCRAPER MOUNT HHCS 3/8-16X1 1/4 GR5 WASHER LOCK SPRING 3/8 PLT NUT HEX 3/8-16 PLT SCRAPER-SPRING LOAD-AIR DESIGN 09/24/18-65 - 196-366P
Table of Contents Side Wheel Scraper (Option) Part Number Index 20185 196-366P - 66-09/24/18
Table of Contents Part Number Index Openers Side Wheel Scraper (Option) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. dwg20185 198-264D 804-009C 802-705C 802-149C 198-263D 803-209C Image No. 20P SIDE WHEEL SCRAPER MOUNT WASHER LOCK SPRING 5/16 PLT HHCS 5/16-18X5/8 RHSNB 3/8-16X3/4 GR5 20P SIDE WHEEL SCRAPER NUT FLANGE LOCK 3/8-16 PLT 09/24/18-67 - 196-366P
Table of Contents 10 & 20 Series Seed-Lok (Option) Part Number Index 20039 196-366P - 68-09/24/18
Table of Contents Part Number Index Openers 10 & 20 Series Seed-Lok (Option) Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. dwg20039 805-069C 122-166D 807-188C 805-020C 122-167D 122-165D 804-013C 803-014C 802-022C 122-250H 122-164D 807-101C 122-120D 800-093C 804-078C 801-078C 122-201S 817-134C 188-008V 801-084C 816-173C 801-141C 804-011C Image No. PIN COTTER 3/16 X 1 SEED LOCK LOCK-UP CAM SPRING COMP.85ODX2.0LGX.067W PIN COTTER 1/4 X 1 PLT 10 SER SEED LOCK LOCK-UP BAR 20 SER SEED LOCK LOCK-UP BAR WASHER LOCK SPRING 3/8 PLT NUT HEX 3/8-16 PLT HHCS 3/8-16X1 1/2 GR5 SEED LOCK MOUNT, SINGULATING SEED LOCK ARM, SINGULATING SPRING, 1 O.D.X.125WIREX 3 1/2 5 SEED-LOK WHL ARM PIVOT PIN RING SNAP EXTERNAL '"E'" 1/2 WASHER INTERNAL STAR 3/8 PLT. SCR HX SKT BUT CP 3/8-16X3/4 SD-LK 203 BEARING WHEEL ASSY 5/8 X 5 SEED FIRMING WHEEL BEARING 203 SEED-LOK WITH PIN SCR PH THD FMG #10X1/2 TP ZP RETAINER W/BONDED SEAL 4BLT LHS CP 3/8-16X3/4 GR8 PLATED WASHER FLAT 3/8 USS PLT Shown. 20 Series only. 10 Series only. 10 Series only. 09/24/18-69 - 196-366P
Coulters Table of Contents Part Number Index 20263 196-366P - 70-09/24/18
Coulters Table of Contents Part Number Index Openers Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 25. 25. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. dwg20263 249-050S 249-051H 804-156C 800-164C 802-718C 804-165C 149-559D 805-331C 149-558D 800-211C 817-513C 204-295D 802-332C 804-037C 803-049C 802-214C 816-009C 822-021C 822-020C 200-039V 200-001D 800-001C 200-002S 805-017C 820-018C 820-116C 820-082C 820-156C 804-015C 803-020C 804-055C 803-029C 806-106C 149-059D 803-021C 800-177C 149-086D 197-010D 804-022C 802-082C 803-048C Image No. CLTR CASTING ASSY CLTR SWING ARM WLMT WASHER MACH 1 1/4X3/4X14GA SNAP RING 3/4 EXTERNAL HEAVY EYE BOLT 3/4-10X14 3/4 LG SP WASHER MACH 1 7/8X1 1/4X 14GA SPRING 2.25 O.D. X.5 COIL COULTER SPRING GUIDE TUBE COULTER SPRING WASHER GREASE ADAPT 1/4-28M X 1/4 TB BUSHING 1X3/4X1 1/8 FLG HD COULTER SPRING BAR 14 3/4 BLK HHCS 7/8-9X3 GR5 WASHER LOCK SPRING 7/8 PLT NUT HEX 7/8-9 PLT RHSNB 1/2-13X1 1/4 GR5 OIL-SEAL DOUBLE LIP BEARING CONE LM-67048 BEARING CUP LM-67010 COULTER HUB & CUP ASSY HUB GREASE CAP GREASE ZERK STRAIGHT 1/4-28 COULTER HUB PACKAGE PIN COTTER 3/16 X 1 3/4 PLT COULTER BLADE FLUTED 17 COULTER BLADE 5/8 WAVY 17 COULTER BLADE 3/4 WAVY 5/8 WAVY TURBO BLADE WASHER LOCK SPRING 1/2 PLT NUT HEX 1/2-13 PLT WASHER SPINDLE - 7/8 NUT HEX SLOTTED 7/8-14 PLT U-BOLT 5/8-11 X 4 1/32 X 4 COULTER CLAMP BAR NUT HEX 5/8-11 PLT SNAP RING EXT 1 1/4 HEAVY OFFSET COULTER MOUNT PLATE OFFSET COULTER BRKT F/LH BOX WASHER LOCK SPRING 5/8 PLT HHCS 1/2-13X1 3/4 GR5 NUT HEX JAM 3/4-10 PLT Includes items 19,22 Includes items 16,17,18,20 09/24/18-71 - 196-366P
Grease Bank Table of Contents Part Number Index 20047 196-366P - 72-09/24/18
Grease Bank Table of Contents Part Number Index Openers Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. dwg20047 800-130C 800-449C 990-109R 800-211C 802-148C 804-007C 804-006C 803-006C 197-194D Image No. GREASE ZERK STRAIGHT 1/8-27NPT AD PUSH 1/4 TUBE 1/8 FNPT TUBE NYLON 1/4OD X 062WL GREASE ADAPT 1/4-28M X 1/4 TB HFSS 1/4-20X1/2 GR5 WASHER FLAT 1/4 SAE PLT WASHER LOCK SPRING 1/4 PLT NUT HEX 1/4-20 PLT GREASE BANK MOUNT 09/24/18-73 - 196-366P
Table of Contents Coulter Tine (Option) Part Number Index 19679 196-366P - 74-09/24/18
Table of Contents Part Number Index Openers Coulter Tine (Option) Ref. Part No. Part Description Comments Revision 1. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. dwg19679 802-126C 802-178C 820-114C 149-570D 802-079C 804-011C 804-013C 803-014C 196-602D 804-037C 803-049C Image No. HHCS 7/8-9X3 1/2 GR5 HHCS 7/8-9X5 1/2 GR5 2SNT COULTER TINE COULTER TINE MOUNT PLATE REAR HHCS 3/8-16X1 1/4 GR5 WASHER FLAT 3/8 USS PLT WASHER LOCK SPRING 3/8 PLT NUT HEX 3/8-16 PLT COULTER TINE OFFST MNT SPACER WASHER LOCK SPRING 7/8 PLT NUT HEX 7/8-9 PLT Use with part number 196-602D. Used with offset coulter mounts only. 09/24/18-75 - 196-366P
Table of Contents 2" x 13" Single Press Wheel Part Number Index 20040 196-366P - 76-09/24/18
Table of Contents Part Number Index Press Wheels 2" x 13" Single Press Wheel Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. dwg20040 802-058C 804-022C 803-088C 817-296C 822-170C 814-159C 802-617C 814-157C 199-042D 817-084C 198-137D 805-154C 807-106C 817-347C 802-421C 803-169C 817-328C 805-186C 122-202S Image No. HHCS 5/8-11X2 1/2 GR5 WASHER LOCK SPRING 5/8 PLT NUT HEX LOCK 1/4-20 FLG 2 X 13 PRESS WHEEL RIM HALF BRG.63ID PRESS WHL ASY 2 X 13 PRESS WHEEL TIRE HHFS 1/4-20 X 1 1/2 GR 5 2 X 13 PRESS WHEEL ASSEMBLY UNIVERSAL PW ARM MACH 2&3X13 PARALLEL ARM PIVOT BUSHING PRESS WHEEL PIVOT TUBE PIN CLEVIS 3/8 X 2 1/8 USABLE SPRING.540 O.D.X 1 1/4 X.054W OPENER TRUNION HFS 1/2-13X3 3/4 GR5 SPTHD NUT HEX FLG. LOCK 1/2-13 PLT. T-HANDLE ASSEMBLY PIN ROLL 5/32 X 5/8 PLT PW ADJUSTMENT TRUNNION ASSY Includes 12,13,14,17 & 18. 09/24/18-77 - 196-366P