C9: BMM, BMP, BMR, BMH, BMJ Series & Valves CONTENT Usage Guide 2 BMM Series Hydraulic Motors 3 BMP Series Hydraulic Motors 11 BMR Series Hydraulic Motors 24 BMH Series Hydraulic Motors 35 BMJ Series Hydraulic Motors 43 Valves for Hydraulic Motors 46 The manufacturer reserves the right to change the technical specifications without notice 1
USAGE GUIDE For optimal working, we recommend the following: 1. Oil Temperature Normal: 0 c 0 c Maximum: 90 0 c (maximum one hour) 2. Filtering & Oil Cleanliness System Filtration: µm nominal. A magnet should be installed in the filter or at the bottom of the tank to prevent ingress into the system. 3. Viscosity Based on external ambient temperature and type of application. Recommended Oil Viscosity is 32 74mm 2 /s. 4. The motors can be operated in Parallel or Series. When the pressure of the case exce eds Bar, it is recommended to install an external drain line to the tank. 5. Various output shaft and flange options are available. 5.1 Various Manifold Mount Valving available. 6. The optimal operation condition should be at the 1/3 2/3 of the rated operation. 7. In order to obtain a longer life, operating motor should operate for first hour under % of rated pressure. Motor must be filled with oil prior to being put under load. SPECIFICATION DATA OF HYDRAULIC MOTOR Distribution Type Axial Distribution Model Displacement (cm 3 /rev.) Operating Pressure (Bar) Speed Range (rpm) Output Power (kw) BMP 36-0 225 16 13 BMR 36 3 0 12 17 BMH 0-0 225-4 18.5 BMM 8-0 24 3.2 BMJ 65-3 0 842 17.9 2
BMM SERIES HYDRAULIC MOTOR BMM Series compact design providing high torque capacity from a small package giving a high power to weight ratio. Characteristic Features: Advanced manufacturing design of the Gerotor gear set, which provide hydraulic circuits, high efficiency and long life High pressure shaft seals sllow for use in both Parallel & Series circuits Advanced design giving both high power and low weight Main Specifications Type BMM 8 12 32 Geometric Displacement (cm 3 /rev.) 8.2 12.9 19.9 31.6 39.8.3 Speed (rpm) Rated. 1537 1256 814 513 452 358 19 15 00 6 0 0 24 19 12 800 6 0 Torque (Nm) Rated. 8 13 19 31 37 33 11 16 25 45 46 15 23 35 57 70 88 Peak 21 33 51 64 82 0 Output (kw) Rated. 1.3 1.7 1.7 1.7 1.7 1.2 1.8 2.4 2.4 2.4 2.2 1.8 2.6 3.2 3.2 3.2 3.2 3.2 Pressure Drop (Bar) Rated. 90 90 90 90 8.5 0 0 0 0 90 70 1 1 1 1 1 1 Peak 0 0 0 1 1 1 Flow (L/min) Rated. 14 18 18 18 16 25 25 25 25 25 Weight (kg) 1.9 2 2.1 2.2 2.3 2.4 Type BMM 8- (Bar) Inlet Pressure 1 225 Rated Speed and Rated Torque: Output value of speed and torque under rated flow and rated pressure Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute 3
PERFORMANCE DATA BMM8 [8.2cm 3 /rev.] BMM12.5 [12.9cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) 35 70 0 1 1 35 70 0 1 1 Flow (L/min) 2 4 8 3 228 3 474 3 953 5 218 5 471 5 946 8 6 7 463 7 926 156 11 426 11 884 12 111 13 391 13 855 14 58 15 331 15 816 Flow (L/min) 2 4 8 6 1 6 296 5 5 8 136 8 289 8 596 11 119 12 274 12 583 16 68 17 229 17 543 19 35 19 0 514 23 145 24 469 12 2 1444 5 1426 7 12 13 13 1324 15 1288 12 5 912 8 905 11 895 16 859 834 24 784 15 4 1912 7 1900 1861 12 1833 14 1780 15 5 1152 7 1144 11 1136 16 12 19 78 23 36 0 2432 6 2395 23 11 2328 14 2281 3 1542 7 1532 1521 15 19 1482 22 1437 25 2 19 6 1891 9 1878 14 1848 18 1828 22 1788 BMM [19.9cm 3 /rev.] BMM32 [31.6cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) 17 35 70 0 1 1 17 35 70 0 1 1 Flow (L/min) 2 4 8 3 99 4 197 4 398 9 96 9 191 9 395 14 89 14 182 13 391 19 74 19 178 19 377 26 42 26 134 27 3 21 31 112 31 319 36 74 36 288 Flow (L/min) 2 4 8 7 61 7 125 7 248 24 57 24 2 23 242 34 52 34 227 33 238 45 46 46 211 46 229 63 16 65 162 65 5 77 133 78 193 91 97 92 166 12 3 596 8 594 13 588 18 579 26 545 31 523 37 493 12 6 376 21 372 31 366 45 3 65 336 77 3 92 295 15 3 745 8 741 12 738 17 728 25 695 684 36 6 15 4 472 469 465 43 459 63 438 76 426 91 3 1 998 6 995 11 991 19 985 24 962 29 1916 35 1885 3 629 16 626 27 623 615 597 73 582 87 563 25 4 1247 9 1245 14 1242 23 1189 28 1180 33 1176 25 1 786 13 784 24 782 37 778 57 761 69 748 83 727 Cont 4
PERFORMANCE DATA BMM [39.8cm 3 /rev.] BMM [.3cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) 35 70 85 0 1 15 70 0 Flow (L/min) 2 4 8 16 45 16 96 15 197 27 27 93 26 195 36 34 37 85 36 182 44 28 44 79 44 176 51 17 52 65 52 166 62 52 63 154 Flow (L/min) 2 4 8 11 37 11 76 11 157 23 33 22 73 21 154 36 27 36 68 35 149 22 63 145 70 55 71 137 12 14 293 25 287 35 282 43 277 51 268 62 257 12 11 237 234 33 231 49 226 71 218 15 13 371 24 365 34 3 42 355 347 62 338 15 296 18 295 32 294 47 288 69 282 497 21 492 31 487 39 480 48 472 59 1463 8 395 14 395 29 393 44 390 64 381 25 7 622 19 617 29 612 37 7 44 0 56 591 25 4 498 496 25 494 490 59 484 Cont Torque (Nm) 37 Speed (rpm) 7 5
BMM END PORT DIMENSIONS & MOUNTING DATA M, U F MODEL L L1 L L1 BMM8 4 3.5 7 3.5 BMM12.5 6 5.5 9 5.5 Mounting M, U F BMM 9 8.5 112 8.5 Code 1E (Depth) 1U (Depth) 1E (Depth) 1U (Depth) BMM32 114 13.5 117 13.5 C M6 () ¼-28UNF-2B () - - - - BMM 118 17 118 17 D G3/8 (12) 9/16-18UNF (12) G3/8 (12) 9/16-18UNF (12) BMM 122 21.5 125 21.5 T G1/8 (8) 3/8-24UNF (8) G1/8 (8) 3/8-24UNF (8) 6
BMM SIDE PORT DIMENSIONS & MOUNTING DATA M, U F MODEL L L1 L L1 BMM8 5 3.5 9 3.5 BMM12.5 7 5.5 111 5.5 Mounting M, U F BMM 1 8.5 114 8.5 Code E (Depth) U (Depth) E (Depth) U (Depth) BMM32 115 13.5 119 13.5 C M6 () ¼-28UNF-2B () - - - - BMM 118 17 118 17 D G3/8 (12) 9/16-18UNF (12) G3/8 (12) 9/16-18UNF (12) BMM 123 21.5 127 21.5 T G1/8 (8) 3/8-24UNF (8) G1/8 (8) 3/8-24UNF (8) 7
SHAFT EXTENSIONS FOR BMM MOTORS 8
BMM SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE In applications without drain line, output shaft seal exceeds a bit of the pressure in the return line. When applications use the drain line, the pressure of output shaft seal equals the pressure in drain line. Bar DIRECTION OF SHAFT ROTATION STATUS OF THE SHAFT S RADIAL FORCE Fr = 61.5+L N Fr = Radial Force (N) L = Distance (mm) N = Speed (rpm) Rhomb-Flange L = 15mm Square-Flange L = mm 9
BMM SERIES HYDRAULIC MOTOR ORDER INFORMATION 1 2 3 4 Code Displacement Code Output Flange Code Shaft Code Port 8 8 12.5 12.5 16 16 32 32 M U F 3-M6 Circle-Flange, Pilot 31.5x5 3-1/4-28UNF Circle Flange, Pilot 31.5x5 2-9 Rhomb-Flange, Pilot 63x2 A B C Shaft 16, Parallel Key 5x5x16 Shaft 15.8, Parallel Key 4.8x4.8x19.35 3/8 Shaft 16.5, Involute B17x14, DIN5482 E U 1E 1U G 3/8, G 1/8 9/16-18UNF, 3/8-24UNF Rear Port G 3/8, G 1/8 Rear Port 9/16-18UNF, 3/8-24UNF
BMP SERIES HYDRAULIC MOTOR BMP series motors are medium speed, high torque motors designed on an internal gear design consisting of a rotor and stator. These motors are suitable for long operating periods at moderate pressures. Characteristic Features: Advanced manufacturing design for the Gerotor gear set, which provide high starting torque, high efficiency and long life Motors have high pressure shaft seals which can be used in Parallel or Series Smooth running over the entire speed range Main Specifications Technical data for BMP with 25 and 1 in and 1 in splined and 28.56 tapered shaft TYPE BMP, BMPH & BMPW 36 80 0 125 1 0 2 315 0 0 Geometric Displacement (cm 3 /rev.) 36 51.7 77.7 96.2 1.2 157.2 194.5 2.3 314.5 389.5 486.5 Speed (rpm) 11 770 615 490 383 3 2 192 155 1 16 14 9 770 615 4 385 3 2 190 1 Torque (Nm) 55 0 146 182 236 2 3 380 3 3 385 76 128 186 227 290 370 4 4 555 525 5 Peak 96 148 218 264 3 434 5 5 6 680 680 Output (kw) 8.0.0.0 11.0.0.0.0 8.5 7.0 6.0 5.0 11.5 12.0 12.0 13.0 12.0 12.0 12.0.5 8.5 7.0 6.0 Pressure Drop (Bar) 125 1 1 1 1 1 1 1 90 70 165 1 1 1 1 1 1 1 1 5 90 Peak 225 225 225 225 225 225 225 180 1 1 1 Flow (L/min) 55 Weight (kg) 5.6 5.6 5.7 5.9 6.0 6.2 6.4 6.7 6.9 7.4 8 Technical data for BMP with 31. and 32 shaft TYPE BMP, BMPH & BMPW 36 80 0 125 1 0 2 315 0 0 Geometric Displacement (cm 3 /rev.) 36 51.7 77.7 96.2 1.2 157.2 194.5 2.3 314.5 389.5 486.5 Speed (rpm) 11 770 615 490 383 3 2 192 155 1 16 14 9 770 615 4 385 3 2 190 1 Torque (Nm) 55 0 146 182 236 2 3 4 4 490 4 76 128 186 227 290 370 4 570 555 580 5 Peak 96 148 218 264 3 434 5 670 8 8 780 Output (kw) 8.0.0.0 11.0.0.0.0 8.5 7.0 6.0 6.0 11.5 12.0 12.0 13.0 12.0 12.0 12.0.5 8.5 7.0 7.0 Pressure Drop (Bar) 125 1 1 1 1 1 1 1 1 95 70 165 1 1 1 1 1 1 1 1 115 90 Peak 225 225 225 225 225 225 225 225 225 180 1 Flow (L/min) 55 Weight (kg) 5.6 5.6 5.7 5.9 6.0 6.2 6.4 6.7 6.9 7.4 8.0 Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute 11
PERFORMANCE DATA BMP36 [36cm 3 /rev.] BMP [51.7cm 3 /rev.] Pressure (Bar) Pressure (Bar) 70 80 0 1 125 165 80 0 125 1 1 1 Flow (L/Min) Max Max 8 13 214 15 13 6 13 541 12 814 35 12 952 12 90 45 11 1232 55 6 15 3 16 25 5 25 398 24 534 24 804 23 944 23 78 22 1218 15 1494 11 16 29 0 29 391 29 528 29 792 28 9 28 64 26 1196 22 1480 18 1626 34 194 34 383 34 521 34 778 34 913 32 48 32 11 28 1466 13 43 187 43 374 43 513 43 763 43 897 41 24 41 1149 37 1438 1571 48 179 48 366 48 0 48 749 48 879 47 998 46 1118 44 16 38 1536 56 353 56 486 56 726 56 858 55 977 54 80 52 1367 49 12 324 76 458 76 701 76 833 943 74 44 71 19 67 1446 Flow (L/Min) Max Max 8 151 15 19 286 18 382 17 573 35 17 670 45 14 863 55 12 55 11 6 14 41 134 274 39 373 38 568 38 661 36 858 33 42 32 1143 25 14 56 115 56 261 55 361 55 558 54 652 53 849 28 47 1126 42 1416 69 90 71 243 71 348 71 535 69 6 67 837 65 64 1111 56 1395 89 56 91 4 92 318 91 3 89 6 88 807 85 979 83 79 76 1367 95 42 0 182 1 9 98 488 98 589 98 788 96 963 94 65 87 1351 112 139 117 287 116 462 117 562 114 764 111 947 8 43 1 1335 1 2 128 251 124 4 124 548 123 746 121 9 119 15 112 1312 BMP80 [77.7cm 3 /rev.] BMP0 [96.2cm 3 /rev.] Pressure (Bar) Pressure (Bar) 80 0 125 1 1 1 80 0 125 1 1 1 Flow (L/Min) Max Max 8 32 97 15 32 186 31 251 31 381 35 443 45 25 570 55 23 696 761 14 948 62 87 63 181 63 243 62 379 59 435 58 564 57 685 53 3 44 9 85 74 84 170 84 236 83 368 81 426 79 554 78 672 744 67 931 4 55 7 154 7 225 6 355 2 415 0 543 97 656 94 736 87 9 129 33 126 132 132 7 131 332 1 397 126 526 124 643 1 7 112 906 144 22 144 118 146 196 146 316 144 383 142 9 1 6 137 706 151 890 165 86 168 178 168 285 167 361 165 483 161 2 1 681 169 871 185 155 186 263 185 342 182 458 179 579 177 6 169 854 Flow (L/Min) Max Max 8 81 15 39 152 36 4 33 8 35 3 45 29 462 55 25 566 22 618 15 771 77 77 149 74 0 72 4 70 352 67 458 64 558 611 54 763 5 69 6 145 4 195 3 298 98 343 95 451 93 549 91 1 83 5 1 57 1 1 128 190 125 290 122 331 118 443 116 5 114 589 6 744 161 36 1 122 161 177 1 280 159 3 155 433 152 529 149 580 141 735 180 24 180 3 179 166 177 268 176 6 174 419 170 515 167 570 1 724 8 81 5 148 3 255 2 294 0 2 198 498 194 558 186 708 227 133 225 231 224 2 2 383 217 478 213 5 5 693 BMP125 [1.2cm 3 /rev.] BMP1 [157.2cm 3 /rev.] Pressure (Bar) Pressure (Bar) 80 0 125 1 1 1 80 0 125 1 1 1 Flow (L/Min) Max Max 8 51 63 15 51 121 48 162 46 243 35 42 284 45 37 370 55 33 452 29 490 18 615 98 1 116 98 158 96 239 92 279 89 362 84 446 78 482 66 6 137 55 138 1 135 153 132 234 1 274 125 355 122 438 117 4 7 598 168 47 168 2 167 148 164 227 1 269 157 348 152 431 146 468 133 586 8 28 9 89 211 137 9 216 6 259 1 3 196 4 191 459 179 5 236 15 236 73 237 128 232 2 229 247 224 327 218 412 215 448 2 563 267 48 269 9 264 189 2 231 261 3 252 2 248 439 236 549 290 94 287 176 284 222 281 296 2 384 272 427 2 528 Flow (L/Min) Max Max 8 62 49 15 93 57 125 53 187 35 49 2 45 44 283 55 345 33 377 19 473 1 48 122 91 1 123 115 184 1 216 2 280 99 342 94 374 80 469 170 46 172 88 170 1 164 181 1 213 154 276 148 3 144 371 124 465 212 42 215 85 214 117 6 178 2 9 196 272 191 336 188 367 170 459 263 26 264 76 262 1 259 1 255 5 248 267 243 331 236 363 216 453 290 14 294 68 290 6 288 168 284 2 278 2 272 328 267 359 252 447 3 48 3 92 335 155 328 192 321 2 316 3 8 353 296 4 371 81 368 139 362 176 358 238 351 3 345 342 325 424 Torque (Nm) 124 Speed (rpm) 465 12
PERFORMANCE DATA BMP0 [194.5cm 3 /rev.] BMP2 [2.3cm 3 /rev.] Pressure (Bar) Pressure (Bar) 80 0 125 1 1 1 80 0 125 1 1 1 Flow (L/Min) Max Max 8 79 15 78 76 76 0 70 151 35 66 177 45 63 228 55 54 280 38 4 22 382 164 39 162 158 98 153 149 149 1 146 226 1 278 127 2 96 378 7 38 5 74 3 97 0 147 194 173 190 224 181 276 164 0 145 374 2 35 2 71 247 95 245 145 232 171 2 221 224 274 212 297 192 371 3 28 322 66 3 92 315 142 297 168 294 218 286 271 270 294 235 368 3 22 361 61 358 89 3 139 343 166 3 215 334 269 325 291 293 364 4 51 3 73 398 131 386 1 383 2 371 263 356 286 321 3 422 57 417 1 415 149 4 198 0 2 395 272 367 3 Flow (L/Min) Max Max 8 96 15 98 92 82 85 123 35 77 143 45 70 185 55 63 226 248 34 9 190 28 194 58 188 80 180 1 176 141 168 182 159 223 1 246 128 6 268 24 270 54 267 77 259 118 252 139 243 178 237 218 228 243 2 2 326 21 327 325 76 3 114 311 135 0 174 290 213 280 239 264 297 3 11 5 5 69 0 6 389 128 377 168 369 9 358 233 342 292 4 456 64 448 98 436 122 428 161 417 2 7 226 387 286 5 12 514 52 513 87 4 112 495 152 483 193 473 215 448 278 565 38 561 76 557 1 543 139 531 185 5 7 488 264 BMP315 [314.5cm 3 /rev.] BMP0 [389.5cm 3 /rev.] Pressure (Bar) Pressure (Bar) 70 90 0 125 1 45 55 65 80 0 125 Flow (L/Min) Max Max 8 123 25 15 118 47 1 62 1 94 35 96 9 45 89 141 55 76 173 65 188 236 215 23 211 46 5 61 196 93 188 7 180 1 166 172 154 186 1 234 292 21 287 44 278 271 91 264 6 254 138 239 170 227 184 1 232 368 17 367 3 57 349 88 341 4 337 135 325 167 8 182 279 228 5 11 4 28 395 46 388 76 382 96 372 127 362 1 348 178 323 226 495 21 494 490 68 478 89 468 1 457 152 443 172 418 223 568 566 36 565 65 557 84 553 115 548 143 529 163 497 214 Flow (L/Min) Max Max 8 166 15 165 38 162 154 76 35 146 88 45 132 114 55 117 139 2 153 53 191 232 19 228 36 223 49 216 2 87 197 113 184 137 163 152 128 189 287 18 277 35 273 49 266 74 256 87 243 112 227 136 215 1 182 187 3 16 337 33 331 48 318 73 312 86 0 1 283 135 272 148 234 185 418 12 417 31 413 45 5 71 395 83 383 8 363 135 347 146 318 183 496 27 495 41 486 67 480 80 464 6 4 132 436 143 391 180 612 21 8 35 0 588 576 99 552 123 532 138 484 176 BMP0 [486.5cm 3 /rev.] Pressure (Bar) 15 45 70 80 90 Torque (Nm) 234 Speed (rpm) 185 Flow (L/Min) Max Max 4 96 7 8 98 15 15 96 96 91 61 86 81 78 2 66 122 70 52 143 35 153 194 6 1 15 192 191 185 172 80 1 1 134 121 111 142 83 152 285 4 4 14 284 29 280 272 261 80 241 0 213 1 189 141 154 151 391 14 380 28 372 39 3 58 343 79 332 98 5 119 292 139 241 1 443 12 421 26 418 37 412 56 8 76 391 96 371 117 344 137 312 149 512 9 496 23 493 33 486 53 480 73 466 93 438 114 418 135 389 147 574 7 5 22 546 31 541 538 70 528 90 496 1 4 131 447 144 Torque (Nm) 312 Speed (rpm) 149 13
BMP DIMENSIONS AND MOUNTING DATA 14
BMPH DIMENSIONS AND MOUNTING DATA 15
BMP SHAFT EXTENSIONS DIMENSIONS DATA 16
BMP SHAFT EXTENSIONS DIMENSIONS DATA Motor Mounting Surface 17
BMPH SHAFT EXTENSIONS DIMENSIONS DATA Motor Mounting Surface 18
BMPH SHAFT EXTENSIONS DIMENSIONS DATA Motor Mounting Surface 19
BMPW DIMENSIONS & MOUNTING DATA
BMPW ORDER INFORMATION 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Code Disp Flange Output Shaft Main Port & Drain Port Rotation Direction Paint Special Function BMPW 80 0 125 1 0 2 315 0 0 Omit Wheel-Flange Pilot 80x7.5 A C E T Shaft 25k6, Parallel Key 8x7x32 Shaft 25.4, Parallel Key 6.35x6.35x31. Shaft 25.4, Splined Key SAE 6B Cone Shaft 28.56, Parallel Key B5x5x14 G S M G1/2, G1/4 7/8-14 Oring, 7/16-UNF M22x1.5, M14x1.5 Omit R Standard Opposite 00 Omit B S No Paint Blue Black Silver Grey Omit N O Standard High radial force No case drain 21
BMP, BMPH, BMPW SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE Bar In applications without drain line, the shaft seal pressure is equal to the pressure in the return line. When applications use the drain line, the pressure behind the output shaft seal equals the pressure in drain line. DIRECTION OF SHAFT ROTATION When facing shaft end of motor, shaft to rotate: Clockwise when Port A is pressurised Counter-clockwise Port B is pressurised STATUS OF THE SHAFT S RADIAL FORCE 22
ORDER INFORMATION 1 2 3 4 5 6 7 8 Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 A Shaft 25, Parallel Key 8x7x32 D G1/2 Manifold Mount 4xM8, G1/4 B Shaft 32, Parallel Key x8x45 80 C Shaft 25.4, Parallel Key 6.35x6.35x31. M M22x1.5 Manifold Mount 4xM8, 0 E Shaft 25, Splined Tooth SEA 6B M14x1.5 Omit Standard 2 2-13.5 Rhomb-Flange, Pilot 82.5x8 125 R 00 No Paint N Large Radial Force Short shaft 25.4, Parallel Key 6.35x6.35x31. 4 4-13.5 Rhomb-Flange, Pilot 82.5x8 S 7/8-14 O-Ring Manifold 4x5/16- Omit Standard Omit Blue AX Large Axial Force BMP 1 F H4 Shaft 31., Splined Tooth 14-DP12/24 4-3/8-16 Square-Flange, Pilot 44.4x2.8 18UNC, 7/16-UNF R Opposite B Black O No Case Drain 0 H5 FD 4-M Square-Flange, Pilot 44.4x2.8 Long Shaft 31., Splined Tooth 14-DP12/24 S Silver Grey F Free Running 2 G Shaft 31., Parallel Key 7.96x7.96x31. P 1/2-14 NPFT Manifold 4x5/16- LS Low Speed 315 T Cone Shaft 28.56, Parallel Key B5x5x14 18UNC, 7/16-UNF 0 T3 Cone Shaft 31., Parallel Key 7.96x7.96x25.4 0 R PT(Rc)1/2 Manifold 4xM8,PT(Rc)1/4 1 2 3 4 5 6 7 8 Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 K Shaft 25.4, Woodruff Key 25.4x6.35 S Shaft 25.4, Splined Tooth SEA 6B G 80 A Shaft 25, Parallel Key 8x7x32 S P T BMPH R Omit Standard B4 R Opposite 0 R Shaft 25.4, Parallel Key 6.35x6.35x31. 125 H2 2-13.5 Rhomb-Flange, Pilot 82.5x2.8 H Shaft 25.4, Pin Hold.3 H4 4-13.5 Rhomb-Flange, Pilot 82.5x2.8 1 H1 Shaft 25.4, Pin Hole 8 H4 4-3/8-16 Square-Flange, Pilot 44.4x2.8 0 H5 D Shaft 22.22, Parallel Key 6.35x6.35x25.4 4-M Square-Flange, Pilot 44.4x2.8 2 I Shaft 22.22, Splined Tooth 13-DP16/32 315 T2 Cone Shaft 25.4, Woodruff Key 25.4x6.35 0 P Shaft 25, Parallel Key 8x7x28 0 J Shaft 25, Parallel Key 7x7x32 B5 G1/2 G1/4 7/8-14 O-Ring 7/16-UNF (G1/4) 1/2-14 NPTF, 7/16-UNF (G1/4) 3/4-16 O-Ring, 7/16-UNF PT(Rc)1/2 PT(Rc)1/4 O-Ring Manifold 4x5/16-18UNC, 7/16-UNF(G1/4) O-Ring Manifold 4xM8 7/16- UNF(G1/4) 00 Omit B S No Paint Blue Black Silver Grey Omit N AX O F LS Standard Large Radial Force Large Axial Force No Case Drain Free Running Low Speed 23
BMR SERIES HYDRAULIC MOTOR BMR Series motors are medium speed high torque motors designed on an internal gear design consisting of a rotor and stator. These motors are suitable for long operating periods at moderate pressures. Characteristic Features: Advanced manufacturing design for the Geroler gear set, which provide high starting torque, high efficiency and long life Motors have high pressure shaft seals which can be used in Parallel or Series Smooth running over the entire speed range Main Specifications Type BMR & BMRS 36 80 0 125 1 0 2 315 3 Geometric Displacement (cm 3 /rev.) 36 51.3 80.6 0.8 124.9 157.2 199.2 252 314.5 370 Speed (rpm) 85 5 0 0 4 3 0 2 190 1 12 970 9 0 0 470 3 0 2 0 Torque (Nm) Rated 69 0 1 0 2 3 3 352 3 4 69 0 190 2 292 363 358 352 3 4 88 126 2 280 3 4 448 470 470 548 Output (kw) Rated 7.5 7.7 12.3 12.3 12.0 12.3 9 7 6.5 7.5 7.7 15 15 14 14 11 9 7 8.6 9.4 9.7 17 17 16 16 14 12 9 12 Pressure Drop (Bar) Rated 1 1 1 1 1 1 1 1 85 85 1 1 1 1 1 165 1 1 85 85 1 1 0 0 0 0 1 1 115 115 Flow (L/min) Weight (kg) 6.7 6.7 6.9 6.9 7.2 7.5 8.0 8.5 9 9.3 Rated Speed & Rated Torque: Output value of speed and torque under rated flow and rated pressure Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute 24
PERFORMANCE DATA BMR [51.3cm 3 /rev.] BMR80 [80.6cm 3 /rev.] Pressure (Bar) Pressure (Bar) 70 90 0 1 1 1 1 70 90 0 1 1 1 1 5 35 95 45 84 61 76 67 73 77 69 88 46 55 115 77 9 98 6 7 1 1 91 149 170 53 180 45 Flow (L/min) 15 36 184 35 283 34.5 377 46 176 49 277 47 3 62 165 63 269 61 365 69 162 73 261 69 361 80 1 88 2 83 346 95 1 0 2 96 3 8 111 9 211 9 8 1 84 123 185 126 276 Flow (L/min) 239 48 364 45 488 81.6 235 74 3 71 483 5 227 97 357 95 4 118 224 114 345 5 472 132 9 131 332 128 4 1 196 1 321 149 447 178 172 179 0 177 4 189 1 190 284 188 8 25 34 476 45 468 61 4 69 453 81 438 96 423 9 395 126 361 42 619 70 615 90 7 98 598 125 593 147 568 171 547 187 535 33 576 44 569 561 67 554 80 542 95 531 8 0 126 465 38 7 63 725 85 721 95 715 118 707 142 688 169 667 185 657 35 31 669 42 665 59 657 66 654 80 638 93 623 7 598 124 561 70 36 8 58 853 80 839 89 837 112 823 139 811 164 790 179 776 7 41 8 58 3 66 0 79 738 92 724 6 700 122 670 29 925 56 915 77 9 85 899 1 888 133 871 161 853 177 837 45 29.5 856 856 57 8 65 845 78 835 90 815 5 799 121 780 BMR0 [0.8cm 3 /rev.] BMR125 [124.9cm 3 /rev.] Pressure (Bar) Pressure (Bar) 70 90 0 1 1 1 1 70 90 0 1 1 1 1 70 99 0 95 122 87 138 84 159 74 182 63 2 52 222 44 90 73 122 71 1 66 173 63 5 55 237 42 258 23 270 14 Flow (L/min) 68 199 62 299 59 0 95 194 94 294 88 398 123 188 121 288 119 387 143 182 1 284 134 385 165 1 164 278 161 380 0 162 194 263 192 366 221 1 2 249 218 3 238 138 2 236 238 336 Flow (L/min) 85 154 82 237 79 315 118 152 7 236 5 313 159 1 158 233 1 9 172 145 164 226 161 7 8 138 6 219 4 2 2 123 241 7 238 297 278 9 277 192 2 272 292 91 291 170 289 254 55 498 83 496 117 488 125 484 157 4 185 464 217 4 235 436 398 96 397 145 395 1 391 198 381 236 368 262 353 282 337 48 599 79 595 1 587 119 585 152 579 180 569 214 552 233 538 62 4 95 473 139 471 158 470 183 463 222 4 254 427 279 416 70 43 699 70 693 0 687 112 683 142 679 170 668 1 648 229 636 70 59 554 83 553 125 551 1 5 178 546 212 538 2 514 262 0 39 748 63 741 97 737 5 735 1 7 167 713 197 697 227 686 56 598 80 597 122 593 145 590 172 586 5 577 245 551 261 537 Cont Torque (Nm) 167 Speed (rpm) 713 25
PERFORMANCE BMR1 [157.2cm 3 /rev.] BMR0 [199.2cm 3 /rev.] Pressure (Bar) Pressure (Bar) 70 90 0 1 1 1 1 70 90 5 1 1 1 115 58 1 55 3 52 2 2 44 0 38 3 34 362 26 148 49 5 47 255 45 290 43 327 370 442 24 Flow (L/min) 114 119 5 184 0 246 1 115 158 181 145 244 5 111 2 177 196 239 2 8 221 172 218 237 265 3 261 165 257 2 3 95 5 153 299 218 355 84 344 134 3 199 380 76 378 1 374 184 Flow (L/min) 1 99 1 149 125 0 2 97 193 146 186 197 2 93 241 1 232 192 323 90 7 136 5 188 3 86 325 131 313 181 411 78 377 122 390 170 448 65 445 5 436 149 90 7 1 5 190 2 9 0 2 292 295 280 336 262 366 244 1 2 177 247 225 242 295 238 5 231 382 218 427 193 84 370 136 368 180 364 199 362 2 355 286 342 3 334 3 4 1 0 166 298 221 291 285 287 292 282 372 268 419 236 70 65 435 1 434 164 4 180 427 223 416 280 5 3 335 3 366 70 98 3 1 347 5 342 244 338 278 331 331 318 4 282 59 465 116 462 158 458 1 456 2 447 272 433 314 416 342 395 85 3 141 372 199 366 235 362 268 357 323 343 0 3 BMR2 [252cm 3 /rev.] BMR315 [314.5cm 3 /rev.] Pressure (Bar) Pressure (Bar) 70 80 0 1 1 1 65 80 90 1 135 115 180 38 251 37 295 35 3 32 380 470 22 535 16 135 31 215 29 279 28 343 27 383 27 515 24 5 22 Flow (L/min) 1 79 0 1 91 158 178 78 170 119 159 157 252 248 117 232 156 294 74 285 116 268 154 352 70 348 1 332 151 385 68 381 7 366 148 470 57 469 95 4 1 548 48 545 79 5 1 Flow (L/min) 133 62 125 95 113 123 216 61 5 92 195 121 289 2 91 267 1 349 58 341 90 335 118 380 57 3 88 367 117 8 52 494 81 485 6 552 543 79 526 4 81 0 148 198 216 196 252 195 3 163 352 1 453 152 521 147 92 155 170 154 253 152 321 149 352 147 474 137 511 133 241 132 2 1 239 235 237 5 232 3 228 433 2 5 180 80 190 1 187 231 193 5 179 334 176 458 163 492 157 70 280 117 279 189 277 2 276 290 271 3 268 412 2 495 215 70 57 222 136 2 215 217 285 212 3 8 444 192 480 185 42 0 5 299 180 298 211 297 281 295 3 289 5 272 486 239 55 235 124 234 5 231 269 227 8 225 427 8 469 1 Cont Torque (Nm) 5 Speed (rpm) 231 26
PERFORMANCE BMR3 [370cm 3 /rev.] Pressure (Bar) 65 80 90 1 135 1 26 270 25 3 24 4 22 470 21 5 19 6 17 Flow (L/min) 159 53 1 79 135 6 2 52 255 78 2 5 3 51 3 77 3 4 4 49 0 3 2 470 47 4 73 4 99 5 42 5 67 5 93 5 37 0 590 85 1 134 2 132 295 131 3 129 4 126 5 1 570 1 98 159 2 158 2 157 3 155 390 153 490 147 5 135 70 187 1 186 2 185 3 183 370 180 465 1 5 1 65 0 1 199 2 198 3 195 3 192 4 187 515 178 Cont Torque (Nm) 2 Speed (rpm) 198 27
BMR DIMENSIONS AND MOUNTING DATA 28
BMRS DIMENSIONS AND MOUNTING DATA 29
BMR SHAFT EXTENSIONS DIMENSIONS DATA
BMRS SHAFT EXTENSIONS DIMENSIONS DATA 31
BMRS SHAFT EXTENSIONS DIMENSIONS DATA 32
BMR, BMRS SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE Bar In applications without drain line, the shaft seal pressure is equal to the pressure in the return line. When applications use the drain line, the pressure behind the output shaft seal equals the pressure in drain line. DIRECTION OF SHAFT ROTATION When facing shaft end of motor, shaft to rotate: Clockwise when Port A is pressurised Counter-clockwise Port B is pressurised STATUS OF THE SHAFT S RADIAL FORCE 33
ORDER INFORMATION 1 2 3 4 5 6 7 8 Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 A Shaft 25, Parallel Key 8x7x32 D G1/2 Manifold Mount 4xM8, G1/4 B Shaft 32, Parallel Key x8x45 80 C Shaft 25.4, Parallel Key 6.35x6.35x31. M M22x1.5 Manifold Mount 0 E Shaft 25, Splined Tooth SEA 6B 4xM8, M14x1.5 Omit Standard 2 2-13.5 Rhomb-Flange, Pilot 82.5x8 00 No Paint N Large Radial Force 125 R Short shaft 25.4, Parallel Key 6.35x6.35x31. 4 4-13.5 Rhomb-Flange, Pilot 82.5x8 S 7/8-14 O-Ring Manifold Omit Standard Omit Blue AX Large Axial Force BMR 1 H4 F 4-3/8-16 Square-Flange, Pilot 44.4x2.8 Shaft 31., Splined Tooth 14-DP12/24 4-5/16-18UNC, 7/16-UNF R Opposite B Black O No Case Drain 0 H5 4-M Square-Flange, Pilot 44.4x2.8 FD Long Shaft 31., Splined Tooth 14-DP12/24 S Silver Grey F Free Running 2 G Shaft 31., Parallel Key 7.96x7.96x31. P 1/2-14 NPFT Manifold LS Low Speed 315 T Cone Shaft 28.56, Parallel Key B5x5x14 4-5/16-18UNC, 7/16-UNF 0 T3 Cone Shaft 31., Parallel Key 7.96x7.96x25.4 R PT(Rc)1/2 Manifold 4-M8,PT(Rc)1/4 1 2 3 4 5 6 7 8 Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 K Shaft 25.4, Woodruff Key 25.4x6.35 D G1/2 Manifold Mount 4-M8, G1/4 S Sub-Shaft 25.4, Splined Tooth SAE 6B 80 A Shaft 25, Parallel Key 6.35x6.35x31. M M22x1.5 Manifold Mount 4-0 R Shaft 25.4, Splined Tooth SAE 6B M8,M14x1.5 Omit Standard 125 H2 2-13.5 Rhomb-Flange, Pilot 82.5x2.8 H Short Shaft 25.4, Parallel Key 00 No Paint N Large Radial Force S 7/8-14 O-Ring Manifold 4-5/16- H6 4-13.5 Rhomb-Flange, Pilot 82.5x2.8 6.35x6.35x31. Omit Standard Omit Blue AX Large Axial Force BMRS 18UNC, 7/16-UNF 1 H4 4-3/8-16 Square-Flange, Pilot 44.4x2.8 H1 Shaft 31., Splined Tooth 14-DP12/24 R Opposite B Black O No Case Drain 0 H5 4-M Square-Flange, Pilot 44.4x2.8 D Long Shaft 31., Splined Tooth 14-DP12/24 S Silver Grey F Free Running P 1/2-14 NPTF Manifold 4-5/16-16- 2 I Shaft 31., Parallel Key 7.96x7.96x31. LS Low Speed 18UNC, 7/16-UNF 315 T2 Cone Shaft 28.56, Parallel Key B5x5x14 3 P R PT(Rc)1/2 Manifold 4-M8, PT(Rc)1/4 J 34
BMH SERIES HYDRAULIC MOTOR BMH Series motors are medium speed, high torque motors designed on an internal gear design consisting of a rotor and stator. These motors are suitable for long operating periods at moderate pressures. Characteristic Features: Advanced manufacturing design of the Geroler gear set, which provide high starting torque, high efficiency and long life Motors have high pressure shaft seals which can be used in Parallel or Series Smooth running over the entire speed range Main Specifications Type BMH 0 2 315 0 0 Geometric Displacement (cm 3 /rev.) 3.2 255.9 316.1 6.4 489.2 Speed (rpm) 366 290 236 183 155 439 348 282 2 166 Torque (Nm) 5 621 7 8 8 579 702 827 990 Peak 651 790 9 92 1170 Output (kw) 16 16 14 12.5 11 18.5 18.5 15.5 15 14 Pressure Drop (Bar) 1 1 1 155 125 0 0 0 190 1 Peak 225 225 225 2 180 Flow (L/min) 90 90 90 90 90 Weight (kg).5 11 11.5 12.3 13 Type Inlet Pressure Return Pressure with Drain Line 1 1 BMH 0-0 (Bar) 0 0 Peak 225 225 Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute Technical data BMH with 35mm cylindrical, 1 ¼ in splined and 35mm tapered shaft 35
36 PERFORMANCE DATA BMH0 [3.2cm 3 /rev.] BMH2 [255.9cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) Flow (L/min) 35 70 5 1 1 0 Flow (L/min) 35 70 90 1 145 1 0 5 98 25 194 25 284 22 5 121 19 246 19 318 18 398 14 1 43 4 41 1 36 391 29 482 14 1 34 258 33 331 31 425 29 515 23 595 12 99 0 1 97 4 93 2 85 9 69 576 56 1 78 258 77 332 76 432 73 5 65 621 53 702 42 97 145 197 143 0 139 2 1 5 114 579 1 122 115 251 113 327 111 429 5 5 96 621 84 700 90 0 190 0 292 0 399 188 7 168 578 153 115 157 2 157 323 156 422 1 513 139 616 127 698 114 82 248 183 246 284 244 392 235 0 213 571 199 5 196 232 195 314 192 411 185 5 173 6 159 687 147 73 292 174 290 274 287 384 279 493 2 563 244 94 232 2 2 2 226 1 218 496 6 596 192 676 180 70 63 352 163 3 264 349 374 338 481 318 554 1 70 81.4 274 9 274 288 274 389 266 484 252 582 238 666 222 59 366 157 365 259 363 366 355 4 335 547 319 72 290 3 289 280 287 381 279 4 266 574 251 659 236 80 53 381 1 381 253 380 358 371 466 352 538 338 80 66 3 194 2 273 298 371 290 467 279 566 264 651 249 90 39 443 1 437 241 434 348 426 456 7 526 392 90 49 348 178 347 256 345 355 337 453 325 552 9 634 292
PERFORMANCE DATA BMH315 [316.1cm 3 /rev.] BMH0 [6.4cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) 35 0 135 155 1 0 35 5 125 155 190 5 155 16 325 13 5 196 13 348 13 516 163 27 342 24 454 18 556 14 5 22 363 21 546 21 702 17 859 11 Flow (L/min) 169 63 165 93 154 126 349 61 344 89 337 126 469 55 470 82 465 119 582 48 580 77 577 111 664 669 67 663 99 733 32 7 59 737 88 809 19 824 46 827 73 Flow (L/min) 9 1 73 195 99 366 49 357 72 346 98 543 46 542 70 532 96 708 41 706 63 701 86 874 36 864 56 858 77 988 31 984 51 973 71 141 159 325 155 455 148 568 139 656 126 728 115 824 98 173 123 332 122 518 118 687 7 848 97 958 90 121 187 312 186 4 179 555 169 643 154 715 143 812 124 154 146 319 144 1 141 688 128 833 115 944 6 70 3 222 298 222 425 215 541 5 631 187 703 176 800 157 70 138 174 5 173 480 169 649 156 814 141 925 1 94 236 287 233 417 224 529 215 623 196 696 184 792 166 128 183 294 181 466 177 637 163 802 149 911 138 80 82 246 277 244 6 236 518 228 611 2 688 197 784 174 80 113 192 277 191 451 188 621 174 786 158 899 144 90 62 282 256 280 386 2 496 266 593 248 669 234 767 9 90 90 2 256 2 433 215 595 2 767 183 881 165 Cont Torque (Nm) 593 Speed (rpm) 248 37
PERFORMANCE DATA BMH0 [0cm 3 /rev.] Pressure (Bar) Cont 25 85 0 125 1 5 165 11 317 11 516 8 178 335 19 555 17 669 15 791 13 969 9 Flow (L/min) 177 42 172 64 163 85 331 42 3 63 9 85 559 41 553 61 541 83 673 38 663 57 654 79 799 36 792 53 783 988 29 983 47 971 67 146 3 296 3 523 3 635 97 768 93 954 85 121 124 2 124 2 123 614 117 747 113 934 3 70 97 148 256 148 482 148 597 1 729 134 917 122 79 155 2 155 469 155 582 152 714 144 902 1 80 166 226 166 453 166 570 159 701 153 884 139 90 34 166 1 165 421 164 5 157 673 156 869 155 Cont Torque (Nm) 673 Speed (rpm) 156 38
BMH DIMENSIONS AND MOUNTING DATA 39
BMH SHAFT EXTENSIONS DIMENSIONS DATA
BMH SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE In applications without drain line, output shaft seal exceeds a bit of the pressure in the return line. When applications use the drain line, the pressure of output shaft seal equals the pressure in drain line. DIRECTION OF SHAFT ROTATION: STANDARD When facing shaft end of motor, shaft to rotate: Clockwise when Port A is pressurised Counter-clockwise Port B is pressurised STATUS OF THE SHAFT S RADIAL FORCE 41
ORDER INFORMATION 1 2 3 4 5 6 7 8 Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 1 B Shaft 32, Parallel Key x8x45 G1/2 Manifold Mount 4xM8, G1/4 D 0 M Shaft 35, Parallel Key x8x45 2 F Shaft 31., Splined Key 14-DP12/24 M22x1.5 Manifold Mount M 315 FD 4xM8, M14x1.5 Long Shaft 31., Splined Key 14-DP12/24 0 G Shaft 32, Parallel Key 7.96x7.96x31. 00 No Paint Omit Standard 2 2-13.5 Rhomb-Flange, Pilot 82.5x8 7/8-14 O-Ring Manifold Mount S Omit Standard Omit Blue O No Drain BMH 0 T1 Cone Shaft 35, Parallel Key B6x6x 4xM8, 7/16-UNF R Opposite B Black F Free Running 4 4-13.5 Rhomb-Flange, Pilot 82.5x8 S Shaft 25.4, Parallel Key SAE 6B S Silver Grey LS Low Speed 1/2-14 NPFT Manifold Mount P 4xM8, 7/16-UNF R PT(Rc)1/2 Manifold Mount 4-M8,PT(Rc)1/4 42
BMJ SERIES HYDRAULIC MOTOR BMJ series motors have an advanced Geroller gear set, designed to accommodate high speed flow and pressure. These units have good stability at low speed, keeping high volumetric efficiency. Features Advanced design for the Geroller gear set, allowing low pressure start-up, provides smooth and reliable operation together with high efficiency Output shaft fitted with needle roller bearings permitting high axial and radial forces Advanced design in flow distribution automatically compensating resulting in high volume efficiency and long life, providing smooth and reliable operation Low leakage rate, accurate internal timing. Commutator rotates 6x faster than shaft output speed giving high precision and reduces life-cycle cost, maintaining high volume efficiencies and ability to run smoothly at low speed Specification Type 65 80 0 125 1 0 2 2 295 315 3 Geometric Displacement (cm 3 /rev) 66.8 81.3 1.6 127 157.2 193.6 226 257 287.8 314.5 370 Max Speed (rpm) Cont 667 543 439 3 283 229 247 216 196 178 152 Int 842 689 553 441 355 289 328 287 254 235 199 Max Torque (Nm) Cont 126 157 191 245 7 382 378 381 393 448 439 Int 176 215 268 335 422 5 528 543 547 587 613 Max Output (kw) Cont 8.3 8.8 7.9 8.9 8.9 9 9.9 9.3 8.7 8 7.6 Int 13.9 14.4 13.5 14.1 15.6 15.7 17.9 16.5 15.6 14.3 14 Max Pressure (Bar) Cont 1 1 1 1 1 1 1 1 0 0 90 Int 190 190 190 190 190 190 165 155 145 135 125 Peak 0 0 0 0 0 0 180 180 170 1 1 Max Flow (L/min) Cont 45 45 45 45 45 45 57 57 57 57 57 int 57 57 57 57 57 57 Continuous Pressure: Max value of operating motor continuously Intermittent Pressure: Max value of operating motor in 6 seconds per minute Peak Pressure: Max value of operating motor in 0.6 seconds per minute 43
Dimensions Mounting Data BMJ SERIES HYDRAULIC MOTOR Wheel Mount Code: WS Ports A, B, 7/8 14 O-Ring Code: WD Ports A, B, G1/2 Code: WM Ports A, B, M22x1.5 Displacement (cm 3 /rev) 65 80 0 125 1 0 2 2 295 315 3 L1 (mm) 13 16 25.5 38.1 44 56 62 74 L (mm) 115 118 122 127 132.5 1 146 152 158 164 176 Weight (kg) 9 9.1.4.6.9 11.3 11.8 12.2 12.6 12.9 13.4 Side Load (dan) The bearing curve represents allowable bearing loads for an L bearing life at 3x 6 revolutions The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads Distance from Mounting Face (mm) 44
ORDER INFORMATION BMJ 1 2 3 4 5 6 7 1 2 3 4 5 6 7 Code Disp Flange, Pilot, Ports Output Shaft Rotation Direction Paint Unusually Function Cone-Shaft 35, Parallel Key B6x6x Omit 65 80 0 125 1 0 2 2 295 315 3 WS WD WM 4-13.5 Wheel- Flange, Pilot 82.55x7, Port 7/8-14 O-Ring 4-13.5 Wheel- Flange, Pilot 82.55x7, Port G1/2 4-13.5 Wheel- Flange, Pilot 82.55x7, Port M22x1.5 T1 T2 T3 T4 B Cone-Shaft 31., Woodruff Key 25.4x7.96 Cone-Shaft 31., Parallel Key 7.96x7.96x31. Cone-Shaft 31., Parallel Key 7.96x7.96x25.4 Cylindrical Shaft 32, Parallel Key x8x45 Omit R Standard Opposite 00 Omit B S No Paint Blue Black Silver Grey Omit Standard Shaft Extensions for Dimensions Data Motor Mounting Surface 45
VALVES FOR HYDRAULIC MOTORS SHUTTLE VALVE Code: VSEFMDSE Max Flow L/min Max Pressure 3 Bar V1 V2 ½ BSPP C3 ¼ BSPP CROSSLINE RELIEF WITH BRAKE RELEASE SHUTTLE VALVE Code: VSFMDISE / 1Y04B -1 Bar Adjustment Code: VSFMDISE / 1Z04B 0-280 Bar Adjustment Max Flow Max Pressure V1 V2 C3 L/min 2 Bar ½ BSPP ¼ BSPP 46
VALVES FOR HYDRAULIC MOTORS ROTARY DIRECTIONAL VALVE WITH RELIEF Code: VIBFMDVS04B Max Flow 35L/min Max Pressure -1 Bar V1 V2 ½ BSPP DUAL OVERCENTRE VALVE WITH BRAKE RELEASE SHUTTLE VALVE Code: VB048FMDSECA12AX Pilot Ratio 7:1 Adjustment -1 Bar Max Flow L/min V1 V2 ½ BSPP C3 ¼ BSPP 47
48